| Age | Commit message (Collapse) | Author |
|---|
|
set offload_to_be_enabled to 0 when an ioaccel2 error is processed.
Before, an ioaccel completion error would turn of ioaccel but a rescan
would turn it back on again.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
offload_to_be_enabled also needs to be set to 0 during a state
change.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
faulty drives can cause the driver to hang during a
scan operation.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There have been companies requesting a sysfs entry
to obtain the sas address of device.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver was calling scsi_scan_host before enabling interrupts.
This has gone unnoticed except for customers running in intx mode.
Calling scsi_scan_host before interrupts are enabled causes
"irq XX: nobody cared" messages and the driver to hang.
This patch enables interrupts before the call to scsi_scan_host.
Reported-by: Piotr Karbowski <piotr.karbowski@gmail.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When KDUMP is triggered the driver first talks to the firmware in INTX
mode, but the adapter firmware is still in MSIX mode. Therefore the first
driver command hangs since the driver is waiting for an INTX response and
firmware gives a MSIX response. If when the OS is installed on a RAID
drive created by the adapter KDUMP will hang since the driver does not
receive a response in sync mode.
Fixed by: Change the firmware to INTX mode if it is in MSIX mode before
sending the first sync command.
Cc: stable@vger.kernel.org
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Currently driver completes double completed or spurious interrupted fibs.
This is not necessary and causes the SCSI mid layer to issue aborts and
resets, since completing a fib prematurely might trigger a race condition
resulting in the driver not calling the scsi_done callback.
Fixed by removing the call to fib complete.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Firmware AIF messages about cache loss and data recovery are being missed
by the driver since currently they are not captured but rather let go.
This patch to capture those messages and log them for the user.
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Typically under error conditions, it is possible for aac_command_thread()
to miss the wakeup from kthread_stop() and go back to sleep, causing it
to hang aac_shutdown.
In the observed scenario, the adapter is not functioning correctly and so
aac_fib_send() never completes (or time-outs depending on how it was
called). Shortly after aac_command_thread() starts it performs
aac_fib_send(SendHostTime) which hangs. When aac_probe_one
/aac_get_adapter_info send time outs, kthread_stop is called which breaks
the command thread out of it's hang.
The code will still go back to sleep in schedule_timeout() without
checking kthread_should_stop() so it causes aac_probe_one to hang until
the schedule_timeout() which is 30 minutes.
Fixed by: Adding another kthread_should_stop() before schedule_timeout()
Cc: stable@vger.kernel.org
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As the firmware for series 6, 7, 8 cards does not support msi, remove it
in the driver
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
aac_fib_send has a special function case for initial commands during
driver initialization using wait < 0(pseudo sync mode). In this case,
the command does not sleep but rather spins checking for timeout.This
loop is calls cpu_relax() in an attempt to allow other processes/threads
to use the CPU, but this function does not relinquish the CPU and so the
command will hog the processor. This was observed in a KDUMP
"crashkernel" and that prevented the "command thread" (which is
responsible for completing the command from being timed out) from
starting because it could not get the CPU.
Fixed by replacing "cpu_relax()" call with "schedule()"
Cc: stable@vger.kernel.org
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The adapter has to be started after updating the number of MSIX Vectors
Fixes: ecc479e00db8 (aacraid: Set correct MSIX count for EEH recovery)
Cc: stable@vger.kernel.org
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Suggested-by: Seymour, Shane M <shane.seymour@hpe.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Current driver checks for NULL return from aac_fib_alloc_tag, but it not
possible for it to return NULL.
Fixed by: Remove all the checks for NULL returns from aac_fib_alloc_tag
Suggested-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch fix spelling typos in printk from various part
of the codes.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Some drives set the ILI flag together with MEDIUM ERROR sense code.
Clear the ILI flag in this case so that the medium error will be
handled. The problem was reported by Maurizio Lombardi.
Signed-off-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Remove incorrect lockdep assertion from lpfc_sli_hbqbuf_find() which
acquires the hbalock itself. Fix the comment which resulted in this
mistake.
Fixes: 1c2ba475eb0e ("lpfc: Add lockdep assertions")
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Presumably it isn't possible to have empty lists here, but my static
checker doesn't know that and complains that "ep" can be used
uninitialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This has only called from show_sas_rphy_enclosure_identifier(). The
caller expects that we set an identifier, otherwise it uses an
uninitialized variable.
[mkp: fixed typo]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Firmware events are queued up using the fw_event_work's struct work, not
its delayed_work member. The initial driver for SAS2 controllers had
handled firmware reset using the rescan barrier and was later redesigned
through "mpt2sas: [Resend] Host Reset code cleanup". The delayed_work
variables are now unused and may provoke CONFIG_DEBUG_OBJECTS_TIMERS
"assert_init not available" false warnings in
_scsih_fw_event_cleanup_queue.
Cleanup fw_event_work's unused entries, update its kerneldoc, and
update _scsih_fw_event_cleanup_queue accordingly.
Fixes: 146b16c8071f (mpt3sas: Refcount fw_events and fix unsafe list usage)
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
ip6_route_output looks into different fields in the passed flowi6 structure,
yet cxgbi passes garbage in nearly all those fields. Zero the structure out
first.
Fixes: fc8d0590d9142 ("libcxgbi: Add ipv6 api to driver")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fix spelling typos found in printk
within various part of the kernel sources.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add custom version of function to allocate device,
alloc_dev_quirk_v2_hw(). For sata devices the device id bit0 should be
0.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add v2 hw custom function slot_index_alloc_quirk_v2_hw(). SAS devices
should have IPTT bit0 equal to 1.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add methods to use HW specific versions of functions to allocate slot
and device. HW specific methods are permitted to workaround device id
vs IPTT collision issue in v2 hw.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch will do code optmization for task management functions.
Below are key changes:
1. Remove reset_device hook as it was not being used and driver was
setting this to NULL.
2. Create wrapper functions for task abort and target reset and inside
these functions adapter specific calls be made. e.g. fusion adapters
support task abort and target reset so task abort and target reset
should be issued to fusion adapters only and for MFI adapters, print
a message saying feature not supported.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In OCR path, before calling chip reset calls function
megasas_wait_for_outstanding_fusion to check reason for OCR. In case of
firmware FAULT initiated OCR and DCMD timeout initiated timeout, driver
will clear any outstanding reply (yet to be processed by driver) in
reply queues before going for chip reset. This code is added to handle a
scenario when IO timeout initiated adapter reset and management
application initiated adapter reset (by sending command to FAULT
firmware) happens simultaneously since adapter reset function is
safe-guarded by reset_mutex so only thread will be doing controller
reset. Consider IO timeout thread gets mutex and proceeds with adapter
reset process after disabling interrupts and by the time management
application has fired command to firmware to do adapter reset and the
same command is completed by firmware but since interrupts are disabled,
driver will not get completion and the same command will be in
outstanding/pending commands list of driver and refires same command
from IO timeout thread after chip reset which will again FAULT firmware
and eventually causes kill adapter.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch will reduce memory footprints of megaraid_sas driver when
booted in kdump mode. Driver will not allocate memory for optional and
perfromance oriented features. Below are key changes done in
megaraid_sas driver to do this:
1. Limit Controller's queue depth to 100 in kdump mode.
2. Do not allocate memory for system info buffer and PD info buffer.
3. Disable performance oriented features e.g. Disable RDPQ mode, disable
dual queue depth, restrict to single MSI-x vector.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch avoids that building with W=1 causes gcc to report the
following type of warning:
no previous prototype for ... [-Wmissing-prototypes]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
'struct timeval' will have its tv_sec value overflow on 32-bit systems
in year 2038 and beyond. This patch replaces the use of struct timeval
for computing mpi_request.TimeStamp, and instead uses ktime_t which
provides 64-bit seconds value. The timestamp computed remains
unaffected (milliseconds since Unix epoch).
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
It is unclear what the original intent of the masking was, but it is
clearly incorrect to truncate a physical address before calling
ioremap(). On systems where there are valid physical address bits above
bit-31 (arm64 for example) the result is an eventual OOPs when
initializing the driver.
Remove the bogus code to fix it.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
struct register_host_info stores a 64-bit UTC system time timestamp.
This patch removes the use of 'struct timeval' to obtain that timestamp
as its tv_sec value will overflow on 32-bit systems in year 2038 beyond.
The patch uses ktime_get_real_seconds() which returns a 64-bit seconds value.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch fixes the ITCT table setup as it should be configured
differently for SAS and SATA devices. For SATA disks there is no need
to set qw2 (already zeroed). Also, link parameters for Bus inactive
limit, max connection time limit, and reject to open limit timers
parameters are changed to match global config register,
MAX_CON_TIME_LIMIT_TIME, as recommended by hw team.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch adds support for directly attaching SATA disks to phy
4-8. The problem was that only registers concerned with phy 0-3 were
being considered in sata_int_v2_hw(). The issue was not detected
previously as the development board only exposed phy 0-3; the new board
provides access to 8 phys.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Intermittently it is found that when multiple SATA disks are directly
connected to the host that some disks are not detected. The problem is
that all set bitfields in ENT_INT_SRC1 are cleared for all phys in
sata_int_v2_hw() - it should clear the set bit for the phy being
serviced.
Also unnecessary double-write to ENT_INT_SRC1 and ENT_INT_SRC_MSK1 is
removed (remaining writes are done at end label).
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Contrary to the field name, the MCR (max connection rate) in the ITCT
should hold the device linkrate (linkrate of the connected phy), and not
the max linkrate.
This fixes an issue seen where some SATA drives connected through an
expander which would not attach.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Now it's ready to move the mempool based SG chained allocator code from
SCSI driver to lib/sg_pool.c, which will be compiled only based on a Kconfig
symbol CONFIG_SG_POOL.
SCSI selects CONFIG_SG_POOL.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Rename SCSI_MAX_SG_SEGMENTS to SG_CHUNK_SIZE, which means the amount
we fit into a single scatterlist chunk.
Rename SCSI_MAX_SG_CHAIN_SEGMENTS to SG_MAX_SEGMENTS.
Will move these 2 generic definitions to scatterlist.h later.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Bart Van Assche <bart.vanassche@sandisk.com> (for ib_srp changes)
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Rename SCSI specific struct and functions to more genenic names.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Sagi Grimberg <sgi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Parameter "bool mq" is block driver specific.
Change it to "first_chunk" to make it more generic.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Replace parameter "struct scsi_data_buffer" with "struct sg_table" in
SG alloc/free functions to make them generic.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Claim Marvell 9485 controllers regardless of subdevice ID.
Tested on ASUS P9A-I/C2550/SAS/4L which uses vendor-specific 1043:8635.
[mkp: Tweaked commit message]
Signed-off-by: Leonid Moiseichuk <leonid.moiseichuk@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
the mid-layer.
When we are in connection recovery and the internal command timer on a
request pops, either the scsi_cmnd->device or scsi_cmnd->device->host
back pointers may be NULL as the device that the command that the
request was submitted on may have been subsequently reaped due to the
connection recovery. This can cause one or both of the pointers above to
be NULL and cause a system crash if we try to return the command to the
midlayer.
Instead, double check the pointers before the return to the midlayer so
as to prevent the crash and let the upper layers finish the session
recovery and rediscover the device.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Per customer request, add the following driver tunables:
o devloss_tmo
o max_luns
o queue_depth
o tm_timeout
tm_timeout is set per scsi_host in /sys/class/scsi_host/hostX/tm_timeout.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
