Age | Commit message (Collapse) | Author |
|
commit b8b8b16352cd90c6083033fd4487f04fae935c18 upstream.
In commit 40b368af4b75 ("rtlwifi: Fix alignment issues"), the read
of REG_DBI_READ was changed from 16 to 8 bits. For unknown reasonsi
this change results in reduced stability for the wireless connection.
This regression was located using bisection.
Fixes: 40b368af4b75 ("rtlwifi: Fix alignment issues")
Reported-and-tested-by: James Cameron <quozl@laptop.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eb39a7c0355393c5a8d930f342ad7a6231b552c4 upstream.
The interrupt handler mfgpt_tick() is not robust versus spurious interrupts
which happen before the clock event device is registered and fully
initialized.
The reason is that the safe guard against spurious interrupts solely checks
for the clockevents shutdown state, but lacks a check for detached
state. If the interrupt hits while the device is in detached state it
passes the safe guard and dereferences the event handler call back which is
NULL.
Add the missing state check.
Fixes: 8f9327cbb6e8 ("clockevents/drivers/cs5535: Migrate to new 'set-state' interface")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lkml.kernel.org/r/20171020093103.3317F6004D@linux.fjfi.cvut.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2bbbd96357ce76cc45ec722c00f654aa7b189112 upstream.
At least the Armada XP SoC supports 4GB on a single DRAM window. Because
the size register values contain the actual size - 1, the MSB is set in
that case. For example, the SDRAM window's control register's value is
0xffffffe1 for 4GB (bits 31 to 24 contain the size).
The MBUS driver reads back each window's size from registers and
calculates the actual size as (control_reg | ~DDR_SIZE_MASK) + 1, which
overflows for 32 bit values, resulting in other miscalculations further
on (a bad RAM window for the CESA crypto engine calculated by
mvebu_mbus_setup_cpu_target_nooverlap() in my case).
This patch changes the type in 'struct mbus_dram_window' from u32 to
u64, which allows us to keep using the same register calculation code in
most MBUS-using drivers (which calculate ->size - 1 again).
Fixes: fddddb52a6c4 ("bus: introduce an Marvell EBU MBus driver")
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c503dd38f850be28867ef7a42d9abe5ade81a9bd upstream.
With KASAN and a couple of other patches applied, this driver is one
of the few remaining ones that actually use more than 2048 bytes of
kernel stack:
broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function 'wlc_phy_workarounds_nphy_gainctrl':
broadcom/brcm80211/brcmsmac/phy/phy_n.c:16065:1: warning: the frame size of 3264 bytes is larger than 2048 bytes [-Wframe-larger-than=]
broadcom/brcm80211/brcmsmac/phy/phy_n.c: In function 'wlc_phy_workarounds_nphy':
broadcom/brcm80211/brcmsmac/phy/phy_n.c:17138:1: warning: the frame size of 2864 bytes is larger than 2048 bytes [-Wframe-larger-than=]
Here, I'm reducing the stack size by marking as many local variables as
'static const' as I can without changing the actual code.
This is the first of three patches to improve the stack usage in this
driver. It would be good to have this backported to stabl kernels
to get all drivers in 'allmodconfig' below the 2048 byte limit so
we can turn on the frame warning again globally, but I realize that
the patch is larger than the normal limit for stable backports.
The other two patches do not need to be backported.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dd2349121bb1b8ff688c3ca6a2a0bea9d8c142ca upstream.
The length of the data in the received skb is currently passed into
brcmf_fweh_process_event() as packet_len, but this value is not checked.
event_packet should be followed by DATALEN bytes of additional event
data. Ensure that the received packet actually contains at least
DATALEN bytes of additional data, to avoid copying uninitialized memory
into event->data.
Suggested-by: Mattias Nissler <mnissler@chromium.org>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0fe16195f89173652cf111d7b384941b00c5aabd upstream.
AMD Family 17h uses the KERNCZ SMBus controller. While its documentation
is not publicly available, it is documented in the BIOS and Kernel
Developer’s Guide for AMD Family 15h Models 60h-6Fh Processors.
On this SMBus controller, the port select register is at PMx register
0x02, bit 4:3 (PMx00 register bit 20:19).
Without this patch, the 4 SMBus channels on AMD Family 17h chips are
mirrored and report the same chips on all channels.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c6ebcedbab7ca78984959386012a17b21183e1a3 upstream.
Commit b6c159a9cb69 ("i2c: ismt: Don't duplicate the receive length for
block reads") broke I2C block reads. It aimed to fix normal SMBus block
read, but changed the correct behavior of I2C block read in the process.
According to Documentation/i2c/smbus-protocol, one vital difference
between normal SMBus block read and I2C block read is that there is no
byte count prefixed in the data sent on the wire:
SMBus Block Read: i2c_smbus_read_block_data()
S Addr Wr [A] Comm [A]
S Addr Rd [A] [Count] A [Data] A [Data] A ... A [Data] NA P
I2C Block Read: i2c_smbus_read_i2c_block_data()
S Addr Wr [A] Comm [A]
S Addr Rd [A] [Data] A [Data] A ... A [Data] NA P
Therefore the two transaction types need to be processed differently in
the driver by copying of the dma_buffer as done previously for the
I2C_SMBUS_I2C_BLOCK_DATA case.
Fixes: b6c159a9cb69 ("i2c: ismt: Don't duplicate the receive length for block reads")
Signed-off-by: Pontus Andersson <epontan@gmail.com>
Tested-by: Stephen Douthit <stephend@adiengineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 77913bbcb43ac9a07a6fe849c2fd3bf85fc8bdd8 upstream.
Even though we've zeroed the PDE, the GPU may have cached the PD, so we
need to flush when deleting them.
Noticed while working on replacement MMU code, but a backport might be a
good idea, so let's fix it in the current code too.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 194d68dd051c2dd5ac2b522ae16100e774e8d869 upstream.
G92's seem to require some additional bit of initialization before the
BSP engine can work. It feels like clocks are not set up for the
underlying VLD engine, which means that all commands submitted to the
xtensa chip end up hanging. VP seems to work fine though.
This still allows people to force-enable the bsp engine if they want to
play around with it, but makes it harder for the card to hang by
default.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 72d92e865d1560723e1957ee3f393688c49ca5bf upstream.
The dlc member of the struct rx_msg contains also the ESD_RTR flag to
mark received RTR frames. Without the fix the can_dlc value for received
RTR frames would always be set to 8 by get_can_dlc() instead of the
received value.
Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device")
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ea7d0d69426cab6747ed311c53f4142eb48b9454 upstream.
Many USB 3.1 capable hosts never updated the Serial Bus Release Number
(SBRN) register to USB 3.1 from USB 3.0
xhci driver identified USB 3.1 capable hosts based on this SBRN register,
which according to specs "contains the release of the Universal Serial
Bus Specification with which this Universal Serial Bus Host Controller
module is compliant." but still in october 2017 gives USB 3.0 as
the only possible option.
Make an additional check for USB 3.1 support and enable it if the xHCI
supported protocol capablity lists USB 3.1 capable ports.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 445ef61543da3db5b699f87fb0aa4f227165f6ed upstream.
The sunxi musb has a bug where sometimes it will generate a babble
error on device disconnect instead of a disconnect IRQ. When this
happens the musb controller switches from host mode to device mode
(it clears MUSB_DEVCTL_HM/MUSB_DEVCTL_SESSION and sets
MUSB_DEVCTL_BDEVICE) and gets stuck in this state.
The babble error is misdetected as a bus reset because MUSB_DEVCTL_HM
was cleared.
To fix this, use is_host_active() rather than (devctl & MUSB_DEVCTL_HM)
to detect babble error so that sunxi musb babble recovery can handle it
by restoring the mode. This information is provided by the driver logic
and does not rely on register contents.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6ed05c68cbcae42cd52b8e53b66952bfa9c002ce upstream.
This fixes a kernel oops when unloading the driver due to usb_put_phy
being called after usb_phy_generic_unregister when the device is
detached. Calling usb_phy_generic_unregister causes x->dev->driver to
be NULL in usb_put_phy and results in a NULL pointer dereference.
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit be94a6f6d488b4767662e8949dc62361bd1d6311 upstream.
Add missing break in iio_simple_dummy_write_event_config() for the voltage
threshold event enable attribute. Without this writing to the
in_voltage0_thresh_rising_en always returns -EINVAL even though the change
was correctly applied.
Fixes: 3e34e650db197 ("iio: dummy: Demonstrate the usage of new channel types")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 97819f943063b622eca44d3644067c190dc75039 upstream.
If sending messages with no cable connected, it quickly happens that
there is no more TX context available. Then "gs_can_start_xmit()"
returns with "NETDEV_TX_BUSY" and the upper layer does retry
immediately keeping the CPU busy. To fix that issue, I moved
"atomic_dec(&dev->active_tx_urbs)" from "gs_usb_xmit_callback()" to
the TX done handling in "gs_usb_receive_bulk_callback()". Renaming
"active_tx_urbs" to "active_tx_contexts" and moving it into
"gs_[alloc|free]_tx_context()" would also make sense.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1ac7db63333db1eeff901bfd6bbcd502b4634fa4 upstream.
If the connect status change is set during reset signaling, but
the status remains connected just retry port reset.
This solves an issue with connecting a 90W HP Thunderbolt 3 dock
with a Lenovo Carbon x1 (5th generation) which causes a 30min loop
of a high speed device being re-discovererd before usb ports starts
working.
[...]
[ 389.023845] usb 3-1: new high-speed USB device number 55 using xhci_hcd
[ 389.491841] usb 3-1: new high-speed USB device number 56 using xhci_hcd
[ 389.959928] usb 3-1: new high-speed USB device number 57 using xhci_hcd
[...]
This is caused by a high speed device that doesn't successfully go to the
enabled state after the second port reset. Instead the connection bounces
(connected, with connect status change), bailing out completely from
enumeration just to restart from scratch.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1716332
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2811501e6d8f5747d08f8e25b9ecf472d0dc4c7d upstream.
This keyboard doesn't implement Get String descriptors properly even
though string indexes are valid. What happens is that when requesting
for the String descriptor, the device disconnects and
reconnects. Without this quirk, this loop will continue forever.
Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Владимир Мартьянов <vilgeforce@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 765fb2f181cad669f2beb87842a05d8071f2be85 upstream.
Elatec TWN3 has the union descriptor on data interface. This results in
failure to bind the device to the driver with the following log:
usb 1-1.2: new full speed USB device using streamplug-ehci and address 4
usb 1-1.2: New USB device found, idVendor=09d8, idProduct=0320
usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.2: Product: RFID Device (COM)
usb 1-1.2: Manufacturer: OEM
cdc_acm 1-1.2:1.0: Zero length descriptor references
cdc_acm: probe of 1-1.2:1.0 failed with error -22
Adding the NO_UNION_NORMAL quirk for the device fixes the issue.
`lsusb -v` of the device:
Bus 001 Device 003: ID 09d8:0320
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 32
idVendor 0x09d8
idProduct 0x0320
bcdDevice 3.00
iManufacturer 1 OEM
iProduct 2 RFID Device (COM)
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 67
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 250mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 2
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0020 1x 32 bytes
bInterval 0
CDC Header:
bcdCDC 1.10
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
CDC ACM:
bmCapabilities 0x06
sends break
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
Device Status: 0x0000
(Bus Powered)
Signed-off-by: Maksim Salau <msalau@iotecha.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 31dc3f819bac28a0990b36510197560258ab7421 upstream.
Add device-id entry for (Honeywell) Metrologic MS7820 bar code scanner.
The device has two interfaces (in this mode?); a vendor-specific
interface with two interrupt endpoints and a second HID interface, which
we do not bind to.
Reported-by: Ladislav Dobrovsky <ladislav.dobrovsky@gmail.com>
Tested-by: Ladislav Dobrovsky <ladislav.dobrovsky@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1c0edc3633b56000e18d82fc241e3995ca18a69e upstream.
Andrey used the syzkaller fuzzer to find an out-of-bounds memory
access in usb_get_bos_descriptor(). The code wasn't checking that the
next usb_dev_cap_header structure could fit into the remaining buffer
space.
This patch fixes the error and also reduces the bNumDeviceCaps field
in the header to match the actual number of capabilities found, in
cases where there are fewer than expected.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 845d584f41eac3475c21e4a7d5e88d0f6e410cf7 upstream.
Taking the uurb->buffer_length userspace passes in as a maximum for the
actual urbs transfer_buffer_length causes 2 serious issues:
1) It breaks isochronous support for all userspace apps using libusb,
as existing libusb versions pass in 0 for uurb->buffer_length,
relying on the kernel using the lenghts of the usbdevfs_iso_packet_desc
descriptors passed in added together as buffer length.
This for example causes redirection of USB audio and Webcam's into
virtual machines using qemu-kvm to no longer work. This is a userspace
ABI break and as such must be reverted.
Note that the original commit does not protect other users / the
kernels memory, it only stops the userspace process making the call
from shooting itself in the foot.
2) It may cause the kernel to program host controllers to DMA over random
memory. Just as the devio code used to only look at the iso_packet_desc
lenghts, the host drivers do the same, relying on the submitter of the
urbs to make sure the entire buffer is large enough and not checking
transfer_buffer_length.
But the "USB: devio: Don't corrupt user memory" commit now takes the
userspace provided uurb->buffer_length for the buffer-size while copying
over the user-provided iso_packet_desc lengths 1:1, allowing the user
to specify a small buffer size while programming the host controller to
dma a lot more data.
(Atleast the ohci, uhci, xhci and fhci drivers do not check
transfer_buffer_length for isoc transfers.)
This reverts commit fa1ed74eb1c2 ("USB: devio: Don't corrupt user memory")
fixing both these issues.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 40d829fb2ec636b6b4b0cc95e2546ab9aca04cc9 upstream.
The PIDs for Isochronous data transfers are incorrect
for high bandwidth IN endpoints when the request length
is less than EP wMaxPacketSize.
As per spec correct PIDs for ISOC data transfers are:
1) For request length <= maxpacket
- DATA0,
2) For maxpacket < length <= (2 * maxpacket)
- DATA1, DATA0
3) For (2 * maxpacket) < length <= (3 * maxpacket)
- DATA2, DATA1, DATA0.
But driver always sets PCM fields based on wMaxPacketSize
due to which DATA2 happens even for small requests.
Fix this by setting the PCM field of trb->size depending
on request length rather than fixing it to the value
depending on wMaxPacketSize.
Ideally it shouldn't give any issues as dwc3 will send
0-length packet for next IN token if host sends (even
after receiving a short packet). Windows seems to ignore
this but with MacOS frame loss observed when using f_uvc.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[b-liu@ti.com added following change for v4.9.]
- unsigned int maxp = usb_endpoint_maxp(ep->desc);
+ unsigned int maxp;
+ maxp = usb_endpoint_maxp(ep->desc) & 0x07ff;
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a578884fa0d2768f13d37c6591a9e1ed600482d3 ]
Without the Kconfig dependency, we can get this warning:
warning: ACPI_CPPC_CPUFREQ selects ACPI_CPPC_LIB which has unmet direct dependencies (ACPI && ACPI_PROCESSOR)
Fixes: 5477fb3bd1e8 (ACPI / CPPC: Add a CPUFreq driver for use with CPPC)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 75bf2f6478cab9b0c1d7f5f674a765d1e2ad530e ]
Currently, the IPID and Syndrome are printed on the same line as the
Address. There are cases when we can have a valid Syndrome but not a
valid Address.
For example, the MCA_SYND register can be used to hold more detailed
error info that the hardware folks can use. It's not just DRAM ECC
syndromes. There are some error types that aren't related to memory that
may have valid syndromes, like some errors related to links in the Data
Fabric, etc.
In these cases, the IPID and Syndrome are not printed at the same log
level as the rest of the stanza, so users won't see them on the console.
Console:
[Hardware Error]: CPU:16 (17:1:0) MC22_STATUS[Over|CE|MiscV|-|-|-|-|SyndV|-]: 0xd82000000002080b
[Hardware Error]: Power, Interrupts, etc. Extended Error Code: 2
Dmesg:
[Hardware Error]: CPU:16 (17:1:0) MC22_STATUS[Over|CE|MiscV|-|-|-|-|SyndV|-]: 0xd82000000002080b
, Syndrome: 0x000000010b404000, IPID: 0x0001002e00000002
[Hardware Error]: Power, Interrupts, etc. Extended Error Code: 2
Print the IPID first and on a new line. The IPID should always be
printed on SMCA systems. The Syndrome will then be printed with the IPID
and at the same log level when valid:
[Hardware Error]: CPU:16 (17:1:0) MC22_STATUS[Over|CE|MiscV|-|-|-|-|SyndV|-]: 0xd82000000002080b
[Hardware Error]: IPID: 0x0001002e00000002, Syndrome: 0x000000010b404000
[Hardware Error]: Power, Interrupts, etc. Extended Error Code: 2
Signed-off-by: Yazen Ghannam <Yazen.Ghannam@amd.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1487192182-2474-1-git-send-email-Yazen.Ghannam@amd.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9af02d86e11dc409e5c3de46e81c0a492ba58905 ]
It's much the same as what we did for mwifiex in:
b9da4d2 mwifiex: avoid double-disable_irq() race
"We have a race where the wakeup IRQ might be in flight while we're
calling mwifiex_disable_wake() from resume(). This can leave us
disabling the IRQ twice.
Let's disable the IRQ and enable it in case if we have double-disabled
it."
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3827b64dba27ebadb4faf51f2c91143e01ba1f6d ]
After commit 66d228a2bf03 ("regulator: core: Don't use regulators as
supplies until the parent is bound"), input supplies aren't resolved
if the input supplies parent device has not been bound. This prevent
regulators to hold an invalid reference if its supply parent device
driver probe is deferred.
But this causes issues on some boards where a PMIC's regulator use as
input supply a regulator from another PMIC whose driver is registered
after the driver for the former.
In this case the regulators for the first PMIC will fail to resolve
input supplies on regulators registration (since the other PMIC wasn't
probed yet). And when the core attempts to resolve again latter when
the other PMIC registers its own regulators, it will fail again since
the parent device isn't bound yet.
This will cause some parent supplies to never be resolved and wrongly
be disabled on boot due taking them as unused.
To solve this problem, also attempt to resolve the pending regulators
input supplies before disabling the unused regulators.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 1894054dc1b6e4395048b2c0f28832a3f4320fd3 ]
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4d65491c269729a1e3b375c45e73213f49103d33 ]
In case of unsolicited data for the first sequence
seq_end_offset must be set to minimum of total data length
and FirstBurstLength, so do not add cmd->write_data_done
to the min of total data length and FirstBurstLength.
This patch avoids that with ImmediateData=Yes, InitialR2T=No,
MaxXmitDataSegmentLength < FirstBurstLength that a WRITE command
with IO size above FirstBurstLength triggers sequence error
messages, for example
Set following parameters on target (linux-4.8.12)
ImmediateData = Yes
InitialR2T = No
MaxXmitDataSegmentLength = 8k
FirstBurstLength = 64k
Log in from Open iSCSI initiator and execute
dd if=/dev/zero of=/dev/sdb bs=128k count=1 oflag=direct
Error messages on target
Command ITT: 0x00000035 with Offset: 65536, Length: 8192 outside
of Sequence 73728:131072 while DataSequenceInOrder=Yes.
Command ITT: 0x00000035, received DataSN: 0x00000001 higher than
expected 0x00000000.
Unable to perform within-command recovery while ERL=0.
Signed-off-by: Varun Prakash <varun@chelsio.com>
[ bvanassche: Use min() instead of open-coding it / edited patch description ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b448bf9a0df6093dbadac36979a55ce4e012a677 ]
There are some memory allocation calls in hfi1_create_ctxtdata()
that do not use the numa function parameter. This
can cause cache lines to be filled over QPI.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 39e2afa8d042a53d855137d4c5a689a6f5492b39 ]
After extended testing, it was found that the previous PCIe Gen
3 recipe, which used adaptive CTLE with Preset 4, could cause an
NMI/Surprise Link Down in about 1 in 100 to 1 in 1000 power cycles on
some platforms. New EV data combined with extensive empirical data
indicates that the new recipe should use static CTLE with Preset 6 for
all integrated silicon SKUs.
Fixes: c3f8de0b334c ("IB/hfi1: Add static PCIe Gen3 CTLE tuning")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit e3ccc921b7d8fd1fcd10a00720e09823d8078666 ]
When going to suspend, the I2C registers may be lost because the power to
VDDcore is cut. Restore them when resuming.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c5212b943d4b52a7d9e0d9f747e7ad59c50d31f1 ]
Currently the state is read only after the buffers are relesed.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c2dedf8773e873474535bd4a158609b9eda5403d ]
Reserving doorbell BAR space according to the currently active CPUs
may result in a bug if disabled CPUs are later enabled but no
doorbell space was reserved for them.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit afe981d664aeeebc8d1bcbd7d2070b5432edaecb ]
Driver currently utilizes the same loop variable in two
nested loops.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 36fb7435b6ac4d288a2d4deea8934f9456ab46b6 ]
The mvpp2_txq_bufs_free() function is called upon TX completion to DMA
unmap TX buffers, and free the corresponding SKBs. It gets the
references to the SKB to free and the DMA buffer to unmap from a per-CPU
txq_pcpu data structure.
However, the code currently increments the pointer to the next entry
before doing the DMA unmap and freeing the SKB. It does not cause any
visible problem because for a given SKB the TX completion is guaranteed
to take place on the CPU where the TX was started. However, it is much
more logical to increment the pointer to the next entry once the current
entry has been completely unmapped/released.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4694335dad7357e9b3d7822ab13049014d74d8b0 ]
When the fast blit path fails while attempting to move a buffer from RAM
to VRAM, we fall back to a CPU-based memcpy that cannot handle split VRAM
buffers. Instead of crashing, simply fail the buffer move.
Ideally, we would teach TTM about split buffers so that the fallback still
works in this case, but that is quite involved. So for now, apply the
simplest possible fix.
Fixes: 40361bb1704b ("drm/amdgpu: add VRAM manager v2")
Signed-off-by: Nicolai Hähnle <nicolai.haehnle@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4d7d39a18b8b81511f0b893b7d2203790bf8a58b ]
We accidentally return an uninitialized variable on success.
Fixes: b6ff1b14cdf4 ("[SCSI] scsi_dh: Update EMC handler")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
probed PFs
[ Upstream commit 95f1ba9a24af9769f6e20dfe9a77c863f253f311 ]
In the VF driver, module parameter mlx4_log_num_mgm_entry_size was
mistakenly overwritten -- and in a manner which overrode the
device-managed flow steering option encoded in the parameter.
log_num_mgm_entry_size is a global module parameter which
affects all ConnectX-3 PFs installed on that host.
If a VF changes log_num_mgm_entry_size, this will affect all PFs
which are probed subsequent to the change (by disabling DMFS for
those PFs).
Fixes: 3c439b5586e9 ("mlx4_core: Allow choosing flow steering mode")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 7dd4fcf5b70694dc961eb6b954673e4fc9730dbd ]
On panic, all other CPUs are stopped except the one which had
hit panic. To keep console alive, we need to migrate hvcons irq
to panicked CPU.
Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d939cdfde34f50b95254b375f498447c82190b3e ]
Commit 03a9e24(md linear: fix a race between linear_add() and
linear_congested()) introduces the warnning.
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ca1c39ef76376b67303d01f94fe98bb68bb3861a ]
Reorder error handling labels in order to match the way resources have
been allocated.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6cf1bf636a067eb308cb3a8322b9d6b1844a075d ]
The original github source allowed for the cache-line-size property
to be missing. Since recent firmwares also require this property,
it makes sense to always require it in the driver as well.
If the cache-line-size property is missing, then the driver probe
should fail as no dev since the kernel and dt may be out of sync.
The fix is to add a check for the return value of of_property_read_u32.
Changes V2:
1. Add error message if cache-line-size is missing.
2. Simple check for non-zero return value from
of_property_read_u32.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 47d3a07528ecbbccf53bc4390d70b4e3d1c04fcf ]
The cited commit makes a great job of finding optimal shift/multiplier
values assuming a 10 seconds wrap around, but forgot to change the
overflow_period computation.
It overflows in cyclecounter_cyc2ns(), and the final result is 804 ms,
which is silly.
Lets simply use 5 seconds, no need to recompute this, given how it is
supposed to work.
Later, we will use a timer instead of a work queue, since the new RX
allocation schem will no longer need mlx4_en_recover_from_oom() and the
service_task firing every 250 ms.
Fixes: 31c128b66e5b ("net/mlx4_en: Choose time-stamping shift value according to HW frequency")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6f437d431930ff86e4a971d29321951faadb97c7 ]
Commit 653d2ffd6405 ("qed*: Fix link indication race") introduced another
race - one of the inner functions called from the link-change flow is
explicitly using the slowpath context dedicated PTT instead of gaining
that PTT from the caller. Since this flow can now be called from
a different context as well, we're in risk of the PTT breaking.
Fixes: 653d2ffd6405 ("qed*: Fix link indication race")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit ff4dd73dd2b4806419f8ff65cbce11d5019548d0 ]
Unfortunately, the nla policy was defined to have HWSIM_ATTR_RADIO_NAME
as an NLA_STRING, rather than NLA_NUL_STRING, so we can't use it as a
NUL-terminated string in the kernel.
Rather than break the API, kasprintf() the string to a new buffer to
guarantee NUL termination.
Reported-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit b28ace12661fbcfd90959c1e84ff5a85113a82a1 ]
The max and entry variables are unsigned according to the dt-bindings.
Fix following 3 sparse issues (-Wtypesign):
drivers/irqchip/irq-crossbar.c:222:52: warning: incorrect type in argument 3 (different signedness)
drivers/irqchip/irq-crossbar.c:222:52: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:222:52: got int *<noident>
drivers/irqchip/irq-crossbar.c:245:56: warning: incorrect type in argument 4 (different signedness)
drivers/irqchip/irq-crossbar.c:245:56: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:245:56: got int *<noident>
drivers/irqchip/irq-crossbar.c:263:56: warning: incorrect type in argument 4 (different signedness)
drivers/irqchip/irq-crossbar.c:263:56: expected unsigned int [usertype] *out_value
drivers/irqchip/irq-crossbar.c:263:56: got int *<noident>
Signed-off-by: Franck Demathieu <fdemathieu@gmail.com>
Cc: marc.zyngier@arm.com
Cc: jason@lakedaemon.net
Link: http://lkml.kernel.org/r/20170223094855.6546-1-fdemathieu@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3736d4eb6af37492aeded7fec0072dedd959c842 ]
gcc-4.3 can't decide whether the constant value in
kempld_prescaler[PRESCALER_21] is built-time constant or
not, and gets confused by the logic in do_div():
drivers/watchdog/kempld_wdt.o: In function `kempld_wdt_set_stage_timeout':
kempld_wdt.c:(.text.kempld_wdt_set_stage_timeout+0x130): undefined reference to `__aeabi_uldivmod'
This adds a call to ACCESS_ONCE() to force it to not consider
it to be constant, and leaves the more efficient normal case
in place for modern compilers, using an #ifdef to annotate
why we do this hack.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9f674e48c13dcbc31ac903433727837795b81efe ]
Allocation of new_hash, inside xenvif_new_hash(), always happen
in softirq context, so use GFP_ATOMIC instead of GFP_KERNEL for new
hash allocation.
Signed-off-by: Anoob Soman <anoob.soman@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 299d7572e46f98534033a9e65973f13ad1ce9047 upstream.
Make sure to reset the USB-console port pointer when console setup fails
in order to avoid having the struct usb_serial be prematurely freed by
the console code when the device is later disconnected.
Fixes: 73e487fdb75f ("[PATCH] USB console: fix disconnection issues")
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f5d9644c5fca7d8e8972268598bb516a7eae17f9 upstream.
Dell Wireless 5819/5818 devices are re-branded Sierra Wireless MC74
series which will by default boot with vid 0x413c and pid's 0x81cf,
0x81d0, 0x81d1, 0x81d2.
Signed-off-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|