| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds IRQ support to STM32 gpios.
The EXTI controller has 16 lines dedicated to GPIOs.
EXTI line n can be connected to only line n of one of the GPIO ports, for
example EXTI0 can be connected to either PA0, or PB0, or PC0...
This port selection is done by specifying the port number into System
Config registers.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
While only Freescale Vybrid SoC has settings of GPIO capabilities done
by iomux controller, it is only a matter of GPIO controller driver
implementation for the rest of Freescale/NXP SoCs from iMX series.
As a practical example on GPIO request a pad function should be
switched to GPIO, but because this requires updates to all particular
iMX pinctrl drivers, for simplicity at the moment add only a proper
connection between shared pinctrl-imx and pinctrl/pinmux core, namely
.gpio_request_enable/.gpio_disable_free/.gpio_set_direction callbacks
should return success to a caller. This change allows to progress by
adding request/free callbacks into gpio-mxc.c driver.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
at91 used to set a default trigger type for GPIO interrupts in
order to cope with the old board files. These days are long gone,
and it all gets probed through DT.
Andras Szemzo reported that the Ethernet device on his board was
bailing to be probed, due to a conflict in interrupt trigger.
Surely enough, this is due to this default trigger still being
present, and turning this into a IRQ_TYPE_NONE fixes the issue.
Reported-by: Andras Szemzo <szemzo.andras@gmail.com>
Tested-by: Andras Szemzo <szemzo.andras@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
H3 has single PWM channel. The second PWM channel is not supported,
so the pinctrl function should be removed.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Check for pinctrl_ops and pinmux_ops structures that are only stored in the
pctlops field and the pmxops field, respectively, of a pinctrl_desc
structure. These fields are declared const, so pinctrl_ops and pinmux_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change in the pinctrl_ops is as
follows. The pinmux_ops case is similar. (http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct pinctrl_ops i@p = { ... };
@ok@
identifier r.i;
struct pinctrl_desc e;
position p;
@@
e.pctlops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct pinctrl_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct pinctrl_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Check for pinctrl_ops and pinmux_ops structures that are only stored in the
pctlops field and the pmxops field, respectively, of a pinctrl_desc
structure. These fields are declared const, so pinctrl_ops and pinmux_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change in the pinctrl_ops is as
follows. The pinmux_ops case is similar. (http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct pinctrl_ops i@p = { ... };
@ok@
identifier r.i;
struct pinctrl_desc e;
position p;
@@
e.pctlops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct pinctrl_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct pinctrl_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Check for pinctrl_ops and pinmux_ops structures that are only stored in the
pctlops field and the pmxops field, respectively, of a pinctrl_desc
structure. These fields are declared const, so pinctrl_ops and pinmux_ops
structures that have this property can be declared as const also.
The semantic patch that makes this change in the pinctrl_ops is as
follows. The pinmux_ops case is similar. (http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct pinctrl_ops i@p = { ... };
@ok@
identifier r.i;
struct pinctrl_desc e;
position p;
@@
e.pctlops = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct pinctrl_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct pinctrl_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In the function amd_gpio_irq_set_type, use the settings provided by
the BIOS,when the LevelTrig is Edge and activeLevel is HIGH, to configure
the GPIO registers. Ignore the settings from client.
Reviewed-by: Pankaj Sen <Pankaj.Sen@amd.com>
Signed-off-by:Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Just like the other member of the sunxi family, let's add a pinctrl table
for the muxing options.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A small subset of pins and functions are exposed. The selection of pins
and functions is driven by the development of OpenBMC[1] on the
AST2500 SoC, particularly around booting the IBM Witherspoon platform.
[1] https://github.com/openbmc/docs
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A subset of the pins and functions are exposed. The selection of
functions and pins is driven by the development of OpenBMC[1] on the
AST2400 SoC, particularly around booting the OpenPOWER Palmetto
development machine.
[1] https://github.com/openbmc/docs
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Aspeed SoCs typically provide more than 200 pins for GPIO and other
functions. The signal enabled on a pin is determined on a priority
basis, where a given pin can provide a number of different signal types.
In addition to the priority levels, the Aspeed pin controllers describe
the signal active on a pin by compound logical expressions involving
multiple operators, registers and bits. Some difficulty arises as a
pin's function bit masks for each priority level are frequently not the
same (i.e. we cannot just flip a bit to change from a high to low
priority signal), or even in the same register(s). Some configuration
bits affect multiple pins, while in other cases the signals for a bus
must each be enabled individually.
Together, these features give rise to some complexity in the
implementation. A more complete description of the complexities is
provided in the associated header file.
The patch doesn't implement pinctrl/pinmux/pinconf for any particular
Aspeed SoC, rather it adds the framework for defining pinmux
configurations.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
sd_emmc_a is used a controller for the SDIO modules. This adds the pin
configuration for the SDIO controller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It contains pin 50 instead of pin 40.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Add support for R-Car M3-W
Add initial support for the Pin Function Controller on the Renesas R-Car
M3-W SoC:
- Basic definitions,
- SCIF (serial) pins, groups and functions,
- SDHI pins, groups and functions.
|
|
cat /sys/kernel/debug/pinctrl/${pinctrl}/pinconf-groups output is
hardly readable, if a pin group contains more than one pin the output
is glued and looks like this:
MX6Q_PAD_SD1_DAT0: 0x17071MX6Q_PAD_SD1_CMD: 0x17071MX6Q_PAD_SD1_CLK: 0x17071
Add two space indentation and a new line separator to improve
readability of the output.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Makefile currently controlling compilation of this code is:
drivers/pinctrl/sirf/pinctrl-sirf.o
--> drivers/pinctrl/sirf/Makefile:obj-y += pinctrl-sirf.o
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rongjun Ying <rongjun.ying@csr.com>
Cc: Yuping Luo <yuping.luo@csr.com>
Cc: Barry Song <baohua@kernel.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Makefile currently controlling compilation of this code is:
drivers/pinctrl/sirf/pinctrl-atlas7.o
---> drivers/pinctrl/sirf/Makefile:obj-y += pinctrl-atlas7.o
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Barry Song <baohua@kernel.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/Kconfig:config PINCTRL_ROCKCHIP
drivers/pinctrl/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-gpio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/nomadik/Kconfig:config PINCTRL_NOMADIK
drivers/pinctrl/nomadik/Kconfig: bool "Nomadik pin controller driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig currently controlling compilation of this code is:
config PINCTRL_ABX500
bool "ST-Ericsson ABx500 family Mixed Signal Circuit gpio functions"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Note that MODULE_ALIAS is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Makefile currently controlling compilation of this code is:
drivers/pinctrl/mediatek/pinctrl-mtk-common.o
---> drivers/pinctrl/mediatek/Makefile:obj-y += pinctrl-mtk-common.o
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We don't replace module.h with init.h since the file doesn't need that.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Hongzhou Yang <hongzhou.yang@mediatek.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add support for PWM pins, for EE and AO domains.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.9
- Bias and DU support for R-Car H3,
- Basic R-Car V2H support,
- Cleanups and fixes.
|
|
This adds the IR remote receiver to the AO domain devices.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
of_match_device could return NULL, and so cause a NULL pointer
dereference later at line 1009:
pinctrl_data = match->data;
For fixing this problem, we use of_device_get_match_data(), this will
simplify the code a little by using a standard function for
getting the match data.
Reported-by: coverity (CID 1324136)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Because chained_irq_enter() has already called chip->irq_mask() and
chip->irq_ack(), also chained_irq_exit() will call chip->irq_unmask(),
so it's not necessary to call chip->irq_*() here.
Signed-off-by: Perr Zhang <strongbox8@zoho.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[Hand-edited from whitespace damaged patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The driver originally supported more domains (register ranges) per
pinctrl device, but since commit 9dab1868ec0d ("pinctrl: amlogic: Make
driver independent from two-domain configuration") each device gets
assigned a single domain and we instantiate multiple pinctrl devices
in the DT.
Therefore, now the 'meson_domain' and 'meson_domain_data' structures
don't have any reason to exist and can be removed to make the model
simpler to understand. This commit doesn't change behavior.
Tested on a Odroid-C2.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds SDHI pins, groups and functions to R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds SCIF{0,1,2,3,4,5} pins, groups and functions to R8A7796
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds initial pinctrl driver to support for the R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[uli: rebased on top of renesas-drivers]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Only the DU parallel RGB output signals are included, HDMI and TCON pins
will be added in separate groups.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch allows to use the second parameter of gpio
specifier, which is used to specify whether the gpio is
active high or low.
Simply remove specific of_xlate callback() and of_gpio_n_cells
and use default one set by of_gpiochip_add() which allows
to use second parameter gpio specifier.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,x;
@@
- if (of_get_property(e1,e2,NULL))
- x = true;
- else
- x = false;
+ x = of_property_read_bool(e1,e2);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The drivers don't really need to know which PMIC they're for, so
make a generic binding for them. This alleviates us from updating
the drivers every time a new PMIC comes out. It's still
recommended that we update the binding with new PMIC models and
always specify the specific model for the MPPs and gpios before
the generic compatible string in devicetree, but this at least
cuts down on adding more and more compatible strings to the
drivers until we actually need them.
Cc: <devicetree@vger.kernel.org>
Acked-by: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add the SPDIF mux functionality to the pinctrl for the Allwinner A31
SoC.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add DU pin groups to the R8A7792 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add VIN[0-5] pin groups to the R8A7792 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[geert: Fix VI1_D14_G6_Y6 and VI1_D15_G7_Y7 pins]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This source file handles r8a7795 only, which is not the sole member of
the R-Car Gen3 family.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add CAN0/1 data/clock pin groups to R8A7792 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add SDHI0 pin groups to the R8A7792 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add the EtherAVB pin groups to the R8A7792 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add the PFC support for the R8A7792 SoC including pin groups for some
on-chip devices such as SCIF, INTC, and LBSC...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[geert: s/LSBC/LBSC/]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The PORT_GP_CFG_<n>() macros take up more than 80 columns -- and not for
a good reason. Make the header file checkpatch.pl-proof at least in this
respect...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Implements pull-up and pull-down. On this SoC there is no simple mapping of
GP pins to bias register bits, so we need a table.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.8 kernel cycle.
Nothing stands out as especially exiting: new drivers, new subdrivers,
lots of cleanups and incremental features.
Business as usual.
New drivers:
- New driver for Oxnas pin control and GPIO. This ARM-based chipset
is used in a few storage (NAS) type devices.
- New driver for the MAX77620/MAX20024 pin controller portions.
- New driver for the Intel Merrifield pin controller.
New subdrivers:
- New subdriver for the Qualcomm MDM9615
- New subdriver for the STM32F746 MCU
- New subdriver for the Broadcom NSP SoC.
Cleanups:
- Demodularization of bool compiled-in drivers.
Apart from this there is just regular incremental improvements to a
lot of drivers, especially Uniphier and PFC"
* tag 'pinctrl-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (131 commits)
pinctrl: fix pincontrol definition for marvell
pinctrl: xway: fix typo
Revert "pinctrl: amd: make it explicitly non-modular"
pinctrl: iproc: Add NSP and Stingray GPIO support
pinctrl: Update iProc GPIO DT bindings
pinctrl: bcm: add OF dependencies
pinctrl: ns2: remove redundant dev_err call in ns2_pinmux_probe()
pinctrl: Add STM32F746 MCU support
pinctrl: intel: Protect set wake flow by spin lock
pinctrl: nsp: remove redundant dev_err call in nsp_pinmux_probe()
pinctrl: uniphier: add Ethernet pin-mux settings
sh-pfc: Use PTR_ERR_OR_ZERO() to simplify the code
pinctrl: ns2: fix return value check in ns2_pinmux_probe()
pinctrl: qcom: update DT bindings with ebi2 groups
pinctrl: qcom: establish proper EBI2 pin groups
pinctrl: imx21: Remove the MODULE_DEVICE_TABLE() macro
Documentation: dt: Add new compatible to STM32 pinctrl driver bindings
includes: dt-bindings: Add STM32F746 pinctrl DT bindings
pinctrl: sunxi: fix nand0 function name for sun8i
pinctrl: uniphier: remove pointless pin-mux settings for PH1-LD11
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.8 kernel cycle. The big
news is the completion of the chardev ABI which I'm very happy about
and apart from that it's an ordinary, quite busy cycle. The details
are below.
The patches are tested in linux-next for some time, patches to other
subsystem mostly have ACKs.
I got overly ambitious with configureing lines as input for IRQ lines
but it turns out that some controllers have their interrupt-enable and
input-enabling in orthogonal settings so the assumption that all IRQ
lines are input lines does not hold. Oh well, revert and back to the
drawing board with that.
Core changes:
- The big item is of course the completion of the character device
ABI. It has now replaced and surpassed the former unmaintainable
sysfs ABI: we can now hammer (bitbang) individual lines or sets of
lines and read individual lines or sets of lines from userspace,
and we can also register to listen to GPIO events from userspace.
As a tie-in we have two new tools in tools/gpio: gpio-hammer and
gpio-event-mon that illustrate the proper use of the new ABI. As
someone said: the wild west days of GPIO are now over.
- Continued to remove the pointless ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
Kconfig symbols. I'm patching hexagon, openrisc, powerpc, sh,
unicore, ia64 and microblaze. These are either ACKed by their
maintainers or patched anyways after a grace period and no response
from maintainers.
Some archs (ARM) come in from their trees, and others (x86) are
still not fixed, so I might send a second pull request to root it
out later in this merge window, or just defer to v4.9.
- The GPIO tools are moved to the tools build system.
New drivers:
- New driver for the MAX77620/MAX20024.
- New driver for the Intel Merrifield.
- Enabled PCA953x for the TI PCA9536.
- Enabled PCA953x for the Intel Edison.
- Enabled R8A7792 in the RCAR driver.
Driver improvements:
- The STMPE and F7188x now supports the .get_direction() callback.
- The Xilinx driver supports setting multiple lines at once.
- ACPI support for the Vulcan GPIO controller.
- The MMIO GPIO driver supports device tree probing.
- The Acer One 10 is supported through the _DEP ACPI attribute.
Cleanups:
- A major cleanup of the OF/DT support code. It is way easier to
read and understand now, probably this improves performance too.
- Drop a few redundant .owner assignments.
- Remove CLPS711x boardfile support: we are 100% DT"
* tag 'gpio-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (67 commits)
MAINTAINERS: Add INTEL MERRIFIELD GPIO entry
gpio: dwapb: add missing fwnode_handle_put() in dwapb_gpio_get_pdata()
gpio: merrifield: Protect irq_ack() and gpio_set() by lock
gpio: merrifield: Introduce GPIO driver to support Merrifield
gpio: intel-mid: Make it depend to X86_INTEL_MID
gpio: intel-mid: Sort header block alphabetically
gpio: intel-mid: Remove potentially harmful code
gpio: rcar: add R8A7792 support
gpiolib: remove duplicated include from gpiolib.c
Revert "gpio: convince line to become input in irq helper"
gpiolib: of_find_gpio(): Don't discard errors
gpio: of: Allow overriding the device node
gpio: free handles in fringe cases
gpio: tps65218: Add platform_device_id table
gpio: max77620: get gpio value based on direction
gpio: lynxpoint: avoid potential warning on error path
tools/gpio: add install section
tools/gpio: move to tools buildsystem
gpio: intel-mid: switch to devm_gpiochip_add_data()
gpio: 74x164: Use spi_write() helper instead of open coding
...
|
|
On Marvell mv88f6180 with pin control driver one can not use multi
purpose pins 35 through 44.
I'm using this controller on an embedded board and i found that the
pin multiplexing is not the same as in the hardware spezification.
This patch alters the pin description so that mpp pins 0 to 19 as well
as 35 to 44 are usable.
Pin settings i used can be found here:
http://www.marvell.com/embedded-processors/kirkwood/assets/HW_88F6180_OpenSource.pdf
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A typo in the previous commit to this file needs fixing.
Cc: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 6b4316aecec0 ("pinctrl: xway: Change structure initialisation to c99 style")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This reverts commit b8c2b10a9bc0272a20e096852f8fbbf361749dda.
This patch was in my queue at the same time that a conversion of
the same driver from bool --> tristate was pending and merged.
That is commit 337ea0fb1535 ("pinctrl: Turn AMD support to tristate")
Normally the conflict would show up in the build coverage I do,
however in this case an avoidable instance of linux/module.h in
linux/gpio/driver.h (!) causes the build failure to be masked and
instead the tristate gets built-in even for selected "=m".
In working on removing module.h from driver.h this issue was then
revealed (along with other implicit module.h assumptions in gpio,
and mfd -- which will be fixed separately.)
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
