| Age | Commit message (Collapse) | Author |
|---|
|
We need linux/pci.h.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Use local-mac-address in the device tree instead. Fall back to mac-address
for older firmware.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
PHY support for pasemi_mac.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add msglevel support for pasemi_mac. Move the MODULE_* defines to the
top to go together with the variable (similar to tg3).
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Logic cleanup and some performance enhancements to the RX path.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* Remove some unused defines
* Fix a couple of wrong chip register defines, and add a few more fields
that might be used in the near future.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add a copy-break and recycle the SKB in the driver for small packets.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Timer and interrupt fixes:
* Be pickier with what kind of interrupts are acked to avoid the device to
get out of sync with the driver state
* Set RX count threshhold to 1 (for NAPI interrupted mode), TX count
threshold to 32.
* Set timer thresholds to current max (~16ms).
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Abstract out (and fix up) the interrupt restart routines, making
sure we start out in a consistent state.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fixes for ethernet IRQ mapping, to be done in the driver instead of in
the platform setup code.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Apply changes in commit 4c13eb6657fe9ef7b4dc8f1a405c902e9e5234e0 to
newly added piece of code.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Convert to generic boolean.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The order that the two 32-bit words written to the Hash Address (Low,
High) Registers for matching of multicast addresses is incorrect.
Signed-off-by: Lars Reemts <Lars.Reemts@entwicklung.eq-3.de>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add support for a number of new PHY's in the AT91RM9200 Ethernet driver.
- Teridian 78Q21x3
- SMSC LAN83C185
(Patch from Luca Gamma)
- National Semiconductor DP83848
(Patches from Ivan Kuten & Thomas Foldesi)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Dear Jeff
Subject: [PATCH] xirc2ps_cs: bugfix of multicast code
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This fixes the regression in 2.6.21 for users with 88e8056 on motherboard.
Allow all but the Gigabyte motherboard has some unresolved bus problems.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch lets RBTX49XX boards use generic platform_driver interface
for the ne driver.
* Use platform_device to pass ioaddr and irq to the ne driver.
* Remove unnecessary ifdefs for RBTX49XX from the ne driver.
* Make the ne driver selectable on these boards regardless of CONFIG_ISA
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add NEEDS_PORTLIST cpp macro to control ISA auto-probe.
(I'm not sure M32R needs auto-probe but it is current behavior)
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Miscellaneous fixes to make ne platform driver work properly.
* Make ioaddr 'unsigned long'.
* Move a printk down to show dev->name assigned in register_netdev.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add a platform_driver interface to ne driver.
(Existing legacy ports did not covered by this ne_driver for now)
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Need to change the libertas Kconfig entry to match changes made for
other wireless drivers.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Remove trailing whitespace and spaces preceding tabs.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Use dev_printk macros for PCI related errors, warnings, debug and info
console messages.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Adapt to new skb header access functions.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The natsemi driver contains a workaround for broken hardware which can
partially reset the chip at unpredictable times, detected by checking for
spontaneous changes in the DspCfg register. The effects of the hardware
bug appear to be variable and can range from minor problems like small
numbers of corrupted packets to major ones such as the chip becoming
non-functional. In the case of minor problems the chip reconfiguration
required to work around the hardware can cause more problems than the bug
itself.
Since we have no way of automatically determining how badly the problem
manifests on any given system provide an option in sysfs allowing users to
disable the workaround at runtime and provides a module option to set the
default.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The natsemi driver has a workaround for broken hardware which resets itself
from time to time. There is a diagnostic message for this workaround but
it is not printed by default, making the driver behavior more obscure than
it needs to be. Make the message be displayed by default.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch supports SuperH of smc91x.
smc91x installed on the board of SuperH comes to work by applying this patch.
Please apply this patch .
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The DM9000 network driver is calling kfree() on an netdev
causing the system to oops if the probe fails. The right
thing to do is call free_netdev().
Thanks to Russell King for spotting this.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Wake On Lan works correctly on Yukon-FE and other variants.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>a
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Remove the aligned-completion whitelist, and replace it by using the 1.4.16
firmware's auto-detection features to choose which firmware to load.
The driver now loads the aligned firmware, performs a MXGEFW_CMD_UNALIGNED_TEST,
and falls back to using the unaligned firmware if:
- The firmware is too old (ie, MXGEFW_CMD_UNALIGNED_TEST is an unknown command).
- The MXGEFW_CMD_UNALIGNED_TEST returns MXGEFW_CMD_ERROR_UNALIGNED, meaning
that it has seen an unaligned completion during the DMA test.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Move the DMA test code into its own function.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Don't count on whatever implementation artifact preserves the
multicast list across a reset cmd, and setup multicast filtering
as part of our reset routine.
The setting of allmulti when adopting firmware with the rx-filter
broadcast bug is also moved into the multicast setup routine where
it belongs.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Update myri10ge firmware headers to those of 1.4.16.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add dropped_pause, dropped_bad_phy, dropped_bad_crc32,
dropped_unicast_filtered to the set of ethtool counters.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Bugfixes:
* Move the wake_queue logic from tx_intr to clean_tx
* Always do wake_queue even if queue wasn't full before clean since
it's safe to do
* Fix polarity in checks in pasemi_mac_close
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: rfkill: add support for input key to control wireless radio
[NET] net/core: Fix error handling
[TG3]: Update version and reldate.
[TG3]: Eliminate spurious interrupts.
[TG3]: Add ASPM workaround.
[Bluetooth] Correct SCO buffer for another Broadcom based dongle
[Bluetooth] Add support for Targus ACB10US USB dongle
[Bluetooth] Disconnect L2CAP connection after last RFCOMM DLC
[Bluetooth] Check that device is in rfcomm_dev_list before deleting
[Bluetooth] Use in-kernel sockets API
[Bluetooth] Attach host adapters to the Bluetooth bus
[Bluetooth] Fix L2CAP and HCI setsockopt() information leaks
|
|
master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Convert to NAPI
IB: Return "maybe missed event" hint from ib_req_notify_cq()
IB: Add CQ comp_vector support
IB/ipath: Fix a race condition when generating ACKs
IB/ipath: Fix two more spin lock problems
IB/fmr_pool: Add prefix to all printks
IB/srp: Set proc_name
IB/srp: Add orig_dgid sysfs attribute to scsi_host
IPoIB/cm: Don't crash if remote side uses one QP for both directions
RDMA/cxgb3: Support for new abort logic
RDMA/cxgb3: Initialize cpu_idx field in cpl_close_listserv_req message
RDMA/cxgb3: Fail qp creation if the requested max_inline is too large
RDMA/cxgb3: Fix TERM codes
IPoIB/cm: Fix error handling in ipoib_cm_dev_open()
IB/ipath: Don't corrupt pending mmap list when unmapped objects are freed
IB/mthca: Work around kernel QP starvation
IB/ipath: Don't put QP in timeout queue if waiting to send
IB/ipath: Don't call spin_lock_irq() from interrupt context
|
|
As SMC91X ethernet controller are used in blackfin STAMP 533 development
board, this patch add blackfin support to the smc91x linux driver.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update version to 3.76.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spurious interrupts are often encountered especially on systems
using the 8259 PIC mode. This is because the I/O write to deassert
the interrupt is posted and won't get to the chip immediately. As
a result, the IRQ may remain asserted after the IRQ handler exits,
causing spurious interrupts.
Flush the interrupt mailbox in non-MSI handlers to de-assert the
IRQ immediately. This seems to be the most straight forward approach
after discussion with Jeff Garzik and David Miller.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds workaround to fix performance problems caused by slow
PCIE L1->L0 transitions on ICH8 platforms.
Changed all magic numbers to constants as suggested by Jeff Garzik.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HW now posts 2 ABORT_RPL and/or PEER_ABORT_REQ messages. We need
to handle them by silenty dropping the 1st but mark that we're ready
for the final message. This plugs some close races between the uP and
HW. Also update the minimum required firmware version.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (38 commits)
kconfig: fix mconf segmentation fault
kbuild: enable use of code from a different dir
kconfig: error out if recursive dependencies are found
kbuild: scripts/basic/fixdep segfault on pathological string-o-death
kconfig: correct minor typo in Kconfig warning message.
kconfig: fix path to modules.txt in Kconfig help
usr/Kconfig: fix typo
kernel-doc: alphabetically-sorted entries in index.html of 'htmldocs'
kbuild: be more explicit on missing .config file
kbuild: clarify the creation of the LOCALVERSION_AUTO string.
kbuild: propagate errors from find in scripts/gen_initramfs_list.sh
kconfig: refer to qt3 if we cannot find qt libraries
kbuild: handle compressed cpio initramfs-es
kbuild: ignore section mismatch warning for references from .paravirtprobe to .init.text
kbuild: remove stale comment in modpost.c
kbuild/mkuboot.sh: allow spaces in CROSS_COMPILE
kbuild: fix make mrproper for Documentation/DocBook/man
kbuild: remove kconfig binaries during make mrproper
kconfig/menuconfig: do not hardcode '.config'
kbuild: override build timestamp & version
...
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (82 commits)
[ARM] Add comments marking in-use ptrace numbers
[ARM] Move syscall saving out of the way of utrace
[ARM] 4360/1: S3C24XX: regs-udc.h remove unused macro
[ARM] 4358/1: S3C24XX: mach-qt2410.c: remove linux/mmc/protocol.h header
[ARM] mm 10: allow memory type to be specified with ioremap
[ARM] mm 9: add additional device memory types
[ARM] mm 8: define mem_types table L1 bit 4 to be for ARMv6
[ARM] iop: add missing parens in macro
[ARM] mm 7: remove duplicated __ioremap() prototypes
ARM: OMAP: fix OMAP1 mpuio suspend/resume oops
ARM: OMAP: MPUIO wake updates
ARM: OMAP: speed up gpio irq handling
ARM: OMAP: plat-omap changes for 2430 SDP
ARM: OMAP: gpio object shrinkage, cleanup
ARM: OMAP: /sys/kernel/debug/omap_gpio
ARM: OMAP: Implement workaround for GPIO wakeup bug in OMAP2420 silicon
ARM: OMAP: Enable 24xx GPIO autoidling
[ARM] 4318/2: DSM-G600 Board Support
[ARM] 4227/1: minor head.S fixups
[ARM] 4328/1: Move i.MX UART regs to driver
...
|
|
And fix up the code to always allow MSI on 5714 A2.
Call tg3_find_peer() earlier because we need that information before
we can determine whether we can set TG3_FLAG_SUPPORT_MSI or not.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the use of the TG3_FLAG_5701_REG_WRITE_BUG flag.
It's logic is only used to set a function pointer and thus the
logic can be collapsed and the flag removed.
[ Comment tidy by Christoph Hellwig. -DaveM ]
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
|
|
This flag does not do anything useful.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reset was added a while back so that ASF could re-init whatever
MAC address it wanted to use after the MAC address was changed.
Instead of resetting, we can just keep MAC address 1 unchanged during
MAC address changes if MAC address 1 is different from MAC address 0.
This fixes 2 problems:
1. Bonding calls set_mac_address in contexts that cannot sleep.
It no longer sleeps with the chip reset removed.
2. When ASF shares the same MAC address as the NIC, it needs to
always do that even when the MAC address is changed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change TG3_FLAG_SERDES_WOL_CAP to TG3_FLAG_WOL_CAP to make it easier
to manage WoL. This flag is now used consistently during ethtool WoL
setup and power setting changes.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The GPIO settings may change during reset and so the stored values in
tp->grc_local_ctrl should be cleared first.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
