| Age | Commit message (Collapse) | Author |
|---|
|
Ethtool callbacks {get|set}_link_ksettings are often the same, so
we add two generics functions phy_ethtool_{get|set}_link_ksettings
to avoid writing severals times the same function.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-By: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2016-05-09
this is a pull request of 12 patches for net-next/master.
Alexander Gerasiov and Nikita Edward Baruzdin each contribute a patch
improving the sja1000 driver. Amitoj Kaur Chawla's patch converts the
mcp251x driver to alloc_workqueue(). A patch by Oliver Hartkopp fixes
the handling of CAN config options. Andreas Gröger improves the error
handling in the janz-ican3 driver. The patch by Maximilian Schneider
for the gs_usb improves probing of the USB driver. Finally there are 6
improvement patches by Marek Vasut for the ifi CAN driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is an initial implementation of a netdev driver for GTP datapath
(GTP-U) v0 and v1, according to the GSM TS 09.60 and 3GPP TS 29.060
standards. This tunneling protocol is used to prevent subscribers from
accessing mobile carrier core network infrastructure.
This implementation requires a GGSN userspace daemon that implements the
signaling protocol (GTP-C), such as OpenGGSN [1]. This userspace daemon
updates the PDP context database that represents active subscriber
sessions through a genetlink interface.
For more context on this tunneling protocol, you can check the slides
that were presented during the NetDev 1.1 [2].
Only IPv4 is supported at this time.
[1] http://git.osmocom.org/openggsn/
[2] http://www.netdevconf.org/1.1/proceedings/slides/schultz-welte-osmocom-gtp.pdf
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the following sparse warning:
drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c:274:1: warning:
symbol 'socfpga_dwmac_pm_ops' was not declared. Should it be static?
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow udp and raw sockets to send by oif that is an enslaved interface
versus the l3mdev/VRF device. For example, this allows BFD to use ifindex
from IP_PKTINFO on a receive to send a response without the need to
convert to the VRF index. It also allows ping and ping6 to work when
specifying an enslaved interface (e.g., ping -I swp1 <ip>) which is
a natural use case.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit-bd5a256 introduces a deadlock bug in fjes_change_mtu().
This spin_lock_irqsave() is obviously unnecessary.
This patch eliminates unnecessary spin_lock_irqsave() in
fjes_change_mtu()
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I accidently let Arnd's VXLAN dependency changes slip into net-next,
they are only appropriate for net.
Also the flow steering structural changes to mlx5e_priv got scrambled
during the merge resolution as well.
Fix that all up.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes the following issues:
- bug in ahash SG list walking that may lead to crashes
- resource leak in qat
- missing RSA dependency that causes it to fail"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: rsa - select crypto mgr dependency
crypto: hash - Fix page length clamping in hash walk
crypto: qat - fix adf_ctl_drv.c:undefined reference to adf_init_pf_wq
crypto: qat - fix invalid pf2vf_resp_wq logic
|
|
Pull networking fixes from David Miller:
1) Check klogctl failure correctly, from Colin Ian King.
2) Prevent OOM when under memory pressure in flowcache, from Steffen
Klassert.
3) Fix info leak in llc and rtnetlink ifmap code, from Kangjie Lu.
4) Memory barrier and multicast handling fixes in bnxt_en, from Michael
Chan.
5) Endianness bug in mlx5, from Daniel Jurgens.
6) Fix disconnect handling in VSOCK, from Ian Campbell.
7) Fix locking of netdev list walking in get_bridge_ifindices(), from
Nikolay Aleksandrov.
8) Bridge multicast MLD parser can look at wrong packet offsets, fix
from Linus Lüssing.
9) Fix chip hang in qede driver, from Sudarsana Reddy Kalluru.
10) Fix missing setting of encapsulation before inner handling completes
in udp_offload code, from Jarno Rajahalme.
11) Missing rollbacks during LAG join and flood configuration failures
in mlxsw driver, from Ido Schimmel.
12) Fix error code checks in netxen driver, from Dan Carpenter.
13) Fix key size in new macsec driver, from Sabrina Dubroca.
14) Fix mlx5/VXLAN dependencies, from Arnd Bergmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
net/mlx5e: make VXLAN support conditional
Revert "net/mlx5: Kconfig: Fix MLX5_EN/VXLAN build issue"
macsec: key identifier is 128 bits, not 64
Documentation/networking: more accurate LCO explanation
macvtap: segmented packet is consumed
tools: bpf_jit_disasm: check for klogctl failure
qede: uninitialized variable in qede_start_xmit()
netxen: netxen_rom_fast_read() doesn't return -1
netxen: reversed condition in netxen_nic_set_link_parameters()
netxen: fix error handling in netxen_get_flash_block()
mlxsw: spectrum: Add missing rollback in flood configuration
mlxsw: spectrum: Fix rollback order in LAG join failure
udp_offload: Set encapsulation before inner completes.
udp_tunnel: Remove redundant udp_tunnel_gro_complete().
qede: prevent chip hang when increasing channels
net: ipv6: tcp reset, icmp need to consider L3 domain
bridge: fix igmp / mld query parsing
net: bridge: fix old ioctl unlocked net device walk
VSOCK: do not disconnect socket when peer has shutdown SEND only
net/mlx4_en: Fix endianness bug in IPV6 csum calculation
...
|
|
Now that all drivers support the same set of functions and the same
setup code, drop every model-specific DSA switch driver and replace them
with a common mv88e6xxx driver.
This merges the info tables into one, removes the function exports, the
model-specific files, and update the defconfigs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
6131 is the only driver to set the tag protocol to DSA_TAG_PROTO_DSA.
Since it works fine with DSA_TAG_PROTO_EDSA, change its value, like all
other mv88e6xxx drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Provide a shared mv88e6xxx_setup function to the drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
6131 is the only driver which setups the priority of IGMP/MLD snoop
frames and ARP frames to the highest setting. Drop such change until we
figure out a common configuration for all switch models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All switch models setup the GLOBAL_CONTROL_2 register with slightly
differences.
Since the cascade mode is valid even in a single chip setup, factorize
such configuration.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All switch drivers configure the GLOBAL_MONITOR_CONTROL register with
slightly changes.
Assume the setup of the upstream port, and configure it as the port to
which ingress and egress and ARP monitor frames are to be sent.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 6131 switch models have a Core Tag Type register. Their setup code
is setting it to 0x8100, which is the reset default.
Drop this specific part which is correctly configured on reset anyway.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All switch models configure the GLOBAL_CONTROL register with slightly
differences.
Discarding packets with excessive collisions
(GLOBAL_CONTROL_DISCARD_EXCESS) is specific to 6352 and similar
switches, and setting a maximum frame size
(GLOBAL_CONTROL_MAX_FRAME_1632) is specific to 6185 and similar
switches.
As we are centralizing the chips setup, skip these settings and don't
discard any frames yet, until we found out that such discarding by the
hardware is necessary.
Assume a common setup to enable the PHY Polling Unit if present, don't
discard any packets, and mask all interrupt sources.
Tested on 88E6352 and 88E6185.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every driver is calling mv88e6xxx_setup_global after
mv88e6xxx_setup_common. Call the former in the latter.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_PPU_ACTIVE flag to describe how to reset the
switch, and merge the reset call to the common setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_ATU flag to identify switch models with an Address
Translation Unit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_VTU flag to indentify switch models with a VLAN
Table Unit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add MV88E6XXX_FLAG_PORTSTATE and MV88E6XXX_FLAG_VLANTABLE flags to
identify switch models with required 802.1D operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only 6131 was not supporting the port registers access yet. Assume such
support and use the unlock access routines in the meantime.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_EEE flag to describe switch models featuring Energy
Efficient Ethernet. Use it to conditionally support such access in the
common code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some switch models have a dedicated register for Switch MAC/WoF/WoL.
This register, when present, is used to indirectly set the switch MAC
address, instead of a direct write to 3 global registers.
Identify this feature and share a common mv88e6xxx_set_addr function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add MV88E6XXX_FLAG_TEMP and MV88E6XXX_FLAG_TEMP_LIMIT flags to describe
switch models featuring a temperature access. Use them to centralize the
access to the temperature feature.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_EEPROM flag to describe switch models featuring an
EEPROM and distribute the EEPROM access routines to all models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some switch has dedicated SMI PHY Command and Data registers, used to
indirectly access the PHYs, instead of direct access.
Identify these switch models and make mv88e6xxx_phy_{read,write} generic
enough to support every models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_PPU flag to describe switch models with a PHY
Polling Unit. This allows to merge PPU specific PHY access code in the
share code.
Make the mv88e6xxx_ppu_disable and mv88e6xxx_phy_{read,write}_ppu
functions use unlocked register accesses in order to call them in
mv88e6xxx_phy_{read,write} in a locked context.
Since the PPU code is shared, also remove NET_DSA_MV88E6XXX_NEED_PPU.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a flags bitmap to the info structure in order to identify features
supported or not by the different switch models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The updated specification for the IFI CANFD core contains description
of more detailed error reporting capability of the core. Implement
support for this detailed error reporting.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Only increment the TX counters in the irq handler if a CAN message
was sent. The current code incremented the counters also if the TX
FIFO empty interrupt happened, which is incorrect.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The CAN_CTRLMODE_FD flag is set for both ISO and BOSCH CANFD mode,
while the CAN_CTRLMODE_FD_NON_ISO is additional flag which is only
set for CANFD-BOSCH mode. Fix the handling of the flags to reflect
this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
There is no distinction between bittiming constants for the slow and
fast part of the CANFD operation on this controller, so just use one
single bittiming constant set.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The updated documentation regarding the IFI CANFD core from April 2016
adds more details regarding the timing calculation. There is no longer
any distinction in the timing calculation between CANFD and CAN2.0, but
instead there are two timing modes -- 4_12_6_6 and 7_9_8_8 -- where the
numbers mean the width in bits of the SJW/Prescaler/TimeA/TimeB fields.
The code uses 7_9_8_8 mode, which allows more fine-grained control over
the timing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Start the NAPI polling in case the bus warning interrupt happens,
since it is the poll function which checks and reports the warning.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Modified the USB device table to use only the first USB interface, as is
the case with GS USB devices. This allows other GS USB compatible
devices to be more flexible with their remaining interfaces.
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
My patch of May 2015 was missing the changed handling of error
indications. With CAL/CANopen firmware the NMTS-SlaveEventIndication
must be used instead of CAN-EventIndication. An appropriate slave node
must be configured to report the errors.
In our department (about 15 development systems with Janz ICAN3-
modules with firmware 1.48, my system also with firmware ICANOS 1.35)
we use the driver with this patch for about one year: no known problems.
Signed-off-by: Andreas Gröger <andreas24groeger@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
As described in 'can: m_can: tag current CAN FD controllers as non-ISO'
(6cfda7fbebe) it is possible to define fixed configuration options by
setting the according bit in 'ctrlmode' and clear it in 'ctrlmode_supported'.
This leads to the incovenience that the fixed configuration bits can not be
passed by netlink even when they have the correct values (e.g. non-ISO, FD).
This patch fixes that issue and not only allows fixed set bit values to be set
again but now requires(!) to provide these fixed values at configuration time.
A valid CAN FD configuration consists of a nominal/arbitration bittiming, a
data bittiming and a control mode with CAN_CTRLMODE_FD set - which is now
enforced by a new can_validate() function. This fix additionally removed the
inconsistency that was prohibiting the support of 'CANFD-only' controller
drivers, like the RCar CAN FD.
For this reason a new helper can_set_static_ctrlmode() has been introduced to
provide a proper interface to handle static enabled CAN controller options.
Reported-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Reviewed-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Cc: <stable@vger.kernel.org> # >= 3.18
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Replace scheduled to be removed create_freezable_workqueue with
alloc_workqueue.
priv->wq should be explicitly set as freezable to ensure it is frozen
in the suspend sequence and work items are drained so that no new work
item starts execution until thawed. Thus, use of WQ_FREEZABLE flag
here is required.
WQ_MEM_RECLAIM flag has been set here to ensure forward progress
regardless of memory pressure.
The order of execution is not important so set @max_active as 0.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds support for the Marathon CAN-bus-PCIe card to the
sja1000 driver. For more information see:
http://can.marathon.ru/page/devices/can-bus-pcie
Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
According to SJA1000 documentation the location of error is available
regardless of an error type. Therefore it should always be forwarded to
SocketCAN.
Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@lvk.cs.msu.su>
Signed-off-by: Alexander GQ Gerasiov <gq@cs.msu.su>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
VXLAN can be disabled at compile-time or it can be a loadable
module while mlx5 is built-in, which leads to a link error:
drivers/net/built-in.o: In function `mlx5e_create_netdev':
ntb_netdev.c:(.text+0x106de4): undefined reference to `vxlan_get_rx_port'
This avoids the link error and makes the vxlan code optional,
like the other ethernet drivers do as well.
Link: https://patchwork.ozlabs.org/patch/589296/
Fixes: b3f63c3d5e2c ("net/mlx5e: Add netdev support for VXLAN tunneling")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 69976fb1045850a742deb9790ea49cbc6f497531.
We cannot select VXLAN when IPv4 support is disabled, that just gives
us additional build errors, including:
warning: (MLX5_CORE_EN) selects VXLAN which has unmet direct dependencies (NETDEVICES && NET_CORE && INET)
In file included from ../drivers/net/vxlan.c:36:0:
include/net/udp_tunnel.h: In function 'udp_tunnel_handle_offloads':
include/net/udp_tunnel.h:112:9: error: implicit declaration of function 'iptunnel_handle_offloads' [-Werror=implicit-function-declaration]
return iptunnel_handle_offloads(skb, type);
^~~~~~~~~~~~~~~~~~~~~~~~
I'm sending a proper fix for the original bug in a separate patch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All the chip_reset() methods repeat the code writing to the ARSTR register
and delaying for 1 ms, so that we can reuse sh_eth_chip_reset() twice.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sh_eth_chip_reset_giga() doesn't really need to use direct iowrite32() when
writing to the ARSTR register, it can use sh_eth_tsu_write() as all other
chip_reset() methods.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that mdiobus_scan() doesn't return NULL on failure anymore, this driver
no longer needs to check for it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-05-07
Here are a few more Bluetooth patches for the 4.7 kernel:
- NULL pointer fix in hci_intel driver
- New Intel Bluetooth controller id in btusb driver
- Added device tree binding documentation for Marvel's bt-sd8xxx
- Platform specific wakeup interrupt support for btmrvl driver
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MACsec standard mentions a key identifier for each key, but
doesn't specify anything about it, so I arbitrarily chose 64 bits.
IEEE 802.1X-2010 specifies MKA (MACsec Key Agreement), and defines the
key identifier to be 128 bits (96 bits "member identifier" + 32 bits
"key number").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
