| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
LCD blink is observed during suspend/resume and blank/unblank
operations as backlight is ON during LCDC disable and enable.
So make sure to turn OFF backlight before disabling and turn
it ON after enabling.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
As in specification software reset should be applied for several
cycles before bringing it out of reset. Without this patch
particularly during suspend and resume clock reset is not guaranteed
to happen.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Patch works around the below silicon errata:
During LCDC initialization, there is the potential for a FIFO
underflow condition to occur. A FIFO underflow condition
occurs when the input FIFO is completely empty and the LCDC
raster controller logic that drives data to the output pins
attempts to fetch data from the FIFO. When a FIFO underflow
condition occurs, incorrect data will be driven out on the
LCDC data pins.
Software should poll the FUF bit field in the LCD_STAT register
to check if an error condition has occurred or service the
interrupt if FUF_EN is enabled when FUF occurs. If the FUF bit
field has been set to 1, this will indicate an underflow
condition has occurred and then the software should execute a
reset of the LCDC via the LPSC.
This problem may occur if the LCDC FIFO threshold size
(LCDDMA_CTRL[TH_FIFO_READY]) is left at its default value after
reset. Increasing the FIFO threshold size will reduce or
eliminate underflows. Setting the threshold size to 256 double
words or larger is recommended.
Above issue is described in section 2.1.3 of silicon errata
http://www.ti.com/lit/er/sprz313e/sprz313e.pdf
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Flicker/tearing effect is observed with current FB driver.
Issue is because of 2 active DMA channels ping ponging among them
along with usage of 2 DDR ping pong buffers in driver. Application
unaware of active DMA channel keeps updating frame being displayed,
this leads to tearing effect.
Below steps describes the issue:
1)Initially assume both buffers FB0 and FB1 are programmed for buffer-0.
2)On EOF0: Program FB0 for buffer-1, indicate(wake up) application
to fill up buffer-0. As FB1 is active and continues to DMA buffer-0
(which is being filled), leading to tearing/flickering issue.
3)On EOF1: Program FB1 for buffer-0, indicate(wake up) application to
fill up buffer-1. As FB0 is active and continues to DMA buffer-1(which
is being filled), leading to tearing/flickering issue.
4)On EOF0: Program FB0 for buffer-1, indicate(wake up) application to
fill up buffer-0. As FB1 is active and continues to DMA buffer-0(which is
being filled), leading to tearing/flickering issue.
...
Above steps depict that issue is because of 1 frame delay in frame
panned by application.
Patch fixes the issue by keeping track free DMA channel and configures
it in drivers PAN callback so that panned frame from application gets
displayed in next frame period.
Wiki below describes the issue in detail and it also has link to
application with which issue can be reproduced.
http://processors.wiki.ti.com/index.php/DA8xx_LCDC_Linux_FB_FAQs
Signed-off-by: Nellutla, Aditya <aditya.n@ti.com>
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Writing '1' to particular bit of IRQENABLE_CLEAR register disables the
corresponding interrupt on revision 2 LCDC. This register was wrongly
configured to disable all previous enabled interrupts instead of
disabling only palette completion interrupt. Patch fixes it by clearing
only palette completion interrupt bit.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
add FB_BLANK_NORMAL, FB_BLANK_VSYNC_SUSPEND and FB_BLANK_HSYNC_SUSPEND
modes (copy drivers/video/omap2/omapfb/omapfb-main.c implementation).
Otherwise X-server will complain about invalid parameter.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
In the real time use-case when SGX is used for rendering to FB buffers it has been
observed that, the available memory from framebuffer driver is not sufficient for
SGX under certain cases (like 16-bit WVGA resolution). SGX requires 2 swap buffers
with each of the buffers aligned to lcm(line_length, PAGE_SIZE).
Inorder to satisfy this requirement, we have two options,
- Increase number of FB buffers (LCD_NUM_BUFFERS) to 3. This is not
recommended as we end up wasting huge memory in most of the cases.
- Align FB buffers to lcm(line_length, PAGE_SIZE).This ensures framebuffer
size is increased to satisfy SGX requirements keeping alignment intact.
This patch makes sure that FB allocates buffers aligned to above formula.
Signed-off-by: Aditya Nellutla <aditya.n@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Add timing data for Hitachi SP10Q010 display and allow configuration
of the 4bpp palette. For 4bpp framebuffer enable reversed order of
pixels in a byte. This requires defining FB_CFB_REV_PIXELS_IN_BYTE
and additionally setting var.nonstd to the value FB_NONSTD_REV_PIX_IN_B.
Note that it is not enough to set da8xx_fb_var.nonstd to this value
statically, since FBIOPUT_VSCREENINFO ioctl might pass var struct with
.nonstd field set to zero or another value. Therefore this setting must
be adjusted in fb_check_var() according to the requested bpp value.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Timing info is not properly reported by the driver, e.g.:
$ fbset -i
mode "480x272-35"
# D: 7.895 MHz, H: 12.165 kHz, V: 35.158 Hz
geometry 480 272 480 544 16
timings 126666 64 64 32 32 41 10
According to the timing values defined for LK043T1DG01 display
it should be reported as:
mode "480x272-53"
# D: 7.895 MHz, H: 15.038 kHz, V: 52.579 Hz
geometry 480 272 480 544 16
timings 126666 2 2 2 2 41 10
Initialize additional fb_var_screeninfo fields so fix this problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Patch calculates pixel clock period in pico seconds and updates
the same in variable screen information structure. fbset utility
uses this information.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Patch fixes build warning on label "err_cpu_freq" when CONFIG_CPU_FREQ
is not defined.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
LCDC functional clock may or may not be derived from CPU/MPU DPLL,
For example,
AM335x => Separate independent DPLL for LCDC
Davinci => Same DPLL as MPU
So, on platforms where LCDC functional clock is not derived from CPU/MPU
PLL it is not required to reset LCDC module as its functional clock does
not change with DVFS.
This patch adds check to do reset only if functional clock changes
between pre and post notifier callbacks with DVFS.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Patch follows the disable and software reset sequence specified
in version2 to LCDC functional specification.
Without this flicker is observed on re-enabling the LCDC.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
Revised LCD controller in upcoming TI SoC which is an updated version of
LCDC IP that was found on TI's DA850 SoC supports 2048*2048 resolution.
Below are the encoding details:
Width:
Pixels Per Line = {pplmsb, ppllsb, 4'b1111} + 1
Where pplmsb:1bit==>Raster Timing0[3], ppllsb:6bits==>Raster Timing0[9:4].
And encoded value can range from 16 to 2048 in multiples of 16.
Height:
Lines Per Panel = {lpp_b10, lpp}
Where lpp:10bits==>Raster Timing1[9:0], lpp_b10:1bit==>Raster Timing2[26].
And encoded value can range from 1 to 2048, programmable range is 0 to
2047.
Patch is verified on emulation platform of upcoming SoC for updated
feature and on DA850 platform to make sure nothing existing breaks.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
|
|
An upcoming SoC of TI comes with an LCD controller which is an updated
version of that found on TI's DA850 SoC. The da8xx-fb driver can support
this LCD with some enhancements.
This patch adds support for updated interrupt configuration on the new
SoC.
1) Registers for setting and clearing interrupts are different.
2) Raw and masked status registers are different.
The updates have been tested on an emulation platform for new features
and the patch has been tested on DA850 platform to make sure nothing
existing breaks.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
We must not use any information in the passed var besides xoffset,
yoffset and vmode as otherwise applications might abuse it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Martin Ambrose <martin@ti.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
The -rt patches change the console_semaphore to console_mutex. As a
result, a quite large chunk of the patches changes all
acquire/release_console_sem() to acquire/release_console_mutex()
This commit makes things use more neutral function names which dont make
implications about the underlying lock.
The only real change is the return value of console_trylock which is
inverted from try_acquire_console_sem()
This patch also paves the way to switching console_sem from a semaphore to
a mutex.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make console_trylock return 1 on success, per Geert]
Signed-off-by: Torben Hohn <torbenh@gmx.de>
Cc: Thomas Gleixner <tglx@tglx.de>
Cc: Greg KH <gregkh@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Current implementation puts CONFIG_CPU_FREQ at wrong place, CONFIG_CPU_FREQ
is for lcd_da8xx_cpufreq_deregister not for unregister_framebuffer.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Following commit exposed a bug in driver:
"fbdev: da8xx/omap-l1xx: implement double buffering"
Bug is, if interrupt handler is called before initialization is
finished, raster controller is enabled and following register
modifications causes hardware to stay in a broken state.
By looking at this one may say that proper locking is missing in
this driver, and a more proper fix should be prepared. However,
aformentioned commit causes a regression in the driver and some
fix to current one should be applied first.
Signed-off-by: Caglar Akyuz <caglar@bilkon-kontrol.com.tr>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This work includes the following:
- Implement handler for FBIO_WAITFORVSYNC ioctl.
- Allocate the data and palette buffers separately. A consequence of
this is that the palette and data loading is now done in different
phases. And that the LCD must be disabled temporarily after the palette
is loaded but this will only happen once after init and each time the
palette is changed. I think this is OK.
- Allocate two (ping and pong) framebuffers from memory.
- Add pan_display handler which toggles the LCDC DMA registers between
the ping and pong buffers.
Signed-off-by: Martin Ambrose <martin@ti.com>
Cc: Chaithrika U S <chaithrika@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
Implement frame buffer blank operation feature for DA8xx/OMAP-L1xx driver.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Suspend/resume support DA8xx/OMAP-L1xx frame buffer driver. This feature
has been tested on DA850/OMAP-L138 EVM. For the purpose of testing, the
patch series[1] which adds suspend support for DA850/OMAP-L138 SoC was
applied.
[1] http://patchwork.kernel.org/patch/60260/
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
management features
Add a helper function to enable raster. Also add one member in the
private data structure to track the current blank status, another function
pointer which takes in the platform specific callback function to control
panel power.
These updates will help in adding suspend/resume and frame buffer blank
operation features.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add cpufreq support for DA8xx/OMAP-L1xx frame buffer driver
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The clock divider value can be calculated from the pixel clock value for
the panel. This gives more flexiblity to the driver to change the divider
value on the fly as in the case of cpufreq feature- support for which will
be added shortly.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Steve Chen <schen@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Following issues have been addressed on DA8XX/OMAP-L1XX:
a. Screen misalignment during booting when frame buffer console is
enabled.
b. Driver was configured always in PSEUDOCOLOR mode. This patch
dynamically configures the driver either in PSEUDOCOLOUR or TRUECOLOR
mode depending on bpp.
c. The RED and BLUE offsets were interchanged resulting in wrong
bootup logo colour.
This patch has been tested on DA830/OMAP-L137 and DA850/OMAP-L138 EVMs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Steve Chen <schen@mvista.com>
Cc: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The return should be negative on errors
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
fix the following 'make includecheck' warning:
drivers/video/da8xx-fb.c: linux/device.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since the previous version, return values in ioctl() function have been
modified.
[akpm@linux-foundation.org: simplify lcd_disable_raster()]
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Steve Chen <schen@mvista.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add LCD controller (LCDC) driver for TI's DA8xx/OMAP-L1xx architecture.
LCDC specifications can be found at http://www.ti.com/litv/pdf/sprufm0a.
LCDC on DA8xx consists of two independent controllers, the Raster
Controller and the LCD Interface Display Driver (LIDD) controller. LIDD
further supports character and graphic displays.
This patch adds support for the graphic display (Sharp LQ035Q3DG01) found
on the DA830 based EVM. The EVM details can be found at:
http://support.spectrumdigital.com/boards/dskda830/revc/.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Steve Chen <schen@mvista.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
DESC
davinci-fb-frame-buffer-driver-for-ti-da8xx-omap-l1xx-fix
EDESC
From: Andrew Morton <akpm@linux-foundation.org>
fix kconfig indenting
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Cc: Steve Chen <schen@mvista.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
