| Age | Commit message (Collapse) | Author |
|---|
|
git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
* 'for-usb-linus' of ra.kernel.org:/pub/scm/linux/kernel/git/sarah/xhci:
usb, xhci: Clear warm reset change event during init
xhci: Set slot and ep0 flags for address command.
usb, xhci: fix lockdep warning on endpoint timeout
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
|
|
Matt's AsMedia xHCI host controller was responding with a Context Error
to an address device command after a configured device reset. Some
sequence of events leads both the slot and endpoint zero add flags
cleared to zero, which the AsMedia host doesn't like:
[ 223.701839] xhci_hcd 0000:03:00.0: Slot ID 1 Input Context:
[ 223.701841] xhci_hcd 0000:03:00.0: @ffff880137b25000 (virt) @ffffc000 (dma) 0x000000 - drop flags
[ 223.701843] xhci_hcd 0000:03:00.0: @ffff880137b25004 (virt) @ffffc004 (dma) 0x000000 - add flags
[ 223.701846] xhci_hcd 0000:03:00.0: @ffff880137b25008 (virt) @ffffc008 (dma) 0x000000 - rsvd2[0]
[ 223.701848] xhci_hcd 0000:03:00.0: @ffff880137b2500c (virt) @ffffc00c (dma) 0x000000 - rsvd2[1]
[ 223.701850] xhci_hcd 0000:03:00.0: @ffff880137b25010 (virt) @ffffc010 (dma) 0x000000 - rsvd2[2]
[ 223.701852] xhci_hcd 0000:03:00.0: @ffff880137b25014 (virt) @ffffc014 (dma) 0x000000 - rsvd2[3]
[ 223.701854] xhci_hcd 0000:03:00.0: @ffff880137b25018 (virt) @ffffc018 (dma) 0x000000 - rsvd2[4]
[ 223.701857] xhci_hcd 0000:03:00.0: @ffff880137b2501c (virt) @ffffc01c (dma) 0x000000 - rsvd2[5]
[ 223.701858] xhci_hcd 0000:03:00.0: Slot Context:
[ 223.701860] xhci_hcd 0000:03:00.0: @ffff880137b25020 (virt) @ffffc020 (dma) 0x8400000 - dev_info
[ 223.701862] xhci_hcd 0000:03:00.0: @ffff880137b25024 (virt) @ffffc024 (dma) 0x010000 - dev_info2
[ 223.701864] xhci_hcd 0000:03:00.0: @ffff880137b25028 (virt) @ffffc028 (dma) 0x000000 - tt_info
[ 223.701866] xhci_hcd 0000:03:00.0: @ffff880137b2502c (virt) @ffffc02c (dma) 0x000000 - dev_state
[ 223.701869] xhci_hcd 0000:03:00.0: @ffff880137b25030 (virt) @ffffc030 (dma) 0x000000 - rsvd[0]
[ 223.701871] xhci_hcd 0000:03:00.0: @ffff880137b25034 (virt) @ffffc034 (dma) 0x000000 - rsvd[1]
[ 223.701873] xhci_hcd 0000:03:00.0: @ffff880137b25038 (virt) @ffffc038 (dma) 0x000000 - rsvd[2]
[ 223.701875] xhci_hcd 0000:03:00.0: @ffff880137b2503c (virt) @ffffc03c (dma) 0x000000 - rsvd[3]
[ 223.701877] xhci_hcd 0000:03:00.0: Endpoint 00 Context:
[ 223.701879] xhci_hcd 0000:03:00.0: @ffff880137b25040 (virt) @ffffc040 (dma) 0x000000 - ep_info
[ 223.701881] xhci_hcd 0000:03:00.0: @ffff880137b25044 (virt) @ffffc044 (dma) 0x2000026 - ep_info2
[ 223.701883] xhci_hcd 0000:03:00.0: @ffff880137b25048 (virt) @ffffc048 (dma) 0xffffe8e0 - deq
[ 223.701885] xhci_hcd 0000:03:00.0: @ffff880137b25050 (virt) @ffffc050 (dma) 0x000000 - tx_info
[ 223.701887] xhci_hcd 0000:03:00.0: @ffff880137b25054 (virt) @ffffc054 (dma) 0x000000 - rsvd[0]
[ 223.701889] xhci_hcd 0000:03:00.0: @ffff880137b25058 (virt) @ffffc058 (dma) 0x000000 - rsvd[1]
[ 223.701892] xhci_hcd 0000:03:00.0: @ffff880137b2505c (virt) @ffffc05c (dma) 0x000000 - rsvd[2]
...
[ 223.701927] xhci_hcd 0000:03:00.0: // Ding dong!
[ 223.701992] xhci_hcd 0000:03:00.0: Setup ERROR: address device command for slot 1.
The xHCI spec says that both flags must be set to one for the Address
Device command. When the device is first enumerated,
xhci_setup_addressable_virt_dev() does set those flags. However, when
the device is addressed after it has been reset in the configured state,
xhci_setup_addressable_virt_dev() is not called, and
xhci_copy_ep0_dequeue_into_input_ctx() is called instead. That function
relies on the flags being set up by previous commands, which apparently
isn't a good assumption.
Move the setting of the flags into the common parent function.
This should be queued for stable kernels as old as 2.6.35, since that
was the first introduction of xhci_copy_ep0_dequeue_into_input_ctx.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Matt <mdm@iinet.net.au>
Cc: stable@vger.kernel.org
|
|
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (37 commits)
MIPS: O32: Provide definition of registers ta0 .. ta3.
MIPS: perf: Add Octeon support for hardware perf.
MIPS: perf: Add support for 64-bit perf counters.
MIPS: perf: Reorganize contents of perf support files.
MIPS: perf: Cleanup formatting in arch/mips/kernel/perf_event.c
MIPS: Add accessor macros for 64-bit performance counter registers.
MIPS: Add probes for more Octeon II CPUs.
MIPS: Add more CPU identifiers for Octeon II CPUs.
MIPS: XLR, XLS: Add comment for smp setup
MIPS: JZ4740: GPIO: Check correct IRQ in demux handler
MIPS: JZ4740: GPIO: Simplify IRQ demuxer
MIPS: JZ4740: Use generic irq chip
MIPS: Alchemy: remove all CONFIG_SOC_AU1??? defines
MIPS: Alchemy: kill au1xxx.h header
MIPS: Alchemy: clean DMA code of CONFIG_SOC_AU1??? defines
MIPS, IDE: Alchem, au1xxx-ide: Remove pb1200/db1200 header dep
MIPS: Alchemy: Redo PCI as platform driver
MIPS: Alchemy: more base address cleanup
MIPS: Alchemy: rewrite USB platform setup.
MIPS: Alchemy: abstract USB block control register access
...
Fix up trivial conflicts in:
arch/mips/alchemy/devboards/db1x00/platform.c
drivers/ide/Kconfig
drivers/mmc/host/au1xmmc.c
drivers/video/Kconfig
sound/mips/Kconfig
|
|
While debugging a usb3 problem, I stumbled upon this lockdep warning.
Oct 18 21:41:17 dhcp47-74 kernel: =================================
Oct 18 21:41:17 dhcp47-74 kernel: [ INFO: inconsistent lock state ]
Oct 18 21:41:17 dhcp47-74 kernel: 3.1.0-rc4nmi+ #456
Oct 18 21:41:17 dhcp47-74 kernel: ---------------------------------
Oct 18 21:41:17 dhcp47-74 kernel: inconsistent {IN-HARDIRQ-W} -> {HARDIRQ-ON-W} usage.
Oct 18 21:41:17 dhcp47-74 kernel: swapper/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
Oct 18 21:41:17 dhcp47-74 kernel: (&(&xhci->lock)->rlock){?.-...}, at: [<ffffffffa0228990>] xhci_stop_endpoint_command_watchdog+0x30/0x340 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: {IN-HARDIRQ-W} state was registered at:
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8109a941>] __lock_acquire+0x781/0x1660
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8109bed7>] lock_acquire+0x97/0x170
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81501b46>] _raw_spin_lock+0x46/0x80
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa02299fa>] xhci_irq+0x3a/0x1960 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa022b351>] xhci_msi_irq+0x31/0x40 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810d2305>] handle_irq_event_percpu+0x85/0x320
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810d25e8>] handle_irq_event+0x48/0x70
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810d537d>] handle_edge_irq+0x6d/0x130
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810048c9>] handle_irq+0x49/0xa0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8150d56d>] do_IRQ+0x5d/0xe0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff815029b0>] ret_from_intr+0x0/0x13
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81388aca>] usb_set_device_state+0x8a/0x180
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8138f038>] usb_add_hcd+0x2b8/0x730
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa022ed7e>] xhci_pci_probe+0x9e/0xd4 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8127915f>] local_pci_probe+0x5f/0xd0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8127a569>] pci_device_probe+0x119/0x120
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81334473>] driver_probe_device+0xa3/0x2c0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8133473b>] __driver_attach+0xab/0xb0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8133373c>] bus_for_each_dev+0x6c/0xa0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff813341fe>] driver_attach+0x1e/0x20
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81333b88>] bus_add_driver+0x1f8/0x2b0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81334df6>] driver_register+0x76/0x140
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8127a7c6>] __pci_register_driver+0x66/0xe0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa013c04a>] snd_timer_find+0x4a/0x70 [snd_timer]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa013c00e>] snd_timer_find+0xe/0x70 [snd_timer]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810001d3>] do_one_initcall+0x43/0x180
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810a9ed2>] sys_init_module+0x92/0x1f0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8150ab6b>] system_call_fastpath+0x16/0x1b
Oct 18 21:41:17 dhcp47-74 kernel: irq event stamp: 631984
Oct 18 21:41:17 dhcp47-74 kernel: hardirqs last enabled at (631984): [<ffffffff81502720>] _raw_spin_unlock_irq+0x30/0x50
Oct 18 21:41:17 dhcp47-74 kernel: hardirqs last disabled at (631983): [<ffffffff81501c49>] _raw_spin_lock_irq+0x19/0x90
Oct 18 21:41:17 dhcp47-74 kernel: softirqs last enabled at (631980): [<ffffffff8105ff63>] _local_bh_enable+0x13/0x20
Oct 18 21:41:17 dhcp47-74 kernel: softirqs last disabled at (631981): [<ffffffff8150ce6c>] call_softirq+0x1c/0x30
Oct 18 21:41:17 dhcp47-74 kernel:
Oct 18 21:41:17 dhcp47-74 kernel: other info that might help us debug this:
Oct 18 21:41:17 dhcp47-74 kernel: Possible unsafe locking scenario:
Oct 18 21:41:17 dhcp47-74 kernel:
Oct 18 21:41:17 dhcp47-74 kernel: CPU0
Oct 18 21:41:17 dhcp47-74 kernel: ----
Oct 18 21:41:17 dhcp47-74 kernel: lock(&(&xhci->lock)->rlock);
Oct 18 21:41:17 dhcp47-74 kernel: <Interrupt>
Oct 18 21:41:17 dhcp47-74 kernel: lock(&(&xhci->lock)->rlock);
Oct 18 21:41:17 dhcp47-74 kernel:
Oct 18 21:41:17 dhcp47-74 kernel: *** DEADLOCK ***
Oct 18 21:41:17 dhcp47-74 kernel:
Oct 18 21:41:17 dhcp47-74 kernel: 1 lock held by swapper/0:
Oct 18 21:41:17 dhcp47-74 kernel: #0: (&ep->stop_cmd_timer){+.-...}, at: [<ffffffff8106abf2>] run_timer_softirq+0x162/0x570
Oct 18 21:41:17 dhcp47-74 kernel:
Oct 18 21:41:17 dhcp47-74 kernel: stack backtrace:
Oct 18 21:41:17 dhcp47-74 kernel: Pid: 0, comm: swapper Tainted: G W 3.1.0-rc4nmi+ #456
Oct 18 21:41:17 dhcp47-74 kernel: Call Trace:
Oct 18 21:41:17 dhcp47-74 kernel: <IRQ> [<ffffffff81098ed7>] print_usage_bug+0x227/0x270
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810999c6>] mark_lock+0x346/0x410
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8109a7de>] __lock_acquire+0x61e/0x1660
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81099893>] ? mark_lock+0x213/0x410
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8109bed7>] lock_acquire+0x97/0x170
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa0228990>] ? xhci_stop_endpoint_command_watchdog+0x30/0x340 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81501b46>] _raw_spin_lock+0x46/0x80
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa0228990>] ? xhci_stop_endpoint_command_watchdog+0x30/0x340 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa0228990>] xhci_stop_endpoint_command_watchdog+0x30/0x340 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8106abf2>] ? run_timer_softirq+0x162/0x570
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8106ac9d>] run_timer_softirq+0x20d/0x570
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8106abf2>] ? run_timer_softirq+0x162/0x570
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffffa0228960>] ? xhci_queue_isoc_tx_prepare+0x8e0/0x8e0 [xhci_hcd]
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff810604d2>] __do_softirq+0xf2/0x3f0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81020edd>] ? lapic_next_event+0x1d/0x30
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81090d4e>] ? clockevents_program_event+0x5e/0x90
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8150ce6c>] call_softirq+0x1c/0x30
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8100484d>] do_softirq+0x8d/0xc0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8105ff35>] irq_exit+0xe5/0x100
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8150d65e>] smp_apic_timer_interrupt+0x6e/0x99
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff8150b6f0>] apic_timer_interrupt+0x70/0x80
Oct 18 21:41:17 dhcp47-74 kernel: <EOI> [<ffffffff81095d8d>] ? trace_hardirqs_off+0xd/0x10
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff812ddb76>] ? acpi_idle_enter_bm+0x227/0x25b
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff812ddb71>] ? acpi_idle_enter_bm+0x222/0x25b
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff813eda63>] cpuidle_idle_call+0x103/0x290
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81002155>] cpu_idle+0xe5/0x160
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff814e7f50>] rest_init+0xe0/0xf0
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff814e7e70>] ? csum_partial_copy_generic+0x170/0x170
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81df8e23>] start_kernel+0x3fc/0x407
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81df8321>] x86_64_start_reservations+0x131/0x135
Oct 18 21:41:17 dhcp47-74 kernel: [<ffffffff81df8412>] x86_64_start_kernel+0xed/0xf4
Oct 18 21:41:17 dhcp47-74 kernel: xhci_hcd 0000:00:14.0: xHCI host not responding to stop endpoint command.
Oct 18 21:41:17 dhcp47-74 kernel: xhci_hcd 0000:00:14.0: Assuming host is dying, halting host.
Oct 18 21:41:17 dhcp47-74 kernel: xhci_hcd 0000:00:14.0: HC died; cleaning up
Oct 18 21:41:17 dhcp47-74 kernel: usb 3-4: device descriptor read/8, error -110
Oct 18 21:41:17 dhcp47-74 kernel: usb 3-4: device descriptor read/8, error -22
Oct 18 21:41:17 dhcp47-74 kernel: hub 3-0:1.0: cannot disable port 4 (err = -19)
Basically what is happening is in xhci_stop_endpoint_command_watchdog()
the xhci->lock is grabbed with just spin_lock. What lockdep deduces is
that if an interrupt occurred while in this function it would deadlock
with xhci_irq because that function also grabs the xhci->lock.
Fixing it is trivial by using spin_lock_irqsave instead.
This should be queued to stable kernels as far back as 2.6.33.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
|
|
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
ARM: tegra: update defconfig
arm/tegra: Harmony: Configure PMC for low-level interrupts
arm/tegra: device tree support for ventana board
arm/tegra: add support for ventana pinmuxing
arm/tegra: prepare Seaboard pinmux code for derived boards
arm/tegra: pinmux: ioremap registers
gpio/tegra: Convert to a platform device
arm/tegra: Convert pinmux driver to a platform device
arm/dt: Tegra: Add pinmux node to tegra20.dtsi
arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
ARM: mx5: fix clock usage for suspend
ARM i.MX entry-macro.S: remove now unused code
ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
ARM i.MX tzic: add handle_irq function
ARM i.MX avic: add handle_irq function
ARM: mx25: Add the missing IIM base definition
ARM i.MX avic: convert to use generic irq chip
mx31moboard: Add poweroff support
ARM: mach-qong: Add watchdog support
ARM: davinci: AM18x: Add wl1271/wlan support
...
Fix up conflicts in:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-mx5/devices-imx53.h
arch/arm/plat-mxc/include/mach/memory.h
|
|
To fix this build error on ARM:
drivers/usb/host/xhci-hub.c: In function 'xhci_stop_device':
drivers/usb/host/xhci-hub.c:261: error: 'GFP_NOIO' undeclared (first use in this function)
make[4]: *** [drivers/usb/host/xhci-hub.o] Error 1
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
With module.h being implicitly everywhere via device.h, the absence
of explicitly including something for EXPORT_SYMBOL went unnoticed.
Since we are heading to fix things up and clean module.h from the
device.h file, we need to explicitly include these files now.
Use the lightweight version of the header that has just THIS_MODULE
and EXPORT_SYMBOL variants.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
The situation up to this point meant that module.h was pretty
much everywhere, regardless of whether you asked for it or not.
We are fixing that, so give the USB folks who want it an actual
include of it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Conflicts:
arch/arm/mach-mxs/include/mach/gpio.h
arch/arm/plat-mxc/include/mach/gpio.h
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'gpio' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm: (43 commits)
ARM: 7135/1: ep93xx: bring back missing <mach/gpio.h>
ARM: 7104/1: plat-pxa: break out GPIO driver specifics
ARM: 7103/1: plat-pxa: move PXA GPIO driver to GPIO subsystem
ARM: 7042/3: mach-ep93xx: break out GPIO driver specifics
ARM: 7101/1: arm/tegra: Replace <mach/gpio.h> with <mach/gpio-tegra.h>
ARM: 7094/1: arm/tegra: Move EN_VDD_1V05_GPIO to board-harmony.h
ARM: 7083/1: rewrite U300 GPIO to use gpiolib
ARM: 7074/1: gpio: davinci: eliminate unused variable warnings
ARM: 7063/1: Orion: gpio: add missing include of linux/types.h
ARM: 7055/1: arm/tegra: mach/gpio.h: include linux/types.h to fix build
ARM: 7054/1: arm/tegra: Delete custom gpio_to_irq, and irq_to_gpio
ARM: 7053/1: gpio/tegra: Implement gpio_chip.to_irq
ARM: 7052/1: gpio/tegra: Remove use of irq_to_gpio
ARM: 7057/1: mach-pnx4008: rename GPIO header
ARM: 7056/1: plat-nomadik: kill off <plat/gpio.h>
ARM: 7050/1: mach-sa1100: delete irq_to_gpio() function
ARM: 7049/1: mach-sa1100: move SA1100 GPIO driver to GPIO subsystem
ARM: 7045/1: mach-lpc32xx: break out GPIO driver specifics
ARM: 7044/1: mach-lpc32xx: move LPC32XX GPIO driver to GPIO subsystem
ARM: 7043/1: mach-ixp2000: rename GPIO header
...
Fix up trivial conflicts in arch/arm/mach-u300/Kconfig manually
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (260 commits)
usb: renesas_usbhs: fixup inconsistent return from usbhs_pkt_push()
usb/isp1760: Allow to optionally trigger low-level chip reset via GPIOLIB.
USB: gadget: midi: memory leak in f_midi_bind_config()
USB: gadget: midi: fix range check in f_midi_out_open()
QE/FHCI: fixed the CONTROL bug
usb: renesas_usbhs: tidyup for smatch warnings
USB: Fix USB Kconfig dependency problem on 85xx/QoirQ platforms
EHCI: workaround for MosChip controller bug
usb: gadget: file_storage: fix race on unloading
USB: ftdi_sio.c: Use ftdi async_icount structure for TIOCMIWAIT, as in other drivers
USB: ftdi_sio.c:Fill MSR fields of the ftdi async_icount structure
USB: ftdi_sio.c: Fill LSR fields of the ftdi async_icount structure
USB: ftdi_sio.c:Fill TX field of the ftdi async_icount structure
USB: ftdi_sio.c: Fill the RX field of the ftdi async_icount structure
USB: ftdi_sio.c: Basic icount infrastructure for ftdi_sio
usb/isp1760: Let OF bindings depend on general CONFIG_OF instead of PPC_OF .
USB: ftdi_sio: Support TI/Luminary Micro Stellaris BD-ICDI Board
USB: Fix runtime wakeup on OHCI
xHCI/USB: Make xHCI driver have a BOS descriptor.
usb: gadget: add new usb gadget for ACM and mass storage
...
|
|
Now that no driver any longer depends on the CONFIG_SOC_AU1??? symbols,
it's time to get rid of them: Move some of the platform devices to the
boards which can use them, Rename a few (unused) constants in the header,
Replace them with MIPS_ALCHEMY in the various Kconfig files. Finally
delete them altogether from the Alchemy Kconfig file.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Alchemy chips have one or more registers which control access
to the usb blocks as well as PHY configuration. I don't want
the OHCI/EHCI glues to know about the different registers and bits;
new code hides the gory details of USB configuration from them.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: linux-usb@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Patchwork: https://patchwork.linux-mips.org/patch/2709/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 drivers/usb/host/alchemy-common.c
|
|
|
|
Properly triggering the reset wire is necessary with the ISP1761 used
on Terasic DE4 Altera-FPGA boards using a NIOS2 processor, for example.
This is an optional implementation for the OF binding only. The other
bindings just pass an invalid GPIO to the isp1760_register() routine.
Example, usage in DTS:
gpios = <&pio_isp1761rst_0 0 1>;
to point to a GPIO controller from within the ISP1761 node: GPIO 0, active low.
Signed-off-by: Joachim Foerster <joachim.foerster@missinglinkelectronics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
For USB CONTROL transaction, when the data length is zero,
the IN package is needed to finish this transaction in status stage.
Signed-off-by: Jerry Huang <r66093@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1489) works around a hardware bug in MosChip EHCI
controllers. Evidently when one of these controllers increments the
frame-index register, it changes the three low-order bits (the
microframe counter) before changing the higher order bits (the frame
counter). If the register is read at just the wrong time, the value
obtained is too low by 8.
When the appropriate quirk flag is set, we work around this problem by
reading the frame-index register a second time if the first value's
three low-order bits are all 0. This gives the hardware a chance to
finish updating the register, yielding the correct value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jason N Pitt <jpitt@fhcrc.org>
CC: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
To be able to use the driver on other OF-aware architectures, too.
And add necessary OF related #includes to fix compilation error.
Signed-off-by: Joachim Foerster <joachim.foerster@missinglinkelectronics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
At least some OHCI hardware (such as the MCP89) fails to flag any change
in the host status register or the port status registers when receiving
a remote wakeup while in D3 state. This results in the controller being
resumed but no device state change being noticed, at which point the
controller is put back to sleep again. Since there doesn't seem to be any
reliable way to identify the state change, just unconditionally resume the
hub. It'll be put back to sleep in the near future anyway if there are no
active devices attached to it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: stable <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
To add USB 3.0 link power management (LPM), we need to know what the U1
and U2 exit latencies are for the xHCI host controller. External USB 3.0
hubs report these values through the SuperSpeed Capabilities descriptor in
the BOS descriptor. Make the USB 3.0 roothub for the xHCI host behave
like an external hub and return the BOS descriptors.
The U1 and U2 exit latencies will vary across each host controller, so we
need to dynamically fill those values in by reading the exit latencies out
of the xHC registers. Make the roothub code in the USB core handle
hub_control() returning the length of the data copied.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This is mod_host prototype support for renesas_usbhs driver.
It doesn't support USB-Hub, and USB-DMAC for now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch (as1488) improves the comments and logic in uhci-hcd's
suspend routine. The existing comments are hard to understand and
don't give a good idea of what's really going on.
The question of whether EGSM (Enter Global Suspend Mode) and RD
(enable Resume Detect interrupts) can be useful when they're not both
set is difficult. The spec doesn't give any details on how they
interact with system wakeup, although clearly they are meant to be
used together. To be safe, the patch changes the subroutine so that
neither bit gets set unless they both do. There shouldn't be any
functional changes from this; only systems that are designed badly or
broken in some way need to avoid using those bits.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This removes the need of ifdefs within the init function and with it the
headache about the correct clean without bus X but with bus/platform Y &
Z.
xhci-pci is only compiled if CONFIG_PCI is selected which can be
de-selected now without trouble. For now the result is kinda useless
because we have no other glue code. However, since nobody is using
USB_ARCH_HAS_XHCI then it should not be an issue :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
xhci_gen_setup() is generic so it can be used to perform the bare xhci
setup even on non-pci based platform. The typedef for the function
pointer is moved into the headerfile
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
xhci_pci_setup() is split into three pieces:
- xhci_gen_setup()
The major remaining of xhci_pci_setup() is now containing the generic
part of the xhci setup. It allocates the xhci struct, setup
hcs_params? and friends, performs xhci_halt(), xhci_init and so one.
It also obtains the quirks via a callback
- xhci_pci_quirks()
It checks the origin of the xhci core and sets core specific quirks.
- xhci_pci_setup()
PCI specific setup functions. Besides calling xhci_gen_setup() with
xhci_pci_quirks() as an argument it performs PCI specific setup like
obtaining the address of sbrn via a PCI config space.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
pci_*_consistent() calls dma_*_coherent() with GFP_ATOMIC and requires
pci_dev struct. This is a preparion for later where we no longer have
the pci struct around.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The MSI related fuctionality requires a few structs which are not
available if CONFIG_PCI is not enabled. This is a prepartion to allow
xhci be built without CONFIG_PCI set.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch moves the complete MSI/MSI-X/Legacy dance into its own
function. There is however one difference: If the XHCI_BROKEN_MSI flag
is set then we don't free and register the irq, we simply return.
This is preparation for later PCI decouple.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
to make it look like OHCI and EHCI, we introduce
that symbol and USB_XHCI_HCD depend on that
instead of PCI.
[bigeasy@linutronix.de: wire up USB_ARCH_HAS_HCD]
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix the debug message in xhci_address_device().
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Setting the chain (CH) bit in the link TRB of isochronous transfer rings
is required by AMD 0.96 xHCI host controller to successfully transverse
multi-TRB TD that span through different memory segments.
When a Missed Service Error event occurs, if the chain bit is not set in
the link TRB and the host skips TDs which just across a link TRB, the
host may falsely recognize the link TRB as a normal TRB. You can see
this may cause big trouble - the host does not jump to the right address
which is pointed by the link TRB, but continue fetching the memory which
is after the link TRB address, which may not even belong to the host,
and the result cannot be predicted.
This causes some big problems. Without the former patch I sent: "xHCI:
prevent infinite loop when processing MSE event", the system may hang.
With that patch applied, system does not hang, but the host still access
wrong memory address and isoc transfer will fail. With this patch,
isochronous transfer works as expected.
This patch should be applied to kernels as old as 2.6.36, which was when
the first isochronous support was added for the xHCI host controller.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
If the device pass the USB2 software LPM and the host supports hardware
LPM, enable hardware LPM for the device to let the host decide when to
put the link into lower power state.
If hardware LPM is enabled for a port and driver wants to put it into
suspend, it must first disable hardware LPM, resume the port into U0,
and then suspend the port.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch tests USB2 software LPM for a USB2 LPM-capable device.
When a lpm-capable device is addressed, if the host also supports software
LPM, apply a test by putting the device into L1 state and resume it to see
if the device can do L1 suspend/resume successfully.
If the device fails to enter L1 or resume from L1 state, it may not
function normally and usbcore may disconnect and re-enumerate it. In this
case, store the device's Vid and Pid information, make sure the host will
not test LPM for it twice.
The test result is per device/host. Some devices claim to be lpm-capable,
but fail to enter L1 or resume. So the test is necessary.
The xHCI 1.0 errata has modified the USB2.0 LPM implementation. It redefines
the HIRD field to BESL, and adds another register Port Hardware LPM Control
(PORTHLPMC). However, this should not affect the LPM behavior on xHC which
does not implement 1.0 errata.
USB2.0 LPM errata defines a new bit BESL in the device's USB 2.0 extension
descriptor. If the device reports it uses BESL, driver should use BESL
instead of HIRD for it.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Check the host's USB2 LPM capability.
USB2 software LPM support is optional for xHCI 0.96 hosts. xHCI 1.0 hosts
should support software LPM, and may support hardware LPM.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
When the link state changes, xHC will report a port status change event
and set the PORT_PLC bit, for both USB3 and USB2 root hub ports.
The PLC will be cleared by usbcore for USB3 root hub ports, but not for
USB2 ports, because they do not report USB_PORT_STAT_C_LINK_STATE in
wPortChange.
Clear it for USB2 root hub ports in handle_port_status().
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Introduce xhci_test_and_clear_bit() to clear RWC bit in PORTSC register.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Introduce xhci_set_link_state() to remove redundant codes.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This allow to clean duplicated code in most of SOC driver.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org> # fixes 3.1 build error
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The seg argument to xhci_segment_free is never passed as NULL, so
no need to check for this in xhci_segment_free.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
There are 2 situations wherein the xhci_ring* might not get freed:
- When xhci_ring_alloc() -> xhci_segment_alloc() returns NULL and
we goto the fail: label in xhci_ring_alloc. In this case, the ring
will not get kfreed.
- When the num_segs argument to xhci_ring_alloc is passed as 0 and
we try to free the rung after that.
( This doesn't really happen as of now in the code but we seem to
be entertaining num_segs=0 in xhci_ring_alloc )
This should be backported to kernels as old as 2.6.31.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The Intel Panther Point xHCI host tracks SuperSpeed endpoints in a
different way than USB 2.0/1.1 endpoints. The bandwidth interval tables
are not used, and instead the bandwidth is calculated in a very simple
way. Bandwidth for SuperSpeed endpoints is tracked individually in each
direction, since each direction has the full USB 3.0 bandwidth available.
10% of the bus bandwidth is reserved for non-periodic transfers.
This checking would be more complex if we had USB 3.0 LPM enabled, because
an additional latency for isochronous ping times need to be taken into
account. However, we don't have USB 3.0 LPM support in Linux yet.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The "Mult" bits in the SuperSpeed Endpoint Companion Descriptor are
zero-based, and the xHCI host controller wants them to be zero-based in
the input context. However, for the bandwidth math, we want them to be
one-based. Fix this.
Fix the documentation about the endpoint bandwidth mult variable in the
xhci.h file, which says it is zero-based. Also fix the documentation
about num_packets, which is also one-based, not zero-based.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
instead of reading the xhci interface version each time _even_ if the
quirk is not required, simply check if the quirk flag is set. This flag
is only set of the module parameter is set and here is where I moved the
version check to.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
When a xHC host is unable to handle isochronous transfer in the
interval, it reports a Missed Service Error event and skips some tds.
Currently xhci driver handles MSE event in the following ways:
1. When encounter a MSE event, set ep->skip flag, update event ring
dequeue pointer and return.
2. When encounter the next event on this ep, the driver will run the
do-while loop, fetch td from ep's td_list to find the td
corresponding to this event. All tds missed are marked as short
transfer(-EXDEV).
The do-while loop will end in two ways:
1. If the td pointed by the event trb is found;
2. If the ep ring's td_list is empty.
However, if a buggy HW reports some unpredicted event (for example, an
overrun event following a MSE event while the ep ring is actually not
empty), the driver will never find the td, and it will loop until the
td_list is empty.
Unfortunately, the spinlock is dropped when give back a urb in the
do-while loop. During the spinlock released period, the class driver
may still submit urbs and add tds to the td_list. This may cause
disaster, since the td_list will never be empty and the loop never ends,
and the system hangs.
To fix this, count the number of TDs on the ep ring before skipping TDs,
and quit the loop when skipped that number of tds. This guarantees the
do-while loop will end after certain number of cycles, and driver will
not be trapped in an infinite loop.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Sometimes, when a USB 3.0 device is disconnected, the Intel Panther
Point xHCI host controller will report a link state change with the
state set to "SS.Inactive". This causes the xHCI host controller to
issue a warm port reset, which doesn't finish before the USB core times
out while waiting for it to complete.
When the warm port reset does complete, and the xHC gives back a port
status change event, the xHCI driver kicks khubd. However, it fails to
set the bit indicating there is a change event for that port because the
logic in xhci-hub.c doesn't check for the warm port reset bit.
After that, the warm port status change bit is never cleared by the USB
core, and the xHC stops reporting port status change bits. (The xHCI
spec says it shouldn't report more port events until all change bits are
cleared.) This means any port changes when a new device is connected
will never be reported, and the port will seem "dead" until the xHCI
driver is unloaded and reloaded, or the computer is rebooted. Fix this
by making the xHCI driver set the port change bit when a warm port reset
change bit is set.
A better solution would be to make the USB core handle warm port reset
in differently, merging the current code with the standard port reset
code that does an incremental backoff on the timeout, and tries to
complete the port reset two more times before giving up. That more
complicated fix will be merged next window, and this fix will be
backported to stable.
This should be backported to kernels as old as 3.0, since that was the
first kernel with commit a11496ebf375 ("xHCI: warm reset support").
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This flag is a NOOP and can be removed now.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
According to ehci spec 4.10.2, Advance Queue
If the fetched qTD has its Active bit set to a zero, the
host controller aborts the queue advance and follows the
queue head's horizontal pointer to the next schedule data
structure.
the 'qtd' will be linked into qh hardware queue after the line
below
*dummy = *qtd;
is executed and observed by EHCI HC, but EHCI HC won't have chance to
fetch the qtd descriptor pointed by 'qtd' in qh_append_tds until the
line below
dummy->hw_token = token; #set Active bit here
is executed by CPU and observed by EHCI HC.
There is already one 'wmb' to order writing to 'dummy'/'qtd' descriptors
and writing 'token' to 'dummy' descriptor(set Active bit), so the 1st
wmb is not needed and can be removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
EHCI_SHRINK_JIFFIES should be 5ms, which was just used originally,
and not 200ms, so fix it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Obviously, ZLP is only required for transfer of OUT direction,
so just take same policy with UHCI for ZLP packet.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
