| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-08-18
This series contains updates to ixgbe and ixgbevf.
Emil cleans up confusing amongst the users by making an error message
into a debug message, since the TXDCTL.ENABLE (and comparable
VFTXDCTL.ENABLE for ixgbevf) bit is set only when the
transmit queue is actually enabled, which may not happen during the
configure phase eve if we waited for it. Converts to using netdev_dbg()
macro instead of our home brewed macro for ixgbevf. Converted the
service task to use atomic bitwise operations when setting and checking
reset requests to reduce the possibility of race conditions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove our dsa_switch_driver::drv_probe callback to prevent probing
through the old DSA binding, not that this could happen anymore now that
we have moved the matching compatible string from net/dsa/dsa.c to
drivers/net/dsa/bcm_sf2.c, so this is essentially dead code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have converted the drivers into a proper platform device
driver, we can use the device managed helper functions to simplify the
error paths a bit wrt. register resources and IRQs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Broadcom Starfighter 2 switch driver should be a proper platform
driver, now that the DSA code has been updated to allow that, register a
switch device, feed it with the proper configuration data coming from
Device Tree and register our switch device with DSA.
The bulk of the changes consist in moving what bcm_sf2_sw_setup() did
into the platform driver probe function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When mv88e6xxx_wait() returns a timeout, something bad has
happened. Make sure it is noticed by logging an error.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that mv88e6xx_wait() iterated on a counter than a fixed time
interval, it implements the same mechanism as mv88e6xxx_update() uses.
So use it in mv88e6xx_wait().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6xxx driver times out operations on the switch based on
looping until an elapsed wall clock time is reached. However, if
usleep_range() sleeps much longer than expected, it could timeout with
an error without actually checking to see if the devices has completed
the operation. So replace the elapsed time with a fixed upper bound on
the number of loops.
Testing on various switches has shown that switches takes either 0 or
1 iteration, so a maximum of 16 iterations is a safe limit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the redundant "Support for" and "Drivers for" from the Kconfig
short description. This makes the manufacture much more prominent in
the list and makes the shortcut keys useful.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sort the files to reduce merge conflicts and to make it easier to find
drivers by name. Also separate the MDIO bus drivers from the PHY
drivers, again to help find what you need.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An upcoming feature of IBM VNIC protocol is the ability to configure
redundant backing devices for a VNIC client. In case of a failure
on the current backing device, the driver will receive a signal
from the hypervisor indicating that a failover will occur. The driver
will then wait for a message from the backing device before
establishing a new connection.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It added reset function for RoCE driver. RoCE is a feature of hns.
In hip06 SoC, in RoCE reset process, it's needed to configure dsaf
channel reset, port and sl map info. Reset function of RoCE is
located in dsaf module, we only call it in RoCE driver when needed.
This patch is used to fix the conflict, please refer to this link:
https://www.spinics.net/lists/linux-rdma/msg39114.html
Signed-off-by: Wei Hu <xavier.huwei@huawei.com>
Signed-off-by: Nenglong Zhao <zhaonenglong@hisilicon.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Sheng Li <lisheng011@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new commmon infrastructure to allocate reosurces dynamically to
Upper layer driver's(ULD) when they register with cxgb4 driver and free
them during unregistering. All the queues and the interrupts for
them will be allocated during ULD probe only and freed during remove.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It doesn't really change anything as BGMAC_CHIPCTL_1_IF_TYPE_RMII is
equal to 0. It make code a bit clener, so far when reading it one could
think we forgot to set a proper mode. It also keeps this mode code in
sync with other ones.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BCM53573 is a new series of Broadcom's SoCs. It's based on ARM and can
be found in two packages (versions): BCM53573 and BCM47189. It shares
some code with the Northstar family, but also requires some new quirks.
First of all there can be up to 2 Ethernet cores on this SoC. If that is
the case, they are connected to two different switch ports allowing some
more complex/optimized setups. It seems the second unit doesn't come
fully configured and requires some IRQ quirk.
Other than that only the first core is connected to the PHY. For the
second one we have to register fixed PHY (similarly to the Northstar),
otherwise generic PHY driver would get some invalid info.
This has been successfully tested on Tenda AC9 (BCM47189B0).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is useful to be able to see the hash configuration when running tests.
This patch adds a debugfs node for that purpose.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The division is already being done properly in efx_ef10_get_timer_config
which returns zero-on-success, unlike the old efx_ef10_get_sysclk_freq.
Fixes: d95e329a55ba ("sfc: get timer configuration from adapter")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While '0xdead' and '0xbeef' are "great" values, we should
use the correct SPEED_* values instead.
Fixes: 054c67d1c82a ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When moving into using ethtool's link_ksetting, qed started
supplying its own bitmask of speed/capabilities, but qede
is still checking for the SUPPORTED value to determine whether
it supports pause.
Fixes: 054c67d1c82a ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use atomic bitwise operations when setting and checking reset
requests. This should help with possible races in the service task.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Following a write the VFTXDCTL.ENABLE bit is set only when the Tx queue
is actually enabled, which may not happen during the configure phase even
if we waited for it. Make this check debug only since this is causing
confusion with users who notice the warning in dmesg.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Instead of the home brewed macro make use of netdev_dbg same as
the ixgbe driver.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Following a write the TXDCTL.ENABLE bit is set only when the Tx queue
is actually enabled, which may not happen during the configure phase even
if we waited for it. Make this check debug only since this is causing
confusion with users who notice the warning in dmesg.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use error "rmgr: Cannot insert RX class rule: Operation not supported" is
more meaningful than "rmgr: Cannot insert RX class rule: Unknown error 524"
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is meant to allow for RX network flow classification to insert
and remove VLAN priority filter by ethtool
Example:
Add an VLAN priority filter:
$ ethtool -N eth0 flow-type ether vlan 0x6000 vlan-mask 0x1FFF action 2 loc 1
Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 1 rules
Filter: 1
Flow Type: Raw Ethernet
Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
Ethertype: 0x0 mask: 0xFFFF
VLAN EtherType: 0x0 mask: 0xffff
VLAN: 0x6000 mask: 0x1fff
User-defined: 0x0 mask: 0xffffffffffffffff
Action: Direct to queue 2
Delete the filter by location:
$ ethtool -N delete 1
Signed-off-by: Ruhao Gao <ruhao.gao@ni.com>
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is meant to allow for RX network flow classification to insert
and remove ethertype filter by ethtool
Example:
Add an ethertype filter:
$ ethtool -N eth0 flow-type ether proto 0x88F8 action 2
Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 1 rules
Filter: 15
Flow Type: Raw Ethernet
Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
Ethertype: 0x88F8 mask: 0x0
Action: Direct to queue 2
Delete the filter by location:
$ ethtool -N delete 15
Signed-off-by: Ruhao Gao <ruhao.gao@ni.com>
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is meant to allow for RX network flow classification to insert
and remove Rx filter by ethtool. Ethtool interface has it's own rules
manager
Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 2 rules
Signed-off-by: Ruhao Gao <ruhao.gao@ni.com>
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The patch adds driver support for sending the NCSI statistics to the
MFW. This is an asynchronous request from MFW. Upon receiving this, driver
populates the required data and send it to MFW.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch adds driver support for capturing stats ttl0_discard and
packet_too_big_discard in "ethtool -S" display.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For implementing this driver most of the inputs is
provided by Andrew Lunn.
Updating the driver with Andrew Copy right.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the platforms like zynqmp ultrascale+ has a
separate clock gate for the rx clock. Add an optional
rx_clk so that the clock can be enabled.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This enables
ip -d l
to indicate if trust is on or off for VFs.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We shifted the locking around a bit but forgot to delete this unlock so
now it can unlock twice.
Fixes: cd3be169a5ff ('i40e: Move the mutex lock in i40e_client_unregister')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bimmy Pujari <Bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch implements a feature change which allows using ethtool to set
RSS hash opts using less than four parameters if desired.
Change-ID: I0fbb91255d81e997c456697c21ac39cc9754821b
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When we allocate memory, we must free it. It's simple courtesy.
Change-ID: Id007294096fb53344f1a8b9a0f78eddf9853c5d6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes the bug which causes RSS to continue to work
after being disabled. After disabling RSS, traffic would continue
to be assigned to different queues instead of falling back to a
single queue. Without this patch, attempting to disable RSS would
not work as expected. This patch fixes the bug by clearing the
lookup table used by RSS such that all traffic is assigned to a
single queue. This patch also addresses the issue of reinstating
the lookup table should RSS then be re-enabled.
Change-ID: Ib20c7c6a7e9f1f772bb787370f8a8c664796b141
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
VF goes through reset path during VF creation which happens to also
have notification of VF reset to client. Adding conditional check to
avoid wrongly notifying VF reset during VF creation.
Also changing the call order of VF enable, calling it after VF creation
rather than before.
Change-ID: I96eabd99deae746a2f0fc465194c886f196178ce
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is a fix for the bug i.e. unable to create iwarp device
in VF. This is a sync issue and the iwarp device open is called even
before the PCI register writes are done.
Forcing the PCI register writes to happen just before it exits the
function.
Change-ID: I60c6a2c709da89e845f2764cc50ce8b7373c8c44
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If a driver is unable to maintain all current user supplied settings
from ethtool (or other sources), it is not ok for a user request to
succeed and silently trample over previous configuration.
To that end, if you change the number of channels, it must not be
allowed to reduce the number of channels (queues) below the current
flow director filter rules targets. In this case, return -EINVAL when
a request to reduce the number of channels would do so. In addition
log a warning to the kernel buffer explaining why we failed, and report
the rules which prevent us from lowering the number of channels.
Change-ID: If41464d63d7aab11cedf09e4f3aa1a69e21ffd88
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes a problem where a static analysis tool generates
a warning for "INVARIANT_CONDITION: Expression 'enabled_tc' used
in the condition always yields the same result."
Without this patch, the driver will not pass the static analysis
tool checks without generating warnings.
This patch fixes the problem by eliminating the irrelevant check
and redundant assignment for the value of enabled_tc.
Change-ID: Ia7d44cb050f507df7de333e96369d322e08bf408
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The function calls netif_set_real_num_(tx|rx)_queues, both of which
should be done only under rntl lock. Unfortunately the
i40evf_init_task did not hold the rtnl_lock as necessary. This patch
adds the locking needed.
Change-ID: Ib72a21c3ce22b71a226b16f9bbe0f5f8cc3e849b
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When we are resetting the pf stats we should also reset the RX csum
error stat.
Change-ID: I7af5ee0ec81a10f6deee1a7b8c2082ea068ef620
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When we do a reset, all the VLAN filters get added again. Therefore we also
want to reset the VLAN count to 0 or we quickly run out of filters.
Change-ID: I459f26851e22204dc8b8999928ad87cde8170119
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The client->open call in this path was not protected with the
client instance mutex, and hence the client->close can get initiated
before the open completes.
Change-Id: I0ed60c38868dd3f44966b6ed49a063d0e5b7edf5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Using list_move() instead of list_del() + list_add().
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Buffers powersave frame test is reversed in cfg80211, fix from Felix
Fietkau.
2) Remove bogus WARN_ON in openvswitch, from Jarno Rajahalme.
3) Fix some tg3 ethtool logic bugs, and one that would cause no
interrupts to be generated when rx-coalescing is set to 0. From
Satish Baddipadige and Siva Reddy Kallam.
4) QLCNIC mailbox corruption and napi budget handling fix from Manish
Chopra.
5) Fix fib_trie logic when walking the trie during /proc/net/route
output than can access a stale node pointer. From David Forster.
6) Several sctp_diag fixes from Phil Sutter.
7) PAUSE frame handling fixes in mlxsw driver from Ido Schimmel.
8) Checksum fixup fixes in bpf from Daniel Borkmann.
9) Memork leaks in nfnetlink, from Liping Zhang.
10) Use after free in rxrpc, from David Howells.
11) Use after free in new skb_array code of macvtap driver, from Jason
Wang.
12) Calipso resource leak, from Colin Ian King.
13) mediatek bug fixes (missing stats sync init, etc.) from Sean Wang.
14) Fix bpf non-linear packet write helpers, from Daniel Borkmann.
15) Fix lockdep splats in macsec, from Sabrina Dubroca.
16) hv_netvsc bug fixes from Vitaly Kuznetsov, mostly to do with VF
handling.
17) Various tc-action bug fixes, from CONG Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net_sched: allow flushing tc police actions
net_sched: unify the init logic for act_police
net_sched: convert tcf_exts from list to pointer array
net_sched: move tc offload macros to pkt_cls.h
net_sched: fix a typo in tc_for_each_action()
net_sched: remove an unnecessary list_del()
net_sched: remove the leftover cleanup_a()
mlxsw: spectrum: Allow packets to be trapped from any PG
mlxsw: spectrum: Unmap 802.1Q FID before destroying it
mlxsw: spectrum: Add missing rollbacks in error path
mlxsw: reg: Fix missing op field fill-up
mlxsw: spectrum: Trap loop-backed packets
mlxsw: spectrum: Add missing packet traps
mlxsw: spectrum: Mark port as active before registering it
mlxsw: spectrum: Create PVID vPort before registering netdevice
mlxsw: spectrum: Remove redundant errors from the code
mlxsw: spectrum: Don't return upon error in removal path
i40e: check for and deal with non-contiguous TCs
ixgbe: Re-enable ability to toggle VLAN filtering
ixgbe: Force VLNCTRL.VFE to be set in all VMDq paths
...
|
