| Age | Commit message (Collapse) | Author |
|---|
|
Conflicts:
MAINTAINERS
arch/x86/kernel/acpi/boot.c
arch/x86/kernel/acpi/sleep.c
drivers/acpi/Kconfig
drivers/pnp/Makefile
drivers/pnp/quirks.c
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
|
|
According to ACPI spec when the status of some device is not present
but functional, the device is valid and the children of this device
should be enumerated. It means that the device should be added to
linux acpi device tree. But the device driver for this device should not
be loaded.
The detailed info can be found in the section 6.3.7 of ACPI 3.0b spec.
_STA may return bit 0 clear (not present) with bit 3 set (device is
functional). This case is used to indicate a valid device for which no
device driver should be loaded (for example, a bridge device.).
Children of this device may be present and valid. OS should continue
enumeration below a device whose _STA returns this bit combination
http://bugzilla.kernel.org/show_bug.cgi?id=3358
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
CONFIG_PNP_DEBUG is no longer used to turn on dev_dbg() in PNP,
since we have pnp_dbg() which can be enabled at boot-time, so
this patch removes the config option.
Note that pnp_dock_event() checks "#ifdef DEBUG". But there's
never been a clear path for enabling that via configgery. It
happened that CONFIG_PNP_DEBUG enabled it after 1bd17e63a068db6,
but that was accidental and only in 2.6.26.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
pnp_dbg() is equivalent to dev_dbg() except that we can turn it
on at boot-time with the "pnp.debug" kernel parameter, so we don't
have to build a new kernel image.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
There are only a few remaining uses of pnp_info(), so I just
converted them to printk and removed the pnp_err(), pnp_info(),
pnp_warn(), and pnp_dbg() wrappers.
I also removed a couple debug messages that don't seem useful any
more ("driver registered", "driver unregistered", "driver attached").
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Use dev_printk() when possible for more informative error messages.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
We already did that a long time ago for pnp_system_init, but
pnpacpi_init and pnpbios_init remained as subsys_initcalls, and get
linked into the kernel before the arch-specific routines that finalize
the PCI resources (pci_subsys_init).
This means that the PnP routines would either register their resources
before the PCI layer could, or would be unable to check whether a PCI
resource had already been registered. Both are problematic.
I wanted to do this before 2.6.27, but every time we change something
like this, something breaks. That said, _every_ single time we trust
some firmware (like PnP tables) more than we trust the hardware itself
(like PCI probing), the problems have been worse.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The Extended Interrupt descriptor has a producer/consumer bit, but
it's not clear what that would mean, and existing BIOSes use the bit
inconsistently. This patch makes Linux PNPACPI ignore the bit.
The ACPI spec contains examples of PCI Interrupt Link devices marked
as ResourceProducers, but many BIOSes mark them as ResourceConsumers.
I also checked with a Windows contact, who said:
Windows uses only "resource consumer" when dealing with
interrupts. There's no useful way of looking at a resource
producer of interrupts.
... NT-based Windows largely infers the producer/consumer stuff
from the device type and ignores the bits in the namespace. This
was necessary because Windows 98 ignored them and early namespaces
contained random junk.
The reason I want to change this is because if PNPACPI devices exclude
ResourceProducer IRQ resources, we can't write PNP drivers for those
devices.
For example, on machines such as the the HP rx7620, rx7640, rx8620,
rx8640, and Superdome, HPET interrupts are ResourceProducers. The
HPET driver currently has to use acpi_bus_register_driver() and do its
own _CRS parsing, even though it requires absolutely no ACPI-specific
functionality.
It would be better if the HPET driver were a PNP driver and took
advantage of the _CRS parsing built into PNPACPI.
This producer/consumer check was originally added here:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=2b8de5f50e4a302b83ebcd5b0120621336d50bd6
to fix this bug:
http://bugzilla.kernel.org/show_bug.cgi?id=6292
However, the bug was related only to memory and I/O port resources,
where the distinction is sensible and important to Linux. Given that
the distinction is muddled for IRQ resources, I think it was a mistake
to add the check there.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
|
|
The HP CCSR descriptor describes MMIO address space that should appear
as a MEM resource. This patch adds support for parsing these descriptors
in the _CRS data.
The visible effect of this is that these MEM resources will appear
in /sys/devices/pnp0/.../resources, which means that "lspnp -v" will
report it, user applications can use this to locate device CSR space,
and kernel drivers can use the normal PNP resource accessors to
locate them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
|
|
ISAPNP, PNPBIOS, and ACPI describe the "possible resource settings" of
a device, i.e., the possibilities an OS bus driver has when it assigns
I/O port, MMIO, and other resources to the device.
PNP used to maintain this "possible resource setting" information in
one independent option structure and a list of dependent option
structures for each device. Each of these option structures had lists
of I/O, memory, IRQ, and DMA resources, for example:
dev
independent options
ind-io0 -> ind-io1 ...
ind-mem0 -> ind-mem1 ...
...
dependent option set 0
dep0-io0 -> dep0-io1 ...
dep0-mem0 -> dep0-mem1 ...
...
dependent option set 1
dep1-io0 -> dep1-io1 ...
dep1-mem0 -> dep1-mem1 ...
...
...
This data structure was designed for ISAPNP, where the OS configures
device resource settings by writing directly to configuration
registers. The OS can write the registers in arbitrary order much
like it writes PCI BARs.
However, for PNPBIOS and ACPI devices, the OS uses firmware interfaces
that perform device configuration, and it is important to pass the
desired settings to those interfaces in the correct order. The OS
learns the correct order by using firmware interfaces that return the
"current resource settings" and "possible resource settings," but the
option structures above doesn't store the ordering information.
This patch replaces the independent and dependent lists with a single
list of options. For example, a device might have possible resource
settings like this:
dev
options
ind-io0 -> dep0-io0 -> dep1->io0 -> ind-io1 ...
All the possible settings are in the same list, in the order they
come from the firmware "possible resource settings" list. Each entry
is tagged with an independent/dependent flag. Dependent entries also
have a "set number" and an optional priority value. All dependent
entries must be assigned from the same set. For example, the OS can
use all the entries from dependent set 0, or all the entries from
dependent set 1, but it cannot mix entries from set 0 with entries
from set 1.
Prior to this patch PNP didn't keep track of the order of this list,
and it assigned all independent options first, then all dependent
ones. Using the example above, that resulted in a "desired
configuration" list like this:
ind->io0 -> ind->io1 -> depN-io0 ...
instead of the list the firmware expects, which looks like this:
ind->io0 -> depN-io0 -> ind-io1 ...
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
When building resource options, ISAPNP and PNPBIOS set the priority
to something like "0x100 | PNP_RES_PRIORITY_ACCEPTABLE", but we
immediately mask off the 0x100 again in pnp_build_option(), so that
bit looks superfluous.
Thanks to Rene Herman <rene.herman@gmail.com> for pointing this out.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
ACPI Extended Interrupt Descriptors can encode 32-bit interrupt
numbers, so an interrupt number may exceed the size of the bitmap
we use to track possible IRQ settings.
To avoid corrupting memory, complain and ignore too-large interrupt
numbers.
There's similar code in pnpacpi_parse_irq_option(), but I didn't
change that because the small IRQ descriptor can only encode
IRQs 0-15, which do not exceed bitmap size.
In the future, we could handle IRQ numbers greater than PNP_IRQ_NR
by replacing the bitmap with a table or list.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This patch moves all the option allocations (pnp_mem, pnp_port, etc)
into the pnp_register_{mem,port,irq,dma}_resource() functions. This
will make it easier to rework the option data structures.
The non-trivial part of this patch is the IRQ handling. The backends
have to allocate a local pnp_irq_mask_t bitmap, populate it, and pass
a pointer to pnp_register_irq_resource().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This adds a typedef for the IRQ bitmap, which should cause
no functional change, but will make it easier to pass a
pointer to a bitmap to pnp_register_irq_resource().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
PNP previously defined PNP_PORT_FLAG_16BITADDR and PNP_PORT_FLAG_FIXED
in a private header file, but put those flags in struct resource.flags
fields. Better to make them IORESOURCE_IO_* flags like the existing
IRQ, DMA, and MEM flags.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
When we parse a device's _CRS data (the current resource settings),
we should keep track of everything we find, even if it's currently
disabled or invalid.
This is what we already do for ISAPNP and PNPBIOS, and it helps
keep things matched up when we subsequently re-encode resources.
For example, consider a device with (mem, irq0, irq1, io), where
irq0 is disabled. If we drop irq0 when parsing the _CRS, we will
mistakenly put irq1 in the irq0 slot when we encode resources
for an _SRS call.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
|
|
PNP used to have a fixed-size pnp_resource_table for tracking the
resources used by a device. This table often overflowed, so we've
had to increase the table size, which wastes memory because most
devices have very few resources.
This patch replaces the table with a linked list of resources where
the entries are allocated on demand.
This removes messages like these:
pnpacpi: exceeded the max number of IO resources
00:01: too many I/O port resources
References:
http://bugzilla.kernel.org/show_bug.cgi?id=9535
http://bugzilla.kernel.org/show_bug.cgi?id=9740
http://lkml.org/lkml/2007/11/30/110
This patch also changes the way PNP uses the IORESOURCE_UNSET,
IORESOURCE_AUTO, and IORESOURCE_DISABLED flags.
Prior to this patch, the pnp_resource_table entries used the flags
like this:
IORESOURCE_UNSET
This table entry is unused and available for use. When this flag
is set, we shouldn't look at anything else in the resource structure.
This flag is set when a resource table entry is initialized.
IORESOURCE_AUTO
This resource was assigned automatically by pnp_assign_{io,mem,etc}().
This flag is set when a resource table entry is initialized and
cleared whenever we discover a resource setting by reading an ISAPNP
config register, parsing a PNPBIOS resource data stream, parsing an
ACPI _CRS list, or interpreting a sysfs "set" command.
Resources marked IORESOURCE_AUTO are reinitialized and marked as
IORESOURCE_UNSET by pnp_clean_resource_table() in these cases:
- before we attempt to assign resources automatically,
- if we fail to assign resources automatically,
- after disabling a device
IORESOURCE_DISABLED
Set by pnp_assign_{io,mem,etc}() when automatic assignment fails.
Also set by PNPBIOS and PNPACPI for:
- invalid IRQs or GSI registration failures
- invalid DMA channels
- I/O ports above 0x10000
- mem ranges with negative length
After this patch, there is no pnp_resource_table, and the resource list
entries use the flags like this:
IORESOURCE_UNSET
This flag is no longer used in PNP. Instead of keeping
IORESOURCE_UNSET entries in the resource list, we remove
entries from the list and free them.
IORESOURCE_AUTO
No change in meaning: it still means the resource was assigned
automatically by pnp_assign_{port,mem,etc}(), but these functions
now set the bit explicitly.
We still "clean" a device's resource list in the same places,
but rather than reinitializing IORESOURCE_AUTO entries, we
just remove them from the list.
Note that IORESOURCE_AUTO entries are always at the end of the
list, so removing them doesn't reorder other list entries.
This is because non-IORESOURCE_AUTO entries are added by the
ISAPNP, PNPBIOS, or PNPACPI "get resources" methods and by the
sysfs "set" command. In each of these cases, we completely free
the resource list first.
IORESOURCE_DISABLED
In addition to the cases where we used to set this flag, ISAPNP now
adds an IORESOURCE_DISABLED resource when it reads a configuration
register with a "disabled" value.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
|
|
Get rid of a superfluous acpi_pm_device_sleep_state() parameter. The
only legitimate value of that parameter must be derived from the first
parameter, which is what all the callers already do. (However, this
does not address the fact that ACPI still doesn't set up those flags.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
When configuring the resources of an ACPI device, we first evaluate _CRS
to get a template of resource descriptors, then fill in the specific
resource values we want, and finally evaluate _SRS to actually configure
the device.
Some resources have optional fields, so the size of encoded descriptors
varies depending on the specific values. For example, IRQ descriptors can
be either two or three bytes long. The third byte contains triggering
information and can be omitted if the IRQ is edge-triggered and active
high.
The BIOS often assumes that IRQ descriptors in the _SRS buffer use the
same format as those in the _CRS buffer, so this patch enforces that
constraint.
The "Start Dependent Function" descriptor also has an optional byte, but
we don't currently encode those descriptors, so I didn't do anything for
those.
I have tested this patch on a Toshiba Portege 4000. Without the patch,
parport_pc claims the parallel port only if I use "pnpacpi=off". This
patch makes it work with PNPACPI.
This is an extension of a patch by Tom Jaeger:
http://bugzilla.kernel.org/show_bug.cgi?id=9487#c42
References:
http://bugzilla.kernel.org/show_bug.cgi?id=5832 Enabling ACPI Plug and Play in kernels >2.6.9 kills Parallel support
http://bugzilla.kernel.org/show_bug.cgi?id=9487 buggy firmware expects four-byte IRQ resource descriptor (was: Serial port disappears after Suspend on Toshiba R25)
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=1d5b285da1893b90507b081664ac27f1a8a3dc5b related ACPICA fix
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
When we encode IRQ resources, we should use the "shareable" flag we got
from _PRS rather than guessing based on the IRQ trigger mode.
This is based on a patch by Tom Jaeger:
http://bugzilla.kernel.org/show_bug.cgi?id=9487#c32
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
When decoding IRQ trigger mode and polarity, it is not enough to mask by
IORESOURCE_BITS because there are now additional bits defined. For
example, if IORESOURCE_IRQ_SHAREABLE was set, we failed to set *triggering
and *polarity at all.
I can't point to a failure that this patch fixes, but
bugs in this area have caused problems when resuming after
suspend, for example:
http://bugzilla.kernel.org/show_bug.cgi?id=6316
http://bugzilla.kernel.org/show_bug.cgi?id=9487
https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.22/+bug/152187
This is based on a patch by Tom Jaeger:
http://bugzilla.kernel.org/show_bug.cgi?id=9487#c32
[rene.herman@keyaccess.nl: fix comment]
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
|
|
Fix following section mismatch warning:
WARNING: vmlinux.o(.text+0x153d69): Section mismatch in reference from the function is_exclusive_device() to the variable .init.data:excluded_id_list
is_exclusive_device is only used from __init context so document
this with the __init annotation and get rid of the warning.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Move warnings about _CRS and _PRS problems to the place where we
actually make the ACPI calls. Then we don't have to pass around
acpi_status values any more than necessary.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add a pnp_add_mem_resource() that can be used by all the PNP
backends. This consolidates a little more pnp_resource_table
knowledge into one place.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add a pnp_add_io_resource() that can be used by all the PNP
backends. This consolidates a little more pnp_resource_table
knowledge into one place.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add a pnp_add_dma_resource() that can be used by all the PNP
backends. This consolidates a little more pnp_resource_table
knowledge into one place.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add a pnp_add_irq_resource() that can be used by all the PNP
backends. This consolidates a little more pnp_resource_table
knowledge into one place.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This removes a few more references to the pnp_resource_table.
No functional change.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
There are no remaining references to the PNP_MAX_* constants or
the pnp_resource_table structure outside of the PNP core. Make
them private to the PNP core.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This removes more direct references to pnp_resource_table. This
path is used when telling a device what resources it should use.
This doesn't convert ISAPNP because ISA needs to know the config
register index in addition to the resource itself.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Use dev_printk() when possible for more informative error messages.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add pnp_init_resources(struct pnp_dev *) to replace
pnp_init_resource_table(), which takes a pointer to the
pnp_resource_table itself. Passing only the pnp_dev * reduces
the possibility for error in the caller and removes the
pnp_resource_table implementation detail from the interface.
Even though pnp_init_resource_table() is exported, I did not
export pnp_init_resources() because it is used only by the PNP
core.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add debug output to encoders (enabled by CONFIG_PNP_DEBUG). This
uses dev_printk, so I had to add pnp_dev arguments at the same time.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Stop passing around struct pnp_resource_table pointers. In most cases,
the caller doesn't need to know how the resources are stored inside
the struct pnp_dev.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
When we call protocol->get() and protocol->set() methods, we currently
supply pointers to both the pnp_dev and the pnp_resource_table even
though the pnp_resource_table should always be the one associated with
the pnp_dev.
This removes the pnp_resource_table arguments to make it clear that
these methods only operate on the specified pnp_dev.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add debug output to resource option registration functions (enabled
by CONFIG_PNP_DEBUG). This uses dev_printk, so I had to add pnp_dev
arguments at the same time.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Pass the pnp_dev pointer when possible instead of the acpi_handle.
This allows better error messages and reduces the chance of error
in the caller.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This simplifies IRQ resource parsing slightly by computing all the
IORESOURCE_IRQ_* flags at the same time.
This also keeps track of shareability information when parsing options
from _PRS. Previously we ignored shareability in _PRS.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Hoist dma_flags() out of pnpacpi_parse_allocated_dmaresource() into its
caller. This makes pnpacpi_parse_allocated_dmaresource() more similar
to pnpbios_parse_allocated_dmaresource().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
No functional change, just fewer words and fewer chances for
transcription errors.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
pnpacpi_encode_ext_irq() should set resource->data.extended_irq, not
resource->data.irq.
This has been wrong since at least 2.6.12. I haven't seen any bug
reports, but it's clearly incorrect.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Add pnp_alloc_dev() to allocate a struct pnp_dev and fill in the
protocol, instance number, and initial PNP ID. Now it is always
valid to use dev_printk() on any pnp_dev pointer.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
This moves some of the pnp_id knowledge out of the backends and into
the PNP core.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
pnp_add_id() doesn't need to be exposed outside the PNP core, so
move the declaration to an internal header file.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-By: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Keep going and register the device even if we have trouble parsing
_CRS or _PRS. A parsing problem might mean we ignore some resources
the device is using, or we might not be able to change its resources.
But we should still take note of anything we *could* parse correctly.
Also remove reference to dev_id because I plan to remove it soon.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Turn on -DDEBUG in CFLAGS when CONFIG_PNP_DEBUG=y. This makes
dev_dbg() do what you expect.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
IRQ resources 2"
PNP_MAX_IRQ is 2
If a device invokes pnpacpi_parse_allocated_irqresource() 0, 1, or 2 times, we are happy.
The 3rd time, we will fail and print "pnpacpi: exceeded the max number of IRQ resources: 2"
The 4th and subsequent calls (if this ever happened) would silently scribble on
irq_resource[2], which doesn't actualy exist.
Found-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We have been printing these messages at KERN_ERR since 2.6.24,
per http://bugzilla.kernel.org/show_bug.cgi?id=9535
But KERN_ERR pops up on a console booted with "quiet"
and causes users to get alarmed and file bugs
about the message itself:
https://bugzilla.redhat.com/show_bug.cgi?id=436589
So reduce the severity of these messages to
KERN_WARNING, which is not printed by "quiet".
This message will still be seen without "quiet",
but a lot of messages are printed in that mode
and it will be less likely to cause undue alarm.
We could go all the way to KERN_DEBUG, but this
is a real warning after all, so it seems prudent
not to require "debug" to see it.
Signed-off-by: Len Brown <len.brown@intel.com>
|
