| Age | Commit message (Collapse) | Author |
|---|
|
This driver adds support for the max63{69,70,71,72,73,74} family of
watchdog timer chips.
It has been tested on an Arcom Zeus (max6369).
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Technologic Systems TS-72xx SBCs have external glue logic
CPLD which includes watchdog timer. This driver implements
kernel support for that.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The platform has never been fully merged
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Remove the old WDT implementation.
Signed-off-by: Albrecht Dreß <albrecht.dress@arcor.de>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
This patch adds support for the watchdog timer on Avionic Design Xanthos
boards.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The WM831x series of devices provide a watchdog with configurable
behaviour on timer expiry.
Currently this driver support refreshes via a register or GPIO line and
autonomous refreshes from a hardware source (eg, a clock).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Add watchdog device driver for the Nuvoton NUC900 series SoCs.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Add support for watchdog found on SBC-FITPC2 board.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
This add watchdog driver for broadcom 47xx device.
It uses the ssb subsytem to access embeded watchdog device.
Because the watchdog timeout is very short (about 2s), a soft timer is used
to increase the watchdog period.
Note : A patch for exporting the ssb_watchdog_timer_set will
be submitted on next linux-mips merge. Without this patch it can't
be build as a module.
Signed-off-by: Aleksandar Radovanovic <biblbroks@sezampro.rs>
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Tested-by: Florian Fainelli <florian@openwrt.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Add watchdog timer support for Freescale STMP3xxx boards
Signed-off-by: Vitaly Wool <vital@embeddedalley.com>
Signed-off-by: Dmitry Pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Implementation of twl4030 watchdog driver.
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@nokia.com>
Signed-off-by: Atal Shargorodsky <ext-atal.shargorodsky@nokia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This patch adds support for the U300 COH 901 327 watchdog for the
U300 platform recently added to RMK:s ARM tree.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Add support for PNX833x watchdog timer.
Signed-off-by: Daniel Laird <daniel.j.laird@nxp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The Orion watchdog driver is also used on Kirkwood.
Convention is to use orion5x for stuff specific to 88F5xxx Orion chips
and simply "orion" for shared stuff across SoCs including Kirkwood.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
|
|
Removes ARM26 sections from Kconfig and Makefile, because
ARM26 is long gone.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The FPGA based watchdog timer used by the Pika Warp appliance.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
GE Fanuc SBC610
Support for the FPGA based watchdog timer as found on GE Fanuc's SBC310,
SBC610 and PPC9A Single Board Computers.
This patch adds support for the watchdog timer found in one of the devices
FPGAs. There are two identical watchdog timers at different offsets in the
above mentioned boards, this driver is capable of supporting one of them.
The watchdog timers are also capable of generating interrupts at a
user-configurable threshold, though support for this operation is currently
not supported by the driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This driver implements support for the watchdog functionality provided
by the Wolfson Microelectronics WM8350, a multi-function audio and
power management subsystem intended for use in embedded systems. It is
based on a driver originally written by Graeme Gregory, though it has
been extensively modified since then.
Use of a GPIO to kick the watchdog is not yet supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Add a watchdog driver for the hardware watchdog timer on the
SMSC SCH3112, SCH3114 and SCH3116 Super IO chipset.
Tested-by: Marco Chiappero <marco@absence.it>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] orion5x_wdt.c: add spinlocking
[WATCHDOG] Orion: add hardware watchdog support
[WATCHDOG] omap_wdt.c: cleanup a bit omap_wdt.c
[WATCHDOG] omap_wdt.c: another ioremap() fix
[WATCHDOG] omap_wdt.c: sync linux-omap changes
[WATCHDOG] Add AT91SAM9X watchdog
[WATCHDOG] Add driver for winbond w83697ug/uf watchdog feature
[WATCHDOG] add watchdog driver IT8716 IT8726 IT8712J/K
|
|
This patch allows the use of the hardware watchdog in the
Marvell Orion series of ARM SoCs.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Add a driver for the watchdog timer embedded into AT91SAM9X chips.
Signed-off-by: Renaud Cerrato <r.cerrato@til-technologies.fr>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Adapted the w83627hf_wdt.c driver to work with the w83697ug/uf chip,
found on MSI Fuzzy CX700 boards.
The method used is taken directly from the winbond datasheet and
surprisingly it differs slightly from all the other winbond watchdogs.
So far it has only been tested on the CX700 board that I have, but it
seems to work nicely.
Signed-off-by: Flemming Frandsen <ff@nrvissing.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Add it87xx watchdog driver
IT8716 IT8718 IT8726 IT8712-J IT8712-K
Signed-off-by: Oliver Schuster <olivers137@aol.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
Conflicts:
arch/sparc64/kernel/pci_psycho.c
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The config stuff was already in drivers/watchdog/Kconfig
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add driver for the IDT RC32434 SoC built-in watchdog.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This patch adds support for the built-in RDC R-321x SoC watchdog.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The watchdog driver mpc8xx_wdt.c was a device interface to
arch/ppc/syslib/m8xx_wdt.c for MPC8xx hardware. Now that ARCH=ppc is
gone, this driver is of no more use. For ARCH=powerpc, MPC8xx hardware
is supported by mpc8xxx_wdt.c.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The problem is that iTCO_vendor_support.ko is still being built while
iTCO_vendor.h claims that its functions do not exist. The following
Makefile update fixes that. It causes iTCO_vendor_support.ko to no
longer be built if CONFIG_ITCO_VENDOR_SUPPORT=n.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
More coding style clean-up's.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Rename the driver because now we support some MPC86xx processors.
There are no changes to the mpc83xx_wdt.c file, yet. When possible, we do
file renames and changes separately (because Linus once asked so, because
it helps git to track the renamed files).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Trying to compile the v850 port brings many compile errors, one of them exists
since at least kernel 2.6.19.
There also seems to be noone willing to bring this port back into a usable
state.
This patch therefore removes the v850 port.
If anyone ever decides to revive the v850 port the code will still be
available from older kernels, and it wouldn't be impossible for the port to
reenter the kernel if it would become actively maintained again.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
After Linus fixed the inline assembly, the CFLAGS option is not
needed anymore.
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
To get this driver working we need the CFLAGS_hpwdt.o += -O in the Makefile.
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Add a watchdog timer based on the MFGPT timers in the CS5535/CS5536
companion chips to the AMD Geode GX and LX processors. Only caveat
is that the BIOS must provide at least a one free timer, and most
do not.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Hp is providing a Hardware WatchDog Timer driver that will only work with the
specific HW Timer located in the HP ProLiant iLO 2 ASIC. The iLO 2 HW Timer
will generate a Non-maskable Interrupt (NMI) 9 seconds before physically
resetting the server, by removing power, so that the event can be logged to
the HP Integrated Management Log (IML), a Non-Volatile Random Access Memory
(NVRAM). The logging of the event is performed using the HP ProLiant ROM via
an Industry Standard access known as a BIOS Service Directory Entry.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Support watchdog timers built into SiByte MIPS SoCs.
Signed-off-by: Andy Sharp <andy.sharp@onstor.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
This is a driver for watchdog timer built into TXx9 MIPS SoCs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Adds support for the built-in watchdog on EPIC Nano 7240 boards from IEI.
Tested on Nano-7240RS.
Hardware documentation of the platform (including watchdog) can be found
on the IEI website: http://www.ieiworld.com
Signed-off-by: Gilles Gigan <gilles.gigan@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This patch adds support for the ITE Tech Inc. IT8712F EC-LPC Super I/O
chipset found on many Pentium III and AMD motherboards. Developed using code
from other watchdog drivers and the datasheet on ITE Tech homepage.
Signed-off-by: Jorge Boncompte <jorge@dti2.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Driver for the watchdog timer. Still doesn't reboots the machine
on some boards, but we have improved and cleaned it
Signed-off-by: Matteo Croce <technoboy85@gmail.com>
Signed-off-by: Nicolas Thill <nico@openwrt.org>
Signed-off-by: Enrik Berkhan <Enrik.Berkhan@akk.org>
Signed-off-by: Christer Weinigel <wingel@nano-system.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
move watchdog tree from drivers/char/watchdog to drivers/watchdog.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
