| Age | Commit message (Collapse) | Author |
|---|
|
Currently, ab8500 doesn't set uie_unsupported of rtc_device, while it
doesn't support UIE, see ab8500_rtc_set_alarm().
Thus, when going through rtc_update_irq_enable()->rtc_timer_enqueue(),
there's a chance it has an alarm timer1 queued before which is going to
fired, so this update timer2 will be queued because it isn't the leftmost
one, which means rtc_timer_enqueue() will return 0.
This will result in two problems:
1) UIE EMUL will not be used.
2) When the alarm timer1 is fired, in rtc_timer_do_work() timer2 will
fail to set the alarm time, so this rtc will disfunctional due to
timer2 with the earliest expires in the timerqueue.
So, rtc drivers must set this flag if they don't support UIE.
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Android expects the RTC to have second resolution. On ab8540 cut2 RTC
block has a new register which allows setting seconds for wakeup alarms.
Existing registers (minutes hi, mid and low) have seen their offsets
changed. Here is the new mapping:
* AlarmSec (A) 0x22
* AlarmMinLow (M) from 0x8 to 0x23
* AlarmMinMid (M) from 0x9 to 0x24
* AlarmMinHigh (M) from 0xA to 0x25
Signed-off-by: Julien Delacou <julien.delacou@stericsson.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The driver core clears the driver data to NULL after device_release or
on probe failure, since commit 0998d063100 ("device-core: Ensure drvdata
= NULL when no driver is bound"). Thus, it is not needed to manually
clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
All AB8500 devices are now registered via MFD core, so Device Tree
capability is no longer required for probing. Here we pull the DT
match table to ensure we're no longer probed during Device Tree
start-up.
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: rtc-linux@googlegroups.com
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
AB8500 ED (Early Drop) is no longer supported by the kernel.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
RTC: Fix to correct improper implementation of clock update irq
(RTC_UIE) and enable UIE Emulation.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Ramesh Chandrasekaran <ramesh.chandrasekaran@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Device Tree is enabled
Without this patch, if Device Tree is enabled the AB8500 RTC wouldn't get
probed at all, as there is no reference to it from platform code. This
patch ensures the driver is probed during normal DT start-up.
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This driver's IRQ registration is failing because the kernel now forces
IRQs to be ONESHOT if no IRQ handler is passed.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
|
|
This patch converts the drivers in drivers/rtc/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: John Stultz <john.stultz@linaro.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The rtc_calibration attribute allows user-space to get and set the
AB8500's RtcCalibration register. The AB8500 will then use the value in
this register to compensate for RTC drift every 60 seconds.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Mark Godfrey <mark.godfrey@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The resolution of msleep is related to HZ, so with HZ set to 100 any
msleep of less than 10ms will become ~10ms. This is not what we want.
Use the hrtimer-based usleep_range() and allow for some slack in the
non-critical path so we have more control of what is happening here.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Jonas Aaberg <jonas.aberg@stericsson.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Set can_wake flag so wakealarm property is visible in sysfs.
Signed-off-by: Andrew Lynn <andrew.lynn@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We want this driver to be able to wake up the system.
Signed-off-by: Robert Marklund <robert.marklund@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This moves all the header files related to the abx500 family into
a common include directory below mfd. From now on we place any
subchip header in that directory. Headers previously in e.g.
<linux/mfd/ab8500/gpio.h> get prefixed and are now e.g.
<linux/mfd/abx500/ab8500-gpio.h>. The top-level abstract interface
remains in <linux/mfd/abx500.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch makes the ab8500 mixed signal chip expose the same
interface for register access as the ab3100, ab3550 and ab5500 chip.
The ab8500_read() and ab8500_write() is removed and replaced with
abx500_get_register_interruptible() and
abx500_set_register_interruptible().
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add a driver for the RTC on the AB8500 power management chip. This is a
client of the AB8500 MFD driver.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
