| Age | Commit message (Collapse) | Author |
|---|
|
Under "heavy" RX load, the driver cannot handle the descriptors fast
enough. In detail, when a descriptor is consumed, its used flag is
cleared and once the RX budget is consumed all descriptors with a
cleared used flag are prepared to receive more data. Under load though,
the HW may constantly receive more data and use those descriptors with a
cleared used flag before they are actually prepared for next usage.
The head and tail pointers into the RX-ring should always be valid and
we can omit clearing and checking of the used flag.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Coverage data suggests that the unlikely case of receiving data while
the receive handler is running may not be that unlikely.
Coverage data after running iperf for a while:
91320: 891: work_done = bp->macbgem_ops.mog_rx(bp, budget);
91320: 892: if (work_done < budget) {
2362: 893: napi_complete(napi);
-: 894:
-: 895: /* Packets received while interrupts were disabled */
4724: 896: status = macb_readl(bp, RSR);
2362: 897: if (unlikely(status)) {
762: 898: if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
762: 899: macb_writel(bp, ISR, MACB_BIT(RCOMP));
-: 900: napi_reschedule(napi);
-: 901: } else {
1600: 902: macb_writel(bp, IER, MACB_RX_INT_FLAGS);
-: 903: }
-: 904: }
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When data is received during the driver processing received data the
NAPI is re-scheduled. In that case the RX interrupt should not be
re-enabled.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A few interrupt flags were not cleared in the ISR, resulting in a sytem
trapped in the ISR in cases one of those interrupts occurred. Clear all
flags to avoid such situations.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just as commit "net: macb: DMA-unmap full rx-buffer"
(48330e08fa168395b9fd9f369f06cca1df204361), pass the size that
was used for mapping the memory also to the unmap routine to
avoid warnings from the DMA_API.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000e only.
David provides four fixes for e1000e, first is a workaround for a hardware
erratum on 82579 devices which experienced packet loss in gigabit and 100
speeds when interconnect between the PHY and MAC is exiting K1 power saving
state. Second expands the scope of a workaround to include i217 and i218
parts as well to address over aggressive transmit behavior when connecting
at 10Mbs half-duplex. Next is to resolve a reported link flap issue on
82579 parts which was root caused as an interoperability problem between
82579 and at least some Broadcom PHYs in the Energy Efficient Ethernet wake
mechanism. Lastly, restricts the workaround of putting the PHY into MDIO
slow mode to access the PHY id to relevant parts since this issue has been
fixed on the newer hardware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It has been determined that the workaround of putting the PHY into MDIO
slow mode to access the PHY id is not necessary with Lynx Point and newer
parts. The issue that necessitated the workaround has been fixed on the
newer hardware.
We will maintains, as a last ditch attempt, the conversion to MDIO Slow
Mode in the failure branch when attempting to access the PHY id so as to
cover all contingencies.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Several customers have reported a link flap issue on 82579. The symptoms
are random and intermittent link losses when 82579 is connected to specific
link partners. Issue has been root caused as interoperability problem
between 82579 and at least some Broadcom PHYs in the Energy Efficient
Ethernet wake mechanism.
To fix the issue, we are disabling the Phase Locked Loop shutdown in 100M
Low Power Idle. This solution will cause an increase of power in 100M EEE
link. It will cost additional 28mW in this specific mode.
Cc: Lukasz Adamczuk <lukasz.adamczuk@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In commit 772d05c51c4f4896c120ad418b1e91144a2ac813 "e1000e: slow performance
between two 82579 connected via 10Mbit hub", a workaround was put into place
to address the overaggressive transmit behavior of 82579 parts when connecting
at 10Mbs half-duplex.
This same behavior is seen on i217 and i218 parts as well. This patch expands
the original workaround to encompass these parts.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This is a workaround for a HW erratum on 82579 devices.
Erratum is #23 in Intel 6 Series Chipset and Intel C200 Series Chipset
specification Update June 2013.
Problem: 82579 parts experience packet loss in Gig and 100 speeds
when interconnect between PHY and MAC is exiting K1 power saving state.
This was previously believed to only affect 1Gig speed, but has been observed
at 100Mbs also.
Workaround: Disable K1 for 82579 devices at Gig and 100 speeds.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Carrying out PCI speed/width checks through pcie_get_minimum_link()
on VFs yield wrong results, so remove them.
Fixes: b912b2f ('net/mlx4_core: Warn if device doesn't have enough PCI bandwidth')
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running in SRIOV mode, VM that is assigned with a non-provisioned
Ethernet VFs get themselves a random mac when the Eth driver starts. In
this case, if the IB driver startup code that deals with RoCE runs first,
it will use a zero mac as the source mac for the Para-Virtual CM MADs
which is buggy. To handle that, we change the order of loading.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code that deals with computing the slave id based on a given GID
gave wrong results when the number of single port VFs wasn't the
same for port 1 vs. port 2 and the relevant VF is single ported on
port 2. As a result, incoming CM MADs were dispatched to the wrong VF.
Fixed that and added documentation to clarify the computation steps.
Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using single ported VFs and the VF is using port 2, we need
to adjust the port accordingly (change it from 1 to 2).
Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4d619f625a60 ("net: cdc_ncm: no point in filling up the NTBs
if we send ZLPs") changed the padding logic for devices with the ZLP
flag set. This meant that frames of any size will be sent without
additional padding, except for the single byte added if the size is
a multiple of the USB packet size. But if the unpadded size is
identical to the maximum frame size, and the maximum size is a
multiplum of the USB packet size, then this one-byte padding will
overflow the buffer.
Prevent padding if already at maximum frame size, letting usbnet
transmit a ZLP instead in this case.
Fixes: 4d619f625a60 ("net: cdc_ncm: no point in filling up the NTBs if we send ZLPs")
Reported by: Yu-an Shih <yshih@nvidia.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If NO_DMA=y:
drivers/built-in.o: In function `altera_tse_probe':
altera_tse_main.c:(.text+0x25ec2e): undefined reference to `dma_set_mask'
altera_tse_main.c:(.text+0x25ec78): undefined reference to `dma_supported'
altera_tse_main.c:(.text+0x25ecb6): undefined reference to `dma_supported'
drivers/built-in.o: In function `sgdma_async_read':
altera_sgdma.c:(.text+0x25f620): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f678): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f696): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f6f0): undefined reference to `dma_map_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f702): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `sgdma_tx_buffer':
(.text+0x25f92a): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_rx_status':
(.text+0x25fa24): undefined reference to `dma_sync_single_for_cpu'
make[3]: *** [vmlinux] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-05-01
Please pull the following batch of fixes intended for the 3.15 stream!
For the Bluetooth bits, Gustavo says:
"Some fixes for 3.15. There is a revert for the intel driver, a new
device id, and two important SSP fixes from Johan."
On top of that...
Ben Hutchings gives us a fix for an unbalanced irq enable in an
rtl8192cu error path.
Colin Ian King provides an rtlwifi fix for an uninitialized variable.
Felix Fietkau brings a pair of ath9k fixes, one that corrects a
hardware initialization value and another that removes an (unnecessary)
flag that was being used in a way that led to a software tx queue
hang in ath9k.
Gertjan van Wingerde pushes a MAINTAINERS change to remove himself
from the rt2x00 maintainer team.
Hans de Goede fixes a brcmfmac firmware load hang.
Larry Finger changes rtlwifi to use the correct queue for V0 traffic
on rtl8192se.
Rajkumar Manoharan corrects a race in ath9k driver initialization.
Stanislaw Gruszka fixes an rt2x00 bug in which disabling beaconing
once on USB devices led to permanently disabling beaconing for those
devices.
Tim Harvey provides fixes for a pair of ath9k issues that can lead
to soft lockups in that driver.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following commit:
commit 9ec36cafe43bf835f8f29273597a5b0cbc8267ef
Author: Rob Herring <robh@kernel.org>
Date: Wed Apr 23 17:57:41 2014 -0500
of/irq: do irq resolution in platform_get_irq
changed platform_get_irq() which now returns EINVAL and EPROBE_DEFER,
in addition to ENXIO. If there's no interrupt for mvmdio, platform_get_irq()
returns EINVAL, but we currently check only for ENXIO.
Fix this by looking for a positive integer, which is the proper way of
validating a virtual interrupt number.
While at it, add a proper handling for the deferral probe case.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_state_machine should check whether auto-negotiatin is completed
before changing phydev->state from PHY_NOLINK to PHY_RUNNING. If
auto-negotiation is not completed phydev->state should be set to
PHY_AN.
Signed-off-by: Balakumaran Kannan <kumaran.4353@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Do checksum offload only if the client of the driver wants checksum to be
offloaded.
In V1 version of this patch, I addressed comments from
Stephen Hemminger <stephen@networkplumber.org> and
Eric Dumazet <eric.dumazet@gmail.com>.
In this version of the patch I have addressed comments from
David Miller.
This patch fixes a bug that is exposed in gateway scenarios.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For phy devices that don't issue interrupts upon link
state changes, phylib polls the link state resulting in
repeated calls to adjust_link(), even if the link state
didn't change. As a result, some mac registers are
repeatedly read and written with the same values, which
is not ok.
To fix this, adjust_link() has been refactored to check
first whether the link state has changed and to take action
only if needed, updating mac registers and local state
variables. The 'new_state' local flag, set if one of the
link params changed (link, speed or duplex), has been
rendered useless and removed by this refactoring.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 12a2856b604476c27d85a5f9a57ae1661fc46019.
The commit above doesn't appear to be necessary any more as the
checksums appear to be correctly computed/validated.
Additionally the above commit breaks kvm configurations where
one VM is using a device that support checksum offload (virtio) and
the other VM does not.
In this case, packets leaving virtio device will have CHECKSUM_PARTIAL
set. The packets is forwarded to a macvtap that has offload features
turned off. Since we use CHECKSUM_UNNECESSARY, the host does does not
update the checksum and thus a bad checksum is passed up to
the guest.
CC: Daniel Lezcano <daniel.lezcano@free.fr>
CC: Patrick McHardy <kaber@trash.net>
CC: Andrian Nord <nightnord@gmail.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following is a problematic configuration:
VM1: virtio-net device connected to macvtap0@eth0
VM2: e1000 device connect to macvtap1@eth0
The problem is is that virtio-net supports checksum offloading
and thus sends the packets to the host with CHECKSUM_PARTIAL set.
On the other hand, e1000 does not support any acceleration.
For small TCP packets (and this includes the 3-way handshake),
e1000 ends up receiving packets that only have a partial checksum
set. This causes TCP to fail checksum validation and to drop
packets. As a result tcp connections can not be established.
Commit 3e4f8b787370978733ca6cae452720a4f0c296b8
macvtap: Perform GSO on forwarding path.
fixes this issue for large packets wthat will end up undergoing GSO.
This commit adds a check for the non-GSO case and attempts to
compute the checksum for partially checksummed packets in the
non-GSO case.
CC: Daniel Lezcano <daniel.lezcano@free.fr>
CC: Patrick McHardy <kaber@trash.net>
CC: Andrian Nord <nightnord@gmail.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds set_rx_int_on_com function for interrupt when
dma is completed.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds rxqueue enable function according to number of rxqueue
and adds rxqueue disable function for removing.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves sw reset to probe function because
sw reset is needed early stage before open function.
Signed-off-by: Byungho An <bh74.an@samsung.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add handling for " 8 GT/s" in print_port_info().
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes the following sparse warnings:
drivers/net/ethernet/altera/altera_msgdma.c:23:5: warning: symbol 'msgdma_initialize' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:28:6: warning: symbol 'msgdma_uninitialize' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:32:6: warning: symbol 'msgdma_reset' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:77:6: warning: symbol 'msgdma_disable_rxirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:83:6: warning: symbol 'msgdma_enable_rxirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:89:6: warning: symbol 'msgdma_disable_txirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:95:6: warning: symbol 'msgdma_enable_txirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:101:6: warning: symbol 'msgdma_clear_rxirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:107:6: warning: symbol 'msgdma_clear_txirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:114:5: warning: symbol 'msgdma_tx_buffer' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:129:5: warning: symbol 'msgdma_tx_completions' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:154:5: warning: symbol 'msgdma_add_rx_desc' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:181:5: warning: symbol 'msgdma_rx_status' was not declared. Should it be static?
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sgdma_descrip is a function name as well as the name of a struct. In
sgdma_initialize(), we should initialize the descriptor length field
with the actual length of a descriptor not with the size of the
function. In order to prevent such things from happening in the future,
rename the function to sgdma_setup_descrip().
Found by sparse which yields the following warning:
drivers/net/ethernet/altera/altera_sgdma.c:74:30: warning: expression using sizeof on a function
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: a53268be0cb9 ('rtlwifi: rtl8192cu: Fix too long disable of IRQs')
Cc: stable@vger.kernel.org
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Beginning with kernel 3.13, this driver fails on some systems. The problem
was bisected to:
Commit 1bf4bbb4024dcdab5e57634dd8ae1072d42a53ac
Author: Felix Fietkau <nbd@openwrt.org>
Title: mac80211: send control port protocol frames to the VO queue
There is noting wrong with the above commit. The regression occurs because
V0 queue on RTL8192SE cards uses priority 6, not the usual 7. The fix is to
modify the rtl8192se routine that sets the correct transmit queue.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=74541
Reported-by: Alex Miller <almiller_1@yahoo.co.uk>
Tested-by: Alex Miller <almiller_1@yahoo.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.13+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There are some corner cases where the driver could get stuck with a full
tid queue that is paused, leading to a software tx queue hang.
Since the tx queueing rework, pausing per-tid queues on aggregation
session setup is no longer necessary. The driver will assign sequence
numbers to buffered frames when a new session is established, in order
to get the correct starting sequence number.
mac80211 prevents new frames from entering the queue during setup.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When the amount of noise fluctuates strongly, low immunity settings
can sometimes disrupt signal detection on AR913x chips. When that
happens, no OFDM/CCK errors are reported anymore, and ANI tunes the
radio to the lowest immunity settings.
Usually rx/tx fails as well in that case.
To fix this, keep noise immunity settings at or above ANI default level,
which will keep radio parameters at or above INI values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Fix format string mismatch in bonding_show_min_links().
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With commit cc9fa74e2a ("slip/slcan: added locking in wakeup function") a
formerly missing locking was added to slip.c and slcan.c by Andre Naujoks.
Alexander Stein contributed the fix 367525c8c2 ("can: slcan: Fix spinlock
variant") as the kernel lock debugging advised to use spin_lock_bh() instead
of just using spin_lock().
This fix has to be applied to the same code section in slip.c for the same
reason too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dan writes:
"The Dell drivers use the same configuration for PIDs:
81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card
81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card
81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card
81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card
81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card
These devices are all clearly Sierra devices, but are also definitely
Gobi-based. The A8 might be the MC7700/7710 and A9 is likely a MC7750.
>From DellGobi5kSetup.exe from the Dell drivers:
usbif0: serial/firmware loader?
usbif2: nmea
usbif3: modem/ppp
usbif8: net/QMI"
Reported-by: AceLan Kao <acelan.kao@canonical.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A number of older CMOTech modems are based on Qualcomm
chips and exporting a QMI/wwan function.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Device interface layout:
0: ff/ff/ff - serial
1: ff/00/00 - serial AT+PPP
2: ff/ff/ff - QMI/wwan
3: 08/06/50 - storage
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Device interface layout:
0: ff/ff/ff - serial
1: ff/ff/ff - serial AT+PPP
2: 08/06/50 - storage
3: ff/ff/ff - serial
4: ff/ff/ff - QMI/wwan
Reported-by: Julio Araujo <julio.araujo@wllctel.com.br>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds ability for the arc_emac to really handle its supplying clock.
To get the needed clock-frequency either a real clock or the previous
clock-frequency property must be provided.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The probe function at the moment only frees the netdev but does not disconnect
the phy or removes the mdio bus it registered.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the PTP Tx timestamp interrupt handler. The original
code misinterpreted the interrupt handler design. We were clearing the
ena_mask bit for the Timesync interrupts. This is done to indicate that
the interrupt will be handled in a scheduled work item (instead of
immediately) and that work item is responsible for re-enabling the
interrupts. However, the Tx timestamp was being handled immediately and
nothing was ever re-enabling it. This resulted in a single interrupt
working for the life of the driver.
This patch fixes the issue by instead clearing the bit from icr0 which
is used to indicate that the interrupt was immediately handled and can
be re-enabled right away. This patch also clears up a related issue due
to writing the PRTTSYN_STAT_0 register, which was unintentionally
clearing the cause bits for Timesync interrupts.
Change-ID: I057bd70d53c302f60fab78246989cbdfa469d83b
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
this is a pull request for net/master, for the v3.15 release cycle, consisting
of 26 patches.
Thomas Gleixner contributes 21 patches for the c_can driver, which address
several shortcomings in the driver like hardware initialisation, concurrency,
message ordering and poor performance. Two patches Oliver Hartkopp, one adds a
missing lock to the sja1000_isa driver, the other one fixes the return value in
the generic bit time configuration function. And finally a patch by Alexander
Stein, that fixes the slcan driver to use the correct spinlock variant.
To make it 26 patches, Wolfgang Grandegger patch for the c_can_pci
driver, which enables the bus master only for MSI and a patch by
Wolfram Sang, which converts the 'instance' in the c_can driver to the
proper type.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes the name used by Ethtool to something more
conventional in preparation for TSE Ethtool register dump
support to be added in the near future.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch addresses a fault in the error recovery path of the probe
routine where the netdev structure was not being unregistered properly
leading to a panic only when the phy probe failed.
Abbreviated panic stack seen is as follows:
(free_netdev+0xXX) from (altera_tse_probe+0xXX)
(altera_tse_probe+0xXX) from (platform_drv_probe+0xXX)
(platform_drv_probe+0xXX) from (driver_probe_device+0xXX)
(driver_probe_device+0xXX) from (__driver_attach+0xXX)
(__driver_attach+0xXX) from (bus_for_each_dev+0xXX)
(bus_for_each_dev+0xXX) from (driver_attach+0xXX)
(driver_attach+0xXX) from (bus_add_driver+0xXX)
(bus_add_driver+0xXX) from (driver_register+0xXX)
(driver_register+0xXX) from (__platform_driver_register+0xXX)
(__platform_driver_register+0xXX) from (altera_tse_driver_init+0xXX)
(altera_tse_driver_init+0xXX) from (do_one_initcall+0xXX)
(do_one_initcall+0xXX) from (kernel_init_freeable+0xXX)
(kernel_init_freeable+0xXX) from (kernel_init+0xXX)
(kernel_init+0xXX) from (ret_from_fork+0xXX)
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
