| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Reviewed-by: Karthikeya Sunkesula <Karthikeya.Sunkesula@pmcs.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
As pci_enable_msix() deprecated, replaced with pci_enable_msix_range()
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Reviewed-by: Karthikeya Sunkesula <Karthikeya.Sunkesula@pmcs.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Driver blocks ioctls once it received shutdown/suspend request during
suspend/hybernation. This patch unblocks ioctls on resume path.
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Reviewed-by: Karthikeya Sunkesula <Karthikeya.Sunkesula@pmcs.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Reset irq affinity hints before releasing IRQ.
Removed duplicate code of IRQ acquire/release.
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Reviewed-by: Karthikeya Sunkesula <Karthikeya.Sunkesula@pmcs.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
If 'IsFastPath' bit is set, then response path assumes no error and skips
error check.
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Reviewed-by: Karthikeya Sunkesula <Karthikeya.Sunkesula@pmcs.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
If writeq() not supported, then do atomic two 32bit write
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Reviewed-by: Karthikeya Sunkesula <Karthikeya.Sunkesula@pmcs.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
This change always sets MSI interrupt mode for series-6 controller.
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Reviewed-by: Karthikeya Sunkesula <Karthikeya.Sunkesula@pmcs.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
* .suspend() and .resume() routines implemented in the driver
* aac_release_resources() initiates firmware shutdown
* aac_acquire_resources re-initializes the host interface
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Reviewed-by: Karthikeya Sunkesula <Karthikeya.Sunkesula@pmcs.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Driver sends the right size of the response buffer.
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Reviewed-by: Karthikeya Sunkesula <Karthikeya.Sunkesula@pmcs.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
After getting the platform shutdown command "VM_CloseAll" response from the
firmware, driver was getting configuration IOCTL request from the upper layers
and it sends down to firmware. This causes firmware assert issue.
This patch fixes the firmware assert issue. During the shutdown, if driver
gets commands from the upper layer, driver sends error code to the upper
layers.
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
This patch fixes the IOP_RESET issue. Sending IOP_RESET command need to wait
for only 10 sec instead of 5 minutes in case of firmware does not response
IOP_RESET command. Disable interrupt before setup interrupt routine to
prevent spurious interrupts.
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Also fix up a name truncation problem
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
The Linux aacriad driver fails to detect the case of SG list count=0 on IOCTL
pass-through command and cause intermittent fault. The result is the Linux
aacriad driver send down IOCTL pass-through command with one not initialized
SG list to firmware when receiving SG list count =0 on pass-through command.
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Murthy Bhat <Murthy.Bhat@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Conflicts:
drivers/scsi/scsi_debug.c
Agreed and tested resolution to a merge problem between a fix in scsi_debug
and a driver update
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
SPC-3 defines SERVICE ACTION IN(12) and SERVICE ACTION IN(16).
So rename SERVICE_ACTION_IN to SERVICE_ACTION_IN_16 to be
consistent with SPC and to allow for better distinction.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Tested-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add a use_cmd_list flag in struct Scsi_Host to request keeping track of
all outstanding commands per device.
Default behaviour is not to keep track of cmd_list per sdev, as this may
introduce lock contention. (overhead is more on multi-node NUMA.), and
only enable it on the two drivers that need it.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
It's a NOOP since 2.6.35 and it will be removed one day.
[jejb: remove from missed arm scsi drivers]
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch fixes kernel panic issue while booting into the kdump kernel.
We have triggered crash and kdump vmcore was successful. No issues seen while
booting into the OS.
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Some host adapters do not pass commands through to the target disk
directly. Instead they provide an emulated target which may or may not
accurately report its capabilities. In some cases the physical device
characteristics are reported even when the host adapter is processing
commands on the device's behalf. This can lead to adapter firmware hangs
or excessive I/O errors.
This patch disables WRITE SAME for devices connected to host adapters
that provide an emulated target. Driver writers can disable WRITE SAME
by setting the no_write_same flag in the host adapter template.
[jejb: fix up rejections due to eh_deadline patch]
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
It appears that driver runs into a problem here if fibsize is too small
because we allocate user_srbcmd with fibsize size only but later we
access it until user_srbcmd->sg.count to copy it over to srbcmd.
It is not correct to test (fibsize < sizeof(*user_srbcmd)) because this
structure already includes one sg element and this is not needed for
commands without data. So, we would recommend to add the following
(instead of test for fibsize == 0).
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In commit d496f94d22d1 ('[SCSI] aacraid: fix security weakness') we
added a check on CAP_SYS_RAWIO to the ioctl. The compat ioctls need the
check as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull first round of SCSI updates from James Bottomley:
"The patch set is mostly driver updates (usf, zfcp, lpfc, mpt2sas,
megaraid_sas, bfa, ipr) and a few bug fixes. Also of note is that the
Buslogic driver has been rewritten to a better coding style and 64 bit
support added. We also removed the libsas limitation on 16 bytes for
the command size (currently no drivers make use of this)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (101 commits)
[SCSI] megaraid: minor cut and paste error fixed.
[SCSI] ufshcd-pltfrm: remove unnecessary dma_set_coherent_mask() call
[SCSI] ufs: fix register address in UIC error interrupt handling
[SCSI] ufshcd-pltfrm: add missing empty slot in ufs_of_match[]
[SCSI] ufs: use devres functions for ufshcd
[SCSI] ufs: Fix the response UPIU length setting
[SCSI] ufs: rework link start-up process
[SCSI] ufs: remove version check before IS reg clear
[SCSI] ufs: amend interrupt configuration
[SCSI] ufs: wrap the i/o access operations
[SCSI] storvsc: Update the storage protocol to win8 level
[SCSI] storvsc: Increase the value of scsi timeout for storvsc devices
[SCSI] MAINTAINERS: Add myself as the maintainer for BusLogic SCSI driver
[SCSI] BusLogic: Port driver to 64-bit.
[SCSI] BusLogic: Fix style issues
[SCSI] libiscsi: Added new boot entries in the session sysfs
[SCSI] aacraid: Fix for arrays are going offline in the system. System hangs
[SCSI] ipr: IOA Status Code(IOASC) update
[SCSI] sd: Update WRITE SAME heuristics
[SCSI] fnic: potential dead lock in fnic_is_abts_pending()
...
|
|
Calling kthread_run with a single name parameter causes it to be handled
as a format string. Many callers are passing potentially dynamic string
content, so use "%s" in those cases to avoid any potential accidents.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
One of the customer had reported that the set of raid logical arrays will
become unavailable (I/O offline) after a long hours of IO stress test. The OS
wouldn`t be accessible afterwards and require a hard reset.
This driver patch has a fix for race condition between the doorbell and the
circular buffer. The driver is modified to do an extra read after clearing the
doorbell in case there had been a completion posted during the small timing
window.
With this fix, we ran IO stress for ~13 days. There were no IO failures.
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch adds dual flash firmware support for Series 7 and above controllers.
[thenzl: used ssleep(10) instead udelay]
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Building src.o for a 32 bit system triggers two GCC warnings:
drivers/scsi/aacraid/src.c: In function ‘aac_src_deliver_message’:
drivers/scsi/aacraid/src.c:410:3: warning: right shift count >= width of type [enabled by default]
drivers/scsi/aacraid/src.c:434:2: warning: right shift count >= width of type [enabled by default]
These warnings are caused by a right shift of 32. Use upper_32_bits() to
suppress them.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Mahesh Rajashekhara <Mahesh_Rajashekhara@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Mahesh Rajashekhara <Mahesh_Rajashekhara@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch handles SCSI dma mapping failure case. Reporting error code to the
upper layer instead of BUG_ON().
Signed-off-by: Mahesh Rajashekhara <Mahesh_Rajashekhara@pmc-sierra.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
- Series 7 Async. (performance) mode support added
- New scatter/gather list format for Series 7
- Driver converts s/g list to a firmware suitable list for best performance on
Series 7, this can be disabled with driver parameter "aac_convert_sgl" for
testing purposes
- New container read/write command structure for Series 7
- Fast response support for the SCSI pass-through path added
- Async. status response buffer changes
Signed-off-by: Mahesh Rajashekhara <Mahesh_Rajashekhara@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This may not fix all endian issues in this driver, but it does get the
driver working on PowerPC for a PMC SRC card. So it should at least fix
all the problems in the core and in the SRC support.
[jejb: fix >> 32 breakage reported by Fengguang Wu]
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Acked-by: Achim Leubner <Achim_Leubner@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The loop that waited for syncronous fib commands was causing a CPU stall
when a timeout actually occured.
1) Switch to using a more accurate timeout mechanism.
2) Do not pace the loop with udelay(). Use cpu_relax() to allow for
scheduling to occur.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Acked-by: Achim Leubner <Achim_Leubner@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When an error occured that would shut down the driver, some in-flight
events were getting caught up, deadlocking a CPU or two.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Acked-by: Achim Leubner <Achim_Leubner@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This also stops using the "legacy crap" in Scsi_Host (shost->base is an
unsigned long).
This affected 32-bit systems that have 64-bit resource sizes, causing the
IO address to be truncated.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Acked-by: Achim Leubner <Achim_Leubner@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The patch 116046127d1a3bad2853d02781ad9fee33f05e5a "[SCSI] aacraid: Added
Sync.mode to support series 7/8/9 controllers" removed an iounmap call from
aac_src_ioremap. Before that, the iounmap has been called twice with the same
value (dev->base and dev->regs.src.bar0) and the iounmap complained about it
(iounmap: bad address ...).
The proper solution is a change the paremeter from bar0 to bar1.
Fix this by adding a an iounmap(dev->regs.src.bar1) call.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Achim Leubner <achim_leubner@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Added Sync. mode to support Series 7/8/9 controller families: This is a
compatibility mode for all these controller families. The Async. (Performance)
mode can be changed in the future. First Async. mode version added for Series
7; Controller parameter aac_sync_mode added
Signed-off-by: Mahesh Rajashekhara <aacraid@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
We leak in drivers/scsi/aacraid/commctrl.c::aac_send_raw_srb() :
We allocate memory:
...
struct user_sgmap* usg;
usg = kmalloc(actual_fibsize - sizeof(struct aac_srb)
+ sizeof(struct sgmap), GFP_KERNEL);
and then neglect to free it:
...
for (i = 0; i < usg->count; i++) {
u64 addr;
void* p;
if (usg->sg[i].count >
((dev->adapter_info.options &
AAC_OPT_NEW_COMM) ?
(dev->scsi_host_ptr->max_sectors << 9) :
65536)) {
rcode = -EINVAL;
goto cleanup;
... this 'goto' makes 'usg' go out of scope and leak the memory we
allocated.
Other exits properly kfree(usg), it's just here it is neglected.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
