summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2011-06-03rtlwifi: Fix logic in rx_interruptMike McCormack
Should pass along packet if there's no CRC and no hardware error. Signed-off-by: Mike McCormack <mikem@ring3k.org> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-03rtlwifi: Use write barrier when assigning ownershipMike McCormack
Make sure all updates to a descriptor are flushed to memory before assigning ownship to hardware. Signed-off-by: Mike McCormack <mikem@ring3k.org> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-03rtlwifi: Assign rx buffer ownership to hardware lastMike McCormack
Ownership of an rx buffer should only be given to the hardware after all other changes are written, otherwise there's a potential race. Signed-off-by: Mike McCormack <mikem@ring3k.org> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-03rtlwifi: Don't block interrupts in spinlocksMike McCormack
Now power state transitions are not called from an interrupt context, there's no need to block interrupts. This code appears to block interrupts for too long, causing my trackpad to lose sync occasionally. Signed-off-by: Mike McCormack <mikem@ring3k.org> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-03rtlwifi: Run IPS leave work in a taskletMike McCormack
This removes the need to use IRQ safe spinlocks in many places. Signed-off-by: Mike McCormack <mikem@ring3k.org> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-03rtlwifi: Store loop index in local variableMike McCormack
_rtl_pci_rx_interrupt uses rtlpci->rx_ring[rx_queue_idx].idx a few times, so store it in a separate variable. Signed-off-by: Mike McCormack <mikem@ring3k.org> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-03rtlwifi: Remove set_rfpowerstate_inprogressMike McCormack
set_rfpowerstate_inprogress is only set and never read so remove it. Signed-off-by: Mike McCormack <mikem@ring3k.org> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-03rtlwifi: Synchronize IRQ after disabling itMike McCormack
This make sure any IRQ handlers running on other CPUs complete. Signed-off-by: Mike McCormack <mikem@ring3k.org> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-02iwlagn: fix interface combinationsJohannes Berg
My patch to advertise interface combinations worked by pure luck in the P2P case, but all other cases are broken. This is due to a dumb mistake in the code that checks what should be advertised, fix that. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01iwlagn: change log to better represent the state of aggregation processWey-Yi Guy
Multiple A-MPDU actions will received from mac80211 while setting up the aggregation queue, change the message log to better represent the states. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01iwlagn: change the logging level for aggregation enable checkWey-Yi Guy
Aggregation will not enable if the traffic is lower than the threshold, this is not an error condition, so change the logging level. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01iwlagn: advertise interface combinationsJohannes Berg
With this, iwlwifi will advertise the limits on concurrency of virtual interfaces. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01iwlagn: free the ICT ISR when the request_irq failedEmmanuel Grumbach
Fix a memory leak in case request_irq fails. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01iwlwifi: disambiguate invalid DMA index warningsDaniel Halperin
The exact same error message is used in three different functions in iwlagn. Add the function name to the error string to disambiguate where the error is coming from. Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01iwlagn: solve sparse warningEmmanuel Grumbach
Remove local variable that was shadowing another one sta_priv hasn't changed since the beginning of the function, so don't define another pointer with the same name to the same variable Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01iwlagn: fix dual-mode RXONJohannes Berg
The PAN context has three states: disabled, disassociated and associated. It seems that wasn't quite as much of an issue in previous versions of the microcode, but now we really have to use all the three states properly. So add code to switch accordingly. Additionally, PAN parameters need to be sent differently and the timing for PAN RXON needs to be inbetween. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01iwlagn: remove un-necessary tx power opsWey-Yi Guy
All agn devices use the same tx power function, remove the ops Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01iwlagn: send tx power command if defer cause by RXON not matchWey-Yi Guy
During channge channel, tx power will not send to uCode, the tx power command should send after scan complete. but should also can send after RXON command. Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01ath9k: better position PAPRD debug messageMohammed Shafi Shajakhan
the training power calculation indirectly depends on target power under some scenarios, unless we have a valid training power, the PAPRD frames won't be sent out. so when we get an invalid training power, its better to display them before returning back. Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01ath9k: Add a debug entry to start/stop ANIMohammed Shafi Shajakhan
this helps the user to start/stop ANI dynamically. Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01ath9k: Further fix for mesh beaconingFabrice Deyber
This fix ensure the timers to be set at beacon interval boundaries. Without this change timers can be set improperly resulting in the absence of beacons. Signed-off-by: Fabrice Deyber <fabricedeyber@agilemesh.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01ath9k: wake up chip before initializing PAPRD tableMohammed Shafi Shajakhan
In PAPRD table initialization path we do some register read, so make sure the chip is awake during that. Currently PAPRD is disabled. Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01rtlwifi: rtl8192se: Synchronize IRQ after disabling itLarry Finger
As suggested by Mike McCormack <mikem@ring3k.org> for rtl8192ce, make sure any IRQ handlers running on other CPUs complete. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01rtlwifi: rtl8192se: Use write barrier when assigning ownershipLarry Finger
As noted by Mike McCormack <mikem@ring3k.org> for rtl8192ce, make sure all updates to a descriptor are flushed to memory before assigning ownship to hardware. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01mwifiex: remove support for old chipsets W0/W1Amitkumar Karwar
For SD8787 A0/A1 chipsets we use the default firmware image file 'mrvl/sd8787_uapsta.bin'. So the chip rev id variable is removed. The global variable fw_name is moved to adapter structure so that we can support a different interface, such as PCIe, in future. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01b43legacy: Fix warnings from gcc 4.6.0Larry Finger
gcc 4.6.0 warnings for b43legacy: CC [M] drivers/net/wireless/b43legacy/main.o drivers/net/wireless/b43legacy/main.c: In function ‘b43legacy_request_firmware’: drivers/net/wireless/b43legacy/main.c:1567:6: warning: variable ‘tmshigh’ set but not used [-Wunused-but-set-variable] drivers/net/wireless/b43legacy/main.c: In function ‘b43legacy_op_dev_config’: drivers/net/wireless/b43legacy/main.c:2637:6: warning: variable ‘antenna_rx’ set but not used [-Wunused-but-set-variable] drivers/net/wireless/b43legacy/main.c: In function ‘b43legacy_op_bss_info_changed’: drivers/net/wireless/b43legacy/main.c:2778:24: warning: variable ‘phy’ set but not used [-Wunused-but-set-variable] drivers/net/wireless/b43legacy/xmit.c: In function ‘generate_txhdr_fw3’: drivers/net/wireless/b43legacy/xmit.c:324:7: warning: variable ‘rts_rate_ofdm’ set but not used [-Wunused-but-set-variable] CC [M] drivers/net/wireless/b43legacy/dma.o drivers/net/wireless/b43legacy/dma.c: In function ‘free_all_descbuffers’: drivers/net/wireless/b43legacy/dma.c:820:36: warning: variable ‘desc’ set but not used [-Wunused-but-set-variable] drivers/net/wireless/b43legacy/dma.c: In function ‘b43legacy_dma_tx’: drivers/net/wireless/b43legacy/dma.c:1377:28: warning: variable ‘info’ set but not used [-Wunused-but-set-variable] drivers/net/wireless/b43legacy/dma.c:1374:24: warning: variable ‘hdr’ set but not used [-Wunused-but-set-variable] drivers/net/wireless/b43legacy/dma.c: In function ‘b43legacy_dma_handle_txstatus’: drivers/net/wireless/b43legacy/dma.c:1438:36: warning: variable ‘desc’ set but not used [-Wunused-but-set-variable] Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01rtl8192se: Fix warnings from gcc 4.6.0Larry Finger
gcc 4.6.0 warnings for rtl8192se: CC [M] drivers/net/wireless/rtlwifi/rtl8192se/dm.o drivers/net/wireless/rtlwifi/rtl8192se/dm.c: In function ‘_rtl92s_dm_refresh_rateadaptive_mask’: drivers/net/wireless/rtlwifi/rtl8192se/dm.c:225:5: warning: variable ‘rssi_level’ set but not used [-Wunused-but-set-variable] CC [M] drivers/net/wireless/rtlwifi/rtl8192se/fw.o drivers/net/wireless/rtlwifi/rtl8192se/fw.c: In function ‘rtl92s_download_fw’: drivers/net/wireless/rtlwifi/rtl8192se/fw.c:361:6: warning: variable ‘file_length’ set but not used [-Wunused-but-set-variable] CC [M] drivers/net/wireless/rtlwifi/rtl8192se/hw.o drivers/net/wireless/rtlwifi/rtl8192se/hw.c: In function ‘_rtl92se_hw_configure’: drivers/net/wireless/rtlwifi/rtl8192se/hw.c:887:6: warning: variable ‘reg_ratr’ set but not used [-Wunused-but-set-variable] drivers/net/wireless/rtlwifi/rtl8192se/hw.c: In function ‘_rtl92se_set_media_status’: drivers/net/wireless/rtlwifi/rtl8192se/hw.c:1125:20: warning: variable ‘ledaction’ set but not used [-Wunused-but-set-variable] drivers/net/wireless/rtlwifi/rtl8192se/hw.c: In function ‘rtl92se_gpio_radio_on_off_checking’: drivers/net/wireless/rtlwifi/rtl8192se/hw.c:2274:32: warning: variable ‘cur_rfstate’ set but not used [-Wunused-but-set-variable] CC [M] drivers/net/wireless/rtlwifi/rtl8192se/phy.o drivers/net/wireless/rtlwifi/rtl8192se/phy.c: In function ‘rtl92s_phy_set_bw_mode’: drivers/net/wireless/rtlwifi/rtl8192se/phy.c:266:5: warning: variable ‘reg_prsr_rsc’ set but not used [-Wunused-but-set-variable] CC [M] drivers/net/wireless/rtlwifi/rtl8192se/trx.o drivers/net/wireless/rtlwifi/rtl8192se/trx.c: In function ‘_rtl92se_translate_rx_signal_stuff’: drivers/net/wireless/rtlwifi/rtl8192se/trx.c:584:6: warning: variable ‘psaddr’ set but not used [-Wunused-but-set-variable] Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01rtl8192cu: Fix warnings from gcc 4.6.0Larry Finger
gcc 4.6.0 warnings for rtl8192cu: CC [M] drivers/net/wireless/rtlwifi/rtl8192cu/mac.o drivers/net/wireless/rtlwifi/rtl8192cu/mac.c: In function ‘rtl92c_translate_rx_signal_stuff’: drivers/net/wireless/rtlwifi/rtl8192cu/mac.c:1116:6: warning: variable ‘psaddr’ set but not used [-Wunused-but-set-variable] Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01rtl8192ce: Fix warnings from gcc 4.6.0Larry Finger
gcc 4.6.0 warnings for rtl8192ce: CC [M] drivers/net/wireless/rtlwifi/rtl8192ce/hw.o drivers/net/wireless/rtlwifi/rtl8192ce/hw.c: In function ‘_rtl92ce_hw_configure’: drivers/net/wireless/rtlwifi/rtl8192ce/hw.c:766:6: warning: variable ‘reg_ratr’ set but not used [-Wunused-but-set-variable] drivers/net/wireless/rtlwifi/rtl8192ce/hw.c: In function ‘rtl92ce_gpio_radio_on_off_checking’: drivers/net/wireless/rtlwifi/rtl8192ce/hw.c:1972:41: warning: variable ‘cur_rfstate’ set but not used [-Wunused-but-set-variable] CC [M] drivers/net/wireless/rtlwifi/rtl8192ce/phy.o drivers/net/wireless/rtlwifi/rtl8192ce/phy.c: In function ‘rtl92c_phy_config_rf_with_headerfile’: drivers/net/wireless/rtlwifi/rtl8192ce/phy.c:284:7: warning: variable ‘rtstatus’ set but not used [-Wunused-but-set-variable] CC [M] drivers/net/wireless/rtlwifi/rtl8192ce/trx.o drivers/net/wireless/rtlwifi/rtl8192ce/trx.c: In function ‘_rtl92ce_translate_rx_signal_stuff’: drivers/net/wireless/rtlwifi/rtl8192ce/trx.c:595:6: warning: variable ‘psaddr’ set but not used [-Wunused-but-set-variable] Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01rtl8192c-common: Fix warnings from gcc 4.6.0Larry Finger
gcc 4.6.0 warnings for rtl8192c-common: CC [M] drivers/net/wireless/rtlwifi/rtl8192c/fw_common.o drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c: In function ‘_rtl92c_cmd_send_packet’: drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c:549:5: warning: variable ‘own’ set but not used [-Wunused-but-set-variable] CC [M] drivers/net/wireless/rtlwifi/rtl8192c/phy_common.o drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c: In function ‘_rtl92c_phy_iq_calibrate’: drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:1256:6: warning: variable ‘bbvalue’ set but not used [-Wunused-but-set-variable] drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c: In function ‘rtl92c_phy_iq_calibrate’: drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:1766:6: warning: variable ‘reg_ecc’ set but not used [-Wunused-but-set-variable] drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c:1765:34: warning: variable ‘reg_eac’ set but not used [-Wunused-but-set-variable] Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01rtlwifi: Fix warnings from gcc 4.6.0Larry Finger
gcc 4.6.0 warnings for rtlwifi: CC [M] drivers/net/wireless/rtlwifi/base.o drivers/net/wireless/rtlwifi/base.c: In function ‘rtl_tx_agg_stop’: drivers/net/wireless/rtlwifi/base.c:891:23: warning: variable ‘tid_data’ set but not used [-Wunused-but-set-variable] drivers/net/wireless/rtlwifi/base.c: In function ‘rtl_tx_agg_oper’: drivers/net/wireless/rtlwifi/base.c:921:23: warning: variable ‘tid_data’ set but not used [-Wunused-but-set-variable] CC [M] drivers/net/wireless/rtlwifi/efuse.o drivers/net/wireless/rtlwifi/efuse.c: In function ‘efuse_pg_packet_write’: drivers/net/wireless/rtlwifi/efuse.c:928:24: warning: variable ‘dataempty’ set but not used [-Wunused-but-set-variable] drivers/net/wireless/rtlwifi/efuse.c: In function ‘efuse_get_current_size’: drivers/net/wireless/rtlwifi/efuse.c:1179:5: warning: variable ‘hoffset’ set but not used [-Wunused-but-set-variable] CC [M] drivers/net/wireless/rtlwifi/ps.o drivers/net/wireless/rtlwifi/ps.c: In function ‘rtl_ps_set_rf_state’: drivers/net/wireless/rtlwifi/ps.c:85:19: warning: variable ‘rtstate’ set but not used [-Wunused-but-set-variable] CC [M] drivers/net/wireless/rtlwifi/regd.o drivers/net/wireless/rtlwifi/regd.c: In function ‘_rtl_dump_channel_map’: drivers/net/wireless/rtlwifi/regd.c:310:28: warning: variable ‘ch’ set but not used [-Wunused-but-set-variable] CC [M] drivers/net/wireless/rtlwifi/usb.o drivers/net/wireless/rtlwifi/usb.c: In function ‘_rtl_usb_transmit’: drivers/net/wireless/rtlwifi/usb.c:826:21: warning: variable ‘urb_list’ set but not used [-Wunused-but-set-variable] drivers/net/wireless/rtlwifi/usb.c:825:23: warning: variable ‘skb_list’ set but not used [-Wunused-but-set-variable] Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01b43: Fix warnings from gcc 4.6.0Larry Finger
gcc 4.6.0 warnings for b43: CC [M] drivers/net/wireless/b43/lo.o drivers/net/wireless/b43/lo.c: In function ‘lo_measure_gain_values’: drivers/net/wireless/b43/lo.c:304:7: warning: variable ‘trsw_rx’ set but not used [-Wunused-but-set-variable] CC [M] drivers/net/wireless/b43/dma.o drivers/net/wireless/b43/dma.c: In function ‘free_all_descbuffers’: drivers/net/wireless/b43/dma.c:760:30: warning: variable ‘desc’ set but not used [-Wunused-but-set-variable] drivers/net/wireless/b43/dma.c: In function ‘b43_dma_handle_txstatus’: drivers/net/wireless/b43/dma.c:1391:30: warning: variable ‘desc’ set but not used [-Wunused-but-set-variable] Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01ath9k: Handle IBSS status changes in BSS_CHANGED_IBSSRajkumar Manoharan
Configure ibss node's bss_changes under BSS_CHANGED_IBSS. And also start/stop ani timer only if the station join/leave the group. Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01ath9k: Remove ATH9K_BEACON_PERIOD maskRajkumar Manoharan
Earlier beacon_interval is used to hold interval value and some flags (ATH9K_BEACON_ENA &ATH9K_BEACON_PERIOD). So to extract interval ATH9K_BEACON_PERIOD is used. Those flags were completely removed. So masking beacon_interval is not required. Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01bcma: host pci: implement block R/W operationsRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01b43: bus: add helpers for checking host typeRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01b43: use new pointers path to access ssb_device in SSB specific placesRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01b43: SDIO: use new pointers path to access ssb_deviceRafał Miłecki
SDIO code is SSB specific, we can safely just use "sdev" Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01b43: LP-PHY: use new pointers path to access ssb_deviceRafał Miłecki
LP-PHY code is SSB specific, add check for bus type. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01ath9k: mark few functions as staticMohammed Shafi Shajakhan
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01ath9k: make ath9k_setpower function as staticMohammed Shafi Shajakhan
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01bcma: pci: implement interrupts controlRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01ath9k_hw: remove ath9k_hw_get_desc_linkFelix Fietkau
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01ath9k: unify edma and non-edma tx code, improve tx fifo handlingFelix Fietkau
EDMA based chips (AR9380+) have 8 Tx FIFO slots, which are used to fix the tx queue start/stop race conditions which have to be worked around for earlier chips by keeping the last descriptor in the queue. The current code stores all frames that do not fit onto the 8 FIFO slots in a separate list. Whenever a FIFO slot is freed up, the next frame (or A-MPDU) from the pending queue gets moved to that slot. This process is not only inefficient, but also unnecessary. The code can be improved visibly by keeping the pending queue fully linked, and moving the contents of the entire queue to a FIFO slot as it becomes available. This patch makes the necessary changes for that and also merges some code that was duplicated for EDMA vs non-EDMA. It changes txq->axq_link to point to the last descriptor instead of the link pointer, so that ath9k_hw_set_desc_link can be used, which works on all chips. With this patch, a small performance increase for non-aggregated traffic was observed on AR9380 based embedded hardware. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01ath9k: remove redundant if checkMohammed Shafi Shajakhan
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01mac80211_hwsim driver support userspace frame tx/rxJavier Lopez
This patch adds to mac80211_hwsim the capability to send traffic via userspace. Frame exchange between kernel and user spaces is done through generic netlink communication protocol. A new generic netlink family MAC80211_HWSIM is proposed, this family contains three basic commands HWSIM_CMD_REGISTER, which is the command used to register a new traffic listener, HWSIM_CMD_FRAME, to exchange the frames from kernel to user and vice-versa, and HWSIM_CMD_TX_INFO_FRAME which returns from user all the information about retransmissions, rates, rx signal, and so on. How it works: Once the driver is loaded the MAC80211_HWSIM family will be registered. In the absence of userspace daemon, the driver itselfs implements a perfect wireless medium as it did in the past. When a daemon sends a HWSIM_CMD_REGISTER command, the module stores the application PID, and from this moment all frames will be sent to the registered daemon. The user space application will be in charge of process/forward all frames broadcast by any mac80211_hwsim radio. If the user application is stopped, the kernel module will detect the release of the socket and it will switch back to in-kernel perfect channel simulation. The userspace daemon must be waiting for incoming HWSIM_CMD_FRAME commands sent from kernel, for each HWSIM_CMD_FRAME command the application will try to broadcast this frame to all mac80211_hwsim radios, however the application may decide to forward/drop this frame. In the case of forwarding the frame, a new HWSIM_CMD_FRAME command will be created, all necessary attributes will be populated and the frame will be sent back to the kernel. Also after the frame broadcast phase, a HWSIM_CMD_TX_INFO_FRAME command will be sent from userspace to kernel, this command contains all the information regarding the transmission, such as number of tries, rates, ack signal, etc. You can find the actual implementation of wireless mediumd daemon (wmediumd) at: * Last version tarball: https://github.com/jlopex/cozybit/tarball/master * Or visiting my github tree: https://github.com/jlopex/cozybit/tree Signed-off-by: Javier Lopez <jlopex@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01rt2x00: Enabled rt35xx device support by default.Gertjan van Wingerde
Now that support for these devices has been added we can enable them by default and remove the Kconfig not on support for these devices to be non-functional. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01rt2x00: Move rt2800_txdone and rt2800_txdone_entry_check to rt2800usb.Gertjan van Wingerde
These two functions are only used by rt2800usb so they don't have to be in rt2800lib. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01rt2x00: Interface sequence lock doesn't have to disable interrupts.Gertjan van Wingerde
This lock is only used in the TX path and thus in process context. Therefore we can use a much lighter spinlock variant. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-01rt2x00: Add support for RT3572/RT3592/RT3592+Bluetooth combo cardGertjan van Wingerde
(based on an earlier patch submitted by Shiang) Add support for RT3572/RT3592/RT3592+Bluetooth combo card Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v0.10.2 at 2024-10-22 02:46:36 (GMT)