| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata ZAC support from Tejun Heo:
"This contains Zone ATA Command support for Shingled Magnetic Recording
devices.
In addition to sending the new commands down to the device, as ZAC
commands depend on getting a lot of responses from the device, piping
up responses is beefed up too. However, it doesn't involve changes to
libata core mechanism or its interaction with upper layers, so I'm not
expecting too many fallouts.
Kudos to Hannes for driving SMR support"
* 'for-4.7-zac' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (28 commits)
libata: support host-aware and host-managed ZAC devices
libata: support device-managed ZAC devices
libata: NCQ encapsulation for ZAC MANAGEMENT OUT
libata: Implement ZBC OUT translation
libata: implement ZBC IN translation
libata: fixup ZAC device disabling
libata-scsi: Generate sense code for disabled devices
libata-trace: decode subcommands
libata: Check log page directory before accessing pages
libata: Add command definitions for NCQ Encapsulation for READ LOG DMA EXT
libata: Separate out ata_dev_config_ncq_send_recv()
libata/libsas: Define ATA_CMD_NCQ_NON_DATA
libsas: enable FPDMA SEND/RECEIVE
libata: do not attempt to retrieve sense code twice
libata-scsi: Set information sense field for invalid parameter
libata-scsi: set bit pointer for sense code information
libata-scsi: Set field pointer in sense code
scsi: add scsi_set_sense_field_pointer()
libata: Implement control mode page to select sense format
libata-scsi: generate correct ATA pass-through sense
...
|
|
Define the NCQ NON DATA command and update libsas to handle it
correctly.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Update libsas and dependent drivers to handle FPDMA
SEND/RECEIVE correctly.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
This patch fix spelling typos found in printk
within various part of the kernel sources.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
SCSI queue for 4.4.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch changes the !blk-mq path to the same defaults as the blk-mq
I/O path by always enabling block tagging, and always using host wide
tags. We've had blk-mq available for a few releases so bugs with
this mode should have been ironed out, and this ensures we get better
coverage of over tagging setup over different configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
commit cff549e4860f ("scsi: proper state checking and module refcount
handling in scsi_device_get") , the reference count of scsi device was
changed, which could lead to when rmmod with at least on drive attached,
SCSI error handle will run into infinite loop, and lockup the system.
Fix it by remove scsi host first, this way scsi core will not send
commands down after detaching SAS transport.
This is a follow up fix for Benjamin's fix for pm80xx.
See also:
http://www.spinics.net/lists/linux-scsi/msg90088.html
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
'0' is now used as the default cmd_per_lun value,
so there's no need to explicitly set it to '1' in the
host template.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree update from Jiri Kosina:
"Usual stuff: documentation updates, printk() fixes, etc"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
intel_ips: fix a type in error message
cpufreq: cpufreq-dt: Move newline to end of error message
ps3rom: fix error return code
treewide: fix typo in printk and Kconfig
ARM: dts: bcm63138: change "interupts" to "interrupts"
Replace mentions of "list_struct" to "list_head"
kernel: trace: fix printk message
scsi: mpt2sas: fix ioctl in comment
zbud, zswap: change module author email
clocksource: Fix 'clcoksource' typo in comment
arm: fix wording of "Crotex" in CONFIG_ARCH_EXYNOS3 help
gpio: msm-v1: make boolean argument more obvious
usb: Fix typo in usb-serial-simple.c
PCI: Fix comment typo 'COMFIG_PM_OPS'
powerpc: Fix comment typo 'CONIFG_8xx'
powerpc: Fix comment typos 'CONFiG_ALTIVEC'
clk: st: Spelling s/stucture/structure/
isci: Spelling s/stucture/structure/
usb: gadget: zero: Spelling s/infrastucture/infrastructure/
treewide: Fix company name in module descriptions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata changes from Tejun Heo:
"The only interesting piece is the support for shingled drives. The
changes in libata layer are minimal. All it does is identifying the
new class of device and report upwards accordingly"
* 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: Remove FIXME comment in atapi_request_sense()
sata_rcar: Document deprecated "renesas,rcar-sata"
sata_rcar: Add clocks to sata_rcar bindings
ahci_sunxi: Make AHCI_HFLAG_NO_PMP flag configurable with a module option
libata-scsi: Update SATL for ZAC drives
libata: Implement ATA_DEV_ZAC
libsas: use ata_dev_classify()
|
|
Since we got rid of ordered tag support in 2010 the prime use case of
switching on and off ordered tags has been obsolete. The other function
of enabling/disabling tagging entirely has only been correctly implemented
by the 53c700 driver and isn't generally useful.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
The task_collector mode (or "latency_injector", (C) Dan Willians) is an
optional I/O path in libsas that queues up scsi commands instead of
directly sending it to the hardware. It generall increases latencies
to in the optiomal case slightly reduce mmio traffic to the hardware.
Only the obsolete aic94xx driver and the mvsas driver allowed to use
it without recompiling the kernel, and most drivers didn't support it
at all.
Remove the giant blob of code to allow better optimizations for scsi-mq
in the future.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
|
|
All drivers use the implementation for ramping the queue up and down, so
instead of overloading the change_queue_depth method call the
implementation diretly if the driver opts into it by setting the
track_queue_depth flag in the host template.
Note that a few drivers validated the new queue depth in their
change_queue_depth method, but as we never go over the queue depth
set during slave_configure or the sysfs file this isn't nessecary
and can safely be removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
|
|
current trivial.git base
|
|
Allow a driver to ask for block layer tags by setting .use_blk_tags in the
host template, in which case it will always see a valid value in
request->tag, similar to the behavior when using blk-mq. This means even
SCSI "untagged" commands will now have a tag, which is especially useful
when using a host-wide tag map.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
|
|
Use the ata device class from libata in libsas instead of checking
the supported command set and switch to using ata_dev_classify()
instead of our own method.
Cc: Tejun Heo <tj@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: James E.J. Bottomley <JBottomley@parallels.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Mostly scripted conversion of the smp_mb__* barriers.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/n/tip-55dhyhocezdw1dg7u19hmh1u@git.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-arch@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The version of isci driver has not been updated for 2 years.
It was 83 isci commits ago. Suspend/resume support has been implemented
and many bugs have been fixed since 1.1. Now update the version to 1.2.
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
isci is needlessly tying libata's hands by returning
SAM_STAT_CHECK_CONDITION to some ata errors. Instead, prefer
SAS_PROTO_RESPONSE to let libata (via sas_ata_task_done()) disposition
the device-to-host fis.
For example isci is triggering an HSM Violation where AHCI is showing a
simple media error for the same bus condition:
isci:
ata7.00: failed command: READ VERIFY SECTOR(S)
ata7.00: cmd 40/00:01:00:00:00/00:00:00:00:00/e0 tag 0
res 01/04:00:00:00:00/00:00:00:00:00/e0 Emask 0x3 (HSM violation)
ahci:
ata6.00: failed command: READ VERIFY SECTOR(S)
ata6.00: cmd 40/00:01:00:00:00/00:00:00:00:00/e0 tag 0
res 51/40:01:00:00:00/00:00:00:00:00/e0 Emask 0x9 (media error)
Note that the isci response matches this from sas_ata_task_done():
/* We saw a SAS error. Send a vague error. */
[..]
dev->sata_dev.fis[3] = 0x04; /* status err */
dev->sata_dev.fis[2] = ATA_ERR;
The end effect is that isci is needlessly triggering hard resets when
they are not necessary.
Reported-by: Xun Ni <xun.ni@intel.com>
Tested-by: Nelson Cheng <nelson.cheng@intel.com>
Acked-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
In the first place, the loop 'for' in the macro 'for_each_isci_host'
(drivers/scsi/isci/host.h:314) is incorrect, because it accesses
the 3rd element of 2 element array. After the 2nd iteration it executes
the instruction:
ihost = to_pci_info(pdev)->hosts[2]
(while the size of the 'hosts' array equals 2) and reads an
out of range element.
In the second place, this loop is incorrectly optimized by GCC v4.8
(see http://marc.info/?l=linux-kernel&m=138998871911336&w=2).
As a result, on platforms with two SCU controllers,
the loop is executed more times than it can be (for i=0,1 and 2).
It causes kernel panic during entering the S3 state
and the following oops after 'rmmod isci':
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff8131360b>] __list_add+0x1b/0xc0
Oops: 0000 [#1] SMP
RIP: 0010:[<ffffffff8131360b>] [<ffffffff8131360b>] __list_add+0x1b/0xc0
Call Trace:
[<ffffffff81661b84>] __mutex_lock_slowpath+0x114/0x1b0
[<ffffffff81661c3f>] mutex_lock+0x1f/0x30
[<ffffffffa03e97cb>] sas_disable_events+0x1b/0x50 [libsas]
[<ffffffffa03e9818>] sas_unregister_ha+0x18/0x60 [libsas]
[<ffffffffa040316e>] isci_unregister+0x1e/0x40 [isci]
[<ffffffffa0403efd>] isci_pci_remove+0x5d/0x100 [isci]
[<ffffffff813391cb>] pci_device_remove+0x3b/0xb0
[<ffffffff813fbf7f>] __device_release_driver+0x7f/0xf0
[<ffffffff813fc8f8>] driver_detach+0xa8/0xb0
[<ffffffff813fbb8b>] bus_remove_driver+0x9b/0x120
[<ffffffff813fcf2c>] driver_unregister+0x2c/0x50
[<ffffffff813381f3>] pci_unregister_driver+0x23/0x80
[<ffffffffa04152f8>] isci_exit+0x10/0x1e [isci]
[<ffffffff810d199b>] SyS_delete_module+0x16b/0x2d0
[<ffffffff81012a21>] ? do_notify_resume+0x61/0xa0
[<ffffffff8166ce29>] system_call_fastpath+0x16/0x1b
The loop has been corrected.
This patch fixes kernel panic during entering the S3 state
and the above oops.
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Reviewed-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Tested-by: Lukasz Dorau <lukasz.dorau@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Remove an erroneous BUG_ON() in the case of a hard reset timeout. The
reset timeout handler puts the port into the "awaiting link-up" state.
The timeout causes the device to be disconnected and we need to be in
the awaiting link-up state to re-connect the port. The BUG_ON() made
the incorrect assumption that resets never timeout and we always
complete the reset in the "resetting" state.
Testing this patch also uncovered that libata continues to attempt to
reset the port long after the driver has torn down the context. Once
the driver has committed to abandoning the link it must indicate to
libata that recovery ends by returning -ENODEV from
->lldd_I_T_nexus_reset().
Cc: <stable@vger.kernel.org>
Acked-by: Lukasz Dorau <lukasz.dorau@intel.com>
Reported-by: David Milburn <dmilburn@redhat.com>
Reported-by: Xun Ni <xun.ni@intel.com>
Tested-by: Xun Ni <xun.ni@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
It seems the "phy_index++;" have been placed in wrong place, without it
the while circle up will do a infinite loop.
Signed-off-by: Xinghai Yu <yuxinghai@cn.fujitsu.com>
Acked-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Oops, apparently no-one I cc'd at intel actually bothered to check this
patch for the isci driver:
commit e73823f7a2c921dcf068d34ea03bd682498d9e42
Author: James Bottomley <JBottomley@Parallels.com>
Date: Tue May 7 15:38:18 2013 -0700
[SCSI] libsas: implement > 16 byte CDB support
sci_swab32_cpy needs multiples of four, so for commands that aren't that, it's
rounding the wrong way. fix by doing (len+3)/4 instead of len/4.
Reported-by: Tony Luck <tony.luck@intel.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This commit fixes a race condition in the isci driver abort task and SSP
device task management path. The race is caused when an I/O termination
in the SCU hardware is necessary because of an SSP target timeout condition,
and the check of the I/O end state races against the HW-termination-driven
end state. The failure of the race meant that no TMF was sent to the device
to clean-up the pending I/O.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Reviewed-by: Lukasz Dorau <lukasz.dorau@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Remove the arbitrary expectation in libsas that all SCSI commands are 16 bytes
or less. Instead do all copies via cmd->cmd_len (and use a pointer to this in
the libsas task instead of a copy). Note that this still doesn't enable > 16
byte CDB support in the underlying drivers because their internal format has
to be fixed and the wire format of > 16 byte CDBs according to the SAS spec is
different. the libsas drivers (isci, aic94xx, mvsas and pm8xxx are all
updated for this change.
Cc: Lukasz Dorau <lukasz.dorau@intel.com>
Cc: Maciej Patelczyk <maciej.patelczyk@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Jack Wang <xjtuwjp@gmail.com>
Cc: Lindar Liu <lindar_liu@usish.com>
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
sas_device_type
These enums have been separate since the dawn of SAS, mainly because the
latter is a procotol only enum and the former includes additional state
for libsas. The dichotomy causes endless confusion about which one you
should use where and leads to pointless warnings like this:
drivers/scsi/mvsas/mv_sas.c: In function 'mvs_update_phyinfo':
drivers/scsi/mvsas/mv_sas.c:1162:34: warning: comparison between 'enum sas_device_type' and 'enum sas_dev_type' [-Wenum-compare]
Fix by eliminating one of them. The one kept is effectively the sas.h
one, but call it sas_device_type and make sure the enums are all
properly namespaced with the SAS_ prefix.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
drivers/scsi/isci/init.c:725:12: warning: 'isci_suspend' defined but not used [-Wunused-function]
drivers/scsi/isci/init.c:743:12: warning: 'isci_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Originally 'efi_enabled' indicated whether a kernel was booted from
EFI firmware. Over time its semantics have changed, and it now
indicates whether or not we are booted on an EFI machine with
bit-native firmware, e.g. 64-bit kernel with 64-bit firmware.
The immediate motivation for this patch is the bug report at,
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
which details how running a platform driver on an EFI machine that is
designed to run under BIOS can cause the machine to become
bricked. Also, the following report,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
details how running said driver can also cause Machine Check
Exceptions. Drivers need a new means of detecting whether they're
running on an EFI machine, as sadly the expression,
if (!efi_enabled)
hasn't been a sufficient condition for quite some time.
Users actually want to query 'efi_enabled' for different reasons -
what they really want access to is the list of available EFI
facilities.
For instance, the x86 reboot code needs to know whether it can invoke
the ResetSystem() function provided by the EFI runtime services, while
the ACPI OSL code wants to know whether the EFI config tables were
mapped successfully. There are also checks in some of the platform
driver code to simply see if they're running on an EFI machine (which
would make it a bad idea to do BIOS-y things).
This patch is a prereq for the samsung-laptop fix patch.
Cc: David Airlie <airlied@linux.ie>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Peter Jones <pjones@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Steve Langasek <steve.langasek@canonical.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Adam Radford <linuxraid@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SATA MICROCODE DOWNALOAD fails on isci driver. After receiving Register
Device to Host (FIS 0x34) frame Initiator resets phy.
In the frame handler routine response (FIS 0x34) was copied into wrong
buffer and upper layer did not receive any answer which resulted in
timeout and reset.
This patch corrects this bug.
Signed-off-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is a large set of updates, mostly for drivers (qla2xxx [including
support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa,
be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).
There's also a rework for tape adding virtually unlimited numbers of
tape drives plus a set of dif fixes for sd and a fix for a live lock
on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI
helper function use in a function that was removed by this pull.
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits)
[SCSI] st: remove st_mutex
[SCSI] sd: Ensure we correctly disable devices with unknown protection type
[SCSI] hpsa: gen8plus Smart Array IDs
[SCSI] qla4xxx: Update driver version to 5.03.00-k1
[SCSI] qla4xxx: Disable generating pause frames for ISP83XX
[SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
[SCSI] qla4xxx: IDC implementation for Loopback
[SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx
[SCSI] qla4xxx: Fix panic while rmmod
[SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
[SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
[SCSI] qla4xxx: Update idc reg in case of PCI AER
[SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
[SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
[SCSI] qla4xxx: Print correct IDC version
[SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
[SCSI] scsi_dh_alua: Enable STPG for unavailable ports
[SCSI] scsi_remove_target: fix softlockup regression on hot remove
[SCSI] ibmvscsi: Fix host config length field overflow
[SCSI] ibmvscsi: Remove backend abstraction
...
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
|
|
We always assign a dummy task context to a port in order to address a
silicon issue. We have 4 ports per controller. So when idle, there are always
exactly 4 TCs "active". The adaptive interrupt coalescing code uses number of
active TCs to figure out the coalescing values. However, we never hit "0" TCs
because of the 4 dummy TCs. Putting in fix so that we calculate this correctly.
Reported-by: Dan Melnic <dan@seamicro.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This commit fixes a driver bug for SSP tasks that require task management
in the target after they complete in the SCU hardware. The problem was
manifested in the function "isci_task_abort_task", which tests
to see if the sas_task.lldd_task is non-NULL before allowing task
management; this bug would always NULL lldd_task in the SCU I/O completion
path even if target management was required, which would prevent
task / target manangement from happening.
Note that in the case of SATA/STP targets, error recovery is provided by
the libata error handler which is why SATA/STP device recovery worked
correctly even though SSP handling did not.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
isci update for 3.6
1/ Fix the workaround for drives that have a slow response to COMSAS.
Drives with this problem intermittently take a long time to be
identified, or fail to be identified altogether.
2/ A minor fix for the efi variable code failure path
3/ A handful of smatch fixups from Dan Carpenter
|
|
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Correct spelling typo within drivers/scsi
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Provide a "simple-dev-pm-ops" implementation that shuts down the domain
and the device on suspend, and resumes the device and the domain on
resume. All of the mechanics of restoring domain connectivity are
handled by libsas once isci has notified libsas that all links should be
back up. libsas is in charge of handling links that did not resume, or
resumed out of order.
Signed-off-by: Artur Wojcik <artur.wojcik@intel.com>
Signed-off-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
...now that the strategy handlers guarantee eh context and notify
the driver of bus reset.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
These are __iomem. Sparse complains if we don't have that.
drivers/scsi/isci/phy.c +149 70: warning:
incorrect type in initializer (different address spaces)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Sparse complains that we redeclare this with a different type, because
in the .c file we use an enum and in the .h file we declare the
parameter as a u32. Probably it's best to use an enum in both places.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The following patch is a fix for the WD workaround
COMSAS negation timeout change. This patch disables the
OOB SM when the OOB is placed in reset, which allows
the updated COMSAS negation timeout value to take
effect.
Cc: Dan Thompson <daniel.j.thompson@intel.com>
Reported-by: Dan Thompson <daniel.j.thompson@intel.com>
Signed-off-by: Dave Maurer <david.c.maurer@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The oem parameter image embedded in the efi variable is at an offset
from the start of the variable. However, in the failure path we try to
free the 'orom' pointer which is only valid when the paramaters are
being read from the legacy option-rom space.
Since failure to load the oem parameters is unlikely and we keep the
memory around in the success case just defer all de-allocation to devm.
Cc: <stable@vger.kernel.org>
Reported-by: Don Morris <don.morris@hp.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
While the RNC is suspended for I/O cleanup, the remote device can be
stopped and the RNC setup for destruction. These changes accomodate that
case in the abort path.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
This fix corrects the saving of resume parameters when the destruction
of the RNC has already been directed, and makes sure not to overwrite
the RNC destruction callbacks.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
