Age | Commit message (Collapse) | Author |
|
userspace can ask to perform various smart config
actions via custom vendor commands.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
These commands configures the fw to set key,
enter smart config mode, and exit it.
Add relevant hw ops as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add definitions for the smart config commands.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The LAA bit is second bit of the MSB, not of the
third byte.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The last tx rate calculation didn't take into account
the different indices of 11a and 11g rates tables.
Add the required alignment (count only from the first
11a rate in case of 11a)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
On recovery, we increase the current seq num by
WL1271_TX_SQN_POST_RECOVERY_PADDING in order to
compensate for packets we might have missed during
recovery.
It seems that some GEM APs have issues when the
gap is too big, so use a smaller padding in this case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We want seq num (freed_pkts) to be initialized
on each new connection, but keep persistent
between recoveries/suspends.
Save the freed_pkts in the private block of the
sta struct (we already do a similar thing for
AP's stations).
However, keep the old wlvif->total_freed_pkts
in order to avoid too intrusive change.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This could be a bit confusing to see warning about lacking support for
5 GHz band if your device supports 2.4 GHz only.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Support for N-PHY rev 8 with 0x2057 rev 5 is almost ready, but we still
need to figure out how to handle rev 9 first.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Initialization of N-PHY radio revs 5 and 7 requires writing to 0x1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Type of radio has a major meaning for the driver. There is quite some
code that does initialization/calibration depending on the radio rev.
Knowing radio params is quite important to provide help to users, so
print it even with debugging disabled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
Add support for the QCA6174 chip.
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 30 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3432 Rev=00.02
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: Anantha Krishnan <ananthk@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
New Broadcom PCIe devices (802.11ac ones?) use Gen2 and have to be
initialized differently.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This changes
b43-phy0: Found Radio: Manuf 0x17F, Version 0x7769, Revision 4
to the
b43-phy0: Found Radio: Manuf 0x17F, Version 0x2069, Revision 4
which matches what closed source driver reports:
$ wl revinfo
radiorev 0x42069000
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This allows adding more revisions support, spotting lacking tables and
unifies naming schema.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Function rt2800usb_autorun_detect() passes the address of a variable
allocated onto the stack to be used for DMA by the USB layer. This has
been caught by my debugging-enabled kernel.
This patch change things in order to allocate that variable via
kmalloc, and it adjusts things to handle the kmalloc failure case,
propagating the error.
[ 7363.238852] ------------[ cut here ]------------
[ 7363.243529] WARNING: CPU: 1 PID: 5235 at lib/dma-debug.c:1153 check_for_stack+0xa4/0xf0()
[ 7363.251759] ehci-pci 0000:00:04.1: DMA-API: device driver maps memory fromstack [addr=ffff88006b81bad4]
[ 7363.261210] Modules linked in: rt2800usb(O+) rt2800lib(O) rt2x00usb(O) rt2x00lib(O) rtl818x_pci(O) rtl8187 led_class eeprom_93cx6 mac80211 cfg80211 [last unloaded: rt2x00lib]
[ 7363.277143] CPU: 1 PID: 5235 Comm: systemd-udevd Tainted: G O 3.16.0-rc3-wl+ #31
[ 7363.285546] Hardware name: System manufacturer System Product Name/M3N78 PRO, BIOS ASUS M3N78 PRO ACPI BIOS Revision 1402 12/04/2009
[ 7363.297511] 0000000000000009 ffff88006b81b710 ffffffff8175dcad ffff88006b81b758
[ 7363.305062] ffff88006b81b748 ffffffff8106d372 ffff88006cf10098 ffff88006cead6a0
[ 7363.312622] ffff88006b81bad4 ffffffff81c1e7c0 ffff88006cf10098 ffff88006b81b7a8
[ 7363.320161] Call Trace:
[ 7363.322661] [<ffffffff8175dcad>] dump_stack+0x4d/0x6f
[ 7363.327847] [<ffffffff8106d372>] warn_slowpath_common+0x82/0xb0
[ 7363.333893] [<ffffffff8106d3e7>] warn_slowpath_fmt+0x47/0x50
[ 7363.339686] [<ffffffff813a93b4>] check_for_stack+0xa4/0xf0
[ 7363.345298] [<ffffffff813a995c>] debug_dma_map_page+0x10c/0x150
[ 7363.351367] [<ffffffff81521bd9>] usb_hcd_map_urb_for_dma+0x229/0x720
[ 7363.357890] [<ffffffff8152256d>] usb_hcd_submit_urb+0x2fd/0x930
[ 7363.363929] [<ffffffff810eac31>] ? irq_work_queue+0x71/0xd0
[ 7363.369617] [<ffffffff810ab5a7>] ? wake_up_klogd+0x37/0x50
[ 7363.375219] [<ffffffff810ab7a5>] ? console_unlock+0x1e5/0x420
[ 7363.381081] [<ffffffff810abc25>] ? vprintk_emit+0x245/0x530
[ 7363.386773] [<ffffffff81523d3c>] usb_submit_urb+0x30c/0x580
[ 7363.392462] [<ffffffff81524295>] usb_start_wait_urb+0x65/0xf0
[ 7363.398325] [<ffffffff815243ed>] usb_control_msg+0xcd/0x110
[ 7363.404014] [<ffffffffa005514d>] rt2x00usb_vendor_request+0xbd/0x170 [rt2x00usb]
[ 7363.411544] [<ffffffffa0074292>] rt2800usb_autorun_detect+0x32/0x50 [rt2800usb]
[ 7363.418986] [<ffffffffa0074aa1>] rt2800usb_read_eeprom+0x11/0x70 [rt2800usb]
[ 7363.426168] [<ffffffffa0063ffd>] rt2800_probe_hw+0x11d/0xf90 [rt2800lib]
[ 7363.432989] [<ffffffffa0074b7d>] rt2800usb_probe_hw+0xd/0x50 [rt2800usb]
[ 7363.439808] [<ffffffffa00453d8>] rt2x00lib_probe_dev+0x238/0x7c0 [rt2x00lib]
[ 7363.446992] [<ffffffffa00bfa48>] ? ieee80211_led_names+0xb8/0x100 [mac80211]
[ 7363.454156] [<ffffffffa0056116>] rt2x00usb_probe+0x156/0x1f0 [rt2x00usb]
[ 7363.460971] [<ffffffffa0074250>] rt2800usb_probe+0x10/0x20 [rt2800usb]
[ 7363.467616] [<ffffffff8152799e>] usb_probe_interface+0xce/0x1c0
[ 7363.473651] [<ffffffff81480c20>] really_probe+0x70/0x240
[ 7363.479079] [<ffffffff81480f01>] __driver_attach+0xa1/0xb0
[ 7363.484682] [<ffffffff81480e60>] ? __device_attach+0x70/0x70
[ 7363.490461] [<ffffffff8147eef3>] bus_for_each_dev+0x63/0xa0
[ 7363.496146] [<ffffffff814807c9>] driver_attach+0x19/0x20
[ 7363.501570] [<ffffffff81480468>] bus_add_driver+0x178/0x220
[ 7363.507270] [<ffffffff8148151b>] driver_register+0x5b/0xe0
[ 7363.512874] [<ffffffff815271b0>] usb_register_driver+0xa0/0x170
[ 7363.518905] [<ffffffffa007a000>] ? 0xffffffffa0079fff
[ 7363.524074] [<ffffffffa007a01e>] rt2800usb_driver_init+0x1e/0x20 [rt2800usb]
[ 7363.531247] [<ffffffff810002d4>] do_one_initcall+0x84/0x1b0
[ 7363.536932] [<ffffffff8113aa60>] ? kfree+0xd0/0x110
[ 7363.541931] [<ffffffff8112730a>] ? __vunmap+0xaa/0xf0
[ 7363.547538] [<ffffffff810ca07e>] load_module+0x1aee/0x2040
[ 7363.553141] [<ffffffff810c6f10>] ? store_uevent+0x50/0x50
[ 7363.558676] [<ffffffff810ca66e>] SyS_init_module+0x9e/0xc0
[ 7363.564285] [<ffffffff81764012>] system_call_fastpath+0x16/0x1b
[ 7363.570338] ---[ end trace 01ef5f822bea9882 ]---
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
|
|
The comment was not accurate, we are talking about the frames
*for* the station and not from the station.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
This patch removes the setting of the ADC sampling bits in
the mvm nic configuration. This setting is not required by
the firmware, and furthermore - it interferes with the DBGC
when it is running in DRAM mode on PCIe.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The FW currently doesn't optimally support TDLS in DCM mode. Teardown
all TDLS peers when we have more than a single phy context.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The FW does not support PSM on a vif with associated TDLS peers. Disable
PSM when the first peer joins and re-enable it when the last leaves.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Use the new mac80211 callback to protect a TDLS discovery session so we
can hear the discovery-response packet.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
HW/FW constraints dictate that TDLS should only be used when a single
phy ctx is active. We also support at most 4 TDLS peers. We don't
support TDLS on a P2P vif.
Unify and move a phy-ctx counting implementation from the power-mgmt code
in order to simplify implementation.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
An AP/GO may perform the channel switch slightly before its stations.
This scenario may result in packet loss, since the transmission may start
before the client is actually on a new channel. In order to prevent
potential packet loss disable tx to all the stations when the channel
switch flow starts. Clear the disable_tx bit when a station is seen on a
target channel, or after IWL_MVM_CS_UNBLOCK_TX_TIMEOUT beacons on a new
channel. In addition call ieee80211_sta_block_awake in order to inform
mac80211 that the frames for this station should be buffered.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
According to the spec, GO/AP should perform the channel switch just
before "beacon 0". However, since the exact timing isn't defined,
it may result in a sudden GO disappearance from the channel.
Prevent potential packet loss when performing the CS by scheduling
NoA time event and executing the channel switch flow when a notification
from fw is received.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Currently mvm->csa_vif is protected with mvm mutex. The RCU protection
is required for "iwlwifi: mvm: Reflect GO channel switch in NoA" patch.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Call ieee80211_beacon_get_template instead of ieee80211_beacon_get and sync the
CSA counters with mac80211 after each beacon transmission.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Implement support for unbind-bind flow for the client roles. This
includes telling the firmware that we are not associated, removing
time-events, removing quotas and updating power management during the
actual switch, and redoing everything in the new channel.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Implement the switch_vif_chanctx operation with support for a
single-vif and SWAP mode. The REASSIGN mode and multi-vifs are not
supported yet.
This operation needs to implement 4 steps, namely unassign, remove,
add and assign the chanctx. In order to do this, split out these
operations into locked and non-locked parts, thus allowing us to call
them while locked.
Additionally, in order to allow us to restart the hardware when
something fails, add a boolean to the iwl_mvm_nic_restart() function
that tells whether the restart was triggered by a FW error or
something else.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
It turns out that adding the update type argument was pointless as
quota update is never called from the add_interface() callback.
Therefore, IWL_MVM_QUOTA_UPDATE_TYPE_NEW isn't actually needed and
then only a "disabled_vif" argument is needed for the upcoming CSA
work.
Remove the whole enum iwl_mvm_quota_update_type and pass the right
arguments (always NULL for disabled vif right now) to the function
in all current call sites.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Simplify the quota iterator by not passing the update type,
it only needs to know whether or not to skip an interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
The firmware currently deals with zero quota for a given
binding, but it seems odd to send that down. Make sure
that we don't do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
There are some cases where we can currently send zero quota
for a valid binding, e.g. if we update while an interface is
bound to a channel context but not yet acting as an AP.
Avoid this by reordering the checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
In some cases (e.g. when we're doing a channel switch), we may need to
disable the quota of a vif temporarily. In order to do so, add an
argument to the iwl_mvm_update_quotas() function to tell if the passed
vif is a new one or if it should be disregarded.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
when driver takes the MAC address from the HW section and
it isn't valid - print an error.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Initialize LMAC scan command.
Fix EBS flag to be dependant on TLV flg and fix other bugs.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Add new scan API that uses the same command 0x51 for both regular and
sched scan.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
These file are removed recursively anyway, so there's no
point saving them just to redundantly remove them later.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
iwl_mvm_rs_rate_init() is called multiple times to re-init
the rate scaling statistics (e.g. after some idle time).
It clears all the lq_sta sta, including some fields that
shouldn't be cleared (e.g. debugfs pointers). Fix it
by adding a new 'persistent' sub-struct, and
avoid clearing it on (re-)init.
Move the initialization of the persistent fields to
rs_alloc_sta instead.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|
|
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
|