| Age | Commit message (Collapse) | Author |
|---|
|
The color conversion coefficients for RGB to YUV conversion (used with
writeback) don't result in the correct result. This patch sets the
correct coefficients.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
When doing mem-to-mem writeback, there's no pixelclock. However, the
code that calculates scaling factors check that there is a pixel clock.
We can just skip the check when doing mem-to-mem writeback.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Mflag thresholds for all pipelines are set in dispc_init_mflag(), but we
are missing that for WB pipeline. Add WB configuration.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Fifo thresholds for all pipelines are set in dispc_init_fifos(), but we
are missing it for WB pipeline. Add that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Burst size for all pipelines is set in dispc_configure_burst_sizes(),
but we are missing WB pipe. So add that.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add handling of OMAP_DSS_CHANNEL_WB to dispc_ovl_set_channel_out() and
dispc_ovl_get_channel_out().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Refactor dispc_ovl_get_channel_out() to a bit cleaner form, which makes
it easier to add support for writeback in the following patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
At the moment we have a function to get the number of writeback
pipelines supported. However, the function is used in a wrong way,
causing a wrong pipeline to get configured when trying to use WB. Also,
we only have a single writeback pipeline on any of the DSS versions.
To fix and simplify this, create a 'has_writeback' flag into the dispc
driver, and after checking the flag, use OMAP_DSS_WB pipeline
explicitly when calling the configuration functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
OMAP5+ DSS has a writeback pipeline, but this was not specified in the
features list for OMAP5 DSS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Add dumping of the writeback registers to the register dump function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
DISPC_MFLAG_THRESHOLD_OFFSET() is missing the offset for WB. Add the
offset.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
By default DISPC asserts hsync and vsync sequentially, i.e. there's
first hsync and that is immediately followed by vsync. This is the only
available behaviour on OMAP2/3, and default behaviour on OMAP4+.
OMAP4+ has ALIGN bit in POL_FREQ register, which makes DISPC assert both
syncs at the same time.
It has been observed that some panels don't like sequential syncs (AM5
EVM's panel). After studying the datasheets for multiple panels and
encoders, and MIPI DPI spec, it looks like there is no standard way to
handle this.
Sometimes the datasheets don't mention the required syncs behaviour at
all, sometimes the datasheets have images that hint towards simultaneous
syncs, and sometimes it is explicitly mentioned that simultaneous syncs
are needed. No panels or encoders requiring sequential sync was found.
It thus seems to be safe to default to simultaneous syncs when the ALIGN
bit is available. This fixed AM5 EVM's panel, and no side effects have
been observed on other panels or encoders.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Update omapdss driver to set the state of the pins to:
- "default on resume
- "sleep" on suspend
By optionally putting the pins into sleep state in the suspend callback
we can accomplish two things.
- minimize current leakage from pins and thus save power,
- prevent the IP from driving pins output in an uncontrolled manner,
which may happen if the power domain drops the domain regulator.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- omap: fix hdmi audio configuration issue
- ssd1307fb: add ssd1309 support
- tridentfb: support DDC
- gxt4500: enable support for non-PPC platforms
* tag 'fbdev-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
radeonfb: Deinline large functions
gxt4500: enable panning
gxt4500: Use arch_phys_wc_* for framebuffer
gxt4500: fix color order
gxt4500: fix 16bpp 565 mode
gxt4500: enable on non-PPC architectures
tridentfb: Add DDC support
fb_ddc: Allow I2C adapters without SCL read capability
fbdev: ssd1307fb: add ssd1309 support
fbdev: ssd1307fb: alphabetize headers
video/omap: remove invalid check
OMAPDSS: hdmi: Reconfigure and restart audio when display is enabled
|
|
'spi/topic/omap-uwire', 'spi/topic/owner', 'spi/topic/pxa' and 'spi/topic/pxa2xx' into spi-next
|
|
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Drivers needs to export the OF id table and this be built into
the module or udev won't have the necessary information to autoload
the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This change is needed to properly lock I2C bus driver, which serves DDC.
Prior to this change i2c_put_adapter() is misused, which may lead to
an overflow over zero of I2C bus driver user counter.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Reconfigure and restart audio when display is enabled, if audio
playback was active before. This is needed in a situation when an
audio+video stream application opens the audio stream before the
video. When video stream is opened the display mode may change and
that aborts audio playback, because the display is momentarily
turned off.
The audio configuration is stored when it is successfully applied and
a boolean is set when the audio playback is started and unset when
stopped. This data is used to reconfigure the audio when display is
re-enabled. The audio playback is aborted if the reconfiguration fails.
A new spin lock is introduced in order to protect state variables
related to audio playback status. This is needed for the transition
from display enabled state (when audio start/stop commands can be
written to HW) to display disabled state (when audio start/stop
commands update only the hdmi.audio_playing variable) to always
serialize correctly with the start/stop audio commands. The already
existing mutex can not be used, because the audio start and stop
commands are executed in atomic context.
For example: when display is turned back on we take the spinlock and
we can be sure that the audio start/stop status will not change while
we update the HW according to hdmi.audio_playing state and set
hdmi.display_enabled to true. After releasing the lock
hdmi.display_enabled is true and all audio_start and audio_stop
commands write their stuff directly to HW.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
With two exceptions (drm/qxl and drm/radeon) all vm_operations_struct
structs should be constant.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Fix omap_dss_find_output_by_port_node() port parameter refcount
decrementation. The only user of dss_of_port_get_parent_device()
function is omap_dss_find_output_by_port_node() and it assumes the
refcount of the port parameter is not decremented by the call.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Fix node refcount leak in omapdss_of_get_next_port().
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
After the commit 736e60ddc215b85e73bbf7da26e1cde84cc9500f ("OMAPDSS:
componentize omapdss") the dss core device will wait until all the
subdevices have been successfully probed. However, we don't have a
working driver for RFBI, so if RFBI device exists, omapdss will never
get probed.
All the .dtsi files set RFBI as disabled, except am4372.dtsi. This
causes omapdss probe to not finish on AM4 devices.
This patch makes omapdss driver skip adding rfbi device as a
subcomponent, solving the issue.
This should be reverted when we have a working RFBI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Felipe Balbi <balbi@ti.com>
|
|
|
|
At the moment when HDMI video output is stopped, we just clear the
enable bit and return. While it's unclear if this can cause any issues,
I think it's still better to wait for FRAMEDONE interrupt after clearing
the enable bit so that we're sure the HDMI IP has finished.
As we don't have any ready-made irq handling for HDMI, and this only
needs to be done when disabling the HDMI output, this patch implements a
simple loop with sleep, polling the FRAMEDONE bit.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Error handling in hdmi_power_on_full() is not correct, and could leave
resources unfreed.
Fix this by arranging the error labels correctly.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Improve the DISPC debug print for scaling.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The current driver does both x and y decimation on OMAP3 DSS. Testing
shows that x decimation rarely works, leading to underflows.
The exact reason for this is unclear, as the underflows seem to happen
even with low pixel clock rates, and I would presume that if the DSS can
manage a display with 140MHz pixel clock, it could manage x decimation
with factor 2 with a low pixel clock (~30MHz).
So it is possible that there is a problem somewhere else, in memory
management, or DSS DMA, or similar. I have not found anything that would
help this.
So, to fix the downscaling scaling, this patch removes x decimation for
OMAP3. This will limit some of the more demanding downscaling scenarios,
but one could argue that using DSS to downscale such a large amount is
insane in the first place, as the produced image is rather bad quality.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The DISPC's scaling code seems to presume that decimation always
succeeds, and so we always do find a suitable downscaling setup.
However, this is not the case, and the algorithm can fail.
When that happens, the code just proceeds with wrong results, causing
issues later.
Add the necessary checks to bail out if the scaling algorithm failed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The DISPC driver uses 64 bit arithmetic to calculate the required clock
rate for scaling. The code does not seem to work correctly, and instead
calculates with 32 bit numbers, giving wrong result.
Fix the code by typecasting values to u64 first, so that the
calculations do happen in 64 bits.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
pixel_inc and row_inc work differently on OMAP2/3 and OMAP4+ DSS. On
OMAP2/3 DSS, the pixel_inc is _not_ added by the HW at the end of the
line, after the last pixel, whereas on OMAP4+ it is.
The driver currently works for OMAP4+, but does not handle OMAP2/3
correctly, which leads to tilted image when row_inc is used.
This patch adds a flag to DISPC driver so that the pixel_inc is added
when required.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
On OMAP3/AM43xx some scaling factors cause underflows/synclosts. After
studying this, I found that sometimes the driver uses three-tap scaling
with downscaling factor smaller than x0.5. This causes issues, as x0.5
is the limit for three-tap scaling.
The driver has FEAT_PARAM_DOWNSCALE parameter, but that seems to be for
five-tap scaling, which allows scaling down to x0.25.
This patch adds checks for both horizontal and vertical scaling. For
horizontal the HW always uses 5 taps, so the limit is x0.25.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
After calculating the required decimation for scaling, the dispc driver
checks once more if the resulting configuration is valid by calling
check_horiz_timing_omap3().
Earlier calls to this function have correctly used in_width and
in_height as parameters, but the last call uses width and height. This
causes the driver to possibly reject scaling that would work.
This patch fixes the parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
DISPC needs even input buffer width for YUV modes. The DISPC driver
doesn't check this at the moment (although omapdrm does), but worse,
when DISPC driver does x predecimation the result may be uneven. This
causes sometimes sync losts, underflows, or just visual errors.
This patch makes DISPC driver return an error if the user gives uneven
input width for a YUV buffer. It also makes the input width even in case
of predecimation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Errata i631 description:
"When in YUV4:2:0 format in 1D burst, the DISPC DMA skips lines when
fetching Chroma sampling."
Workaround:
"If YUV4:2:0-1D burst is required: Set
DISPC_VIDp_ATTRIBUTES[22]DOUBLESTRIDE to 0x0 and
DISPC_VIDp_ATTRIBUTES[13:12]ROTATION to 0x1 or 0x3"
The description is somewhat confusing, but testing has shown that DSS
fetches extra rows from memory when using NV12 format in 1D mode. If the
memory after the framebuffer is inaccessible, this leads to OCP errors.
The driver always uses DOUBLESTRIDE=0 when using 1D mode, so we only
need to handle the ROTATION part.
The issue exist on all OMAP4 and OMAP5 based DSS IPs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
|
|
Now that we are using components in omapdss, there's no need for
separate handling of dss and dispc driver init. Thus we can move the dss
and dispc init and unit func pointers to the lists we use for the other
dss submodules.
We can now also handle errors returned by the registration functions
properly: if registering a driver fails, we can stop processing and
return the error.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
omapdss kernel module contains drivers for multiple devices, one for
each DSS submodule. The probing we have at the moment is a mess, and
doesn't give us proper deferred probing nor ensure that all the devices
are probed before omapfb/omapdrm start using omapdss.
This patch solves the mess by using the component system for DSS
submodules.
The changes to all DSS submodules (dispc, dpi, dsi, hdmi4/5, rfbi, sdi,
venc) are the same: probe & remove functions are changed to bind &
unbind, and new probe & remove functions are added which call
component_add/del.
The dss_core driver (dss.c) acts as a component master. Adding and
matching the components is simple: all dss device's child devices are
added as components.
However, we do have some dependencies between the drivers. The order in
which they should be probed is reflected by the list in core.c
(dss_output_drv_reg_funcs). The drivers are registered in that order,
which causes the components to be added in that order, which makes the
components to be bound in that order. This feels a bit fragile, and we
probably should improve the code to manage binds in random order.
However, for now, this works fine.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
We have a list of function pointers to dss submodule uninit functions.
It makes sense to do the uninit in the reverse order to init, but that
is not currently the case.
This patch reorders the uninit calls to be the reverse of init order.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The following patches will add component handling to omapdss, improving
the handling of deferred probing. However, at the moment we're using
quite a lot of __inits and __exits in the driver, which prevent normal
dynamic probing and removal.
This patch removes most of the uses of __init and __exit, so that we can
register drivers after module init, and so that we can unregister
drivers even if the module is built-in.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The return value of dss_init_ports() is not handled at all, causing
crashes later if the call failed.
This patch adds the error handling, and we also move the call to a
slightly earlier place to make bailing out easier.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Refactor dss probe function by extracting the setup for video plls into
a separate function. The call to this function is also moved to a
slightly earlier phase, so that in error case we can bail out more
easily.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
We have a flag, 'dss_initialized', which tells omapfb and omapdrm if
omapdss is available. At the moment it can be set even if the dss
submodules are not all ready, in case something gets deferred.
Move the flag to dss_core driver so that it'll signal the availability
of the dss drivers move accurately.
For now, it'll signal that dss_core is ready, which is not quite correct
but still better than previously. The following patches will add
component system to omapdss, and after those patches 'dss_initialized'
will signal that all the submodules are ready.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Since kobject_init_and_add takes a format string, make sure that the
passed in name cannot be accidentally parsed.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
There is a constraint in the OMAP4 HDMI IP that requires to use
the 8-channel code when transmitting more than two channels.
The constraint doesn't apply for OMAP5 so don't force the channel
allocation in the sound driver as it can be done specifically for
OMAP4 later in the hdmi4 core.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
|
|
Downmix inhibit in HDMI_CORE_FC_AUDICONF3 register is in
bit 4 while CEA861_AUDIO_INFOFRAME_DB5_DM_INH sets bit 7.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
As per TRM, HDMI_WP_AUDIO_CFG[2] LEFT_BEFORE = 0 is reserved,
so it must always be set to 1 (the first sample is the left).
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
OMAP4 HDMI IP uses the 8-channel layout with 8-channel speaker
allocation mask when transmitting more than two channels. But
the channel count field (CC) of the Audio InfoFrame's DB1 is
not updated for 8-channels.
As per HDMI Compliance Test 7.31 "Audio InfoFrame", CC = 7 is
required for 8-channels CA masks (0x13 and 0x1F).
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Since 39b2bbe3d715 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Also make use of gpiod_get*_optional where applicable.
Apart from simplification of the affected drivers this is another step
towards making the flags argument to gpiod_get*() mandatory.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
