| Age | Commit message (Collapse) | Author |
|---|
|
In chipidea IP RTL, there is a very limited design for siTD, the detail
like below:
There is no Max Packet Size at siTD, so it uses one constant for both
Max Packet Size for packet and the packet size for the last transaction
when considering schedule.
If the ttctrl.ttha does not match against Hub Address field in siTD,
this constant is 188 bytes, else this constant is 1023 bytes.
If the ttctrl.ttha is non-zero value, RTL will use 188 as this constant,
so it will lose the data if the packet size is larger than 188 bytes, eg,
if we playback a wav which format is 48khz, 16 bits, 2 channels, the
packet size will be 192bytes, but the controller will only send 188 bytes
for this packet, the noise will be heared using USB audio card.
The use case is single transaction, but higher frame rate.
If the ttctr.ttha is zero value, we can send 1023 bytes within one
transaction, but the controller will not accept the coming tranaction
if it considers the schedule time is less than 1023 bytes. So the
limitation is we can't schedule as many as transactions within frame.
If the total bytes is already 256 bytes for previous transactions within
frame, it can't accept another transaction. The use case is multiple
transactions, but less frame rate.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
call to of_find_property() before of_property_read_u32() is unnecessary.
of_property_read_u32() anyway calls to of_find_property() only.
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
Since this configuration option has deleted, cleans up all
its references.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
|
|
Since we need to mount debugfs to show/store the things we
want to debug, it is duplicated to add another configuration
to enable it. Meanwhile, with CONFIG_USB_CHIPIDEA_DEBUG,
we can't support chipidea debugfs at runtime.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: Jun Li <jun.li@freescale.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
USB Chipidea updates for v4.4-rc1
- Use extcon framework for VBUS and ID detect
- Add imx6sx and imx7d support
- Other small changes
|
|
Add support for the optional 'phy-clkgate-delay-us' property that is
used to describe the delay time between putting PHY into low power mode
and turning off the PHY clock.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
On recent Qualcomm platforms VBUS and ID lines are not routed to
USB PHY LINK controller. Use extcon framework to receive connect
and disconnect ID and VBUS notification.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
USB: chipidea updates for v4.3-rc1
The main changes are adding several system interfaces for
tuning performance, and each vendors can adjust them according
to their design configurations.
Others are tiny improvements, like more well siTD supports,
USB_DEVICE_A_HNP_SUPPORT supports, etc.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.3 merge window
New support for Allwinne SoC on the MUSB driver has been added to the list of
glue layers. MUSB also got support for building all DMA engines in one binary;
this will be great for distros.
DWC3 now has no trace of dev_dbg()/dev_vdbg() usage. We will rely solely on
tracing to debug DWC3. There was also a fix for memory corruption with EP0 when
maxpacket size transfers are > 512 bytes.
Robert's EP capabilities flags is making EP selection a lot simpler. UDCs are
now required to set these flags up when adding endpoints to the framework.
Other than these, we have the usual set of miscelaneous cleanups and minor
fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The user can adjust it through dts or platform data
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
The users can change it through dts or platform data if they
want to change the default value.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
The system bus and chipidea IP have different limitations for
both host and device mode.
For example, with below errata, we need to enable SDIS(Stream Disable
Mode) at host mode. But we don't want it for device mode at the
same system.
TAR 9000378958
Title: Non-Double Word Aligned Buffer Address Sometimes Causes Host to
Hang on OUT Retry
Impacted Configuration: Host mode, all transfer types
Description:
The host core operating in streaming mode may under run while sending
the data packet of an OUT transaction. This under run can occur if
there are unexpected system delays in fetching the remaining packet
data from memory. The host forces a bad CRC on the packet, the device
detects the error and discards the packet. The host then retries a Bulk,
Interrupt, or Control transfer if an under run occurs according to the
USB specification. During simulations, it was found that the host does
not issue the retry of the failed bulk OUT. It does not issue any other
transactions except SOF packets that have incorrect frame numbers.
The second failure mode occurs if the under run occurs on an ISO OUT
transaction and the next ISO transaction is a zero byte packet. The host
does not issue any transactions (including SOFs). The device detects a
Suspend condition, reverts to full speed, and waits for resume signaling.
A third failure mode occurs when the host under runs on an ISO OUT and
the next ISO in the schedule is an ISO OUT with two max packets of 1024
bytes each. The host should issue MDATA for the first OUT followed by
DATA1 for the second. However, it drops the MDATA transaction, and
issues the DATA1 transaction.
The system impact of this bug is the same regardless of the failure mode
observed. The host core hangs, the ehci_ctrl state machine waits for the
protocol engine to send the completion status for the corrupted
transaction, which never occurs. No indication is sent to the host
controller driver, no register bits change and no interrupts occur.
Eventually the requesting application times out.
Detailed internal behavior:
The EHCI control state machine (ehci_ctrl) in the DMA block is responsible
for parsing the schedules and initiating all transactions. The ehci_ctrl
state machine passes the transaction details to the protocol block by
writing the transaction information in to the TxFIFO. It then asserts
the pe_hst_run_pkt signal to inform the host protocol state machine
(pe_hst_state) that there is a packet in the TxFIFO.
A tag of 0x0 indicates a start of packet with the data providing the
following information:
35:32 Tag
31:30 Reserved
29:23 Endpoint (lowest 4 bits)
22:16 Address
15:10 Reserved
9:8 Endpoint speed
7:6 Endpoint type
5:6 Data Toggle
3:0 PID
The pe_hst_state reads the packet information and constructs the packet
and issues it to the PHY interface.
The ehci_ctrl state machine writes the start transaction information in
to the TxFIFO as 0x03002910c for the OUT packet that had the under run
error. However, it writes 0xC3002910C for the retry of the Out
transaction, which is incorrect.
The pe_hst_state enters a bus timeout state after sending the bad CRC
for the packet that under ran. It then purges any data that was back
filled in to the TxFIFO for the packet that under ran. The pe_hst_state
machine stops purging the TxFIFO when it is empty or if it reads a
location that has a tag of 0x0, indicating a start of packet command.
The pe_hst_state reads 0xC3002910C and discards it as it does not decode
to a start of packet command. It continues to purge the OUT data that
has been pre-buffered for the OUT retry . The pe_hst_state detects the
hst_packet_run signal and attempts to read the PID and address
information from the TxFIFO. This location has packet data and so does
not decode to a valid PID and so falls through to the PE_HST_SOF_LOAD
state where the frame_num_counter is updated. The frame_num_counter
is updated with the data in the TxFIFO. In this case, the data is
incorrect as the ehci_ctrl state machine did not initiate the load.
The hst_pe_state machine detects the SOF request signal and sends an
SOF with the bad frame number. Meanwhile, the ehci_ctrl state machine
waits indefinitely in the run_pkt state waiting for the completion
status from pe_hst_state machine, which will never happen.
The ISO failure case is similar except that there is no retry for ISO.
The ehci_ctrl state machine moves to the next transfer in the periodic
schedule. If the under run occurs on the last entry of the periodic
list then it moves to the Async schedule.
In the case of ISO OUT simulations, the next ISO is a zero byte OUT
and again the start of packet command gets corrupted. The TxFIFO is
empty when the hst_pe_state attempts to read the Address and PID
information as the transaction is a zero byte packet. This results
in the hst_pe_state machine staying in the GET_PID state, which means
that it does not issue any transactions (including SOFs). The device
detects a Suspend condition and reverts to full speed mode and waits
for a Resume or Reset signal.
The EHCI specification allows a Non-DoubleWord (32 bits) offset to
be used as a current offset for Buffer Pointer Page 0 of the qTD.
In Non-DoubleWord aligned cases, the core reads the packet data
from the AHB memory, performs the alignment operation before writing
it in to the TxFIFO as a 32 bit data word. An End Of Packet tag (EOP)
is written to the TxFIFO after all the packet data has been written
in to the TxFIFO. The alignment function is reset to Idle by the EOP
tag. The corruption of the start of packet command arises because the
packet buffer for the OUT transaction that under ran is not aligned
to a DoubleWord, and hence no EOP tag is written to the TxFIFO. The
alignment function is still active when the start packet information
is written in to the TxFIFO for the retry of the bulk packet or for
the next transaction in the case of an under run on an ISO. This
results in the corruption of the start tag and the transaction
information.
Click for waveform showing the command 0x 0000300291 being written in
to the TX FIFO for the Out that under ran.
Click for waveform showing the command 0xC3002910C written to the
TxFIFO instead of 0x 0000300291
Versions affected: Versions 2.10a and previous versions
How discovered: Customer simulation
Workaround:
1- The EHCI specification allows a non-DoubleWord offset to be used
as a current offset for Buffer Pointer Page 0 of the qTD. However,
if a DoubleWord offset is used then this issue does not arise.
2- Use non streaming mode to eliminate under runs.
Resolution:
The fix involves changes to the traffic state machine in the
vusb_hs_dma_traf block. The ehci_ctrl state machine updates the context
information by encoding the transaction results on the
hst_op_context_update signals at the end of a transaction. The signal
hst_op_context_update is added to the traffic state machine, and the
tx_fifo_under_ran_r signal is generated if the transaction results in
an under run error. Click for waveform
The traffic state machine then traverses to the do_eop states if the
tx_fifo_under_ran error is asserted. Thus an EOP tag is written in to
the TxFIFO as shown in this waveform .
The EOP tag resets the align state machine to the Idle state ensuring
that the next command written by the echi_ctrl state machine does not
get corrupted.
File(s) modified:
RTL code fixed: …..
Method of reproducing: This failure cannot be reproduced in the current
test bench.
Date Found: March 2010
Date Fixed: June 2010
Update information:
Added the RTL code fix
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
This makes the function hw_alloc_repmap be declared to have a return
type of void now due to this particular function never returning
a error code to its caller due to this function always running
successfully to completion nor it's caller putting the return
value into a variable in order to check if a error code is passed
from the function hw_alloc_repmap when calling this function.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
|
|
ITC (Interrupt Threshold Control) is used to set the maximum rate at which
the host/device controller will issue interrupts. The default value is 8 (1ms)
for it. EHCI core will modify it to 1, but device mode keeps it as default
value.
In some use cases like Android ADB, it only has one usb request for each
direction, and maximum payload data is only 4KB, so the speed is 4MB/s
at most, it needs controller to trigger interrupt as fast as possible
to increase the speed. The USB performance will be better if the interrupt
can be triggered faster.
Reduce ITC value is benefit for USB performance, but the interrupt number
is increased at the same time, it may increase cpu utilization too.
Most of use case cares about performance, but some may care about
cpu utilization, so, we leave a platform interface for user.
We set ITC as 1 (1 micro-frame) as default value which is aligned
with ehci core default value.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
It is used to configure controller parameters according to
platform data, like speed, stream mode, etc, both host and
device's initialization need it, most of code are the
same for both roles, with this new interface, it can reduce
the duplicated code and be easy to maintain in future.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
The register of ttctrl.ttha describes like below:
- Internal TT Hub Address Representation
- RW
- Default = 0000000b
This field is used to match against the Hub Address field in QH & siTD
to determine if the packet is routed to the internal TT for directly
attached FS/LS devices. If the Hub Address in the QH or siTD does not
match this address then the packet will be broadcast on the High Speed
ports destined for a downstream High Speed hub with the address in the QH/siTD.
In silicon RTL, this entry only affects QH and siTD, and the hub.addr at
both QH and siTD are 0 in ehci core for chipidea (with hcd->has_tt = 1).
So, for QH, if the "usage_tt" flag at RTL is 0, set CI_HDRC_SET_NON_ZERO_TTHA
will not affect QH (with non-hs device); for siTD, set this flag
will change remaining space requirement for the last transaction from 1023
bytes to 188 bytes, it can increase the number of transactions within one
frame, ehci periodic schedule code will not queue the packet if the frame space
is full, so it is safe to set this flag for siTD.
With this flag, it can fix the problem Alan Stern reported below:
http://www.spinics.net/lists/linux-usb/msg123125.html
And may fix Michael Tessier's problem too.
http://www.spinics.net/lists/linux-usb/msg118679.html
CC: stern@rowland.harvard.edu
CC: michael.tessier@axiontech.ca
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
Init and update otg capabilities by DT, set gadget's otg capabilities
accordingly.
Acked-by: Peter Chen <peter.chen@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The ehci_init_driver is used to initialize hcd APIs for each
ehci controller driver, it is designed to be called only one time
and before driver register is called. The current design will
cause ehci_init_driver is called multiple times at probe process,
it will cause hc_driver's initialization affect current running hcd.
We run out NULL pointer dereference problem when one hcd is started
by module_init, and the other is started by otg thread at SMP platform.
The reason for this problem is ehci_init_driver will do memory copy
for current uniform hc_driver, and this memory copy will do memset (as 0)
first, so when the first hcd is running usb_add_hcd, and the second
hcd may clear the uniform hc_driver's space (at ehci_init_driver),
then the first hcd will meet NULL pointer at the same time.
See below two logs:
LOG_1:
ci_hdrc ci_hdrc.0: EHCI Host Controller
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.1: doesn't support gadget
Unable to handle kernel NULL pointer dereference at virtual address 00000014
pgd = 80004000
[00000014] *pgd=00000000
Internal error: Oops: 805 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 108 Comm: kworker/u8:2 Not tainted 3.14.38-222193-g24b2734-dirty #25
Workqueue: ci_otg ci_otg_work
task: d839ec00 ti: d8400000 task.ti: d8400000
PC is at ehci_run+0x4c/0x284
LR is at _raw_spin_unlock_irqrestore+0x28/0x54
pc : [<8041f9a0>] lr : [<8070ea84>] psr: 60000113
sp : d8401e30 ip : 00000000 fp : d8004400
r10: 00000001 r9 : 00000001 r8 : 00000000
r7 : 00000000 r6 : d8419940 r5 : 80dd24c0 r4 : d8419800
r3 : 8001d060 r2 : 00000000 r1 : 00000001 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7d Table: 1000404a DAC: 00000015
Process kworker/u8:2 (pid: 108, stack limit = 0xd8400238)
Stack: (0xd8401e30 to 0xd8402000)
1e20: d87523c0 d8401e48 66667562 d8419800
1e40: 00000000 00000000 d8419800 00000000 00000000 00000000 d84198b0 8040fcdc
1e60: 00000000 80dd320c d8477610 d8419c00 d803d010 d8419800 00000000 00000000
1e80: d8004400 00000000 d8400008 80431494 80431374 d803d100 d803d010 d803d1ac
1ea0: 00000000 80432428 804323d4 d803d100 00000001 80435eb8 80e0d0bc d803d100
1ec0: 00000006 80436458 00000000 d803d100 80e92ec8 80436f44 d803d010 d803d100
1ee0: d83fde00 8043292c d8752710 d803d1f4 d803d010 8042ddfc 8042ddb8 d83f3b00
1f00: d803d1f4 80042b60 00000000 00000003 00000001 00000001 80054598 d83f3b00
1f20: d8004400 d83f3b18 d8004414 d8400000 80e3957b 00000089 d8004400 80043814
1f40: d839ec00 00000000 d83fcd80 d83f3b00 800436e4 00000000 00000000 00000000
1f60: 00000000 80048f34 00000000 00000000 00000000 d83f3b00 00000000 00000000
1f80: d8401f80 d8401f80 00000000 00000000 d8401f90 d8401f90 d8401fac d83fcd80
1fa0: 80048e68 00000000 00000000 8000e538 00000000 00000000 00000000 00000000
1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<8041f9a0>] (ehci_run) from [<8040fcdc>] (usb_add_hcd+0x248/0x6e8)
[<8040fcdc>] (usb_add_hcd) from [<80431494>] (host_start+0x120/0x2e4)
[<80431494>] (host_start) from [<80432428>] (ci_otg_start_host+0x54/0xbc)
[<80432428>] (ci_otg_start_host) from [<80435eb8>] (otg_set_protocol+0xa4/0xd0)
[<80435eb8>] (otg_set_protocol) from [<80436458>] (otg_set_state+0x574/0xc58)
[<80436458>] (otg_set_state) from [<80436f44>] (otg_statemachine+0x408/0x46c)
[<80436f44>] (otg_statemachine) from [<8043292c>] (ci_otg_fsm_work+0x3c/0x190)
[<8043292c>] (ci_otg_fsm_work) from [<8042ddfc>] (ci_otg_work+0x44/0x1c4)
[<8042ddfc>] (ci_otg_work) from [<80042b60>] (process_one_work+0xf4/0x35c)
[<80042b60>] (process_one_work) from [<80043814>] (worker_thread+0x130/0x3bc)
[<80043814>] (worker_thread) from [<80048f34>] (kthread+0xcc/0xe4)
[<80048f34>] (kthread) from [<8000e538>] (ret_from_fork+0x14/0x3c)
Code: e5953018 e3530000 0a000000 e12fff33 (e5878014)
LOG_2:
ci_hdrc ci_hdrc.0: EHCI Host Controller
ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 1
ci_hdrc ci_hdrc.1: doesn't support gadget
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = 80004000
[00000000] *pgd=00000000
In Online 00:00ternal e Offline rror: Oops: 80000005 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 108 Comm: kworker/u8:2 Not tainted 3.14.38-02007-g24b2734-dirty #127
Workque Online 00:00ue: ci_o Offline tg ci_otg_work
Online 00:00task: d8 Offline 39ec00 ti: d83ea000 task.ti: d83ea000
PC is at 0x0
LR is at usb_add_hcd+0x248/0x6e8
pc : [<00000000>] lr : [<8040f644>] psr: 60000113
sp : d83ebe60 ip : 00000000 fp : d8004400
r10: 00000001 r9 : 00000001 r8 : d85fd4b0
r7 : 00000000 r6 : 00000000 r5 : 00000000 r4 : d85fd400
r3 : 00000000 r2 : d85fd4f4 r1 : 80410178 r0 : d85fd400
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7d Table: 1000404a DAC: 00000015
Process kworker/u8:2 (pid: 108, stack limit = 0xd83ea238)
Stack: (0xd83ebe60 to 0xd83ec000)
be60: 00000000 80dd920c d8654e10 d85fd800 d803e010 d85fd400 00000000 00000000
be80: d8004400 00000000 d83ea008 80430e34 80430d14 d803e100 d803e010 d803e1ac
bea0: 00000000 80431dc8 80431d74 d803e100 00000001 80435858 80e130bc d803e100
bec0: 00000006 80435df8 00000000 d803e100 80e98ec8 804368e4 d803e010 d803e100
bee0: d86e8100 804322cc d86cf050 d803e1f4 d803e010 8042d79c 8042d758 d83cf900
bf00: d803e1f4 80042b78 00000000 00000003 00000001 00000001 800545e8 d83cf900
bf20: d8004400 d83cf918 d8004414 d83ea000 80e3f57b 00000089 d8004400 8004382c
bf40: d839ec00 00000000 d8393780 d83cf900 800436fc 00000000 00000000 00000000
bf60: 00000000 80048f50 80e019f4 00000000 0000264c d83cf900 00000000 00000000
bf80: d83ebf80 d83ebf80 00000000 00000000 d83ebf90 d83ebf90 d83ebfac d8393780
bfa0: 80048e84 00000000 00000000 8000e538 00000000 00000000 00000000 00000000
bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 ee66e85d 133ebd03
[<804 Online 00:000f644>] Offline (usb_add_hcd) from [<80430e34>] (host_start+0x120/0x2e4)
[<80430e34>] (host_start) from [<80431dc8>] (ci_otg_start_host+0x54/0xbc)
[<80431dc8>] (ci_otg_start_host) from [<80435858>] (otg_set_protocol+0xa4/0xd0)
[<80435858>] (otg_set_protocol) from [<80435df8>] (otg_set_state+0x574/0xc58)
[<80435df8>] (otg_set_state) from [<804368e4>] (otg_statemachine+0x408/0x46c)
[<804368e4>] (otg_statemachine) from [<804322cc>] (ci_otg_fsm_work+0x3c/0x190)
[<804322cc>] (ci_otg_fsm_work) from [<8042d79c>] (ci_otg_work+0x44/0x1c4)
[<8042d79c>] (ci_otg_work) from [<80042b78>] (process_one_work+0xf4/0x35c)
[<80042b78>] (process_one_work) from [<8004382c>] (worker_thread+0x130/0x3bc)
[<8004382c>] (worker_thread) from [<80048f50>] (kthread+0xcc/0xe4)
[<80048f50>] (kthread) from [<8000e538>] (ret_from_fork+0x14/0x3c)
Code: bad PC value
Cc: Jun Li <jun.li@freescale.com>
Cc: <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
This patch adds runtime power management support for otg fsm mode, since
A-device in a_idle state cannot detect data pulse irq after suspended, here
enable wakeup by connection before suspend to make it can be resumed by DP;
and handle wakeup from that state like SRP.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Define ci_get_revision API to know the controller revision
information according to chipidea 1.1a, 2.0a and 2.5a spec.
Besides, add one entry at struct ci_hdrc to indicate revision
information, it can be used for adding different code for
revisions, eg kinds of errata.
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need to do it for all otg capable controller, not only peripheral
featured otg capable controller, otherwise, the host-only role, but
otg capable controller may be responded by otg interrupt.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB signal can be system wakeup source, this patch add the
support, for how to enable it, see Documentation/usb/chipidea.txt.
Since USB wakeup enable logic is vendor/platform specific, the
glue layer needs to implement it to support this feature.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add runtime power management support.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 14b4099c074f2ddf4d84b22d370170e61b527529
It moved platform_set_drvdata(pdev, ci) before hcd is created,
and the hcd will assign itself as ci controller's drvdata during
the hcd creation function (in usb_create_shared_hcd), so it
overwrites the real ci's drvdata which we want to use.
So, if the controller is at host mode, the system suspend
API will get the wrong struct ci_hdrc pointer, and cause the
oops.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
|
|
Fixed typos in comments of 2 drivers/usb/chipidea files
Signed-off-by: Mickael Maison <mickael.maison@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The generic plaftorm device for ChipIdea drivers is probed by calling
ci_hdrc_probe. The device structure used is not the one of the specific
ChipIdea driver but the one of the generic ChipIdea platform device.
This results in not being able to probe the PHYs as we're not using the
right device structure. Since all ChipIdea drivers are retrieving their
PHYs in their specific driver code, this didn't impact any of them yet.
Fixes it using the right device structure (dev->parent).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The core driver has already done it, besides, move set driver data
operation just after ci has allocated successfully in case some
code (like ci_role_start) want to access this driver data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The hw_device_reset is dedicated to be used at device mode initializaiton,
so delete the parameter 'mode'. For host driver, the ehci driver will
handle all things.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add controller reset API, currently it is used for device mode only.
It may be used for host/otg driver in future.
Ususally, we need this API for dual-role switch and back from hibernation
suspend to let the controller at default state.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add system power management support
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The phy needs some delay to output the stable status from low
power mode. And for OTGSC, the status inputs are debounced
using a 1 ms time constant, so, delay 2ms for controller to get
the stable status(like vbus and id) when the phy leaves low power.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The individual PHY driver should take this responsibility if it
needs to delay between clear portsc.phcd and let the phy leave
low power mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
MM core code already complains when devm_kzalloc() fails, so no need to print
the error locally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Using devm_request_irq to instead of request_irq.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into driver-core-next
Remove all .owner fields from platform drivers
|
|
This patch adds support of the PHY framework for ChipIdea drivers.
Changes are done in both the ChipIdea common code and in the drivers
accessing the PHY. This is done by adding a new PHY member in
ChipIdea's structures and by taking care of it in the code.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch modify the generic code handling PHYs to allow them to be
supplied from the drivers. This adds checks to ensure no PHY was already
there when looking for one in the generic code. This also makes sure we
do not modify its state in the generic HCD functions, it was provided by
the driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The call of 'kfree(ci->hw_bank.regmap)' in ci_hdrc_remove() sometimes causes
a kernel oops when removing the ci_hdrc module.
Since there is no separate memory allocated for the ci->hw_bank.regmap array,
there is no need to free it.
Cc: v3.14+ <stable@@vger.kernel.org>
Signed-off-by: Torsten Fleischer <to-fleischer@t-online.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Some kernel-doc style comment are not satisfied for format, fix them.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We have only needed to enable otg initialization when both of
below conditions are satisfied:
- The controller is otg capable
- The gadget function is enabled
If the controller is otg capable, but is host-only configuration, we do
not need to access register otgsc and do any otg operations (eg, create
otg workqueue).
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For OTG and Embedded hosts, they may need TPL (Targeted Peripheral List)
for usb certification and other vender specific requirements, the
platform can tell chipidea core driver if it supports tpl through DT
or platform data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The otg queue work include operations: one is disable interrupt,
another one is call kernel queue work API. Many codes do this
operation, using one inline function to instead of them.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Update TODO list
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB OTG interrupt handling and fsm transitions according to USB OTG
and EH 2.0.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After the PHY has powered and initialized, it needs some delay
for controller to reflect PHY's status. Some status and values
for id, vbus, dp/dm are only stable after this delay. The current
code tries to clear id/vbus status without enough delay, it
causes the status are not cleared properly.
This patch add 2ms delay after phy has initialized, and clear the
unexpected status after that.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
