| Age | Commit message (Collapse) | Author |
|---|
|
To be consistent with other namespaces, expose a 'size' attribute for
BTT devices also.
Cc: Dan Williams <dan.j.williams@intel.com>
Reported-by: Linda Knippers <linda.knippers@hpe.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Since commit 63a4cc24867d, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Commit abf545484d31 changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.
Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The rw_page users were not converted to use bio/req ops. As a result
bdev_write_page is not passing down REQ_OP_WRITE and the IOs will
be sent down as reads.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixes: 4e1b2d52a80d ("block, fs, drivers: remove REQ_OP compat defs and related code")
Modified by me to:
1) Drop op_flags passing into ->rw_page(), as we don't use it.
2) Make op_is_write() and friends safe to use for !CONFIG_BLOCK
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
- Replace pcommit with ADR / directed-flushing.
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement
either ADR, or provide one or more flush addresses per nvdimm.
ADR (Asynchronous DRAM Refresh) flushes data in posted write buffers
to the memory controller on a power-fail event.
Flush addresses are defined in ACPI 6.x as an NVDIMM Firmware
Interface Table (NFIT) sub-structure: "Flush Hint Address Structure".
A flush hint is an mmio address that when written and fenced assures
that all previous posted writes targeting a given dimm have been
flushed to media.
- On-demand ARS (address range scrub).
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the
media to refresh the bad block list, userspace can also request a
re-scrub at any time.
- Support for the Microsoft DSM (device specific method) command
format.
- Support for EDK2/OVMF virtual disk device memory ranges.
- Various fixes and cleanups across the subsystem.
* tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (41 commits)
libnvdimm-btt: Delete an unnecessary check before the function call "__nd_device_register"
nfit: do an ARS scrub on hitting a latent media error
nfit: move to nfit/ sub-directory
nfit, libnvdimm: allow an ARS scrub to be triggered on demand
libnvdimm: register nvdimm_bus devices with an nd_bus driver
pmem: clarify a debug print in pmem_clear_poison
x86/insn: remove pcommit
Revert "KVM: x86: add pcommit support"
nfit, tools/testing/nvdimm/: unify shutdown paths
libnvdimm: move ->module to struct nvdimm_bus_descriptor
nfit: cleanup acpi_nfit_init calling convention
nfit: fix _FIT evaluation memory leak + use after free
tools/testing/nvdimm: add manufacturing_{date|location} dimm properties
tools/testing/nvdimm: add virtual ramdisk range
acpi, nfit: treat virtual ramdisk SPA as pmem region
pmem: kill __pmem address space
pmem: kill wmb_pmem()
libnvdimm, pmem: use nvdimm_flush() for namespace I/O writes
fs/dax: remove wmb_pmem()
libnvdimm, pmem: flush posted-write queues on shutdown
...
|
|
Pull block driver updates from Jens Axboe:
"This branch also contains core changes. I've come to the conclusion
that from 4.9 and forward, I'll be doing just a single branch. We
often have dependencies between core and drivers, and it's hard to
always split them up appropriately without pulling core into drivers
when that happens.
That said, this contains:
- separate secure erase type for the core block layer, from
Christoph.
- set of discard fixes, from Christoph.
- bio shrinking fixes from Christoph, as a followup up to the
op/flags change in the core branch.
- map and append request fixes from Christoph.
- NVMeF (NVMe over Fabrics) code from Christoph. This is pretty
exciting!
- nvme-loop fixes from Arnd.
- removal of ->driverfs_dev from Dan, after providing a
device_add_disk() helper.
- bcache fixes from Bhaktipriya and Yijing.
- cdrom subchannel read fix from Vchannaiah.
- set of lightnvm updates from Wenwei, Matias, Johannes, and Javier.
- set of drbd updates and fixes from Fabian, Lars, and Philipp.
- mg_disk error path fix from Bart.
- user notification for failed device add for loop, from Minfei.
- NVMe in general:
+ NVMe delay quirk from Guilherme.
+ SR-IOV support and command retry limits from Keith.
+ fix for memory-less NUMA node from Masayoshi.
+ use UINT_MAX for discard sectors, from Minfei.
+ cancel IO fixes from Ming.
+ don't allocate unused major, from Neil.
+ error code fixup from Dan.
+ use constants for PSDT/FUSE from James.
+ variable init fix from Jay.
+ fabrics fixes from Ming, Sagi, and Wei.
+ various fixes"
* 'for-4.8/drivers' of git://git.kernel.dk/linux-block: (115 commits)
nvme/pci: Provide SR-IOV support
nvme: initialize variable before logical OR'ing it
block: unexport various bio mapping helpers
scsi/osd: open code blk_make_request
target: stop using blk_make_request
block: simplify and export blk_rq_append_bio
block: ensure bios return from blk_get_request are properly initialized
virtio_blk: use blk_rq_map_kern
memstick: don't allow REQ_TYPE_BLOCK_PC requests
block: shrink bio size again
block: simplify and cleanup bvec pool handling
block: get rid of bio_rw and READA
block: don't ignore -EOPNOTSUPP blkdev_issue_write_same
block: introduce BLKDEV_DISCARD_ZERO to fix zeroout
NVMe: don't allocate unused nvme_major
nvme: avoid crashes when node 0 is memoryless node.
nvme: Limit command retries
loop: Make user notify for adding loop device failed
nvme-loop: fix nvme-loop Kconfig dependencies
nvmet: fix return value check in nvmet_subsys_alloc()
...
|
|
Pull core block updates from Jens Axboe:
- the big change is the cleanup from Mike Christie, cleaning up our
uses of command types and modified flags. This is what will throw
some merge conflicts
- regression fix for the above for btrfs, from Vincent
- following up to the above, better packing of struct request from
Christoph
- a 2038 fix for blktrace from Arnd
- a few trivial/spelling fixes from Bart Van Assche
- a front merge check fix from Damien, which could cause issues on
SMR drives
- Atari partition fix from Gabriel
- convert cfq to highres timers, since jiffies isn't granular enough
for some devices these days. From Jan and Jeff
- CFQ priority boost fix idle classes, from me
- cleanup series from Ming, improving our bio/bvec iteration
- a direct issue fix for blk-mq from Omar
- fix for plug merging not involving the IO scheduler, like we do for
other types of merges. From Tahsin
- expose DAX type internally and through sysfs. From Toshi and Yigal
* 'for-4.8/core' of git://git.kernel.dk/linux-block: (76 commits)
block: Fix front merge check
block: do not merge requests without consulting with io scheduler
block: Fix spelling in a source code comment
block: expose QUEUE_FLAG_DAX in sysfs
block: add QUEUE_FLAG_DAX for devices to advertise their DAX support
Btrfs: fix comparison in __btrfs_map_block()
block: atari: Return early for unsupported sector size
Doc: block: Fix a typo in queue-sysfs.txt
cfq-iosched: Charge at least 1 jiffie instead of 1 ns
cfq-iosched: Fix regression in bonnie++ rewrite performance
cfq-iosched: Convert slice_resid from u64 to s64
block: Convert fifo_time from ulong to u64
blktrace: avoid using timespec
block/blk-cgroup.c: Declare local symbols static
block/bio-integrity.c: Add #include "blk.h"
block/partition-generic.c: Remove a set-but-not-used variable
block: bio: kill BIO_MAX_SIZE
cfq-iosched: temporarily boost queue priority for idle classes
block: drbd: avoid to use BIO_MAX_SIZE
block: bio: remove BIO_MAX_SECTORS
...
|
|
|
|
"__nd_device_register"
The __nd_device_register() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Normally, an ARS (Address Range Scrub) only happens at
boot/initialization time. There can however arise situations where a
bus-wide rescan is needed - notably, in the case of discovering a latent
media error, we should do a full rescan to figure out what other sectors
are bad, and thus potentially avoid triggering an mce on them in the
future. Also provide a sysfs trigger to start a bus-wide scrub.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
A recent effort to add a new nvdimm bus provider attribute highlighted a
race between interrogating nvdimm_bus->nd_desc and nvdimm_bus tear down.
The typical way to handle these races is to take the device_lock() in
the attribute method and validate that the device is still active. In
order for a device to be 'active' it needs to be associated with a
driver. So, we create the small boilerplate for a driver and register
nvdimm_bus devices on the 'nvdimm_bus_type' bus.
A result of this change is that ndbusX devices now appear under
/sys/bus/nd/devices. In fact this makes /sys/class/nd somewhat
redundant, but removing that will need to take a long deprecation period
given its use by ndctl binaries in the field.
This change naturally pulls code from drivers/nvdimm/core.c to
drivers/nvdimm/bus.c, so it is a nice code organization clean-up as
well.
Cc: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Prefix the sector number being cleared with a '0x' to make it clear that
this is a hex value.
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Let the provider module be explicitly passed in rather than implicitly
assumed by the module that calls nvdimm_bus_register(). This is in
preparation for unifying the nfit and nfit_test driver teardown paths.
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Currently, presence of direct_access() in block_device_operations
indicates support of DAX on its block device. Because
block_device_operations is instantiated with 'const', this DAX
capablity may not be enabled conditinally.
In preparation for supporting DAX to device-mapper devices, add
QUEUE_FLAG_DAX to request_queue flags to advertise their DAX
support. This will allow to set the DAX capability based on how
mapped device is composed.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: <linux-s390@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The __pmem address space was meant to annotate codepaths that touch
persistent memory and need to coordinate a call to wmb_pmem(). Now that
wmb_pmem() is gone, there is little need to keep this annotation.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
nsio_rw_bytes() is used to write info block metadata to the namespace,
so it should trigger a flush after every write. Replace wmb_pmem() with
nvdimm_flush() in this path.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Commit writes to media on system shutdown or pmem driver unload.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Given that nvdimm_flush() has higher overhead than wmb_pmem() (pointer
chasing through nd_region), and that we otherwise assume a platform has
ADR capability when flush hints are not present, move nvdimm_flush() to
REQ_FLUSH context.
Note that we still arrange for nvdimm_flush() to be called even in the
ADR case. We need at least once wmb() fence to push buffered writes in
the cpu out to the ADR protected domain.
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
When the NFIT provides multiple flush hint addresses per-dimm it is
expressing that the platform is capable of processing multiple flush
requests in parallel. There is some fixed cost per flush request, let
the cost be shared in parallel on multiple cpus.
Since there may not be enough flush hint addresses for each cpu to have
one, keep a per-cpu index of the last used hint, hash it with current
pid, and assume that access pattern and scheduler randomness will keep
the flush-hint usage somewhat staggered across cpus.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
nvdimm_flush() is a replacement for the x86 'pcommit' instruction. It is
an optional write flushing mechanism that an nvdimm bus can provide for
the pmem driver to consume. In the case of the NFIT nvdimm-bus-provider
nvdimm_flush() is implemented as a series of flush-hint-address [1]
writes to each dimm in the interleave set (region) that backs the
namespace.
The nvdimm_has_flush() routine relies on platform firmware to describe
the flushing capabilities of a platform. It uses the heuristic of
whether an nvdimm bus provider provides flush address data to return a
ternary result:
1: flush addresses defined
0: dimm topology described without flush addresses (assume ADR)
-errno: no topology information, unable to determine flush mechanism
The pmem driver is expected to take the following actions on this ternary
result:
1: nvdimm_flush() in response to REQ_FUA / REQ_FLUSH and shutdown
0: do not set, WC or FUA on the queue, take no further action
-errno: warn and then operate as if nvdimm_has_flush() returned '0'
The caveat of this heuristic is that it can not distinguish the "dimm
does not have flush address" case from the "platform firmware is broken
and failed to describe a flush address". Given we are already
explicitly trusting the NFIT there's not much more we can do beyond
blacklisting broken firmwares if they are ever encountered.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
nd_region device driver data will be used in the namespace i/o path.
Re-order nd_region_remove() to ensure this data stays live across
namespace device removal
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
In preparation for triggering flushes of a DIMM's writes-posted-queue
(WPQ) via the pmem driver move mapping of flush hint addresses to the
region driver. Since this uses devm_nvdimm_memremap() the flush
addresses will remain mapped while any region to which the dimm belongs
is active.
We need to communicate more information to the nvdimm core to facilitate
this mapping, namely each dimm object now carries an array of flush hint
address resources.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Now that all shared mappings are handled by devm_nvdimm_memremap() we no
longer need nfit_spa_map() nor do we need to trigger a callback to the
bus provider at region disable time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
In preparation for generically mapping flush hint addresses for both the
BLK and PMEM use case, provide a generic / reference counted mapping
api. Given the fact that a dimm may belong to multiple regions (PMEM
and BLK), the flush hint addresses need to be held valid as long as any
region associated with the dimm is active. This is similar to the
existing BLK-region case where multiple BLK-regions may share an
aperture mapping. Up-level this shared / reference-counted mapping
capability from the nfit driver to a core nvdimm capability.
This eliminates the need for the nd_blk_region.disable() callback. Note
that the removal of nfit_spa_map() and related infrastructure is
deferred to a later patch.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Initialize struct blk_integrity with 0 as blk_integrity_register() takes the
then unitialized struct blk_integrity::flags and ORs it to the resulting block
integrity structure.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Now that all drivers that specify a ->driverfs_dev have been converted
to device_add_disk(), the pointer can be removed from struct gendisk.
Cc: Jens Axboe <axboe@fb.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
For block drivers that specify a parent device, convert them to use
device_add_disk().
This conversion was done with the following semantic patch:
@@
struct gendisk *disk;
expression E;
@@
- disk->driverfs_dev = E;
...
- add_disk(disk);
+ device_add_disk(E, disk);
@@
struct gendisk *disk;
expression E1, E2;
@@
- disk->driverfs_dev = E1;
...
E2 = disk;
...
- add_disk(E2);
+ device_add_disk(E1, E2);
...plus some manual fixups for a few missed conversions.
Cc: Jens Axboe <axboe@fb.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Currently phys_to_pfn_t() is an exported symbol to allow nfit_test to
override it and indicate that nfit_test-pmem is not device-mapped. Now,
we want to enable nfit_test to operate without DMA_CMA and the pmem it
provides will no longer be physically contiguous, i.e. won't be capable
of supporting direct_access requests larger than a page. Make
pmem_direct_access() a weak symbol so that it can be replaced by the
tools/testing/nvdimm/ version, and move phys_to_pfn_t() to a static
inline now that it no longer needs to be overridden.
Acked-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The updated ndctl unit tests discovered that if a pfn configuration with
a 4K alignment is read from the namespace, that alignment will be
ignored in favor of the default 2M alignment. The result is that the
configuration will fail initialization with a message like:
dax6.1: bad offset: 0x22000 dax disabled align: 0x200000
Fix this by allowing the alignment read from the info block to override
the default which is 2M not 0 in the autodetect path. This also fixes a
similar problem with the mode and alignment settings silently being
overwritten by the kernel when userspace has changed it. We now will
either overwrite the info block if userspace changes the uuid or fail
and warn if a live setting disagrees with the info block.
Cc: <stable@vger.kernel.org>
Cc: Micah Parrish <micah.parrish@hpe.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Prompted by commit 287980e49ffc "remove lots of IS_ERR_VALUE abuses", I
ran make coccicheck against drivers/nvdimm/ and found that:
if (IS_ERR(x))
return PTR_ERR(x);
return 0;
...can be replaced with PTR_ERR_OR_ZERO().
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Clean up needless calls to the action routine by letting
devm_add_action_or_reset() call it automatically. This does cause the
disk to registered and immediately unregistered when a memory allocation
fails, but the block layer should be prepared for such an event.
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull misc DAX updates from Vishal Verma:
"DAX error handling for 4.7
- Until now, dax has been disabled if media errors were found on any
device. This enables the use of DAX in the presence of these
errors by making all sector-aligned zeroing go through the driver.
- The driver (already) has the ability to clear errors on writes that
are sent through the block layer using 'DSMs' defined in ACPI 6.1.
Other misc changes:
- When mounting DAX filesystems, check to make sure the partition is
page aligned. This is a requirement for DAX, and previously, we
allowed such unaligned mounts to succeed, but subsequent
reads/writes would fail.
- Misc/cleanup fixes from Jan that remove unused code from DAX
related to zeroing, writeback, and some size checks"
* tag 'dax-misc-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: fix a comment in dax_zero_page_range and dax_truncate_page
dax: for truncate/hole-punch, do zeroing through the driver if possible
dax: export a low-level __dax_zero_page_range helper
dax: use sb_issue_zerout instead of calling dax_clear_sectors
dax: enable dax in the presence of known media errors (badblocks)
dax: fallback from pmd to pte on error
block: Update blkdev_dax_capable() for consistency
xfs: Add alignment check for DAX mount
ext2: Add alignment check for DAX mount
ext4: Add alignment check for DAX mount
block: Add bdev_dax_supported() for dax mount checks
block: Add vfs_msg() interface
dax: Remove redundant inode size checks
dax: Remove pointless writeback from dax_do_io()
dax: Remove zeroing from dax_io()
dax: Remove dead zeroing code from fault handlers
ext2: Avoid DAX zeroing to corrupt data
ext2: Fix block zeroing in ext2_get_blocks() for DAX
dax: Remove complete_unwritten argument
DAX: move RADIX_DAX_ definitions to dax.c
|
|
|
|
The ndctl unit tests discovered that the dax enabling omitted updates to
nd_detach_and_reset(). This routine clears device the configuration
when the namespace is detached. Without this clearing userspace may
assume that the device is in the process of being configured by another
agent in the system.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Testing the dax-device autodetect support revealed a probe failure with
the following result:
dax0.1: bad offset: 0x8200000 dax disabled
The original pfn-device implementation inferred the alignment from
ilog2(offset), now that the alignment is explicit the is_power_of_2()
needs replacing with a real sanity check against the recorded alignment.
Otherwise the alignment check is useless in the implicit case and only
the minimum size of the offset matters.
This self-consistency check is further validated by the probe path that
will re-check that the offset is large enough to contain all the
metadata required to enable the device.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
For autodetecting a previously established dax configuration we need the
info block to indicate block-device vs device-dax mode, and we need to
have the default namespace probe hand-off the configuration to the
dax_pmem driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
ida instances allocate some internal memory for ->free_bitmap in
addition to the base 'struct ida'. Use ida_destroy() to release that
memory at module_exit().
Reported-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
1/ If a mapping overlaps a bad sector fail the request.
2/ Do not opportunistically report more dax-capable capacity than is
requested when errors present.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[vishal: fix a conflict with system RAM collision patches]
[vishal: add a 'size' parameter to ->direct_access]
[vishal: fix a conflict with DAX alignment check patches]
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
|
|
|
|
|
|
|
|
The dax_pmem driver was implementing an empty ->remove() method to
satisfy the nvdimm bus driver that unconditionally calls ->remove().
Teach the core bus driver to check if ->remove() is NULL to remove that
requirement.
Reported-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
We want to use the alignment as the allocation and mapping unit.
Previously this information was only useful for establishing the data
offset, but now it is important to remember the granularity for the
later use.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
We may want to subdivide a device-dax range into multiple devices so
that each can have separate permissions or naming. Reserve 128K of
label space by default so we have the capability of making allocation
decisions persistent. This reservation is not something we can add
later since it would result in the default size of a device-dax range
changing between kernel versions.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Device DAX is the device-centric analogue of Filesystem DAX
(CONFIG_FS_DAX). It allows persistent memory ranges to be allocated and
mapped without need of an intervening file system. This initial
infrastructure arranges for a libnvdimm pfn-device to be represented as
a different device-type so that it can be attached to a driver other
than the pmem driver.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
I had relied on the kbuild robot for cross build coverage, however it
only builds alpha_defconfig. Switch from HPAGE_SIZE to PMD_SIZE, which
is more widely defined.
Fixes: 658922e57b84 ("libnvdimm, pfn: fix memmap reservation sizing")
Cc: <stable@vger.kernel.org>
Reported-by: Guenter Roeck <guenter@roeck-us.net>
Tested-by: Guenter Roeck <guenter@roeck-us.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
When configuring a pfn-device instance to allocate the memmap array it
needs to account for the fact that vmemmap_populate_hugepages()
allocates struct page blocks in HPAGE_SIZE chunks. We need to align the
reserved area size to 2MB otherwise arch_add_memory() runs out of memory
while establishing the memmap:
WARNING: CPU: 0 PID: 496 at arch/x86/mm/init_64.c:704 arch_add_memory+0xe7/0xf0
[..]
Call Trace:
[<ffffffff8148bdb3>] dump_stack+0x85/0xc2
[<ffffffff810a749b>] __warn+0xcb/0xf0
[<ffffffff810a75cd>] warn_slowpath_null+0x1d/0x20
[<ffffffff8106a497>] arch_add_memory+0xe7/0xf0
[<ffffffff811d2097>] devm_memremap_pages+0x287/0x450
[<ffffffff811d1ffa>] ? devm_memremap_pages+0x1ea/0x450
[<ffffffffa0000298>] __wrap_devm_memremap_pages+0x58/0x70 [nfit_test_iomap]
[<ffffffffa0047a58>] pmem_attach_disk+0x318/0x420 [nd_pmem]
[<ffffffffa0047bcf>] nd_pmem_probe+0x6f/0x90 [nd_pmem]
[<ffffffffa0009469>] nvdimm_bus_probe+0x69/0x110 [libnvdimm]
[..]
ndbus0: nd_pmem.probe(pfn3.0) = -12
nd_pmem: probe of pfn3.0 failed with error -12
libndctl: ndctl_pfn_enable: pfn3.0: failed to enable
Reported-by: Namratha Kothapalli <namratha.n.kothapalli@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
There are currently 4 known similar but incompatible definitions of the
command sets that can be sent to an NVDIMM through ACPI. It is also
clear that future platform generations (ACPI or not) will continue to
revise and extend the DIMM command set as new devices and use cases
arrive.
It is obviously untenable to continue to proliferate divergence
of these command definitions, and to that end a standardization process
has begun to provide for a unified specification. However, that leaves a
problem about what to do with this first generation where vendors are
already shipping divergence.
The Linux kernel can support these initial diverged platforms without
giving platform-firmware free reign to continue to diverge and compound
kernel maintenance overhead. The kernel implementation can encourage
standardization in two ways:
1/ Require that any function code that userspace wants to send be
explicitly white-listed in the implementation. For ACPI this means
function codes marked as supported by acpi_check_dsm() may
only be invoked if they appear in the white-list. A function must be
publicly documented before it is added to the white-list.
2/ The above restrictions can be trivially bypassed by using the
"vendor-specific" payload command. However, since vendor-specific
commands are by definition not publicly documented and have the
potential to corrupt the kernel's view of the dimm state, we provide a
toggle to disable vendor-specific operations. Enabling undefined
behavior is a policy decision that can be made by the platform owner
and encourages firmware implementations to choose public over
private command implementations.
Based on an initial patch from Jerry Hoemann
Cc: Jerry Hoemann <jerry.hoemann@hpe.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Clarify the distinction between "commands", the ioctls userspace calls
to request the kernel take some action on a given dimm device, and
"_DSMs", the actual function numbers used in the firmware interface to
the DIMM. _DSMs are ACPI specific whereas commands are Linux kernel
generic.
This is in preparation for breaking the 1:1 implicit relationship
between the kernel ioctl number space and the firmware specific function
numbers.
Cc: Jerry Hoemann <jerry.hoemann@hpe.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The 'host' variable can be killed as it is always the same as the passed
in device.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
