| Age | Commit message (Collapse) | Author |
|---|
|
This patch (as1398b) adds runtime PM support to the SCSI layer. Only
the machanism is provided; use of it is up to the various high-level
drivers, and the patch doesn't change any of them. Except for sg --
the patch expicitly prevents a device from being runtime-suspended
while its sg device file is open.
The implementation is simplistic. In general, hosts and targets are
automatically suspended when all their children are asleep, but for
them the runtime-suspend code doesn't actually do anything. (A host's
runtime PM status is propagated up the device tree, though, so a
runtime-PM-aware lower-level driver could power down the host adapter
hardware at the appropriate times.) There are comments indicating
where a transport class might be notified or some other hooks added.
LUNs are runtime-suspended by calling the drivers' existing suspend
handlers (and likewise for runtime-resume). Somewhat arbitrarily, the
implementation delays for 100 ms before suspending an eligible LUN.
This is because there typically are occasions during bootup when the
same device file is opened and closed several times in quick
succession.
The way this all works is that the SCSI core increments a device's
PM-usage count when it is registered. If a high-level driver does
nothing then the device will not be eligible for runtime-suspend
because of the elevated usage count. If a high-level driver wants to
use runtime PM then it can call scsi_autopm_put_device() in its probe
routine to decrement the usage count and scsi_autopm_get_device() in
its remove routine to restore the original count.
Hosts, targets, and LUNs are not suspended while they are being probed
or removed, or while the error handler is running. In fact, a fairly
large part of the patch consists of code to make sure that things
aren't suspended at such times.
[jejb: fix up compile issues in PM config variations]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] fix race in scsi_target_reap
[SCSI] aacraid: Eliminate use after free
[SCSI] arcmsr: Support HW reset for EH and polling scheme for scsi device
[SCSI] bfa: fix system crash when reading sysfs fc_host statistics
[SCSI] iscsi_tcp: remove sk_sleep check
[SCSI] ipr: improve interrupt service routine performance
[SCSI] ipr: set the data list length in the request control block
[SCSI] ipr: fix a register read to use the correct address for 64 bit adapters
[SCSI] ipr: include the resource path in the IOA status area structure
[SCSI] ipr: implement fixes for 64 bit adapter support
[SCSI] be2iscsi: correct return value in mgmt_invalidate_icds()
|
|
This patch (as1357) fixes a race in SCSI target allocation and
release. Putting a target in the STARGET_DEL state isn't protected by
the host lock, so an old target structure could be reused by a new
device even though it's about to be deleted. The cure is to change
the state while still holding the host lock.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
scsi_scan.c: fix incorrectly formatted kernel-doc notation
& convert documentation of 2 functions into kernel-doc.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch (as1359) fixes a bug in scsi_alloc_target(). After a
device structure has been initialized (and especially after its name
has been set), it must not be freed directly. One has to call
put_device() instead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
* 'for-2.6.34' of git://git.kernel.dk/linux-2.6-block: (38 commits)
block: don't access jiffies when initialising io_context
cfq: remove 8 bytes of padding from cfq_rb_root on 64 bit builds
block: fix for "Consolidate phys_segment and hw_segment limits"
cfq-iosched: quantum check tweak
blktrace: perform cleanup after setup error
blkdev: fix merge_bvec_fn return value checks
cfq-iosched: requests "in flight" vs "in driver" clarification
cciss: Fix problem with scatter gather elements in the scsi half of the driver
cciss: eliminate unnecessary pointer use in cciss scsi code
cciss: do not use void pointer for scsi hba data
cciss: factor out scatter gather chain block mapping code
cciss: fix scatter gather chain block dma direction kludge
cciss: simplify scatter gather code
cciss: factor out scatter gather chain block allocation and freeing
cciss: detect bad alignment of scsi commands at build time
cciss: clarify command list padding calculation
cfq-iosched: rethink seeky detection for SSDs
cfq-iosched: rework seeky detection
block: remove padding from io_context on 64bit builds
block: Consolidate phys_segment and hw_segment limits
...
|
|
The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.
Also introduce a temporary wrapper for backwards compability. This can
be removed after the merge window is closed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
This patch (as1334) fixes a bug in scsi_get_host_dev(). It
incorrectly calls get_device() on the new device's target.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch (as1333) fixes a bug in scsi_report_lun_scan(). If a
newly-allocated device can't be used, it should be deleted.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
|
|
Current FC HBA queue_depth ramp up code depends on last queue
full time. The sdev already has last_queue_full_time field to
track last queue full time but stored value is truncated by
last four bits.
So this patch updates last_queue_full_time without truncating
last 4 bits to store full value and then updates its only
current usages in scsi_track_queue_full to ignore last four bits
to keep current usages same while also use this field
in added ramp up code.
Adds scsi_handle_queue_ramp_up to ramp up queue_depth on
successful completion of IO. The scsi_handle_queue_ramp_up will
do ramp up on all luns of a target, just same as ramp down done
on all luns on a target.
The ramp up is skipped in case the change_queue_depth is not
supported by LLD or already reached to added max_queue_depth.
Updates added max_queue_depth on every new update to default
queue_depth value.
The ramp up is also skipped if lapsed time since either last
queue ramp up or down is less than LLD specified
queue_ramp_up_period.
Adds queue_ramp_up_period to sysfs but only if change_queue_depth
is supported since ramp up and queue_ramp_up_period is needed only
in case change_queue_depth is supported first.
Initializes queue_ramp_up_period to 120HZ jiffies as initial
default value, it is same as used in existing lpfc and qla2xxx.
-v2
Combined all ramp code into this single patch.
-v3
Moves max_queue_depth initialization after slave_configure is
called from after slave_alloc calling done. Also adjusted
max_queue_depth check to skip ramp up if current queue_depth
is >= max_queue_depth.
-v4
Changes sdev->queue_ramp_up_period unit to ms when using sysfs i/f
to store or show its value.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Tested-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
Async scanning introduced a very wide window where the SCSI device is
up and running but has not yet been added to sysfs. We delay the
adding until all scans have completed to retain the same ordering as
sync scanning.
This delay in visibility causes an oops if a device is removed before
we make it visible because the SCSI removal routines have an inbuilt
assumption that if a device is in SDEV_RUNNING state, it must be
visible (which is not necessarily true in the async scanning case).
Fix this by introducing an additional is_visible flag which we can use
to condition the tear down so we do the right thing for running but
not yet made visible.
Reported-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
The root cause of the problem is the fact that dev_set_name() now
allocates storage instead of using the original array within the kobj.
That means that the SCSI assumption that if you haven't made the
containing object or any sub objects visible, you can just destroy it
(and its component devices) lock stock and barrel becomes false.
Fix this by doing the get of sdev_dev at parent time and thus do an
extra put of it in scsi_destroy_sdev() (and all other destruction
without add paths).
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
This patch (as1224) changes the default timeout for INQUIRY commands
from 3 seconds to 20 seconds, which is the value used by Windows for
USB Mass-Storage devices. Some of these devices, like the Corsair
Flash Voyager (see Bugzilla #12188) really do need a long timeout.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch initializes the max_target_blocked field of a scsi target
structure so that a queuecommand return value of
SCSI_MLQUEUE_TARGET_BUSY will actually result in having the
scsi_queue_insert blocking the device queue before requeuing the
command and running the queue. Otherwise, can and does cause livelock
on single CPU configurations if/when open-iSCSI software initiator's
command PDU window fills.
Signed-off-by: Ed Goggin <egoggin@vmware.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
There is currently only one way for userspace to say "wait for my storage
device to get ready for the modules I just loaded": to load the
scsi_wait_scan module. Expectations of userspace are that once this
module is loaded, all the (storage) devices for which the drivers
were loaded before the module load are present.
Now, there are some issues with the implementation, and the async
stuff got caught in the middle of this: The existing code only
waits for the scsy async probing to finish, but it did not take
into account at all that probing might not have begun yet.
(Russell ran into this problem on his computer and the fix works for him)
This patch fixes this more thoroughly than the previous "fix", which
had some bad side effects (namely, for kernel code that wanted to wait for
the scsi scan it would also do an async sync, which would deadlock if you did
it from async context already.. there's a report about that on lkml):
The patch makes the module first wait for all device driver probes, and then it
will wait for the scsi parallel scan to finish.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
- Define the OSD_TYPE scsi device and let it show up in scans
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
We were running i/o and performing a bunch of hba resets in a loop.
This forces a lot of target removes and then rescans. Since the
resets are occuring during scan it's causing the scan i/o to timeout,
invoking error recovery, etc. We end up getting some nasty crashing
in scsi_scan.c due to references to old sdevs that are failing
but had some lingering references that kept them around.
Fix by setting device state to SDEV_DEL if the LLD's slave_alloc
fails.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (45 commits)
[SCSI] qla2xxx: Update version number to 8.03.00-k1.
[SCSI] qla2xxx: Add ISP81XX support.
[SCSI] qla2xxx: Use proper request/response queues with MQ instantiations.
[SCSI] qla2xxx: Correct MQ-chain information retrieval during a firmware dump.
[SCSI] qla2xxx: Collapse EFT/FCE copy procedures during a firmware dump.
[SCSI] qla2xxx: Don't pollute kernel logs with ZIO/RIO status messages.
[SCSI] qla2xxx: Don't fallback to interrupt-polling during re-initialization with MSI-X enabled.
[SCSI] qla2xxx: Remove support for reading/writing HW-event-log.
[SCSI] cxgb3i: add missing include
[SCSI] scsi_lib: fix DID_RESET status problems
[SCSI] fc transport: restore missing dev_loss_tmo callback to LLDD
[SCSI] aha152x_cs: Fix regression that keeps driver from using shared interrupts
[SCSI] sd: Correctly handle 6-byte commands with DIX
[SCSI] sd: DIF: Fix tagging on platforms with signed char
[SCSI] sd: DIF: Show app tag on error
[SCSI] Fix error handling for DIF/DIX
[SCSI] scsi_lib: don't decrement busy counters when inserting commands
[SCSI] libsas: fix test for negative unsigned and typos
[SCSI] a2091, gvp11: kill warn_unused_result warnings
[SCSI] fusion: Move a dereference below a NULL test
...
Fixed up trivial conflict due to moving the async part of sd_probe
around in the async probes vs using dev_set_name() in naming.
|
|
This patch makes part of the scsi probe (which is mostly device spin up and the
partition scan) asynchronous. Only the part that runs after getting the device
number allocated is asynchronous, ensuring that device numbering remains stable.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
|
|
[jejb: limit ioctl to returning 20 characters to avoid overrun
on long device names and add a few more conversions]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch changes scsi_probe_lun() to retry INQUIRY if the device has
not actually sent back any INQUIRY data,
This enables the Thecus N2050 storage device to work better. The
firmware on that device starts up strangely; it sends no data in
response to the initial INQUIRY, and it sends the INQUIRY information
in response to the followup REQUEST SENSE. But after that it works
better, so retrying the INQUIRY is enough to get it going.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
scsi_execute() and scsi_execute_req() discard the residual length
information. Some callers need it. This adds residual argument
(optional) to scsi_execute and scsi_execute_req.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
SCSI-ml manages the queueing limits for the device and host, but
does not do so at the target level. However something something similar
can come in userful when a driver is transitioning a transport object to
the the blocked state, becuase at that time we do not want to queue
io and we do not want the queuecommand to be called again.
The patch adds code similar to the exisiting SCSI_ML_*BUSY handlers.
You can now return SCSI_MLQUEUE_TARGET_BUSY when we hit
a transport level queueing issue like the hw cannot allocate some
resource at the iscsi session/connection level, or the target has temporarily
closed or shrunk the queueing window, or if we are transitioning
to the blocked state.
bnx2i, when they rework their firmware according to netdev
developers requests, will also need to be able to limit queueing at this
level. bnx2i will hook into libiscsi, but will allocate a scsi host per
netdevice/hba, so unlike pure software iscsi/iser which is allocating
a host per session, it cannot set the scsi_host->can_queue and return
SCSI_MLQUEUE_HOST_BUSY to reflect queueing limits on the transport.
The iscsi class/driver can also set a scsi_target->can_queue value which
reflects the max commands the driver/class can support. For iscsi this
reflects the number of commands we can support for each session due to
session/connection hw limits, driver limits, and to also reflect the
session/targets's queueing window.
Changes:
v1 - initial patch.
v2 - Fix scsi_run_queue handling of multiple blocked targets.
Previously we would break from the main loop if a device was added back on
the starved list. We now run over the list and check if any target is
blocked.
v3 - Rediff for scsi-misc.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Brian King <brking@linux.vnet.ibm.com> reported that fibre channel
devices can oops during scanning if their ports block (because the
device goes from CREATED -> BLOCK -> RUNNING rather than CREATED ->
BLOCK -> CREATED).
Fix this by adding a new state: CREATED_BLOCK which can only transition
back to CREATED and disallow the CREATED -> BLOCK transition. Now both
the created and blocked states that the mid-layer recognises can include
CREATED_BLOCK.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The created and blocked states are very shortly going to correspond to
mixed sdev_state states.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
For IBM z series certain LUNs can no longer be accessed.
This is because kernel version 2.6.19 a check was introduced not to
create a generic SCSI device for devices that return PQ=1 and
PDT=0x1f. For WLUNs (see SAM-3, p. 41ff) generic SCSI devices should
be created unconditionally without looking at the PQ bit, so add a
check for WLUNs in with this test.
Acked-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
[jejb: fixed up a ton of missed conversions.
All of you are on notice this has happened, driver trees will now
need to be rebased]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: SCSI List <linux-scsi@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
... when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Make the needlessly global struct scsi_{host,target}_type static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Some drivers have duplicated unlikely() macros. IS_ERR() already has
unlikely() in itself.
This patch cleans up such pointless code.
Signed-off-by: Hirofumi Nakagawa <hnakagawa@miraclelinux.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The current target allocation code registeres each possible target
with sysfs; it will be deleted again if no useable LUN on this target
was found. This results in a string of 'target add/target remove' uevents.
Based on a patch by Hannes Reinecke <hare@suse.de> this patch reworks
the target allocation code so that only uevents for existing targets
are sent. The sysfs registration is split off from the existing
scsi_target_alloc() into a in a new scsi_add_target() function, which
should be called whenever an existing target is found. Only then a
uevent is sent, so we'll be generating events for existing targets
only.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch implements scsi_host and scsi_target device types
and adds both to the scsi_bus.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Fix docbook problem in SCSI source files.
These cause the generated docbook to be incorrect.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While trying to convert the SPI transport class to attribute groups, I
discovered that we don't actually have any transport configure points
for either the target or the host. This patch adds these missing
transport class triggers. The host one is simply done after the add,
the target one tries to be more clever and add it after devices may have
been placed on the target (so the device configure will have set up the
target parameters).
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Some SCSI tape medium changers that need the BLIST_SINGLELUN flag have
the medium changer at one LUN and the tape drive at a different LUN.
The inquiry string of the tape drive may be different from that of the
medium changer. In order for single_lun to be effective, every
scsi_device under a given scsi_target must have it set. This means that
there needs to be a blacklist entry for BOTH the medium changer AND the
tape drive, which is impractical because some medium changers may be
paired with a variety of different tape drive models. It makes more
sense to put the single_lun flag in scsi_target instead of scsi_device,
which causes every device at a given target ID to inherit the single_lun
flag from one LUN. This makes it possible to blacklist just the medium
changer and not the tape drive.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Add Documentation/DocBook/scsi_midlayer.tmpl, add to Makefile, and update
lots of kerneldoc comments in drivers/scsi/*.
Updated with comments from Stefan Richter, Stephen M. Cameron,
James Bottomley and Randy Dunlap.
Signed-off-by: Rob Landley <rob@landley.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Originally based on a patch by Kristen Carlson Accardi @ Intel.
Copious input from James Bottomley.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
If kthread_run failed, we would fail to scan the host, and leak the
allocated async_scan_data. Since using a separate thread is just an
optimisation, do the scan synchronously if we fail to spawn a thread.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
In scsi module I've found some inconsistency between variable type
used in module_param_named and type passed to module_param_named as an
argument. Especially the inconsistency of `max_scsi_luns' parameter is
a bit serious because the description text says "last scsi LUN (should
be between 1 and 2^32-1)".
Signed-off-by: Masatake YAMATO <jet@gyve.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
Stress-testing and some thought has revealed some places where
asynchronous scanning needs some more attention to locking.
- Since async_scan is a bit, we need to hold the host_lock while
modifying it to prevent races against other CPUs modifying the word
that bit is in. This is probably a theoretical race for the moment,
but other patches may change that.
- The async_scan bit means not only that this host is being scanned
asynchronously, but that all the devices attached to this host are not
yet added to sysfs. So we must ensure that this bit is always in sync.
I've chosen to do this with the scan_mutex since it's already acquired
in most of the right places.
- If the host changes state to deleted while we're in the middle of
a scan, we'll end up with some devices on the host's list which must
be deleted. Add a check to scsi_sysfs_add_devices() to ensure the
host is still running.
- To avoid the async_scan bit being protected by three locks, the
async_scan_lock now only protects the scanning_list.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
|
|
This patch tidies up scsi_add_lun a bit. I rewrote the kerneldoc to match
the actual parameters, moved the check for RBC and MMC REPORT_LUN devices
away from the switch(), changed the setup of sdev->type to account for
BLIST_ISROM, moved the check for BLIST_NO_ULD_ATTACH further down in
the function, removed a bogus comment and fixed some whitespace issues.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
When reporting SCSI devices to the SCSI midlayer, use the FCP LUN as
LUN reported to the SCSI layer. With this approach, zfcp does not have
to create unique LUNS, and this code can be removed.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
CONFIG_MODULES=y
CONFIG_SCSI=y
CONFIG_SCSI_SCAN_ASYNC=y
CONFIG_SCSI_WAIT_SCAN=m
2.6.21-rc5-mm2 VFS panics unable to find my root on /dev/sda2, but boots
okay if I change drivers/scsi/Kconfig to "default y" instead of "default m"
for SCSI_WAIT_SCAN.
Make sure there's a late_initcall to scsi_complete_async_scans when it's
built in, so a monolithic SCSI_SCAN_ASYNC kernel can rely on the scans
being completed before trying to mount root, even if they're slow.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
The #ifdef MODULE around the export of scsi_complete_async_scans()
which is the API the scsi_wait_scan module uses is incorrect and
causes the symbol to be undefined in certain circumstances leading to
a build failure. Remove the defines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6:
[SCSI] SCSI core: better initialization for sdev->scsi_level
[SCSI] scsi_proc.c: display sdev->scsi_level correctly
[SCSI] megaraid_sas: update version and author info
[SCSI] megaraid_sas: return sync cache call with success
[SCSI] megaraid_sas: replace pci_alloc_consitent with dma_alloc_coherent in ioctl path
[SCSI] megaraid_sas: add bios_param in scsi_host_template
[SCSI] megaraid_sas: do not process cmds if hw_crit_error is set
[SCSI] scsi_transport.h should include scsi_device.h
[SCSI] aic79xx: remove extra newline from info message
[SCSI] scsi_scan.c: handle bad inquiry responses
[SCSI] aic94xx: tie driver to the major number of the sequencer firmware
[SCSI] lpfc: add PCI error recovery support
[SCSI] megaraid: pci_module_init to pci_register_driver
[SCSI] tgt: fix the user/kernel ring buffer interface
[SCSI] sgiwd93: interfacing to wd33c93
[SCSI] wd33c93: Fast SCSI with WD33C93B
|
|
Globally, s/driverfs/sysfs/g.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
This patch will affect the CDB in INQUIRY commands sent to LUNs above 0
when LUN-0 reports a scsi_level of 0; the LUN bits will no longer be set
in the second byte of the CDB. This is as it should be. Nevertheless,
it's possible that some wacky device might be adversely affected. I doubt
anyone will complain...
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
