| Age | Commit message (Collapse) | Author |
|---|
|
This patch refactors some shutdown code so it can be shared between
ehci_stop() and ehci_shutdown().
This also fixes a couple potential bugs:
- ehci_shutdown() was not locking ehci->lock before halting the HC.
- ehci_shutdown() didn't disable the watchdog and IAA timers.
- ehci_stop() was resetting the host controller when it may have been
running, which the EHCI spec says "may result in undefined behavior".
ehci_stop() was calling port_power() to turn off the ports, which waited
20ms after applying the port change. The msleep was for the case where
the HC might take 20ms to turn the ports on; since we're shutting them
off, we can avoid the msleep and just use ehci_turn_off_ports().
ehci_stop() doesn't need to clear the intr_enable register or revert
ownership of the companion controllers to the BIOS, because the host
controller reset should have done that. There might be a buggy host
controller that doesn't follow the reset rules, but for now we assume
it's redundant code and remove it.
[ A subsequent patch will cancel the timers later ... this version
carries forward existing bugs where timers could get re-armed
after they're canceled. ]
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The at91sam9 chip are ARMv5 so they support preload instructions.
Use preloading to load the FIFO a bit faster.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1075) changes dummy-hcd to dynamically allocate its
platform_device structures, using the core platform_device_alloc()
interface. This is what it should have done all along, because the
dynamically-allocated structures have a release method in the driver
core and are therefore immune to being released after the module has
been unloaded.
Thanks to Richard Purdie for pointing out the need for this change.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Restore some section annotations: they were switched to "__devinit"
while they should have been "__init", because of bogus warnings. The
warnings are now fixed, so the runtime footprint of various drivers
can now shrink a bit. On ARMv5, it's about 600 bytes except for the
Ethernet gadget, where it can save a bit more.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Removing an interface's sysfs files before unregistering the interface
doesn't work properly, because usb_unbind_interface() will reinstall
altsetting 0 and thereby create new sysfs files. This patch (as1074)
removes the files after the unregistration is finished. It's not
quite as clean, but at least it works.
Also, there's no need to check if an interface has been registered
before removing its sysfs files. If it hasn't been registered then
the files won't have been created, so usb_remove_sysfs_intf_files()
will simply do nothing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The kernel is written in C, not C++, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Drivers in the ohci-hcd family should perform certain tasks whenever
their controller device is resumed. These include checking for loss
of power during suspend, turning on port power, and enabling interrupt
requests.
Until now these jobs have been carried out when the root hub is
resumed, not when the controller is. Many drivers work around the
resulting awkwardness by automatically resuming their root hub
whenever the controller is resumed. But this is wasteful and
unnecessary.
To simplify the situation, this patch (as1066) adds a new core
routine, ohci_finish_controller_resume(), which can be used by all the
OHCI-variant drivers. They can call the new routine instead of
resuming their root hubs. And ohci-pci.c can call it instead of using
its own special-purpose handler.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The .suspend and .resume method pointers in struct usb_hcd have not
been fully understood by host-controller driver writers. They are
meant for use with PCI controllers; other platform-specific drivers
generally should not refer to them.
To try and clarify matters, this patch (as1065) renames those methods
to .pci_suspend and .pci_resume. It eliminates corresponding dead code
and bogus references in the ohci-ssb and u132-hcd drivers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Currently EHCI root hubs enumerate with a bDeviceProtocol code
indicating that they possess a Transaction Translator. However the
vast majority of controllers do not; they rely on a companion
controller to handle full- and low-speed communications. This patch
(as1064) changes the root-hub device descriptor to match the actual
situation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
USB is moving to transfering status as a parameter. To ease the transition
urb->status is to be touched only once in a function. The xpad driver has
been overlooked. Dmitry wants this to go through the USB tree.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1063) fixes a bug in the way ohci-hcd resumes its
controllers. It leaves the Master Interrupt Enable bit turned off.
If the root hub is resumed immediately this won't matter. But if the
root hub is suspended (say because no devices are plugged in), it won't
ever wake up by itself.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix a messed up combination of two nested switch statements in
drivers/usb/gadget/dummy_hcd.c.
According to the USB spec (section 5.8.3) the maximum packet size for bulk
endpoints can be 512 for high-speed devices and 8, 16, 32 or 64 for full-speed
devices. Low-speed devices must not have bulk endpoints.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
driver
In drivers/usb/gadget/amd5536udc.c::udc_pci_probe(), sizeof(struct udc)
storage is allocated for 'dev'.
There are many exit points from the function where 'dev' is not free'd but has
also not yet been used for anything. The following patch free's 'dev' at the
return points where it has not yet been used.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch (as1060) makes usb-storage set the DMA alignment mask for
SCSI slaves to match the maxpacket size of the bulk-IN endpoint,
rather than always setting it to 511. For full-speed devices that
mask is too restrictive, and wireless USB devices can have maxpacket
sizes larger than 512.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
G_PRINTER: Bug fix for blocking reads and a fix for a memory leak.
This fixes bugs in blocking IO calls. When the poll() entry point
is called receive transfers will be setup if they have not already
been. Another bug fix is that the poll() entry point now checks the
current receive buffer for data when reporting if any data had been
received. A memory leak was fixed that could have occurred when a
USB reset happened.
Signed-off-by: Craig W. Nadler <craig@nadler.us>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
ohci_hcd_sm501_drv_remove()
platform_get_resource() may return null, so although it seems it will never
do so here unless there's a bug elsewhere, it does no harm to be defensive
and test.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Remove useless @type note for rh_string() and @r note for usb_hcd_irq()
since this two parameters were removed.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I was converting a semaphore in this file to a mutex when I noticed that
this file has some fairly rampant style problems. Practically every line
has spaces instead of tabs .. Once I cleared that up, checkpatch.pl showed
a number of other problem.. I think this file might be a good one to review
for new style checks that could be added..
Below are the only two remaining which I didn't remove.
#5083: FILE: drivers/usb/host/u132-hcd.c:2907:
+ error:
WARNING: labels should not be indented
#5087: FILE: drivers/usb/host/u132-hcd.c:2911:
+ stall:
These labels are actually inside a switch statement, and they are right
under "default:". "default:" appears to be exempt and these other label
should be too, or default shouldn't be exempt.
I also deleted a few lines due to single statements inside { } ,
if (is_error()) {
return;
}
becomes,
if (is_error())
return;
with one line deleted.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Original version of the driver done by Linxb, changes by Harald, and
lots of cleanups by me in order to get it into a mergable state.
Cc: Linxb <xubin.lin@worldplus.com.cn>
Cc: Harald Klein <hari@vt100.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch is for the sierra driver and adds support for a new group of
devices that have a new USB configuration.
This targets kernel 2.6.25-rc7
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch is for the sierra driver and fixes a Compass 597 bug that
allows users to access the SD-Card.
This targets kernel 2.6.25-rc7
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This patch cleans up some of the sierra driver code. Please package this
with the other patches in this group as I would like the driver version
to reflect their changes as well.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
the following patch uses 16 write urbs and a writsize of wMaxPacketSize
* 20. With this patch I get the maximum througput from my linux system
with 20MB/sec read and 15 MB/sec write (full speed 1 MB/sec both)
I also deleted the flag URB_NO_FSBR for the writeurbs, because this
makes my full speed devices significant slower.
Signed-off-by: David Engraf <david.engraf@netcom.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
It ensures that the tty level do not split
the send buffer into 2KB blocks.
Signed-off-by: David Engraf <david.engraf@netcom.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Paolo asked to enable the mmap. I kept it off because I'm do not
entirely understand how it workse these days after ->nopage etc.
But it seems like working somewhat at least.
Signed-Off-By: Pete Zaitcev <zaitcev@gmail.com>
Cc: Paolo Abeni <paolo.abeni@email.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
According to David Brownell, this feature doesn't require an
experimental designation any longer.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Since this USB feature seems non-experimental, remove that dependency.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Since support for the USB Mustek MDC800 Digital Camera has apparently
been around since the beginning of the git repository, it's safe to
assume it's no longer experimental.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Since nothing under the USB serial/ directory seems to be obviously
experimental, remove the EXPERIMENTAL dependency from all of those
Kconfig entries.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Since nothing under the USB misc/ seems to be obviously experimental,
remove the EXPERIMENTAL dependency from those Kconfig entries.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Based on a recent discussion on the Linux USB mailing list, remove the
designation of EXPERIMENTAL from some USB gadget entries, and tag some
of them as DEVELOPMENT.
just for fun, i added a bit of help for gadgetfs, explaining the
race condition.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
|
|
Since there seems to be little reason to mark the current USB storage
features as "EXPERIMENTAL," remove that dependency.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I have got a cypress usb-ide bridge and I would like to tune or monitor
my disk with tools like hdparm, hddtemp or smartctl.
My controller support a way to send raw ATA command to the disk with
something call atacb (see
http://download.cypress.com.edgesuite.net/design_resources/datasheets/contents/cy7c68300c_8.pdf).
Atacb support can be added for each application, but there is some disadvantages :
- all application need to be patched
- A race is possible if there other accesses, because the emulation can
be split in 2 atacb scsi transactions. One for sending the command, one
for reading the register (if ck_cond is set).
I have implemented the emulation in usb-storage with a special proto_handler,
and an unsual entry.
Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
drivers/usb/core/devio.c: In function 'proc_control':
drivers/usb/core/devio.c:657: warning: comparison is always false due to limited range of data type
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The recent changes to this driver cleaned it up a lot, follow that up
by sorting the speed side of things out as well
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Some EHCI fault paths with large control transfers aren't coded. Avoid
problems by rejecting transfers that may need two qTDs (16+ KB). This is
mostly paranoia; even 4 KB transfers are rare, and most HCDs use lower
limits (so it's unlikely anyone would ever try such a thing).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
power.power_state is scheduled for removal. This patch (as1053)
removes all uses of that field from drivers/usb. Almost all of them
were write-only, the most significant exceptions being sl811-hcd.c and
u132-hcd.c.
Part of this patch was written by Pavel Machek.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The ipaq module supports devices with one endpoint only. Some devices,
e.g. Yakumo Delta 300, have more than one endpoint.
This patch fixes support for devices having up to 2 endpoints which used
to work on older kernel versions.
Signed-off-by: Matthias Geissert <matthias.geissert@web.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
It was pointed out that we found and fixed the cause of the "bogus"
fatal IRQ reports some time ago ... this patch removes the code
which was working around that bug ("status" got clobbered), and a
comment which needlessly confused folk reading this code.
This also includes a minor cleanup to the code which fixed that bug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This provides better support for USB "Embedded Host" functionality, which
is a subset of the USB OTG options:
* External hub support can be disabled;
* USB peripherals not whitelisted in "otg_whitelist.h" will be rejected
during enumeration.
These options can allow some savings in software and support.
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The Coverity checker (and Adrian Bunk) spotted an inconsistent NULL check of
port->tty (it's blindly dereferenced later without the check).
Alan Cox confirmed the check can go.
Signed-off-by: Ray Lee <ray-lk@madrabbit.org>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
An extract of the semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression n,d;
@@
(
- (n + d - 1) / d
+ DIV_ROUND_UP(n,d)
|
- (n + (d - 1)) / d
+ DIV_ROUND_UP(n,d)
)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP((n),d)
+ DIV_ROUND_UP(n,d)
@depends on haskernel@
expression n,d;
@@
- DIV_ROUND_UP(n,(d))
+ DIV_ROUND_UP(n,d)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The ftdi_sio driver has no internal locking on the dtr/rts state. Flag
that up for someone to fix.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
