| Age | Commit message (Collapse) | Author |
|---|
|
[ Upstream commit f2899788353c13891412b273fdff5f02d49aa40f ]
The 88m1101 has an errata when configuring autoneg. However, it was
being applied to many other Marvell PHYs as well. Limit its scope to
just the 88m1101.
Fixes: 76884679c644 ("phylib: Add support for Marvell 88e1111S and 88e1145")
Reported-by: Daniel Walker <danielwa@cisco.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 73dd3a4839c1d27c36d4dcc92e1ff44225ecbeb7 ]
Currently when firmware command gets stuck or it takes long time to
complete, the driver command will get timeout and the command slot is
freed and can be used for new commands, and if the firmware receive new
command on the old busy slot its behavior is unexpected and this could
be harmful.
To fix this when the driver command gets timeout we return failure,
but we don't free the command slot and we wait for the firmware to
explicitly respond to that command.
Once all the entries are busy we will stop processing new firmware
commands.
Fixes: 9cba4ebcf374 ('net/mlx5: Fix potential deadlock in command mode change')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 751da2a69b7cc82d83dc310ed7606225f2d6e014 ]
As of 7bb11dc9f59d and 0622cab0341c, bond slaves in a 3ad bond are not
removed from the aggregator when they are down, and the active slave count
is NOT equal to number of ports in the aggregator, but rather the number
of ports in the aggregator that are still enabled. The sysfs spew for
bonding_show_ad_num_ports() has a comment that says "Show number of active
802.3ad ports.", but it's currently showing total number of ports, both
active and inactive. Remedy it by using the same logic introduced in
0622cab0341c in __bond_3ad_get_active_agg_info(), so sysfs, procfs and
netlink all report the number of active ports. Note that this means that
IFLA_BOND_AD_INFO_NUM_PORTS really means NUM_ACTIVE_PORTS instead of
NUM_PORTS, and thus perhaps should be renamed for clarity.
Lightly tested on a dual i40e lacp bond, simulating link downs with an ip
link set dev <slave2> down, was able to produce the state where I could
see both in the same aggregator, but a number of ports count of 1.
MII Status: up
Active Aggregator Info:
Aggregator ID: 1
Number of ports: 2 <---
Slave Interface: ens10
MII Status: up <---
Aggregator ID: 1
Slave Interface: ens11
MII Status: up
Aggregator ID: 1
MII Status: up
Active Aggregator Info:
Aggregator ID: 1
Number of ports: 1 <---
Slave Interface: ens10
MII Status: down <---
Aggregator ID: 1
Slave Interface: ens11
MII Status: up
Aggregator ID: 1
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 486181bcb3248e2f1977f4e69387a898234a4e1e ]
In their infinite wisdom, and never ending quest for end user frustration,
Lenovo has decided to use a new USB device ID for the wwan modules in
their 2017 laptops. The actual hardware is still the Sierra Wireless
EM7455 or EM7430, depending on region.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e3c19503712d6360239b19c14cded56dd63c40d7 ]
Pause bit should set when RX pause is on, not TX pause.
Also, setting Asym_Pause is incorrect, and should be turned off.
Fixes: 665bc53969d7 ("net/mlx5e: Use new ethtool get/set link ksettings API")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b383b544f2666d67446b951a9a97af239dafed5d ]
Query the operational pause from firmware (PFCC register) instead of
always passing zeros.
Fixes: 665bc53969d7 ("net/mlx5e: Use new ethtool get/set link ksettings API")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ebccc7397e4a49ff64c8f44a54895de9d32fe742 ]
commit 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
added new hash tables, but missed to initialize them.
Fixes: 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 25e2c341e7818a394da9abc403716278ee646014 ]
Access card->dev only after checking whether's its valid.
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2d2ebb3ed0c6acfb014f98e427298673a5d07b82 ]
commit b4d72c08b358 ("qeth: bridgeport support - basic control")
broke the support for OSM and OSN devices as follows:
As OSM and OSN are L2 only, qeth_core_probe_device() does an early
setup by loading the l2 discipline and calling qeth_l2_probe_device().
In this context, adding the l2-specific bridgeport sysfs attributes
via qeth_l2_create_device_attributes() hits a BUG_ON in fs/sysfs/group.c,
since the basic sysfs infrastructure for the device hasn't been
established yet.
Note that OSN actually has its own unique sysfs attributes
(qeth_osn_devtype), so the additional attributes shouldn't be created
at all.
For OSM, add a new qeth_l2_devtype that contains all the common
and l2-specific sysfs attributes.
When qeth_core_probe_device() does early setup for OSM or OSN, assign
the corresponding devtype so that the ccwgroup probe code creates the
full set of sysfs attributes.
This allows us to skip qeth_l2_create_device_attributes() in case
of an early setup.
Any device that can't do early setup will initially have only the
generic sysfs attributes, and when it's probed later
qeth_l2_probe_device() adds the l2-specific attributes.
If an early-setup device is removed (by calling ccwgroup_ungroup()),
device_unregister() will - using the devtype - delete the
l2-specific attributes before qeth_l2_remove_device() is called.
So make sure to not remove them twice.
What complicates the issue is that qeth_l2_probe_device() and
qeth_l2_remove_device() is also called on a device when its
layer2 attribute changes (ie. its layer mode is switched).
For early-setup devices this wouldn't work properly - we wouldn't
remove the l2-specific attributes when switching to L3.
But switching the layer mode doesn't actually make any sense;
we already decided that the device can only operate in L2!
So just refuse to switch the layer mode on such devices. Note that
OSN doesn't have a layer2 attribute, so we only need to special-case
OSM.
Based on an initial patch by Ursula Braun.
Fixes: b4d72c08b358 ("qeth: bridgeport support - basic control")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9111e7880ccf419548c7b0887df020b08eadb075 ]
When setting up the device from within the layer discipline's
probe routine, creating the layer-specific sysfs attributes can fail.
Report this error back to the caller, and handle it by
releasing the layer discipline.
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
[jwi: updated commit msg, moved an OSN change to a subsequent patch]
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1a4a5bf52a4adb477adb075e5afce925824ad132 ]
The current codes only deal with the case that the skb is dropped, it
may meet one use-after-free issue when NF_HOOK returns 0 that means
the skb is stolen by one netfilter rule or hook.
When one netfilter rule or hook stoles the skb and return NF_STOLEN,
it means the skb is taken by the rule, and other modules should not
touch this skb ever. Maybe the skb is queued or freed directly by the
rule.
Now uses the nf_hook instead of NF_HOOK to get the result of netfilter,
and check the return value of nf_hook. Only when its value equals 1, it
means the skb could go ahead. Or reset the skb as NULL.
BTW, because vrf_rcv_finish is empty function, so needn't invoke it
even though nf_hook returns 1. But we need to modify vrf_rcv_finish
to deal with the NF_STOLEN case.
There are two cases when skb is stolen.
1. The skb is stolen and freed directly.
There is nothing we need to do, and vrf_rcv_finish isn't invoked.
2. The skb is queued and reinjected again.
The vrf_rcv_finish would be invoked as okfn, so need to free the
skb in it.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 04a68a35ce6d7b54749989f943993020f48fed62 upstream.
Explicitly disable stolen memory when running as a guest in a virtual
machine, since the memory is not mediated between clients and reserved
entirely for the host. The actual size should be reported as zero, but
like every other quirk we want to tell the user what is happening.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99028
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161109103905.17860-1-chris@chris-wilson.co.uk
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b299cde245b0b76c977f4291162cf668e087b408 upstream.
/dev/mem currently allows mmap() mappings that wrap around the end of
the physical address space, which should probably be illegal. It
circumvents the existing STRICT_DEVMEM permission check because the loop
immediately terminates (as the start address is already higher than the
end address). On the x86_64 architecture it will then cause a panic
(from the BUG(start >= end) in arch/x86/mm/pat.c:reserve_memtype()).
This patch adds an explicit check to make sure offset + size will not
wrap around in the physical address type.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e345da82bd6bdfa8492f80b3ce4370acfd868d95 upstream.
The builtin eDP panel in the HP zBook 17 G2 supports 10 bpc,
as advertised by the Laptops product specs and verified via
injecting a fixed edid + photometer measurements, but edid
reports unknown depth, so drivers fall back to 6 bpc.
Add a quirk to get the full 10 bpc.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1492787108-23959-1-git-send-email-mario.kleiner.de@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6a623e07694437ad09f382a13f76cffc32239a7f upstream.
The old 1-bit hamming layout requires ECC data to be placed at a
fixed offset, and not necessarily at the end of the OOB area.
Add this old layout back in order to fix legacy setups.
Fixes: 41b207a70d3a ("mtd: nand: implement the default mtd_ooblayout_ops")
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2d283ede59869159f4bb84ae689258c5caffce54 upstream.
commit c9711ec5250b ("mtd: nand: omap: Clean up device tree support")
caused the parent device name to be changed from "omap2-nand.0"
to "<base address>.nand" (e.g. 30000000.nand on omap3 platforms).
This caused mtd->name to be changed as well. This breaks partition
creation via mtdparts passed by u-boot as it uses "omap2-nand.0"
for the mtd-id.
Fix this by explicitly setting the mtd->name to "omap2-nand.<CS number>"
if it isn't already set by nand_set_flash_node(). CS number is the
NAND controller instance ID.
Fixes: c9711ec5250b ("mtd: nand: omap: Clean up device tree support")
Reported-by: Leto Enrico <enrico.leto@siemens.com>
Reported-by: Adam Ford <aford173@gmail.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 675b11d94ce9baa5eb365a51b35d2793f77c8ab8 upstream.
The clk handling in orion_nand.c had two problems:
- In the probe function, clk_put() was called for an enabled clock,
which violates the API (see documentation for clk_put() in
include/linux/clk.h)
- In the error path of the probe function, clk_put() could be called
twice for the same clock.
In order to clean this up, use the managed function devm_clk_get() and
store the pointer to the clk in the driver data.
Fixes: baffab28b13120694fa3ebab08d3e99667a851d2 ('ARM: Orion: fix driver probe error handling with respect to clk')
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea00353f36b64375518662a8ad15e39218a1f324 upstream.
Laurent Pinchart reported that the Renesas R-Car H2 Lager board (r8a7790)
crashes during suspend tests. Geert Uytterhoeven managed to reproduce the
issue on an M2-W Koelsch board (r8a7791):
It occurs when the PME scan runs, once per second. During PME scan, the
PCI host bridge (rcar-pci) registers are accessed while its module clock
has already been disabled, leading to the crash.
One reproducer is to configure s2ram to use "s2idle" instead of "deep"
suspend:
# echo 0 > /sys/module/printk/parameters/console_suspend
# echo s2idle > /sys/power/mem_sleep
# echo mem > /sys/power/state
Another reproducer is to write either "platform" or "processors" to
/sys/power/pm_test. It does not (or is less likely) to happen during full
system suspend ("core" or "none") because system suspend also disables
timers, and thus the workqueue handling PME scans no longer runs. Geert
believes the issue may still happen in the small window between disabling
module clocks and disabling timers:
# echo 0 > /sys/module/printk/parameters/console_suspend
# echo platform > /sys/power/pm_test # Or "processors"
# echo mem > /sys/power/state
(Make sure CONFIG_PCI_RCAR_GEN2 and CONFIG_USB_OHCI_HCD_PCI are enabled.)
Rafael Wysocki agrees that PME scans should be suspended before the host
bridge registers become inaccessible. To that end, queue the task on a
workqueue that gets frozen before devices suspend.
Rafael notes however that as a result, some wakeup events may be missed if
they are delivered via PME from a device without working IRQ (which hence
must be polled) and occur after the workqueue has been frozen. If that
turns out to be an issue in practice, it may be possible to solve it by
calling pci_pme_list_scan() once directly from one of the host bridge's
pm_ops callbacks.
Stacktrace for posterity:
PM: Syncing filesystems ... [ 38.566237] done.
PM: Preparing system for sleep (mem)
Freezing user space processes ... [ 38.579813] (elapsed 0.001 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
PM: Suspending system (mem)
PM: suspend of devices complete after 152.456 msecs
PM: late suspend of devices complete after 2.809 msecs
PM: noirq suspend of devices complete after 29.863 msecs
suspend debug: Waiting for 5 second(s).
Unhandled fault: asynchronous external abort (0x1211) at 0x00000000
pgd = c0003000
[00000000] *pgd=80000040004003, *pmd=00000000
Internal error: : 1211 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted
4.9.0-rc1-koelsch-00011-g68db9bc814362e7f #3383
Hardware name: Generic R8A7791 (Flattened Device Tree)
Workqueue: events pci_pme_list_scan
task: eb56e140 task.stack: eb58e000
PC is at pci_generic_config_read+0x64/0x6c
LR is at rcar_pci_cfg_base+0x64/0x84
pc : [<c041d7b4>] lr : [<c04309a0>] psr: 600d0093
sp : eb58fe98 ip : c041d750 fp : 00000008
r10: c0e2283c r9 : 00000000 r8 : 600d0013
r7 : 00000008 r6 : eb58fed6 r5 : 00000002 r4 : eb58feb4
r3 : 00000000 r2 : 00000044 r1 : 00000008 r0 : 00000000
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user
Control: 30c5387d Table: 6a9f6c80 DAC: 55555555
Process kworker/1:1 (pid: 20, stack limit = 0xeb58e210)
Stack: (0xeb58fe98 to 0xeb590000)
fe80: 00000002 00000044
fea0: eb6f5800 c041d9b0 eb58feb4 00000008 00000044 00000000 eb78a000 eb78a000
fec0: 00000044 00000000 eb9aff00 c0424bf0 eb78a000 00000000 eb78a000 c0e22830
fee0: ea8a6fc0 c0424c5c eaae79c0 c0424ce0 eb55f380 c0e22838 eb9a9800 c0235fbc
ff00: eb55f380 c0e22838 eb55f380 eb9a9800 eb9a9800 eb58e000 eb9a9824 c0e02100
ff20: eb55f398 c02366c4 eb56e140 eb5631c0 00000000 eb55f380 c023641c 00000000
ff40: 00000000 00000000 00000000 c023a928 cd105598 00000000 40506a34 eb55f380
ff60: 00000000 00000000 dead4ead ffffffff ffffffff eb58ff74 eb58ff74 00000000
ff80: 00000000 dead4ead ffffffff ffffffff eb58ff90 eb58ff90 eb58ffac eb5631c0
ffa0: c023a844 00000000 00000000 c0206d68 00000000 00000000 00000000 00000000
ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 3a81336c 10ccd1dd
[<c041d7b4>] (pci_generic_config_read) from [<c041d9b0>]
(pci_bus_read_config_word+0x58/0x80)
[<c041d9b0>] (pci_bus_read_config_word) from [<c0424bf0>]
(pci_check_pme_status+0x34/0x78)
[<c0424bf0>] (pci_check_pme_status) from [<c0424c5c>] (pci_pme_wakeup+0x28/0x54)
[<c0424c5c>] (pci_pme_wakeup) from [<c0424ce0>] (pci_pme_list_scan+0x58/0xb4)
[<c0424ce0>] (pci_pme_list_scan) from [<c0235fbc>]
(process_one_work+0x1bc/0x308)
[<c0235fbc>] (process_one_work) from [<c02366c4>] (worker_thread+0x2a8/0x3e0)
[<c02366c4>] (worker_thread) from [<c023a928>] (kthread+0xe4/0xfc)
[<c023a928>] (kthread) from [<c0206d68>] (ret_from_fork+0x14/0x2c)
Code: ea000000 e5903000 f57ff04f e3a00000 (e5843000)
---[ end trace 667d43ba3aa9e589 ]---
Fixes: df17e62e5bff ("PCI: Add support for polling PME state on suspended legacy PCI devices")
Reported-and-tested-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reported-and-tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit cef4d02305a06be581bb7f4353446717a1b319ec upstream.
The /proc/bus/pci mmap interface allows the user to specify whether they
want WC or not. Don't let them do so on non-prefetchable BARs.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 17caf56731311c9596e7d38a70c88fcb6afa6a1b upstream.
Don't match MMIO maps with I/O BARs and vice versa.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6bccc7f426abd640f08d8c75fb22f99483f201b4 upstream.
In the PCI_MMAP_PROCFS case when the address being passed by the user is a
'user visible' resource address based on the bus window, and not the actual
contents of the resource, that's what we need to be checking it against.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 433fcf6b7b31f1f233dd50aeb9d066a0f6ed4b9d upstream.
When we have 32 or more CPUs in the affinity mask, we should use a special
constant to specify that to the host. Fix this issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 59c58ceeea9cdc6144d7b0303753e6bd26d87455 upstream.
The memory allocation here needs to be non-blocking. Fix the issue.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f63572dff1421b6ca6abce71d46e03411e605c94 upstream.
CMB doesn't get unmapped until removal while getting remapped on every
reset. Add the unmapping and sysfs file removal to the reset path in
nvme_pci_disable to match the mapping path in nvme_pci_enable.
Fixes: 202021c1a ("nvme : Add sysfs entry for NVMe CMBs when appropriate")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Reviewed-By: Stephen Bates <sbates@raithlin.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 41318a2b82f5d5fe1fb408f6d6e0b22aa557111d upstream.
Add missing endianness conversion when using the USB device-descriptor
idProduct field to apply a hardware quirk.
Fixes: 1ba47da52712 ("uwb: add the i1480 DFU driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f73a7eee900e95404b61408a23a1df5c5811704c upstream.
Ever since commit 091d42e43d ("iommu/vt-d: Copy translation tables from
old kernel") the kdump kernel copies the IOMMU context tables from the
previous kernel. Each device mappings will be destroyed once the driver
for the respective device takes over.
This unfortunately breaks the workflow of mapping and unmapping a new
context to the IOMMU. The mapping function assumes that either:
1) Unmapping did the proper IOMMU flushing and it only ever flush if the
IOMMU unit supports caching invalid entries.
2) The system just booted and the initialization code took care of
flushing all IOMMU caches.
This assumption is not true for the kdump kernel since the context
tables have been copied from the previous kernel and translations could
have been cached ever since. So make sure to flush the IOTLB as well
when we destroy these old copied mappings.
Cc: Joerg Roedel <joro@8bytes.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Anthony Liguori <aliguori@amazon.com>
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Acked-by: David Woodhouse <dwmw@amazon.co.uk>
Fixes: 091d42e43d ("iommu/vt-d: Copy translation tables from old kernel")
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 95d93e271d920dfda369d4740b1cc1061d41fe7f upstream.
TID 7 is a valid value for QoS IEEE 802.11e.
The switch statement that follows states 7 is valid.
Remove function IsACValid and use the default case to filter
invalid TIDs.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 90be652c9f157d44b9c2803f902a8839796c090d upstream.
EPROM_CMD is 2 byte aligned on PCI map so calling with rtl92e_readl
will return invalid data so use rtl92e_readw.
The device is unable to select the right eeprom type.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 867510bde14e7b7fc6dd0f50b48f6753cfbd227a upstream.
BSSIDR has two byte alignment on PCI ioremap correct the write
by swapping to 16 bits first.
This fixes a problem that the device associates fail because
the filter is not set correctly.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit baabd567f87be05330faa5140f72a91960e7405a upstream.
The driver attempts to alter memory that is mapped to PCI device.
This is because tx_fwinfo_8190pci points to skb->data
Move the pci_map_single to when completed buffer is ready to be mapped with
psdec is empty to drop on mapping error.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0cd273bb5e4d1828efaaa8dfd11b7928131ed149 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: e0d3bafd0258 ("V4L/DVB (10954): Add cx231xx USB driver")
Cc: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 65f921647f4c89a2068478c89691f39b309b58f7 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: e0d3bafd0258 ("V4L/DVB (10954): Add cx231xx USB driver")
Cc: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit fff1abc4d54e469140a699612b4db8d6397bfcba upstream.
Make sure to release the snd_card also on a late allocation error.
Fixes: e0d3bafd0258 ("V4L/DVB (10954): Add cx231xx USB driver")
Cc: Sri Deevi <Srinivasa.Deevi@conexant.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 950e252cb469f323740d78e4907843acef89eedb upstream.
Otherwise the i2c transfer functions can read or write beyond the end of
stack or heap buffers.
Signed-off-by: Alyssa Milburn <amilburn@zall.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 821117dc21083a99dd99174c10848d70ff43de29 upstream.
Return an error rather than memcpy()ing beyond the end of the buffer.
Internal callers use appropriate sizes, but digitv_i2c_xfer may not.
Signed-off-by: Alyssa Milburn <amilburn@zall.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 158f0328af86a99d64073851967a02694bff987d upstream.
Fixes "w_scan -f c" complaining with
This dvb driver is *buggy*: the symbol rate limits are undefined - please
report to linuxtv.org)
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ee0fe833d96793853335844b6d99fb76bd12cbeb upstream.
This code copies actual_length-128 bytes from the header, which will
underflow if the received buffer is too small.
Signed-off-by: Alyssa Milburn <amilburn@zall.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d5823511c0f8719a39e72ede1bce65411ac653b7 upstream.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: c4018fa2e4c0 ("[media] dib0700: fix RC support on Hauppauge
Nova-TD")
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a5cb00eb4223458250b55daf03ac7ea5f424d601 upstream.
Clock should be turned off after calling s5p_mfc_init_hw() from the
watchdog worker, like it is already done in the s5p_mfc_open() which also
calls this function.
Fixes: af93574678108 ("[media] MFC: Add MFC 5.1 V4L2 driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit aa58fedb8c7b6cf2f05941d238495f9e2f29655c upstream.
Make sure to check the number of endpoints to avoid accessing memory
beyond the endpoint array should a device lack the expected endpoints.
Note that, as far as I can tell, the gspca framework has already made
sure there is at least one endpoint in the current alternate setting so
there should be no risk for a NULL-pointer dereference here.
Fixes: b517af722860 ("V4L/DVB: gspca_konica: New gspca subdriver for
konica chipset using cams")
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c32b8ec02832df167e16ad659cb11dc148f2ddf upstream.
Interrupt routine must wake process waiting for given interrupt AFTER
updating driver's internal structures and contexts. Doing it in-between
is a serious bug. This patch moves all calls to the wake() function to
the end of the interrupt processing block to avoid potential and real
races, especially on multi-core platforms. This also fixes following issue
reported from clock core (clocks were disabled in interrupt after being
unprepared from the other place in the driver, the stack trace however
points to the different place than s5p_mfc driver because of the race):
WARNING: CPU: 1 PID: 18 at drivers/clk/clk.c:544 clk_core_unprepare+0xc8/0x108
Modules linked in:
CPU: 1 PID: 18 Comm: kworker/1:0 Not tainted 4.10.0-next-20170223-00070-g04e18bc99ab9-dirty #2154
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: pm pm_runtime_work
[<c010d8b0>] (unwind_backtrace) from [<c010a534>] (show_stack+0x10/0x14)
[<c010a534>] (show_stack) from [<c033292c>] (dump_stack+0x74/0x94)
[<c033292c>] (dump_stack) from [<c011cef4>] (__warn+0xd4/0x100)
[<c011cef4>] (__warn) from [<c011cf40>] (warn_slowpath_null+0x20/0x28)
[<c011cf40>] (warn_slowpath_null) from [<c0387a84>] (clk_core_unprepare+0xc8/0x108)
[<c0387a84>] (clk_core_unprepare) from [<c0389d84>] (clk_unprepare+0x24/0x2c)
[<c0389d84>] (clk_unprepare) from [<c03d4660>] (exynos_sysmmu_suspend+0x48/0x60)
[<c03d4660>] (exynos_sysmmu_suspend) from [<c042b9b0>] (pm_generic_runtime_suspend+0x2c/0x38)
[<c042b9b0>] (pm_generic_runtime_suspend) from [<c0437580>] (genpd_runtime_suspend+0x94/0x220)
[<c0437580>] (genpd_runtime_suspend) from [<c042e240>] (__rpm_callback+0x134/0x208)
[<c042e240>] (__rpm_callback) from [<c042e334>] (rpm_callback+0x20/0x80)
[<c042e334>] (rpm_callback) from [<c042d3b8>] (rpm_suspend+0xdc/0x458)
[<c042d3b8>] (rpm_suspend) from [<c042ea24>] (pm_runtime_work+0x80/0x90)
[<c042ea24>] (pm_runtime_work) from [<c01322c4>] (process_one_work+0x120/0x318)
[<c01322c4>] (process_one_work) from [<c0132520>] (worker_thread+0x2c/0x4ac)
[<c0132520>] (worker_thread) from [<c0137ab0>] (kthread+0xfc/0x134)
[<c0137ab0>] (kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
---[ end trace 1ead49a7bb83f0d8 ]---
Fixes: af93574678108 ("[media] MFC: Add MFC 5.1 V4L2 driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5d9854eaea776441b38a9a45b4e6879524c4f48c upstream.
This change undo the change done by 'commit 3bec24747446
("iio: hid-sensor-trigger: Change get poll value function order to avoid
sensor properties losing after resume from S3")' as this breaks some
USB/i2c sensor hubs.
Instead of relying on HW for restoring poll and hysteresis, driver stores
and restores on resume (S3). In this way user space modified settings are
not lost for any kind of sensor hub behavior.
In this change, whenever user space modifies sampling frequency or
hysteresis driver will get the feature value from the hub and store in the
per device hid_sensor_common data structure. On resume callback from S3,
system will set the feature to sensor hub, if user space ever modified the
feature value.
Fixes: 3bec24747446 ("iio: hid-sensor-trigger: Change get poll value function order to avoid sensor properties losing after resume from S3")
Reported-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Ritesh Raj Sarraf <rrs@researchut.com>
Tested-by: Song, Hongyan <hongyan.song@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 84ca8e364acb26aba3292bc113ca8ed4335380fd upstream.
AS3935_WRITE_DATA macro bit is incorrect and the actual write
sequence is two leading zeros.
Cc: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bec444cd1c94c48df409a35ad4e5b143c245c3f7 upstream.
Add missing sanity check on the non-SuperSpeed hub-descriptor length in
order to avoid parsing and leaking two bytes of uninitialised slab data
through sysfs removable-attributes (or a compound-device debug
statement).
Note that we only make sure that the DeviceRemovable field is always
present (and specifically ignore the unused PortPwrCtrlMask field) in
order to continue support any hubs with non-compliant descriptors. As a
further safeguard, the descriptor buffer is also cleared.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2c25a2c818023df64463aac3288a9f969491e507 upstream.
A SuperSpeed hub descriptor does not have any variable-length fields so
bail out when reading a short descriptor.
This avoids parsing and leaking two bytes of uninitialised slab data
through sysfs removable-attributes.
Fixes: dbe79bbe9dcb ("USB 3.0 Hub Changes")
Cc: John Youn <John.Youn@synopsys.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6aeb75e6adfaed16e58780309613a578fe1ee90b upstream.
Fix a division-by-zero in set_termios when debugging is enabled and a
high-enough speed has been requested so that the divisor value becomes
zero.
Instead of just fixing the offending debug statement, cap the baud rate
at the base as a zero divisor value also appears to crash the firmware.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 26cede343656c0bc2c33cdc783771282405c7fb2 upstream.
Drop erroneous cpu_to_le32 when setting the baud rate, something which
corrupted the divisor on big-endian hosts.
Found using sparse:
warning: incorrect type in argument 1 (different base types)
expected unsigned int [unsigned] [usertype] val
got restricted __le32 [usertype] <noident>
Fixes: af2ac1a091bc ("USB: serial mct_usb232: move DMA buffers to heap")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-By: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d7a10dd323993cc40bd37bce8bc570133b0c396 upstream.
In their infinite wisdom, and never ending quest for end user frustration,
Lenovo has decided to use new USB device IDs for the wwan modules in
their 2017 laptops. The actual hardware is still the Sierra Wireless
EM7455 or EM7430, depending on region.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 40dd46048c155b8f0683f468c950a1c107f77a7c upstream.
This patch adds support for Telit ME910 PID 0x1100.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd5ca753fa92fb736b1395db892bd29f78e6d408 upstream.
Drop erroneous le16_to_cpu when returning the USB device speed which is
already in host byte order.
Found using sparse:
warning: cast to restricted __le16
Fixes: 946b960d13c1 ("USB: add driver for iowarrior devices.")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
