| Age | Commit message (Collapse) | Author |
|---|
|
* git://git.infradead.org/users/cbou/battery-2.6.31:
Add ds2782 battery gas gauge driver
olpc_battery: Ensure that the TRICKLE bit is checked
olpc_battery: Fix up eeprom read function
|
|
direct access of driver_data is going away.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds a driver for ds2782 battery devices.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
There are times when the battery is present but trickle charging,
and the EC sets only the TRICKLE bit. So we must check for the bit
when we're checking the charging/present status.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
The eeprom read function was placing values into the wrong place in
'buf'; we were starting from buf[off], rather than buf[0].
Also, the for loop that we were using was much uglier than it needed to
be. This cleans it up a bit.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
There are cases when charging monitor and the event handler try to
change the charger state simultaneously. For instance, a charger is
connected to the system, there's the detection event and the event
handler tries to enable charging. It is possible that the periodic
charging monitor runs at the same time and it still thinks there's
no external charger. So it tries to disable the charging. As the
result, even if the conditions necessary to charge the battery hold,
there will be no actual charging.
The patch changes the event handler so that instead of enabling/
disabling the charger immediately it would rather make the monitor
run. The monitor code then decides what should be the charger state.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
The MAX17040 is a I2C interfaced Fuel Gauge systems for lithium-ion
batteries This patch adds support the MAX17040 Fuel Gauge
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
This adds support for ds2760's sleep mode feature. With this feature
enabled, the chip enters a deep sleep mode and disconnects from the
battery when the w1 line is held down for more than 2 seconds.
This new behaviour can be switched on and off using a new module
parameter.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Acked-by: Matt Reimer <mreimer@vpop.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Removed struct ds2760_platform_data which wasn't defined anywhere.
Indentation cleanups.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Acked-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
* git://git.infradead.org/battery-2.6:
pda_power: Add optional OTG transceiver and voltage regulator support
pcf50633_charger: Remove unused mbc_set_status function
pcf50633_charger: Enable periodic charging restart
|
|
Conflicts:
arch/x86/kernel/cpu/cpufreq/longhaul.c
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
A few comments say "Celcius"; this fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
ACPI has smart batteries, which work in units of energy and measure
rate of (dis)charge as power, thus it is not appropriate to export it
as a current_now. Current_now will still be exported to allow
for userland applications to match.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
The 'battery remaining capacity' calculation in
drivers/power/ds2760_battery.c lacks a parameter check to a division
operation which causes the kernel to oops on my board.
[ 21.233750] Division by zero in kernel.
[ 21.237646] [<c002955c>] (__div0+0x0/0x20) from [<c012561c>] (Ldiv0+0x8/0x10)
[ 21.244816] [<c01bef34>] (ds2760_battery_read_status+0x0/0x2a4) from [<c01bf3a4>] (ds2760_battery_get_property+0x30/0xdc)
[ 21.255803] r8:c03a22c0 r7:c7886100 r6:00000009 r5:c782fe7c r4:c7886084
[ 21.262518] [<c01bf374>] (ds2760_battery_get_property+0x0/0xdc) from [<c01bde98>] (power_supply_show_property+0x48/0x114)
[ 21.273480] r6:c7996000 r5:00000009 r4:00000000
[ 21.278111] [<c01bde50>] (power_supply_show_property+0x0/0x114) from [<c01be158>] (power_supply_uevent+0x188/0x280)
[ 21.288537] r8:00000001 r7:c7886100 r6:c7996000 r5:000000b4 r4:00000000
[ 21.295222] [<c01bdfd0>] (power_supply_uevent+0x0/0x280) from [<c015c664>] (dev_uevent+0xd4/0x10c)
[ 21.304199] [<c015c590>] (dev_uevent+0x0/0x10c) from [<c0128440>] (kobject_uevent_env+0x180/0x390)
[ 21.313170] r5:00000000 r4:c78860ac
[ 21.316725] [<c01282c0>] (kobject_uevent_env+0x0/0x390) from [<c0128664>] (kobject_uevent+0x14/0x18)
[ 21.325850] [<c0128650>] (kobject_uevent+0x0/0x18) from [<c01bdc34>] (power_supply_changed_work+0x5c/0x70)
[ 21.335506] [<c01bdbd8>] (power_supply_changed_work+0x0/0x70) from [<c004d290>] (run_workqueue+0xbc/0x144)
[ 21.345167] r4:c7812040
[ 21.347716] [<c004d1d4>] (run_workqueue+0x0/0x144) from [<c004d94c>] (worker_thread+0xa8/0xbc)
[ 21.356296] r7:c7812040 r6:c7820b00 r5:c782ffa4 r4:c7812048
[ 21.361957] [<c004d8a4>] (worker_thread+0x0/0xbc) from [<c0051008>] (kthread+0x5c/0x94)
[ 21.369971] r7:00000000 r6:c004d8a4 r5:c7812040 r4:c782e000
[ 21.375612] [<c0050fac>] (kthread+0x0/0x94) from [<c00403d0>] (do_exit+0x0/0x688)
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Acked-by: Matt Reimer <mreimer@vpop.net>
Acked-by: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch allows machines to use an OTG transceiver driver instead of
supplying a custom is_usb_online callback to check USB power.
Also, in the case that the OTG transceiver handles charger control when
connected to USB, a regulator named "ac_draw" can be supplied instead of
the custom set_charge callback to control the charger when connected to
AC.
The check for (transceiver->state == OTG_STATE_B_PERIPHERAL) in
otg_is_usb_online is probably too simple, I'm just using this with a
peripheral only device and gpio_vbus + bq24022. I'm not sure which other
OTG states can supply power.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
The 'pcf50633_mbc_set_status' function is unused, so remove it.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
The battery charger state machine switches into charging mode when
the battery voltage falls below 96% of a battery float voltage. But
the voltage drop in Li-ion batteries is marginal(1~2 %) till about
80% of its capacity - which means, after a BATFULL, charging won't
be restarted until 80%.
This work_struct function restarts charging at regular intervals to
make sure the battery doesn't discharge too much.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
container_of(psy, struct pcf50633_mbc, usb); should be
container_of(psy, struct pcf50633_mbc, adapter);
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
IRQF_DISABLED is not guaranteed for shared IRQs. I think power_changed_isr
doesn't need it anyway, as it only fires a timer.
This patch enables IRQF_SAMPLE_RANDOM instead.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
CC: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Driver for battery charger integrated into Dialog Semiconductor DA9030 PMIC
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
Implement support for reporting battery health in the WM8350 battery
interface. Since we are now able to report this via the classs remove
the diagnostics from the interrupt handler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
Some systems are able to report problems with batteries being under
temperature.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
Rather than check for chip revisions in the WM8350 drivers have the core
code set flags for relevant differences.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
This patch adds support for the PMU provided by the WM8350 which
implements battery, line and USB supplies including a battery charger.
The hardware functions largely autonomously, with minimal software
control required to initiate fast charging.
Support for configuration of the USB supply is not yet implemented.
This means that the hardware will remain in the mode configured at
startup, by default limiting the current drawn from USB to 100mA.
This driver was originally written by Liam Girdwood with subsequent
updates for submission by Mark Brown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
|
|
* git://git.infradead.org/battery-2.6:
bq27x00_battery: use unaligned access helper
power_supply: fix dependency of tosa_battery
power_supply: Support for Texas Instruments BQ27200 battery managers
power_supply: Add function to return system-wide power state
pda_power: Check and handle return value of set_irq_wake
|
|
Tejun's commit 7b595756ec1f49e0049a9e01a1298d53a7faaa15 made sysfs
attribute->owner unnecessary. But the field was left in the structure to
ease the merge. It's been over a year since that change and it is now
time to start killing attribute->owner along with its users - one arch at
a time!
This patch is attempt #1 to get rid of attribute->owner only for
CONFIG_X86_64 or CONFIG_X86_32 . We will deal with other arches later on
as and when possible - avr32 will be the next since that is something I
can test. Compile (make allyesconfig / make allmodconfig / custom config)
and boot tested.
akpm: the idea is that we put the declaration of sttribute.owner inside
`#ifndef CONFIG_X86'. But that proved to be too ambitious for now because
new usages kept on turning up in subsystem trees.
[akpm: remove the ifdef for now]
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
drivers/power/Makefile
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
|
|
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: Andres Salomon <dilinger@queued.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now that device_create() has been audited, rename things back to the
original call to be sane.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
It needs the WM97xx touchscreen driver to be compiled in, not as a
module. And it cannot itself be a module, due to some unfortunate
interactions with platform data.
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch adds generic battery driver for wm97xx chips.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Remove hand-rolled get_unaligned_be16, this points to a possible bug as
bq27x00_read does another endian byteswap which sparse notices:
drivers/power/bq27x00_battery.c:81:14: warning: cast to restricted __be16
Which should probably be checked.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
tosa_battery should also depend on wm97xx_ts as it uses dac-accessing
functions from that module.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
These battery managers came in two different packages: one for I2C
busses (BQ27200) and one for HDQ busses (BQ27000).
This driver currently supports only the I2C chip version but the code
is designed in order to easily allow the HDQ chip version integration.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make things static, use kasprintf()]
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Certain drivers benefit from knowing whether the system is on ac or
battery, for instance when determining which backlight registers to
read. This adds a simple call to determine whether there's an online
power supply other than any batteries.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
The recent change in commit 2db873211ba47ef704c301f9ecf4a33413a0b649
forces the calls enable_irq_wake() and disable_irq_wake() to
be balanced. But if in pda_power_suspend() the call to
enable_irq_wake() fails (because attached gpio cannot wake
up the CPU), the corresponding disable_irq_wake will WARN().
Fix it by storing success/failure of enable_irq_wake().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Conflicts:
drivers/power/Kconfig
drivers/power/Makefile
|
|
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf ("platform: prefix MODALIAS
with "platform:"), the platform modalias is prefixed with "platform:".
Add MODULE_ALIAS() to the hotpluggable "power" drivers drivers, to
re-enable auto loading.
[dbrownell@users.sourceforge.net: one was missing]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (85 commits)
[ARM] pxa: add base support for PXA930 Handheld Platform (aka SAAR)
[ARM] pxa: add base support for PXA930 Evaluation Board (aka TavorEVB)
[ARM] pxa: add base support for PXA930 (aka Tavor-P)
[ARM] Update mach-types
[ARM] pxa: make littleton to use the new smc91x platform data
[ARM] pxa: make zylonite to use the new smc91x platform data
[ARM] pxa: make mainstone to use the new smc91x platform data
[ARM] pxa: make lubbock to use new smc91x platform data
[NET] smc91x: prepare SMC_USE_PXA_DMA to be specified in platform data
[NET] smc91x: prepare for SMC_IO_SHIFT to be a platform configurable variable
[NET] smc91x: add SMC91X_NOWAIT flag to platform data
[NET] smc91x: favor the use of SMC91X_USE_* instead of SMC_CAN_USE_*
[NET] smc91x: remove "irq_flags" from "struct smc91x_platdata"
[ARM] 5146/1: pxa2xx: convert all boards to call pxa2xx_transceiver_mode helper
Support for LCD on e740 e750 e400 and e800 e-series PDAs
E-series UDC support
PXA UDC - allow use of inverted GPIO for pullup
Add e350 support
Fix broken e-series build
E-series GPIO / IRQ definitions.
...
|
|
This mirrors the functionality that driver_for_each_device has as well.
We add a start variable, and all callers of the function are fixed up at
the same time.
The block layer will be using this new functionality in a follow-on
patch.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch adds battery monitoring driver for PalmTX.
It can read voltage from the battery and temperature.
It also monitors charging/discharging status.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds common battery interface support for Sharp SL-6000 (tosa).
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
Commit 54d29ad33e3483bcc7ca433a21cf294854e5154a (Power Supply: fix race
in device_create) introduced a race in power_supply_uevent. Previously it
checked that power_supply is available by checking for dev->driver_data.
But now dev->driver_data is set before power_supply->dev is initialised.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
There is a race from when a device is created with device_create() and
then the drvdata is set with a call to dev_set_drvdata() in which a
sysfs file could be open, yet the drvdata will be NULL, causing all
sorts of bad things to happen.
This patch fixes the problem by using the new function,
device_create_drvdata().
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
As Richard Smith pointed out, ACR * 6250 / 15 provides for less
precision loss than ACR * 4167 / 10, _and_ it doesn't overflow. Switch
to using that equation for CHARGE_COUNTER.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: "Richard A. Smith" <richard@laptop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
|
This adds PROP_CHARGE_COUNTER to the power supply class (documenting it
as well). The OLPC battery driver uses this for spitting out its ACR
values (in uAh). We have some rounding errors (the data sheet claims
416.7, the math actually works out to 416.666667, so we're forced to
choose between overflows or precision loss. I chose precision loss,
and stuck w/ data sheet values), but I don't think anyone will care
that much.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
|
