| Age | Commit message (Collapse) | Author |
|---|
|
Use the normal #define to help grep find mac addresses
and ensure that addresses are aligned.
pasemi.h has an unaligned access to mac_addr, unchanged
for now.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Olof Johansson <olof@lixom.net> # pasemi_mac pieces
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
interface
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Driver firmware mailbox interface was operating in polling mode
because of limitations with the earlier versions of 83xx adapter firmware.
These issues are resolved and we are implementing interrupt based mailbox
mechanism.
o Data structures and API's for interrupt mode mailbox mechanism.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Enhanced the driver to use standard Linux error codes
o Return a unique error code to indicate loopback is in progress
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch does the initial bonding conversion to RCU. After it the
following modes are protected by RCU alone: roundrobin, active-backup,
broadcast and xor. Modes ALB/TLB and 3ad still acquire bond->lock for
reading, and will be dealt with later. curr_active_slave needs to be
dereferenced via rcu in the converted modes because the only thing
protecting the slave after this patch is rcu_read_lock, so we need the
proper barrier for weakly ordered archs and to make sure we don't have
stale pointer. It's not tagged with __rcu yet because there's still work
to be done to remove the curr_slave_lock, so sparse will complain when
rcu_assign_pointer and rcu_dereference are used, but the alternative to use
rcu_dereference_protected would've created much bigger code churn which is
more difficult to test and review. That will be converted in time.
1. Active-backup mode
1.1 Perf recording while doing iperf -P 4
- old bonding: iperf spent 0.55% in bonding, system spent 0.29% CPU
in bonding
- new bonding: iperf spent 0.29% in bonding, system spent 0.15% CPU
in bonding
1.2. Bandwidth measurements
- old bonding: 16.1 gbps consistently
- new bonding: 17.5 gbps consistently
2. Round-robin mode
2.1 Perf recording while doing iperf -P 4
- old bonding: iperf spent 0.51% in bonding, system spent 0.24% CPU
in bonding
- new bonding: iperf spent 0.16% in bonding, system spent 0.11% CPU
in bonding
2.2 Bandwidth measurements
- old bonding: 8 gbps (variable due to packet reorderings)
- new bonding: 10 gbps (variable due to packet reorderings)
Of course the latency has improved in all converted modes, and moreover
while
doing enslave/release (since it doesn't affect tx anymore).
Also I've stress tested all modes doing enslave/release in a loop while
transmitting traffic.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I factored out the tx xmit code which relies on slave id in
bond_xmit_slave_id. It is global because later it can be used also in
3ad mode xmit. Unnecessary obvious comments are removed. Active-backup
mode is simplified because bond_dev_queue_xmit always consumes the skb.
bond_xmit_xor becomes one line because of bond_xmit_slave_id.
bond_for_each_slave_from is not used in bond_xmit_slave_id because later
when RCU is used we can avoid important race condition by using standard
rculist routines.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't need to start from the curr_active_slave as the frame will be
sent to all eligible slaves anyway, so we remove the unnecessary local
variables, checks and comments, and make it use the standard list API.
This has the nice side-effect that later when it's converted to RCU
a race condition will be avoided which could lead to double packet tx.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In all the cases we already hold bond->lock for reading, so the slave
can't get away and the check != NULL is sufficient. curr_active_slave
can still change after the read_lock is unlocked prior to use of the
dereferenced value, so there's no need for it. It either contains a
valid slave which we use (and can't get away), or it is NULL which is
checked.
In some places the read_lock of curr_slave_lock was left because we need
it not to change while performing some action (e.g. syncing current
active slave's addresses, sending ARP requests through the active slave)
such cases will be dealt with individually while converting to RCU.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch aims to remove struct bonding's first_slave and struct
slave's next and prev pointers, and replace them with the standard Linux
list API. The old macros are converted to list API as well and some new
primitives are available now. The checks if there're slaves that used
slave_cnt have been replaced by the list_empty macro.
Also a few small style fixes, changing longest -> shortest line in local
variable declarations, leaving an empty line before return and removing
unnecessary brackets.
This is the first step to gradual RCU conversion.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Kleine-Budde says:
====================
this is a pull-request for net-next/master. It consists of two patches
by Fabio Estevam. Them first convert the flexcan driver to use
devm_ioremap_resource(), the second adds return value checking for
clk_prepare_enable().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On very rare occasions, repeated load/unload stress test in the presence of
our storage driver (bnx2i/bnx2fc) causes a kernel panic in bnx2x code
(NULL pointer dereference). Stack traces indicate the issue happens during MAC
configuration; thorough code review showed that indeed several races exist
in which one thread can iterate over the list of configured MACs while another
deletes entries from the same list.
This patch adds a varient on the single-writer/Multiple-reader lock mechanism -
It utilizes an already exsiting bottom-half lock, using it so that Whenever
a writer is unable to continue due to the existence of another writer/reader,
it pends its request for future deliverance.
The writer / last readers will check for the existence of such requests and
perform them instead of the original initiator.
This prevents the writer from having to sleep while waiting for the lock
to be accessible, which might cause deadlocks given the locks already
held by the writer.
Another result of this patch is that setting of Rx Mode is now made in
sleepable context - Setting of Rx Mode is made under a bottom-half lock, which
was always nontrivial for the bnx2x driver, as the HW/FW configuration requires
wait for completions.
Since sleep was impossible (due to the sleepless-context), various mechanisms
were utilized to prevent the calling thread from sleep, but the truth was that
when the caller thread (i.e, the one calling ndo_set_rx_mode()) returned, the
Rx mode was still not set in HW/FW.
bnx2x_set_rx_mode() will now overtly schedule for the Rx changes to be
configured by the sp_rtnl_task which hold the RTNL lock and is sleepable
context.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 4aa5dee4d9 ("net: convert resend IGMP to notifier event")
we try to acquire rtnl in bond_resend_igmp_join_requests but it can be
scheduled with rtnl already held (e.g. when bond_change_active_slave is
called with rtnl) causing a loop of immediate reschedules + calls because
rtnl_trylock fails each time since it's being already held.
For me this issue leads to system hangs very easy:
modprobe bonding; ifconfig bond0 up; ifenslave bond0 eth0; rmmod
bonding;
The fix is to introduce a small (1 jiffy) delay which is enough for the
sections holding rtnl to finish without putting any strain on the system.
Also adjust the timer in bond_change_active_slave to be 1 jiffy, since
most of the time it's called with rtnl already held.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The initial driver support was for a single mPIPE shim on the chip
(as is the case for the Gx36 hardware). The Gx72 chip has two mPIPE
shims, so we extend the driver to handle that case.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code used to call napi_disable() in an interrupt handler
(from smp_call_function), which in turn could call msleep().
Unfortunately you can't sleep in an interrupt context.
Luckily it turns out all the NAPI support functions are
just operating on data structures and not on any deeply
per-cpu data, so we can arrange to set up and tear down all
the NAPI state on the core driving the process, and just
do the IRQ enable/disable as a smp_call_function thing.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Building against headers from an older Tilera hypervisor can cause
the frags[] array to be overrun. Don't enable TSO in that case.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change allows the user to configure various features of the tile
networking drivers on and off. There is no change to the default
initialization state of either the tilegx or tilepro drivers.
Neither driver needs the ndo_fix_features or ndo_set_features callbacks,
since the generic code already handles the dependencies for
fix_features, and there is no hardware state to tweak in set_features.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
grp->grp_id is obsolete. It has no use in the current driver.
Remove it from gfar_priv_grp and put the 'rstat' member
in its place, in the 2nd cache line, as rstat needs fast access.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Using devm_ioremap_resource() can make the code simpler and smaller.
Also, place alloc_candev() after of_match_device() to make error handling
easier.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The RFE interrupt is enabled for the r8a7790 but isn't handled,
resulting in the interrupts core noticing unhandled interrupts, and
eventually disabling the ethernet IRQ.
Fix it by adding RFE to the bitmask of error interrupts to be handled
for r8a7790.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
This series contains updates to ixgbe and pci.
The first patch for ixgbe from Greg Rose is the second submission. The
first submission of "ixgbe: Retain VLAN filtering in promiscuous + VT
mode" had a typo, which Joe Perches pointed out and is fixed in this
submission.
Alex updates the ixgbe driver to use the generic helper pci_vfs_assigned
instead of the driver specific function ixgbe_vfs_are_assigned.
Don Skidmore provides 4 patches for ixgbe, the first being a fix for
flow control ethtool reporting. Originally ixgbe_device_supports_autoneg_fc()
was expected to be called by only copper devices, which lead to false
information being displayed via ethtool. Two other patches add support
for fixed fiber for SFP+ devices and the addition of a quad-port x520
adapter. The last patch simply bumps the driver version.
Emil Tantilov provides 3 fixes for ixgbe, two of which resolve
semaphore lock issues. The third fix resolves several issues in the
previous implementation of the SFF data dumps of SFP+ modules.
The remaining ixgbe and pci patches are from Jacob Keller. The pci
patches exposes bus speed, link speed and bus width so that drivers
can take advantage of this information. In addition, adds a pci function
which obtains minimum link width and speed. Jacob also provides the
ixgbe patch to incorporate the pci function. He provides a patch that
fixes a lockdep issue created due to ixgbe_ptp_stop always running
cancel_work_sync even if the work item had not been created properly with
INIT_WORK. This issue was found and reported by Stephen Hemminger.
-v2-
* fix patch 3 to be a bool function based on David Miller's feedback
* fix patch 4 debug message based on David Miller's feedback
* fix patch 8 moved the extern declarations to pci.h based on Bjorn
Helgaas's feedback
* fix patch 11 update the error message to include encoding loss based
* fix patch 8/9/10 title based on Bjorn's feedback
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a x520 based quad-port (4x10Gbps) NIC with a single QSFP+
connector. Changes were required to our identify functions due to
different eeprom address which is also included here.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch changes the error code path in ixgbe_acquire_swfw_sync() to deal
with cases where acquiring SW semaphore times out.
In cases where the SW/FW semaphore bits were set (i.e. due to a crash) the
driver will hang on load. With this patch the driver will clear
the stuck bits if the semaphore was not acquired in the allotted time.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch renames the stats introduced by the busy poll feature so that they
are more inline with the current statistics naming schemes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes a lockdep issue created due to ixgbe_ptp_stop always running
cancel_work_sync even if the work item had not been created properly with
INIT_WORK. This is caused because ixgbe_ptp_stop did not check to actually
ensure PTP was running first. The new implementation introduces a state in the
&adapter->state field which is used to indicate that PTP is running. (This
replaces the IXGBE_FLAG2_PTP_ENABLED field). This state will use the atomic
set_bit, test_bit, and test_and_clear_bit functions. ixgbe_ptp_stop will check
to ensure that PTP was enabled, (and if not, it will not attempt to do any
cleanup work from ixgbe_ptp_init). This resolves the lockdep annotation warning
found by Stephen Hemminger
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch uses the new pcie_get_minimum_link function to perform a check to
ensure that the adapter is hooked into a slot which is capable of providing the
necessary bandwidth. This check supersedes the original method which only
checked the current pci device. The new method is capable of determining the
minimum speed and link of an entire PCI chain.
-v2-
* update the error message to include encoding loss
CC: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
A PCI Express device can potentially report a link width and speed which it will
not properly fulfill due to being plugged into a slower link higher in the
chain. This function walks up the PCI bus chain and calculates the minimum link
width and speed of this entire chain. This can be useful to enable a device to
determine if it has enough bandwidth for optimum functionality.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
pcie_link_speed and pcix_bus_speed are arrays used by probe.c to correctly
convert lnksta register values into the pci_bus_speed enum. These static arrays
are useful outside probe for this purpose. This patch makes these defines into
conist arrays and exposes them with an extern header in drivers/pci/pci.h
-v2-
* move extern declarations to drivers/pci/pci.h
CC: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch fixes several issues with the previous implementation of the
SFF data dump of SFP+ modules:
- removed the __IXGBE_READ_I2C flag - I2C access locking is handled in the
HW specific routines
- fixed the read loop to read data from ee->offset to ee->len
- the reads fail if __IXGBE_IN_SFP_INIT is set in the process - this is
needed because on some HW I2C operations can take long time and disrupt
the SFP and link detection process
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
ixgbe_read/write_i2c_phy_82598() does not hold the SWFW_SYNC
semaphore for the entire function. Instead the lock is held only
during the phy.ops.read/write_reg operations. As result when the
function is being called simultaneously the I2C read/writes can
be corrupted.
The following patch introduces the SWFW_SYNC semaphore for the
entire ixgbe_read/write_i2c_phy_82598() function. To accomplish
this I had to create 2 separate functions:
ixgbe_read_phy_reg_mdi()
ixgbe_write_phy_reg_mdi()
Those functions are identical to ixgbe_read/write_phy_reg_generic()
sans the locking, and can be used in ixgbe_read/write_i2c_phy_82598()
with the SWFW_SYNC semaphore being held.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Bump the version number to better match with a similar version of the
out of tree driver.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds support for a new media type fiber_fixed. This is useful
to avoid all the SFP+ hot plug support path on devices who's fix fiber need
not worry about such things. This patch is needed for a following patch
that adds support for "fiber_fixed" devices.
v2: cleaned up logging message based on feedback from David Miller
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Originally ixgbe_device_supports_autoneg_fc() was only expected to
be called by copper devices. This would lead to false information
to be displayed via ethtool.
v2: changed ixgbe_device_supports_autoneg_fc() to a bool function,
it returns bool. Based on feedback from David Miller
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change makes it so that the ixgbe driver uses the generic helper
pci_vfs_assigned instead of the ixgbe specific function
ixgbe_vfs_are_assigned.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When using the new bridge FDB interface to allow SR-IOV virtual function
network devices to communicate with SW bridged network devices the
physical function is placed into promiscuous mode and hardware VLAN
filtering is disabled. This defeats the ability to use VLAN tagging
to isolate user networks. When the device is in promiscuous mode and
VT mode simultaneously ensure that VLAN hardware filtering remains
enabled.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use the "swap descriptor" feature of the hardware to properly swap the
descriptors when running in big endian mode. Since the swapping occurs
on 64 bits words, we also need to provide a separate structure layout
for the DMA descriptors between little endian and big endian mode,
like is done in the mv643xx_eth driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The macros used for the various fields of the RX and TX descriptions
are currently declared next to those fields within the structure
definitions of the RX and TX descriptors.
However, in order to support big endian, we'll have to use the "swap
descriptors" features of the hardware, which swaps every byte within
each 64 bits word of the descriptors. This requires a separate
definition of the RX and TX descriptor structures for little and big
endian, as is done in the mv643xx_eth. Those macros can therefore no
longer be defined inside those structures.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding support for setting MAC address to cpsw device via ndo_set_mac_address
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
