| Age | Commit message (Collapse) | Author |
|---|
|
If we reload phy-twl4030-usb, we get a warning about unbalanced
pm_runtime_enable. Let's fix the issue and also fix idling of the
device on unload before we attempt to shut it down.
If we don't properly idle the PHY before shutting it down on removal,
the twl4030 ends up consuming about 62mW of extra power compared to
running idle with the module loaded.
Cc: stable@vger.kernel.org
Cc: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Otherwise rmmod omap2430; rmmod phy-twl4030-usb; modprobe omap2430
will try to use a non-existing phy and oops:
Unable to handle kernel paging request at virtual address b6f7c1f0
...
[<c048a284>] (devm_usb_get_phy_by_node) from [<bf0758ac>]
(omap2430_musb_init+0x44/0x2b4 [omap2430])
[<bf0758ac>] (omap2430_musb_init [omap2430]) from [<bf055ec0>]
(musb_init_controller+0x194/0x878 [musb_hdrc])
Cc: stable@vger.kernel.org
Cc: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
If phy_pm_runtime_get_sync failed but we already
enable regulator, current code return directly without
doing regulator_disable. This patch fix this problem
and cleanup err handle of phy_power_on to be more readable.
Fixes: 3be88125d85d ("phy: core: Support regulator ...")
Cc: <stable@vger.kernel.org> # v3.18+
Cc: Roger Quadros <rogerq@ti.com>
Cc: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The HiSilicon Hi6220 USB PHY is available in HiSilicon Hi6220 SoCs only.
Restrict it to HiSilicon arm64, unless compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.5
*) new PHY driver for hi6220 usb and rcar gen3 usb2
*) deprecate phy-omap-control driver. phy-omap-control driver was added
when there was no proper infrastructure for doing control module
initialization. The phy-omap-control driver is not an 'actual' PHY
driver and it was just a hack to do PHY related control module
initialization. Now with SYSCON framework in the kernel, control
module setttings can be done using APIs provided by syscon.
*) usbphy-internal pll creates the needed 480MHz and is also a
supply-clock back to the core clock-controller in Rockchip SoCs.
This is now modeled as a real clock.
*) calibrate mt65xx usb3 PHY for better eye diagram and receiver
sensitivity.
*) Miscellaneous cleanups.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.5
A ton of improvements to dwc2 have been made. The
driver should be a lot more stable on v4.5 then ever
before.
Our good old dwc3 got a few cleanups and misc fixes
and also added support to Xilinx's integration of
this IP.
Yoshihiro Shimoda gives us support for a new USB3
peripheral controller from Renesas.
Other than these, the usual misc fixes all over the
place.
|
|
Deprecate using phy-omap-control driver to power on/off the PHY,
and use *syscon* framework to do the same. This handles
powering on/off the PHY for the USB2 PHYs used in various TI SoCs.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
No functional change. Previously omap_control_phy_power() was used to power
off the PHY during probe. But once phy-omap-usb2 driver is adapted to
use syscon, omap_control_phy_power() cannot be used. Hence used
omap_usb_power_off to power off the PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
|
|
Deprecate using phy-omap-control driver to set PCS value of the PHY
and start using *syscon* API to do the same.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
Deprecate using phy-omap-control driver to power on/off the PHY and
use *syscon* framework to do the same.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
No functional change. Previously omap_control_phy_power() was used to power
off the PHY during probe. But once PIPE3 driver is adapted to use syscon,
omap_control_phy_power() cannot be used. Hence used ti_pipe3_power_off
to power off the PHY.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
|
|
No functional change. Moved mem resource initialization done in
probe to a separate function as part of cleaning up
ti_pipe3_probe.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
No functional change. Moved sysctrl initialization done in probe to a
separate function as part of cleaning up ti_pipe3_probe.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
No functional change. Moved clock initialization done in probe to a
separate function as part of cleaning up ti_pipe3_probe.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
No functional change. Introduce local struct device pointer in
probe and replace using &pdev->dev/phy->dev with the local
device pointer. This is in preparation to split ti_pipe3_probe
and add separate functions for getting mem resource, getting
sysctrl and getting clocks.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
After commit 739ae3452d0e ("phy: berlin-usb: Set drvdata for phy and
use it"), we get the address of priv by phy_get_drvdata(), so there's
no need to set device's driver_data any more. This patch removes the
call of platform_set_drvdata().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
We don't need gpio related header files, so remove them.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The BCM7xxx ARM-based and MIPS-based platforms share a similar hardware
block for AHCI SATA3.
This new compatible string, "brcm,bcm7425-sata-phy", may be used for
most MIPS-based platforms of 40nm process technology.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add data for phy version, and the default value of version is using the
BRCM_SATA_PHY_28NM.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Remove duplicate definitions.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The USB phys on Rockchip SoCs contain their own internal PLLs to create
the 480MHz needed. Additionally this PLL output is also fed back into the
core clock-controller as possible source for clocks like the GPU or others.
Until now this was modelled incorrectly with a "virtual" factor clock in
the clock controller. The one big caveat is that if we turn off the usb phy
via the siddq signal, all analog components get turned off, including the
PLLs. It is therefore possible that a source clock gets disabled without
the clock driver ever knowing, possibly making the system hang.
Therefore register the phy-plls as real clocks that the clock driver can
then reference again normally, making the clock hirarchy finally reflect
the actual hardware.
The phy-ops get converted to simply turning that new clock on and off
which in turn controls the siddq signal of the phy.
Through this the driver gains handling for platform-specific data, to
handle the phy->clock name association.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
We need custom handling for these two socs in the driver shortly,
so add the necessary compatible values to binding and driver.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This unclutters the loop in probe a lot and makes current (and future)
error handling easier to read.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This introduces a common struct that holds data belonging to
the umbrella device that contains all the phys and that we
want to use later.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Currently the phy driver only gets the optional clock reference but
never puts it again, neither during error handling nor on remove.
Fix that by moving the clk_put to a devm-action that gets called at
the right time when all other devm actions are done.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Support hi6220 use phy for HiKey board
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Note this commit only adds support for phys 1-3, phy 0, the otg phy, is
not yet (fully) supported after this commit.
Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Use of_match_node instead of calling of_device_is_compatible a ton of
times to get model specific config data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
calibrate HS slew rate and switch 100uA current to SSUSB
to improve HS eye diagram of HQA test.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
when use the default value 8 of RG_USB20_SQTH, the HS receiver
sensitivity test of HQA will fail, set it as 2 to fix up the
issue.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch adds support for runtime ID/VBUS pin detection if
the channel 0 of R-Car gen3 is used. So, we are able to use
the channel as both host and peripheral.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
To use the channel 0 of R-Car gen3 as periperal mode, This patch changes
the mode to OTG instead of HOST. Then, this driver needs to set some
registers to enable host mode and detects ID pin and VBUS pin at
phy_init() timing.
For now, the channel 0 can be used as host mode only.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch adds support for R-Car generation 3 USB2 PHY driver.
This SoC has 3 EHCI/OHCI channels, and the channel 0 is shared
with the HSUSB (USB2.0 peripheral) device. And each channel has
independent registers about the PHYs.
So, the purpose of this driver is:
1) initializes some registers of SoC specific to use the
{ehci,ohci}-platform driver.
2) detects id pin to select host or peripheral on the channel 0.
For now, this driver only supports 1) above.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
We currently can't unload omap2430 MUSB platform glue driver module and
this cause issues for fixing the MUSB code further. The reason we can't
remove omap2430 is because it uses the PHY functions and also exports the
omap_musb_mailbox function that some PHY drivers are using.
Let's fix the issue by exporting a more generic musb_mailbox function
from the MUSB core and allow platform glue layers to register phy_callback
function as needed.
And now we can now also get rid of the include/linux/musb-omap.h.
Cc: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: NeilBrown <neil@brown.name>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
On driver detach, devm_phy_release() will put a refcount to
the phy, so gets a refconut to it before return.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
for_each_available_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
for_each_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
for_each_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
for_each_available_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
for_each_available_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
for_each_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
for_each_available_child_of_node performs an of_node_get on each iteration,
so a return from the middle of the loop requires an of_node_put.
A simplified version of the semantic patch that finds this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_available_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
* return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The sun9i usb phy driver calls of_usb_get_phy_mode(), which is not
available if USB is disabled:
drivers/built-in.o: In function `sun9i_usb_phy_probe':
:(.text+0x7fb0): undefined reference to `of_usb_get_phy_mode'
This adds a dependency to avoid the randconfig build errors.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9c3b44302636 ("phy: Add driver to support individual USB PHYs on sun9i")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.4-rc1.
As usual, most of the changes are in the gadget subsystem, and we
removed a host controller for a device that is no longer in existance,
and probably never was even made public. There is also other minor
driver updates and new device ids, full details in the changelog.
All of these have been in linux-next for a while"
* tag 'usb-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (233 commits)
USB: core: Codestyle fix in urb.c
usb: misc: usb3503: Use i2c_add_driver helper macro
usb: host: lpc32xx: don't unregister phy device
usb: host: lpc32xx: balance clk enable/disable on removal
usb: host: lpc32xx: fix warnings caused by enabling unprepared clock
uwb: drp: Use setup_timer
uwb: neh: Use setup_timer
uwb: rsv: Use setup_timer
USB: qcserial: add Sierra Wireless MC74xx/EM74xx
usb: chipidea: otg: don't wait vbus drops below BSV when starts host
chipidea: ci_hdrc_pci: use PCI_VDEVICE() instead of PCI_DEVICE()
doc: dt-binding: ci-hdrc-usb2: split vendor specific properties
usb: chipidea: imx: add imx6ul usb support
doc: dt-binding: ci-hdrc-usb2: improve property description
usb: chipidea: imx: add usb support for imx7d
Doc: usb: ci-hdrc-usb2: Add phy-clkgate-delay-us entry
usb: chipidea: Add support for 'phy-clkgate-delay-us' property
usb: chipidea: Use extcon framework for VBUS and ID detect
usb: gadget: net2280: restore ep_cfg after defect7374 workaround
usb: dwc2: host: Fix use after free w/ simultaneous irqs
...
|
|
changes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.4
*) Add new PHY driver for Broadcom's cygnus PCIe PHY
*) Add USB3 PHY driver for mediatek's SoCs
*) Add VBUS regulator support for Samsung's exynos PHY
*) Misc cleanup
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This patch adds the PCIe PHY support for the Broadcom PCIe RC interface
on Cygnus
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Arun Parameswaran <aparames@broadcom.com>
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Both data->id_det_gpio and data->vbus_det_gpio are optional, so use
devm_gpiod_get_optional for them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
support usb3.0 phy of mt65xx SoCs
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Exynos USB2 PHY has separate power supply, which is usually provided by
VBUS regulator. This patch adds support for it. VBUS regulator is
optional, to keep compatibility with boards, which have VBUS provided
from some always-on power source.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
