| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: Add MODULE_DEVICE_TABLE to max8997 and max8998
regulator: fix tps6524x section mismatch
regulator: Remove more wm831x-specific IRQ operations
regulator: add ab8500 enable and raise time delays
regulator: provide consumer interface for fall/rise time
regulator: add set_voltage_time_sel infrastructure
regulator: initialization for ab8500 regulators
regulator: add support for USB voltage regulator
regulator: switch the ab3100 to use enable_time()
Regulator: add suspend-finish API for regulator core.
regulator: fix typo in Kconfig
regulator: Convert WM831x regulators to genirq
regulator: If we fail when setting up a supply say which supply
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Clean up max8997 IRQ namespace
mfd: Fold irq_set_chip/irq_set_handler
mfd: Cleanup irq namespace
mfd: twl6030: Cleanup interrupt handling
mfd: twl4030: Cleanup interrupt handling
mfd: mx8925: Remove irq_desc leftovers
mfd: htc-i2cpld: Cleanup interrupt handling
mfd: htc-egpio: Cleanup interrupt handling
mfd: ezx-pcap: Remvove open coded irq handling
mfd: 88pm860x: Remove unused irq_desc leftovers
mfd: asic3: Cleanup irq handling
mfd: Select MFD_CORE if TPS6105X driver is configured
mfd: Add MODULE_DEVICE_TABLE to rdc321x-southbridge
mfd: Add MAX8997/8966 IRQ control
mfd: Constify i2c_device_id tables
mfd: OLPC: Clean up names to match what OLPC actually uses
mfd: Add mfd_clone_cell(), convert cs5535-mfd/olpc-xo1 to it
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
hwmon: (pmbus) Fix temperature limit register access
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
hwspinlock: depend on OMAP4
ARM: OMAP2+: Fix warnings for GPMC interrupt
OMAP4: PandaBoard: remove unused power regulators
arm: mach-omap2: omap_l3_smx: fix irq handler setup
arm: mach-omap2: devices: fix omap3_l3_init() return value
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
staging: Fix bdops->check_events() misconversion in cyasblkdev_block.c
ide: ensure that we re-run the queue handler
|
|
* 'for-2.6.39/drivers' of git://git.kernel.dk/linux-2.6-block: (122 commits)
cciss: fix lost command issue
drbd: need include for bitops functions declarations
Revert "cciss: Add missing allocation in scsi_cmd_stack_setup and corresponding deallocation"
cciss: fix missed command status value CMD_UNABORTABLE
cciss: remove unnecessary casts
cciss: Mask off error bits of c->busaddr in cmd_special_free when calling pci_free_consistent
cciss: Inform controller we are using 32-bit tags.
cciss: hoist tag masking out of loop
cciss: Add missing allocation in scsi_cmd_stack_setup and corresponding deallocation
cciss: export resettable host attribute
drbd: drop code present under #ifdef which is relevant to 2.6.28 and below
drbd: Fixed handling of read errors on a 'VerifyS' node
drbd: Fixed handling of read errors on a 'VerifyT' node
drbd: Implemented real timeout checking for request processing time
drbd: Remove unused function atodb_endio()
drbd: improve log message if received sector offset exceeds local capacity
drbd: kill dead code
drbd: don't BUG_ON, if bio_add_page of a single page to an empty bio fails
drbd: Removed left over, now wrong comments
drbd: serialize admin requests for new verify run with pending bitmap io
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (f71882fg) Add support for the F71889A
hwmon: (f71882fg) Add support for the F81865F
hwmon: (f71882fg) Document all supported devices
hwmon: (f71882fg) Per-chip fan/temperature input count tables
hwmon: (f71882fg) Secure chip property definition arrays
|
|
* 'for-linus-1' of git://git.infradead.org/mtd-2.6: (49 commits)
mtd: mtdswap: fix compilation warning
mtdswap: kill strict error handling option
mtd: nand: enable software BCH ECC in nand simulator
mtd: nand: add software BCH ECC support
mtd: fix printf format warnings, mostly lack of %zd for size_t, in mtdswap
mtd: sm_rtl: check kmalloc return value
mtd: cfi: add support for AMIC flashes (e.g. A29L160AT)
lib: add shared BCH ECC library
mtd: mxc_nand: fix OOB corruption when page size > 2KiB
mtd: DaVinci: Removed header file that is not required
mtd: pxa3xx_nand: clean the keep configure code
mtd: pxa3xx_nand: mtd scan id process could be defined by driver itself
mtd: pxa3xx_nand: unify prepare command
mtd: pxa3xx_nand: discard wait_for_event,write_cmd,__readid function
mtd: pxa3xx_nand: rework irq logic
mtd: pxa3xx_nand: make scan procedure more clear
mtd: speedtest: fix integer overflow
mtd: mxc_nand: fix read past buffer end
mtd: omap3: nand: report corrected ecc errors
jffs2: remove a trailing white space in commentaries
...
|
|
The device table is required to load modules based on modaliases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: MyungJoo Ham <myungjoo.ham@smasung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Use the combined irq_set_chip_and_handler() function
instead. Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
irq_desc checking in the interrupt demux routine is totally
pointless. The driver sets those lines up, so that cant go away
magically.
Remove the open coded handler magic and use the proper accessor.
This driver needs to be converted to threaded interrupts and buslock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
irq_desc checking in a function which is called with that irq
descriptor locked, is pointless. Equally pointless as the irq desc
check in the interrupt service routine. The driver sets those lines
up, so that cant go away magically.
Remove the open coded handler magic and use the proper accessor.
No need to fiddle with irq_desc in the type setting function. The
original value is in irq_data and the core code stores the new setting
when the return value is 0.
This driver needs to be converted to threaded interrupts and buslock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Remove unused code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Remove the pointless irq_desc check in set_type. This function is
called with that irq descriptor locked. Also remove the write back of
the flow type as the core code does this already when the return value
is 0.
Also store the flow type in the chip data structure, so there is no
need to fiddle in the irq descriptor.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Replace the open coded handler call with the prober accessor. Retrieve
the handler data from desc. That avoids a redundant lookup in the
sparse irq case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
There is no point in checking irq_desc here, as it _is_ available. The
driver configured those lines, so they cannot go away.
The home brewn disabled/note_interrupt magic can be removed as well by
adding a irq_disable callback which avoids the lazy disable.
That driver needs to be converted to threaded interrupts.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Remove the open coded access to irq_desc and use the proper wrappers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The TPS61050/61052 driver uses MFD core code, yet does not specify the
dependency in Kconfig. If it is the only MFD driver configured, compilation
fails with
ERROR: "mfd_add_devices" [drivers/mfd/tps6105x.ko] undefined!
ERROR: "mfd_remove_devices" [drivers/mfd/tps6105x.ko] undefined!
Fix the problem by adding "select MFD_CORE" to the respective Kconfig entry.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The device table is required to load modules based on modaliases.
After adding MODULE_DEVICE_TABLE, below entry will be added to modules.pcimap:
rdc321x-southbridge 0x000017f3 0x00006030 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch enables IRQ handling for MAX8997/8966 chips.
Please note that Fuel-Gauge-related IRQs are not implemented in this
initial release. The fuel gauge module in MAX8997 is identical to
MAX17042, which is already in Linux kernel. In order to use the
already-existing MAX17042 driver for fuel gauge module in MAX8997, the
main interrupt handler of MAX8997 should relay related interrupts to
MAX17042 driver. However, in order to do this, we need to modify
MAX17042 driver as well because MAX17042 driver does not have any
interrupt handlers for now. We are not going to implement this in this
initial release as it is not crucial in basic operations of MAX8997.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Harald Welte <laforge@gnumonks.org>
Cc: Matti Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The cs5535-pms cell doesn't actually need to be cloned, so we can drop that
and simply have the olpc-xo1.c driver use "cs5535-pms" directly.
Also, rename the cs5535-acpi clones to what we actually use for the (currently
out-of-tree) SCI driver. In the process, that fixes a subtle bug in
olpc-xo1.c which broke powerdown on XO-1s.. olpc-xo1-ac-acpi was a typo, not
something that actually existed.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Replace mfd_shared_platform_driver_register with mfd_clone_cell. The
former was called by an mfd client, and registered both a platform driver
and device. The latter is called by an mfd driver, and registers only a
platform device.
The downside of this is that mfd drivers need to be modified whenever
new clients are added that share a cell; the upside is that it fits
Linux's driver model better. It's also simpler.
This also converts cs5535-mfd/olpc-xo1 from the old API. cs5535-mfd
now creates the olpc-xo1-{acpi,pms} devices, while olpc-xo1 binds to
them via platform drivers.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Commit cafb0bfca1 (staging: Convert to bdops->check_events())
incorrectly set bd->user_disk_0->events while initializing
bd->user_disk_1. Fix it.
The problem was spotted by Milton's suspect code pattern detector.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
The conversion to blk_delay_queue() missed parts of IDE.
Add a blk_delay_queue() to ensure that the request handler
gets reinvoked when it needs to.
Note that in all but one place the old plug re-run delay of
3 msecs is used, even though it probably could be shorter
for performance reasons in some of those cases.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Commit 8677011 added auto-update to temperature limit registers.
Unfortunately, the update flag is also used to determine if an attribute
is writable, which results in read-only temperature limit registers.
To fix the problem, pass 'readonly' as separate flag to the function used
to add sensor attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix section mismatch that is caused by init code calling exit code:
pmic_remove() cannot be marked as __devexit.
WARNING: drivers/regulator/tps6524x-regulator.o(.devinit.text+0x205): Section mismatch in reference from the function pmic_probe() to the function .devexit.text:pmic_remove()
The function __devinit pmic_probe() references
a function __devexit pmic_remove().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
pmic_remove() so it may be used outside an exit section.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
These are the last users in the tree.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
This uses the new infrastructure to provide proper delays when
enabling or setting the voltage of one specific regulator.
Cc: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
This exposes the functionality for rise/fall fime when setting
voltage to the consumers.
Cc: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
This makes it possible to set the stabilization time for voltage
regulators in the same manner as enable_time(). The interface
only supports regulators that implements fixed selectors.
Cc: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
The regulators on the AB8500 have a lot of custom
hardware control settings pertaining to 8 external
signals, settings which are board-specific and need
be provided from the platform at startup.
Initialization added for regulators Vana, VextSupply1,
VextSupply2, VextSupply3, Vaux1, Vaux2, Vaux3, VTVout,
Vintcore12, Vaudio, Vdmic, Vamic1, Vamic2, VrefDDR.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This switches the ab3100 core to use the enable_time()
infrastructure from the regulator core.
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
The regulator core had suspend-prepare that turns off the regulators
when entering a system-wide suspend. However, it did not have
suspend-finish that pairs with suspend-prepare and the regulator core
has assumed that the regulator devices and their drivers support
autonomous recover at resume.
This patch adds regulator_suspend_finish that pairs with the
previously-existed regulator_suspend_prepare. The function
regulator_suspend_finish turns on the regulators that have always_on set
or positive use_count so that we can reset the regulator states
appropriately at resume.
In regulator_suspend_finish, if has_full_constraints, it disables
unnecessary regulators.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
Updates
v3
comments corrected (Thanks to Igor)
v2
disable unnecessary regulators (Thanks to Mark)
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
Fix typo: s/TPS695x0/TPS659x0/
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
Makes it a bit easier to identify if it's a problem with the supplies,
the usual error would be omitting the supply name entirely.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Add support for the Fintek F81865F. It's essentially compatible with
the F71882FG, but has fewer inputs: 7 voltage, 2 temperature and 2 fan
inputs only.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
The list of supported devices was not always well documented in all
places. Clarify and list all devices in documentation, Kconfig and
the driver itself.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Use tables to list the count of fan and temperature inputs for all
supported chips, almost similar to (but more simple than) what is
already done for voltage inputs. This avoids repeating the same tests
in different functions, and will make it easier to add support for
chips with a different count of fan or temperature inputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Using C99-style array initialization will ensure definitions won't
drift if the chips enum gets new values added.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'syscore' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
Introduce ARCH_NO_SYSDEV_OPS config option (v2)
cpufreq: Use syscore_ops for boot CPU suspend/resume (v2)
KVM: Use syscore_ops instead of sysdev class and sysdev
PCI / Intel IOMMU: Use syscore_ops instead of sysdev class and sysdev
timekeeping: Use syscore_ops instead of sysdev class and sysdev
x86: Use syscore_ops instead of sysdev classes and sysdevs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Fix test of uninitialized netdev
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (55 commits)
[SCSI] tcm_loop: Add multi-fabric Linux/SCSI LLD fabric module
[SCSI] qla4xxx: Use polling mode for disable interrupt mailbox completion
[SCSI] Revert "[SCSI] Retrieve the Caching mode page"
[SCSI] bnx2fc: IO completion not processed due to missed wakeup
[SCSI] qla4xxx: Update driver version to 5.02.00-k6
[SCSI] qla4xxx: masking required bits of add_fw_options during initialization
[SCSI] qla4xxx: added new function qla4xxx_relogin_all_devices
[SCSI] qla4xxx: add support for ql4xsess_recovery_tmo cmd line param
[SCSI] qla4xxx: Add support for ql4xmaxqdepth command line parameter
[SCSI] qla4xxx: cleanup function qla4xxx_process_ddb_changed
[SCSI] qla4xxx: Prevent other port reinitialization during remove_adapter
[SCSI] qla4xxx: remove unused ddb flag DF_NO_RELOGIN
[SCSI] qla4xxx: cleanup DDB relogin logic during initialization
[SCSI] qla4xxx: Do not retry ISP82XX initialization if H/W state is failed
[SCSI] qla4xxx: Do not send mbox command if FW is in failed state
[SCSI] qla4xxx: cleanup qla4xxx_initialize_ddb_list()
[SCSI] ses: add subenclosure support
[SCSI] bnx2fc: Bump version to 1.0.1
[SCSI] bnx2fc: Remove unnecessary module state checks
[SCSI] bnx2fc: Fix MTU issue by using static MTU
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kdb: add usage string of 'per_cpu' command
kgdb,x86_64: fix compile warning found with sparse
kdb: code cleanup to use macro instead of value
kgdboc,kgdbts: strlen() doesn't count the terminator
|
