| Age | Commit message (Collapse) | Author |
|---|
|
The I2C core always reports the MODALIAS uevent as "i2c:<modalias>"
regardless of the mechanism that was used to register the device
(i.e: OF or board code) and the table that is used later to match
the driver with the device (i.e: I2C id table or OF match table).
So drivers needs to export the I2C id table and this be built into
the module or udev won't have the necessary information to autoload
the needed driver module when the device is added.
But this means that OF-only drivers needs to have both OF and I2C id
tables that have to be kept in sync and also the dev node compatible
manufacturer prefix is stripped when reporting the MODALIAS. Which can
lead to issues if two vendors use the same I2C device name for example.
To avoid the above, the I2C core behavior may be changed in the future
to not require an SPI device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table even when
is unused now to prevent breaking module loading when the core changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Currently, lp55xx_of_populate_pdata() allocates lp55xx_platform_data if
it's null. And it parses the DT and copies values into the
'client->dev.platform_data'. This may have architectural issue.
Platform data is configurable through the DT or I2C board info inside the
platform area. However, lp55xx common driver changes this configuration
when it is loaded. So 'client->dev.platform_data' is not null anymore.
Eventually, the driver initialization is not identical when it's unloaded
and loaded again.
The lp55xx common driver should use the private data, 'lp55xx_chip->pdata'
instead of changing the original platform data.
So, lp55xx_of_populate_pdata() is modified as follows.
* Do not update 'dev->platform_data'. Return the pointer of new allocated
lp55xx_platform_data. Then the driver points it to private data,
'lp55xx_chip->pdata'.
* Each lp55xx driver checks the pointer and handles an error case.
Then, original platform data configuration will be kept regardless of
loading or unloading the driver.
The driver allocates the memory and copies them from the DT if it's NULL.
After the driver is loaded again, 'client->dev.platform_data' is same as
initial load, so the driver is initialized identically.
Cc: Toshi Kikuchi <toshik@chromium.org>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
syscon_node_to_regmap() returns a regmap or an ERR_PTR().
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Use resource-managed function devm_led_classdev_register instead
of led_classdev_register to make the error-path simpler.
To be compatible with the change, various gotos are replaced with
direct returns and unneeded labels are dropped. Also, remove
fsg_led_remove as it is now redundant.
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Devices found by class_find_device must be freed with put_device().
Otherwise the reference count will not work properly.
Fixes: a96aa64cb572 ("leds/led-class: Handle LEDs with the same name")
Reported-by: Alan Tull <delicious.quinoa@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This checking is done by regmap_get_i2c_bus() which is called in
devm_regmap_init_i2c().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
The leds-ns2 driver is also used by the n090401 board (Seagate NAS
4-Bay), which is based on the Marvell Armada-370 SoC.
Then this patch allows to select the leds-ns2 driver if MACH_ARMADA_370
is enabled. Additionally, this also updates the Kconfig help message.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
On the board n090401 (Seagate NAS 4-Bay), some of the LEDs are handled
by the leds-ns2 driver. This LEDs are connected to an I2C GPIO expander
(PCA95554PW) which means that GPIO access may sleep. This patch makes
leds-ns2 compatible with such GPIOs by using the *_cansleep() variant of
the GPIO functions. As a drawback this functions can't be used safely in
a timer context (with the timer LED trigger for example). To fix this
issue, a workqueue mechanism (copied from the leds-gpio driver) is used.
Note that this patch also updates slightly the ns2_led_sata_store
function. The LED state is now retrieved from cached values instead of
reading the GPIOs previously. This prevents ns2_led_sata_store from
working with a stale LED state (which may happen when a delayed work
is pending).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
On the board n090401 (Seagate NAS 4-Bay), the LED mode mapping (GPIO
values to LED mode) is different from the one used on other boards
supported by the leds-ns2 driver.
With this patch the hardcoded mapping is removed from leds-ns2. Now,
it must be defined either in the platform data (if an old-fashion board
setup file is used) or in the DT node. In order to allow the later, this
patch also introduces a modes-map property for the leds-ns2 DT binding.
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
These reg_default tables are not modified after initialized, so make them
const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
If COMPILE_TEST is enabled, relax the dependency on GPIOLIB for the
recently introduced symbols LEDS_AAT1290 and LEDS_KTD2692.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fix MSI/MSI-X on pseries from Guilherme"
* tag 'powerpc-4.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/PCI: Disable MSI/MSI-X interrupts at PCI probe time in OF case
PCI: Make pci_msi_setup_pci_dev() non-static for use by arch code
|
|
Pull networking fixes from David Miller:
"Some straggler bug fixes here:
1) Netlink_sendmsg() doesn't check iterator type properly in mmap
case, from Ken-ichirou MATSUZAWA.
2) Don't sleep in atomic context in bcmgenet driver, from Florian
Fainelli.
3) The pfkey_broadcast() code patch can't actually ever use anything
other than GFP_ATOMIC. And the cases that right now pass
GFP_KERNEL or similar will currently trigger an RCU splat. Just
use GFP_ATOMIC unconditionally. From David Ahern.
4) Fix FD bit timings handling in pcan_usb driver, from Marc
Kleine-Budde.
5) Cache dst leaked in ip6_gre tunnel removal, fix from Huaibin Wang.
6) Traversal into drivers/net/ethernet/renesas should be triggered by
CONFIG_NET_VENDOR_RENESAS, not a particular driver's config
option. From Kazuya Mizuguchi.
7) Fix regression in handling of igmp_join errors in vxlan, from
Marcelo Ricardo Leitner.
8) Make phy_{read,write}_mmd_indirect() properly take the mdio_lock
mutex when programming the registers. From Russell King.
9) Fix non-forced handling in u32_destroy(), from WANG Cong.
10) Test the EVENT_NO_RUNTIME_PM flag before it is cleared in
usbnet_stop(), from Eugene Shatokhin.
11) In sfc driver, don't fetch statistics firmware isn't capable of,
from Bert Kenward.
12) Verify ASCONF address parameter location in SCTP, from Xin Long"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
sctp: donot reset the overall_error_count in SHUTDOWN_RECEIVE state
sctp: asconf's process should verify address parameter is in the beginning
sfc: only use vadaptor stats if firmware is capable
net: phy: fixed: propagate fixed link values to struct
usbnet: Get EVENT_NO_RUNTIME_PM bit before it is cleared
drivers: net: xgene: fix: Oops in linkwatch_fire_event
cls_u32: complete the check for non-forced case in u32_destroy()
net: fec: use reinit_completion() in mdio accessor functions
net: phy: add locking to phy_read_mmd_indirect()/phy_write_mmd_indirect()
vxlan: re-ignore EADDRINUSE from igmp_join
net: compile renesas directory if NET_VENDOR_RENESAS is configured
ip6_gre: release cached dst on tunnel removal
phylib: Make PHYs children of their MDIO bus, not the bus' parent.
can: pcan_usb: don't provide CAN FD bittimings by non-FD adapters
net: Fix RCU splat in af_key
net: bcmgenet: fix uncleaned dma flags
net: bcmgenet: Avoid sleeping in bcmgenet_timeout
netlink: mmap: fix tx type check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull nvdimm fixlet from Dan Williams:
"This is a libnvdimm ABI fixup.
I pushed back on this change quite hard given the late date, that it
appears to be purely cosmetic, sysfs is not necessarily meant to be a
user friendly UI, and the kernel interprets the reversed polarity of
the ACPI_NFIT_MEM_ARMED flag correctly. When this flag is set, the
energy source of an NVDIMM is not armed and any new writes to the DIMM
may not be preserved.
However, Bob Moore warned me that it is important to get these things
named correctly wherever they appear otherwise we run the risk of a
less than cautious firmware engineer implementing the polarity the
wrong way. Once a mistake like that escapes into production platforms
the flag becomes useless and we need to move to a new bit position.
Bob has agreed to take a change through ACPICA to rename
ACPI_NFIT_MEM_ARMED to ACPI_NFIT_MEM_NOT_ARMED, and the patch below
from Toshi brings the sysfs representation of these flags in line with
their respective polarities.
Please pull for 4.2 as this is the first kernel to expose the ACPI
NFIT sysfs representation, and this is likely a kernel that firmware
developers will be using for checking out their NVDIMM enabling"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: Clarify memory device state flags strings
|
|
enable pause interrupt should use SPI_CMD_PAUSE_IE MACRO,
so fix it.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit d5e136a21b2028fb1f45143ea7112d5869bfc6c7 ("clk: samsung: Register
clk provider only after registering its all clocks", merged to v3.17-rc1)
modified a way that driver registers registers to core framework. This
change has not been applied to s5pv210 clocks driver, which has been
merged in parallel to that commit. This patch adds a missing call to
samsung_clk_of_add_provider(), so the driver is operational again.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: stable@vger.kernel.org # v3.17+
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
ACPI 6.0 NFIT Memory Device State Flags in Table 5-129 defines
NVDIMM status as follows. These bits indicate multiple info,
such as failures, pending event, and capability.
Bit [0] set to 1 to indicate that the previous SAVE to the
Memory Device failed.
Bit [1] set to 1 to indicate that the last RESTORE from the
Memory Device failed.
Bit [2] set to 1 to indicate that platform flush of data to
Memory Device failed. As a result, the restored data content
may be inconsistent even if SAVE and RESTORE do not indicate
failure.
Bit [3] set to 1 to indicate that the Memory Device is observed
to be not armed prior to OSPM hand off. A Memory Device is
considered armed if it is able to accept persistent writes.
Bit [4] set to 1 to indicate that the Memory Device observed
SMART and health events prior to OSPM handoff.
/sys/bus/nd/devices/nmemX/nfit/flags shows this flags info.
The output strings associated with the bits are "save", "restore",
"smart", etc., which can be confusing as they may be interpreted
as positive status, i.e. save succeeded.
Change also the dev_info() message in acpi_nfit_register_dimms()
to be consistent with the sysfs flags strings.
Reported-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
[ross: rename 'not_arm' to 'not_armed']
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
[djbw: defer adding bit5, HEALTH_ENABLED, for now]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Some of the stats handling code differs based on SR-IOV support,
and SRIOV support is only available if full-featured firmware is
used.
Do not use vadaptor stats if firmware mode is not set to
full-featured.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The fixed link values parsed from the device tree are stored in
the struct fixed_phy member status. The struct phy_device members
speed, duplex were not updated.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a member (cpu_pwr_sample_ratio) of fam15h_power_data,
that represents the ratio of compute unit power accumulator sample
period to the PTSC counter period.
Tsample: compute unit power accumulator sample period
Tref: the performance timestamp counter period
PTSC: performance timestamp counter
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
On Carrizo and later platforms, running_avg_capture bit field is
extended to 4:31 (28 bits) from 4:25.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
We rename fam15h_power_is_internal_node0() function to
should_load_on_this_node(), because it may not be node0 from KV and
on, and they are single-node processors.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
AMD Carrizo(Fam15h, M60h) processors can report power1_crit
(ProcessorPwrWatts) and power1_input (CurrPwrWatts) values.
And this patch adds support for CZ.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Current critical clock list for pistachio enables
only mips and sys clocks by default but there are
also other clocks that are not claimed by anyone and
needs to be enabled by default.
This patch updates the critical clocks that need
to be enabled by default.
Add a separate struct to distinguish the critical clocks
as listed:
1.) core clocks:
a.) mips clock
2.) peripheral system clocks:
a.) sys clock
b.) sys_bus clock
c.) DDR clock
d.) ROM clock
Fixes: b35d7c33419c("CLK: Pistachio: Register core clocks")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
.recalc_rate callback for the fractional PLL doesn't take operating
mode into account when calculating PLL rate. This results in
the incorrect PLL rates when PLL is operating in integer mode.
Operating mode of fractional PLL is based on the value of the
fractional divider. Currently it assumes that the PLL will always
be configured in fractional mode which may not be
the case. This may result in the wrong output frequency.
Also vco was calculated based on the current operating mode which
makes no sense because .set_rate is setting operating mode. Instead,
vco should be calculated using PLL settings that are about to be set.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
PLL enable callbacks are overriding PLL mode (int/frac) and
Noise reduction (on/off) settings set by the boot loader which
results in the incorrect clock rate.
PLL mode and noise reduction are defined by the DSMPD and DACPD bits
of the PLL control register. PLL .enable() callbacks enable PLL
by deasserting all power-down bits of the PLL control register,
including DSMPD and DACPD bits, which is not necessary since
these bits don't actually enable/disable PLL.
This commit fixes the problem by removing DSMPD and DACPD bits
from the "PLL enable" mask.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresitcker <abrestic@chromium.org>
Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
This commit fixes 32bit integer overflows throughout the pll driver
(i.e. wherever the result of integer multiplication may exceed the
range of u32).
One of the functions affected by this problem is .recalc_rate. It
returns incorrect rate for some pll settings (not for all though)
which in turn results in the incorrect rate setup of pll's child
clocks.
Fixes: 43049b0c83f17("CLK: Pistachio: Add PLL driver")
Cc: <stable@vger.kernel.org> # 4.1
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Zdenko Pulitika <zdenko.pulitika@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Pull block fixes from Jens Axboe:
"Two fixes in this pull request:
- The writeback regression fix from Tejun, which has been weeks in
the making. This fixes a case where we would sometimes not issue
writeback when we should have.
- An older fix for a memory corruption issue in mtip32xx. It was
deferred since we wanted a better fix for this (driver should not
have to handle that case), but given the timing, it's better to put
the simple fix in for 4.2 release"
* 'for-linus' of git://git.kernel.dk/linux-block:
mtip32x: fix regression introduced by blk-mq per-hctx flush
writeback: sync_inodes_sb() must write out I_DIRTY_TIME inodes and always call wait_sb_inodes()
|
|
This allows drivers for devices connected via SPI to check if the
controller supports a given bits_per_word value during setup.
Currently any BPW value is accepted durings setup, and transfers
are rejected later.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Crucial M500 is known to have issues with queued TRIM commands, the
factory recertified SSDs use a different model number naming convention
which causes them to get ignored by the blacklist.
The new naming convention boils down to: s/Crucial_/FC/
Signed-off-by: Guillermo A. Amaral <g@maral.me>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
Implement magic sysrequest handling for the VT220 terminal (also known as
the Integrated ASCII console on the HMC/SE).
To invoke a "magic sysrequest" function, press "Ctrl+o" followed by a
second character that designates the debugging function.
The handling of the sysrq is scheduled away from the SCLP IRQ context;
because large amounts of sysrq output might fill up the console buffers.
The console might deadlock because it cannot empty the buffers while still
in the receiving IRQ context. This behavior is the same as for the SCLP
console.
Reported-by: Horst Weber <hweber@de.ibm.com>
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Extract the sysrq handling from the ctrlchar_handle() into a separate
function that can be directly used by other users.
Introduce a new sysrq_work structure to embed the work_struct and to
specify the magic sysrq function to be invoked.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
If a 3270 terminal is disconnected and later reconnected again,
it gets an unsolicited device end. This is currently ignored and
you have to hit the clear key to get the screen redrawn.
Add an automatic full redraw of the screen for this case.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Commit 1851617cd2da ("PCI/MSI: Disable MSI at enumeration even if kernel
doesn't support MSI") changed the location of the code that initialises
dev->msi_cap/msix_cap and then disables MSI/MSI-X interrupts at PCI
probe time in devices that have this flag set. It moved the code from
pci_msi_init_pci_dev() to a new function named pci_msi_setup_pci_dev(),
called by pci_setup_device().
The pseries PCI probing code does not call pci_setup_device(), so since
the aforementioned commit the function pci_msi_setup_pci_dev() is not
called and MSI/MSI-X interrupts are left enabled. Additionally because
dev->msi_cap/msix_cap are not initialised no driver can ever enable
MSI/MSI-X.
To fix this, the pseries PCI probe should manually call
pci_msi_setup_pci_dev(), so this patch makes it non-static.
Fixes: 1851617cd2da ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
[mpe: Update change log to mention dev->msi_cap/msix_cap]
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
It is needed to check EVENT_NO_RUNTIME_PM bit of dev->flags in
usbnet_stop(), but its value should be read before it is cleared
when dev->flags is set to 0.
The problem was spotted and the fix was provided by
Oliver Neukum <oneukum@suse.de>.
Signed-off-by: Eugene Shatokhin <eugene.shatokhin@rosalab.ru>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull nvdimm fix from Dan Williams:
"A single fix for status register read size in the nd_blk driver.
The effect of getting the width of this register read wrong is that
all I/O fails when the read returns non-zero. Given the availability
of ACPI 6 NFIT enabled platforms, this could reasonably wait to come
in during the 4.3 merge window with a tag for 4.2-stable. Otherwise,
this makes the 4.2 kernel fully functional with devices that conform
to the mmio-block-apertures defined in the ACPI 6 NFIT (NVDIMM
Firmware Interface Table)"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit, nd_blk: BLK status register is only 32 bits
|
|
[ 1065.801569] Internal error: Oops: 96000006 [#1] SMP
...
[ 1065.866655] Hardware name: AppliedMicro Mustang/Mustang, BIOS 1.1.0 Apr 22 2015
[ 1065.873937] Workqueue: events_power_efficient phy_state_machine
[ 1065.879837] task: fffffe01de105e80 ti: fffffe00bcf18000 task.ti: fffffe00bcf18000
[ 1065.887288] PC is at linkwatch_fire_event+0xac/0xc0
[ 1065.892141] LR is at linkwatch_fire_event+0xa0/0xc0
[ 1065.896995] pc : [<fffffe000060284c>] lr : [<fffffe0000602840>] pstate: 200001c5
[ 1065.904356] sp : fffffe00bcf1bd00
...
[ 1066.196813] Call Trace:
[ 1066.199248] [<fffffe000060284c>] linkwatch_fire_event+0xac/0xc0
[ 1066.205140] [<fffffe000061167c>] netif_carrier_off+0x54/0x64
[ 1066.210773] [<fffffe00004f1654>] phy_state_machine+0x120/0x3bc
[ 1066.216578] [<fffffe00000d8d10>] process_one_work+0x15c/0x3a8
[ 1066.222296] [<fffffe00000d9090>] worker_thread+0x134/0x470
[ 1066.227757] [<fffffe00000df014>] kthread+0xe0/0xf8
[ 1066.232525] Code: 97f65ee9 f9420660 d538d082 8b000042 (885f7c40)
The fix is to call phy_disconnect() from xgene_enet_mdio_remove,
which in turn call cancel_delayed_work_sync().
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only read 32 bits for the BLK status register in read_blk_stat().
The format and size of this register is defined in the
"NVDIMM Driver Writer's guide":
http://pmem.io/documents/NVDIMM_Driver_Writers_Guide.pdf
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reported-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Tested-by: Nicholas Moulin <nicholas.w.moulin@linux.intel.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Rather than re-initialising the entire completion on every mdio access,
use reinit_completion() which only resets the completion count. This
avoids possible reinitialisation of the contained spinlock and waitqueue
while they may be in use (eg, mid-completion.)
Such an event could occur if there's a long delay in interrupt handling
causing the mdio accessor to time out, then a second access comes in
while the interrupt handler on a different CPU has called complete().
Another scenario where this has been observed is while locking has
been missing at the phy layer, allowing concurrent attempts to access
the MDIO bus.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phy layer is missing locking for the above two functions - it
has been observed that two threads (userspace and the phy worker
thread) can race, entering the bus ->write or ->read functions
simultaneously.
This causes the FEC driver to initialise a completion while another
thread is waiting on it or while the interrupt is calling complete()
on it, which causes spinlock unlock-without-lock, spinlock lockups,
and completion timeouts.
Fixes: a59a4d192 ("phy: add the EEE support and the way to access to the MMD registers.")
Fixes: 0c1d77dfb ("net: libphy: Add phy specific function to access mmd phy registers")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before 56ef9c909b40[1] it used to ignore all errors from igmp_join().
That commit enhanced that and made it error out whatever error happened
with igmp_join(), but that's not good because when using multicast
groups vxlan will try to join it multiple times if the socket is reused
and then the 2nd and further attempts will fail with EADDRINUSE.
As we don't track to which groups the socket is already subscribed, it's
okay to just ignore that error.
Fixes: 56ef9c909b40 ("vxlan: Move socket initialization to within rtnl scope")
Reported-by: John Nielsen <lists@jnielsen.net>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
this is the updated pull request of one patch by me for the peak_usb
driver. It fixes the driver, so that non FD adapters don't provide CAN
FD bittimings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the renesas ethernet driver directory is compiled if SH_ETH is
configured rather than NET_VENDOR_RENESAS. Although incorrect that was
quite harmless as until recently as SH_ETH configured the only driver in
the renesas directory. However, as of c156633f1353 ("Renesas Ethernet AVB
driver proper") the renesas directory includes another driver, configured
by RAVB, and it makes little sense for it to have a hidden dependency on
SH_ETH.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[horms: rewrote changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The latest Tegra clk pull had some problems. Fix them.
drivers/clk/tegra/clk-tegra124.c:1450:6: warning: symbol 'tegra124_clock_assert_dfll_dvco_reset' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra124.c:1466:6: warning: symbol 'tegra124_clock_deassert_dfll_dvco_reset' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra124.c:1476:5: warning: symbol 'tegra124_reset_assert' was not declared. Should it be static?
drivers/clk/tegra/clk-tegra124.c:1486:5: warning: symbol 'tegra124_reset_deassert' was not declared. Should it be static?
drivers/clk/tegra/clk-dfll.c:590 dfll_load_i2c_lut() warn: inconsistent indenting
drivers/clk/tegra/clk-dfll.c:1448 dfll_build_i2c_lut() warn: unsigned 'td->i2c_lut[0]' is never less than zero.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.3-rc1
This contains the DFLL driver needed to implement CPU frequency scaling
on Tegra.
|
|
Hi,
After commit f70ced091707 (blk-mq: support per-distpatch_queue flush
machinery), the mtip32xx driver may oops upon module load due to walking
off the end of an array in mtip_init_cmd. On initialization of the
flush_rq, init_request is called with request_index >= the maximum queue
depth the driver supports. For mtip32xx, this value is used to index
into an array. What this means is that the driver will walk off the end
of the array, and either oops or cause random memory corruption.
The problem is easily reproduced by doing modprobe/rmmod of the mtip32xx
driver in a loop. I can typically reproduce the problem in about 30
seconds.
Now, in the case of mtip32xx, it actually doesn't support flush/fua, so
I think we can simply return without doing anything. In addition, no
other mq-enabled driver does anything with the request_index passed into
init_request(), so no other driver is affected. However, I'm not really
sure what is expected of drivers. Ming, what did you envision drivers
would do when initializing the flush requests?
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
If memory allocation gets failed on parsing the DT, then it returns error
'-ENOMEM' explicitly. Then, the driver exists from the _probe().
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
platform data
Currently, lp872x driver parses the DT and copies values into the
'cl->dev.platform_data' if 'of_node' exists.
This may have architectural issue. Platform data is configurable through
the DT or I2C board info inside the platform area.
However, lp872x driver changes this configuration when it is loaded.
The lp872x driver should get data from the platform side and use the private
data, 'lp872x->pdata' instead of changing the original platform data.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
