Age | Commit message (Collapse) | Author |
|
The TODO list for the hfi1 driver was completed during 4.6. In addition
other objections raised (which are far beyond what was in the TODO list)
have been addressed as well. It is now time to remove the driver from
staging and into the drivers/infiniband sub-tree.
Reviewed-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The deletion of a cdev is not a fence for holding off references to the
structure. The driver attempts to delete the cdev and then proceeds to
free the parent structure, the hfi1_devdata, or dd. This can potentially
lead to a kernel panic in situations where a user has an FD for the cdev
open, and the pci device gets removed. If the user then closes the FD
there will be a NULL dereference when trying to do put on the cdev's
kobject.
Fix this by pointing the cdev's kobject.parent at a new kobject embedded
in its parent structure. Also take a reference when the device is opened
and put it back when it is closed.
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add a trace message to HFI1s user IOCTL handling. This allows debugging
of which IOCTLs are being handled by the driver.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Remove the write() handler for user space commands now that ioctl
handling is available. User apps will need to change to use ioctl from
this point forward.
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
IOCTL is more suited to what user space commands need to do than the
write() interface. Add IOCTL definitions for all existing write commands
and the handling for those. The write() interface will be removed in a
follow on patch.
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The HFI1_CMD_SDMA_STATUS_UPD command was never implemented it has no
reason to live in the driver. Remove it.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The snoop/diag interface is better served by an implementation which is
more general and usable by other drivers perhaps. Go ahead and remove
the code now and get rid of the char dev. We can put the feature back
when we have a more agreeable solution.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Remove EPROM handling from the cdev which is used for user application
data traffic.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Remove UI char device which exposes direct access to registers for user
space. This was put in to aid in debugging the hardware. We are looking
into alternatives means of providing the same functionality. This
removes another char device from HFI1's footprint.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
hfi1 current exports a cdev that can be used to target all of the hfi's
in the system. However there is a problem with this approach in
that the devices could be on different subnets. This is a problem that
user space can figure out and explicitly tell the driver on which device
to create a context.
Remove the multi-purpose cdev leaving a dedicated cdev for each port.
Also remove the striping capability that is dependent upon the user
choosing the multi-purpose cdev. It is now up to user space to determine
how to stripe contexts.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Remove the usage of an anti-pattern goto in hfi1_cdev_init to improve
code readability.
Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
During the processing of a user SDMA request, if there was an
error before the request counter was increased, the state of
the packet queue could be updated incorrectly, causing the
counter to underflow. As the result, the process could get
stuck later since the counter could never get back to 0.
This patch adds a condition to guard the packet queue update
so that the counter is only decreased if it has been increased
before the error happens.
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This comment was old, the MTU enums have been defined.
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
sdma_event_names[] is only used within CONFIG_SDMA_VERBOSITY ifdefs, so
when CONFIG_SDMA_VERBOSITY is disabled, it results in the following
0-day build warning:
>> drivers/infiniband/hw/hfi1/sdma.c:137:27: warning: 'sdma_event_names'
>> defined but not used [-Wunused-const-variable=]
static const char * const sdma_event_names[] = {
^~~~~~~~~~~~~~~~
This occurs on the following compiler:
compiler: gcc-6 (Debian 6.1.1-1) 6.1.1 20160430
For more information check:
https://lists.01.org/pipermail/kbuild-all/2016-May/020060.html
Fix this warning by defining sdma_event_name[] only within the
CONFIG_SDMA_VERBOSITY ifdefs.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Commit e88c9271d9f8 ("IB/hfi1: Fix buffer cache corner case which
may cause corruption") introduced a bug which may cause a reference
count of a interval RB node to be leaked in the case where an SDMA
transfer from that node completes at the same time as the node is
being extended.
If a node is being extended, it is first removed from the RB tree
in order to be processed without the risk of an invalidation event
removing the node at the same time.
If a SDMA completion happens during that time, the completion handler
will fail to find the node in the RB tree and, therefore, fail to
correctly decrement its refcount. This leaves the node in the tree and
its pages pinned for the duration of the user process.
To prevent this from happening the io vector adds a reference to the
RB node, which is used during the SDMA completion instead of looking
up the node in the RB tree.
This change adds a performance improvement as a side effect by avoiding
the RB tree lookup.
Fixes: e88c9271d9f8 ("IB/hfi1: Fix buffer cache corner case which may cause corruption")
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
It is safe to use RCU_INIT_POINTER() to NULL a pointer, instead of
rcu_assign_pointer().
This results in slightly smaller/faster code.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
If one iteration of the loop causes an error return and a later iteration
doesn't, the later iteration causes the earlier error condition to be
lost. This could result in driver probe succeeding when it should have
failed. Therefore save off the error return in the loop itself rather than
outside the loop.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
SC_USER needs to be the last send context type to ensure other
send context types get their allocation when num_user_contexts
is set to a large number.
This fixes a panic when the module parameter num_user_contexts
is set to 141 and larger.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The handling of the congestion setting MAD packet only
saved off the values, waiting for a congestion control
table packet before going active. Instead, immediately
apply the values.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Remove "IB" keyword from log messages.
Correct comment for thermal sensor init function.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The hfi_rcvhdr tracepoint has the ctxt and eflags switched in the
prototype of the trace event, compared to the args and usage of the
trace function. Fix this by swapping these 2 fields in the trace event
prototype.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
While running perftests, there is a significant utilization of the
random number daemon. This is due to the linux/random.h header being
included in qp.c and verbs.c. However, none of the functions from this
header are being used in these files, so remove the unnecessary header.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The interval RB tree management functions use handlers to
store user-specific callback for the various tree operations.
These handlers are put on a doubly-linked list. When a RB
tree function is called, the list is searched for the handler
of the particular tree.
The list which holds the handlers is modified very rarely - when
a handler is created and when a handler is removed. On the other
hand, it is searched very often. This a perfect usage scenario
for RCU.
The result is a much lower overhead of traversing the list as most
of the time no locking will be required.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The guard is backwards, potentially causing the SDMA client
to panic if a wait structure was not specified.
psm and verbs are not exposed to the issue, but fix the
code just to be correct.
Fixes: a545f5308b6c ("staging/rdma/hfi: fix CQ completion order issue")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The code unconditionlly increments the pio wait counter
making the counter inacurate and unusable.
Fixes: 14553ca11039 ("staging/rdma/hfi1: Adaptive PIO for short messages")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The RESET_N bit of the ASIC_QSFPn_OE register is not used by
the hardware. Remove code that tries to use it - it does
nothing.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The external device configuration was incorrectly shifted to byte 3 of
the 32 bit DC_HOST_COMM_SETTINGS instead of byte 0. This patch corrects
the shift and provides the cable capability information in byte 0.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The function level reset in init_chip() and subsequent write of all 1s
to the ASIC_QSFP registers effectively resets attached active and
optical QSFP modules that pay attention to the RESET_N pin.
We subsequently try to access the QSFP management interface to qualify
and tune the channel and fabric SerDes before enough time (2 seconds
per SFF 8679 spec for QSFP28 modules) has elapsed for the module to
finish initialization. This fails and causes the failure of the channel
tuning algorithm, preventing us from bringing the link up.
This patch checks the port type prior to beginning channel and SerDes
tuning, and if found to be QSFP, watches for the QSFP initialization
complete interrupt, with a maximum timeout of 2 seconds, to allow the
initialization to complete.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
QSFP modules can raise an interrupt to inform us of expected conditions
while the link is down, such as RX power low. Actively ignore these
conditions when the link is down as they only add reporting noise.
Continue reporting conditions that are valid at all times, such as
temperature alarms and warnings.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
hrtimer functions do not guarantee serialization, so we extend the
cca_timer_lock to cover the hrtimer_forward_now() in the hrtimer
callback handler and the hrtimer_start() in process_becn(). This
prevents races between these 2 functions to update the hrtimer state
leading to problems such as:
kernel BUG at kernel/hrtimer.c:1282!
encountered during validation of the CCA feature.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
A MAD directive to start polling must go through the normal
link tuning and start steps in order to correctly handle
active cables.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The code to save the link down reason for reporting to the SMA
was in a location before the actual reason was read. Move the
SMA link down reason assignment to a better location.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The 8051 uses a link down reason to inform the driver why the
link went down. The neighbor planned link down reason code is
only valid when a link down idle message is received by the 8051.
Enhance the explanation on why the link went down.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Versions of the 8051 firmware < 0.38 may report a link failure
as a link downgrade with a width of 0 followed by a link down
notification. Ignore the zero width downgrade notification -
the driver should follow the link down path.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add a receive side mapping rule to extract expected user packets with
the FECN bit set and place them in an eager buffer. This will allow
user libraries to recognize that a FECN was sent when using header
suppression and respond appropriately.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Move the rule setting code into its own routine for improved
searchability and reuse.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The decision to use QOS affects other resource allocation.
Move the QOS decision logic into its own function so it can
be called by other interested parties.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Refactor the allocation, tracking, and writing of the RSM map table
into its own set of routines. This will allow the map table to be
passed to multiple users to fill in as needed. Start with the original
user, QOS.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The pio buffers were pooled evenly among all kernel contexts and
user contexts. However, the demand from kernel contexts is much
lower than user contexts. This patch reduces the allocation for
kernel contexts and thus makes more credits available for PSM,
helping performance. This is especially useful on high core-count
systems where large numbers of contexts are used.
A new context type SC_VL15 is added to distinguish the context used
for VL15 from other kernel contexts. The reason is that VL15 needs
to support 2KB sized packet while other kernel contexts need only
support packets up to the size determined by "piothreshold", which
has a default value of 256.
The new allocation method allows triple buffering of largest pio
packets configured for these contexts. This is sufficient to maintain
verbs performance. The largest pio packet size is 2048B for VL15
and "piothreshold" for other kernel contexts. A cap is applied to
"piothreshold" to avoid excessive buffer allocation.
The special case that SDMA is disable is handled differently. In
that case, the original pooling allocation is used to better
support the much higher pio traffic.
Notice that if adaptive pio is disabled (piothreshold==0), the pio
buffer size doesn't matter for non-VL15 kernel send contexts when
SDMA is enabled because pio is not used at all on these contexts
and thus the new allocation is still valid. If SDMA is disabled then
pooling allocation is used as mentioned in previous paragraph.
Adjustment is also made to the calculation of the credit return
threshold for the kernel contexts. Instead of purely based on
the MTU size, a percentage based threshold is also considered and
the smaller one of the two is chosen. This is necessary to ensure
that with the reduced buffer allocation credits are returned in
time to avoid unnecessary stall in the send path.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mark Debbage <mark.debbage@intel.com>
Reviewed-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Change the default number of user contexts to the number of real
(non-HT) cpu cores in order to reduce the division of hfi1 hardware
contexts in the case of high core counts with hyper-threading enabled.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The awkward coding for setting the allowed_ops field
was tripping an smatch warning.
This patch uses the more appropriate defines from include/rdma
to avoid the issue.
As part of the patch remove a mask that was duplicated
in rdmavt include files and use that mask as appropriate.
Fixes: 8bea6b1cfe6f ("IB/rdmavt: Add create queue pair functionality")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Remove unreachable code from RC ack handling to fix an
smatch error.
Fixes: 633d27399514 ("staging/rdma/hfi1: use mod_timer when appropriate")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The function refresh_qsfp_cache() acquires the i2c chain resource,
but one caller already holds the resource. Change the acquire so
all calls to refresh_qsfp_cache() are covered by the acquire and
remove the acquire within refresh_qsfp_cache().
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The discrete ASIC board design makes the two I2C chains not
independent of each other. That is, only one chain can safely
be accessed at a time. For discrete ASIC devices, adjust the
resource locking so that access to one I2C chain will lock both
of the chains.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The pre-LNI SerDes and channel tuning algorithm already checks for
module presence assertion for the relevant port types. The extraneous
check removed in this patch blocks link up for port types for which
the module presence assertion is not relevant.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Clock and data recovery mechanisms (CDRs) in active QSFP modules
can be turned on or off to improve the bit error rate observed on
the channel. Signal integrity and bit error rate requirements require
us to always turn on any CDRs present in low power cables (power
dissipation 2.5W or lower). However, we adhere to the platform
designer's settings (provided in the platform configuration) for
higher power cables (dissipation 3.5W or higher) if the platform
designer has determined that the platform requires the CDRs to be
turned on (or off) and is capable of supplying and cooling the higher
power modules.
This patch also introduces the get_qsfp_power_class function to
centralize the bit twiddling required to determine the QSFP power class
across the code. Reusing this function improves the readability of code
that depends on knowing the power class of the cable, such as the
active and optical channel tuning algorithm.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add the P_KEY check for user-context mechanism for
both PIO and SDMA. For PIO, the
SendCtxtCheckEnable.DisallowKDETHPackets is set by
default. When the P_KEY is set,
SendCtxtCheckEnable.DisallowKDETHPackets is cleared.
For SDMA, a software check was included. This change
requires user processes to set the P_KEY before sending
any packets, otherwise, the sent packet will fail. The
original submission didn't have this check but it's
required.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mikto Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Increasing the default MTU size to 10KB improves performance
for PSM. Change the default MTU to 10KB but constrain
Verbs MTU to 8KB. Also update default MTU module parameter
description to be HFI1_DEFAULT_MAX_MTU.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Make init_qpmap_table() easier to understand by simplifying
the loop indexing and writing each register when it is "full",
removing the need for a follow-on register write.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The function hdr2sc was using an unshifted mask to obtain
the 5th bit of the service class. Correct the issue by using
the shifted mask.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|