| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Replace pci_module_init() with pci_register_driver().
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Initial IRQ mask clearing is done by libata-core by freezing all ports
prior to requesting IRQ. Remove redundant IRQ clearing from
init_controller().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
Skip protocol test altogether in spurious interrupt code. If PIOS is received
when it shouldn't, ahci will raise protocol violation.
Signed-off-by: Unicorn Chang <uchang@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: David Wang <touch@sis.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Implement power management support.
Original implementation is from Zhao, Forrest <forrest.zhao@intel.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Zhao, Forrest <forrest.zhao@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Separate out ahci_reset_controller() and ahci_init_controller() from
ata_host_init(). These will be used by PM callbacks. This patch
doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Zhao, Forrest <forrest.zhao@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Implement ahci_[de]init_port() and use it during initialization and
de-initialization. ahci_[de]init_port() are supersets of what used to
be done during driver [de-]initialization. This patch makes the
following behavior changes.
* Per-port IRQ mask is cleared on driver load as done in other
drivers. The mask will be configured properly during probe.
* During init_one(), HOST_IRQ_STAT is cleared after masking port IRQs
such that there is no race window.
* CMD_SPIN_UP is cleared during init_one() instead of being set. It
is set in port_start(). This is more consistent with overall
structure of initialization. Note that CMD_SPIN_UP simply controls
PHY activation.
* Slumber and staggered spin-up are handled properly.
* All init/deinit operations are done in step-by-step manner as
described in the spec instead of issued as single merged command.
Original implementation is from Zhao, Forrest <forrest.zhao@intel.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Zhao, Forrest <forrest.zhao@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Simplify ahci_start_engine() by killing prerequisite condition checks.
Rationales are..
* No user checks error return from ahci_start_engine()
* Code flow guarantees the prerequisite conditions unless the
controller is malfunctioning. In such cases, the driver had chances
to learn about the problem _before_ calling this function.
* Closely related to the above two, driver calls into this function
even when prerequisites fail hoping for the best.
Basically, ahci_start_engine() should only do the operation itself.
It isn't the right place to check for prerequisites.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Zhao, Forrest <forrest.zhao@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* fascist-format comments according to comment style used in libata
core layer.
* if() -> if ()
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Zhao, Forrest <forrest.zhao@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* move ahci_port_start/stop() below EH functions. This makes ahci
more consistent with other drivers and makes prototypes for
ahci_start/stop_engine() unnecessary.
* swap positions between ahci_start_engine() and ahci_stop_engine()
for readability.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Zhao, Forrest <forrest.zhao@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
- Make ahci_start_engine() and ahci_stop_engine() more consistent with
AHCI spec 1.1
- Change their input parameter from ap to port_mmio
- Update the existing users of ahci_start_engine() and ahci_stop_engine()
Signed-off-by: Forrest Zhao <forrest.zhao@intel.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
When we force the chip into dual fn mode so we get PATA and AHCI we must
be sure we don't then do anything dumb like try and grab both with the AHCI
driver.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
ap->flags is way too clamped. Separate out core dynamic flags to
ap->pflags. ATA_FLAG_DISABLED is a dynamic flag but left alone as
it's referenced by a lot of LLDs and it's gonna be removed once all
LLDs are converted to new EH.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Update major version for libata, and several drivers.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
vt8251 chokes on NCQ commands. Two different disks from different
vendors are showing the same symptom and it seems that the windows
driver from via doesn't support NCQ either. Disable NCQ support on
this controller for the time being.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Aalderd Bouwman <boac@wanadoo.nl>
Cc: Bastiaan Jacques <b.jacques@planet.nl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Originally contributed by Justin @ JMicron.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Based on a patch by Andrew Chew @ NVIDIA.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Convert to new probing mechanism and add hotplug support by enabling
PORT_IRQ_PHYRDY, marking ehi for hotplug and scheduling EH on
CONNECT/PHYRDY interrupts.
Unfortunately, ahci cannot reliably wait for the first D2H FIS after
hotplug. It sometimes succeeds but times out more often than not, so
ATA_FLAG_SKIP_D2H_BSY is used.
This patch also fixes ahci_hardreset() such that D2H Register FIS RX
area is cleared before issuing COMRESET. Without this,
ata_busy_sleep() after COMRESET might prematually finish if the
previous TF contains DRDY && !BSY.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Update unload unplug - driver unloading / PCI removal. This is done
by ata_port_detach() which short-circuits EH, disables all devices and
freezes the port. With this patch, EH and unloading/unplugging are
properly synchronized.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Hook transportt->user_scan() and hostt->slave_destroy().
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
With hotplug, every reset might be a probing reset and thus something
similar to probe_init() is needed. prereset() method is called before
a series of resets to a port and is the counterpart of postreset().
prereset() can tell EH to use different type of reset or skip reset by
modifying ehc->i.action.
This patch also implements ata_std_prereset(). Most controllers
should be able to use this function directly or with some wrapping.
After hotplug, different controllers need different actions to resume
the PHY and detect the newly attached device. Controllers can be
categorized as follows.
* Controllers which can wait for the first D2H FIS after hotplug.
Note that if the waiting is implemented by polling TF status, there
needs to be a way to set BSY on PHY status change. It can be
implemented by hardware or with the help of the driver.
* Controllers which can wait for the first D2H FIS after sending
COMRESET. These controllers need to issue COMRESET to wait for the
first FIS. Note that the received D2H FIS could be the first D2H
FIS after POR (power-on-reset) or D2H FIS in response to the
COMRESET. Some controllers use COMRESET as TF status
synchronization point and clear TF automatically (sata_sil).
* Controllers which cannot wait for the first D2H FIS reliably.
Blindly issuing SRST to spinning-up device often results in command
issue failure or timeout, causing extended delay. For these
controllers, ata_std_prereset() explicitly waits ATA_SPINUP_WAIT
(currently 8s) to give newly attached device time to spin up, then
issues reset. Note that failing to getting ready in ATA_SPINUP_WAIT
is not critical. libata will retry. So, the timeout needs to be
long enough to spin up most devices.
LLDDs can tell ata_std_prereset() which of above action is needed with
ATA_FLAG_HRST_TO_RESUME and ATA_FLAG_SKIP_D2H_BSY flags. These flags
are PHY-specific property and will be moved to ata_link later.
While at it, this patch unifies function typedef's such that they all
have named arguments.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Implement NCQ support.
Original implementation is from Jens Axboe.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
With NCQ, there are multiple sg tables, so pp->cmd_tbl_sg doesn't cut
it. Directly calculate sg table address from pp->cmd_tbl.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Add HOST_CAP_NCQ.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
* Rename CMD_TBL_HDR to CMD_TBL_HDR_SZ as it's size not offset.
* Define MAX_CMDS and CMD_SZ and use them in calculation of other
constants.
* Define CMD_TBL_AR_SZ as product of CMD_TBL_SZ and MAX_CMDS, and use
it when calculating PRIV_DMA_SZ.
* CMD_SLOT_SZ is also dependent on MAX_CMDS but hasn't been changed
because I didn't want to change the value used by the original code
(32 commands). Later NCQ change will bump MAX_CMDS to 32 anyway and
the hard coded 32 can be changed to MAX_CMDS then.
* Reorder HOST_CAP_* flags.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
During multiblock PIO, multiple PIOS interrupts are generated before
qc compltion. Current code prints unnecessary message for such cases.
This is exposed when new EH slows down attached device into PIO mode.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Convert AHCI to new EH. Unfortunately, ICH7 AHCI reacts badly if IRQ
mask is diddled during operation. So, freezing is implemented by
unconditionally clearing interrupt conditions while frozen.
* Interrupts are categorized according to required action.
e.g. Connection status or unknown FIS error requires freezing the
port while TF or HBUS_DATA don't.
* Only CONNECT (reflects SErr.X) interrupt is taken into account not
PHYRDY (SErr.N), as CONNECT is better cue for starting EH.
* AHCI may be invoked without any active command. e.g. CONNECT irq
occuring while no qc in progress still triggers EH and will reset
the port and revalidate attached device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Use ATA printk helpers.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Use dev->ap where possible and eliminate superflous @ap from functions
and structures.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Use new SCR and on/offline functions. Note that for LLDD which know
it implements SCR callbacks, SCR functions are guaranteed to succeed
and ata_port_online() == !ata_port_offline().
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
AHCI calls ata_dev_classify() even when no device is attached which
results in false class code. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
|
|
Adds AHCI support for the VIA VT8251.
Includes a workaround for a hardware bug which requires a Command List
Override before softreset.
Signed-off-by: Bastiaan Jacques <b.jacques@planet.nl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Replace ahci_poll_register() with ata_wait_register().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
@verbose was added to ata_reset_fn_t because AHCI complained during
probing if no device was attached to the port. However, muting
failure message isn't the correct approach. Reset methods are
responsible for detecting no device condition and finishing
successfully. Now that AHCI softreset is fixed, kill @verbose.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Conflicts:
drivers/scsi/libata-scsi.c
include/linux/libata.h
|
|
Overriding the whole EH code is a per-transport, not per-host thing.
Move ->eh_strategy_handler to the transport class, same as
->eh_timed_out.
Downside is that scsi_host_alloc can't check for the total lack of EH
anymore, but the transition period from old EH where we needed it is
long gone already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
All softreset methods are responsible for detecting device presence
and succeed softreset in such cases. AHCI didn't use to check for
device presence before proceeding with softreset and this caused
unnecessary reset retrials during probing. This patch adds presence
detection to AHCI softreset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
From: Anatoli Antonovitch <antonovi@ati.com>
Signed-off-by: Felix Kuehling <fkuehlin@ati.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Now that libata is smart enought to handle both soft and hard resets,
add softreset method.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
SCSI midlayer has moved hostt->eh_timed_out to transport template. As
libata doesn't need full-blown transport support yet, implement
minimal transport for libata. No transport class or whatsoever, just
empty transport template with ->eh_timed_out hook.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Turn on AHCI_CMD_PREFETCH for PACKET commands. This hints the
controller that it can prefetch the CDB and the PRD entries. This
patch is originally from Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
|
|
Fix NULL pointer dereference detected by the Coverity checker. Kill
dev -> pdev -> dev conversion while at it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The previous dev->max_sectors patch made sht->max_sectors meaningless.
Kill all initializations of sht->max_sectors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
cdb_len is per-device property. Sharing cdb_len on ap results in
inaccurate configuration on revalidation and hotplugging. This patch
makes cdb_len per-device.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
This patch converts all assert(xxx)'s in low-level drivers to
WARN_ON(!xxx)'s. After this patch, there is no in-kernel user of the
libata assert() macro.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
