| Age | Commit message (Collapse) | Author |
|---|
|
Code for creating single byte llis is present at several places. Create a
routine to avoid code redundancy.
Also, we don't need one lli per single byte transfer, we can have single lli to
do all single byte transfer.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
MIN(width))
max_bytes_per_lli = bd.srcbus.buswidth * PL080_CONTROL_TRANSFER_SIZE_MASK;
This is confirmed by ARM support guys.
Below is summary of mail exchange with them:
[Viresh] What is the total data to be transferred in case source and destination
bus widths are different. Suppose, source bus width is 2 bytes and destination
is 4 bytes. Now in order to transfer 80 bytes, what should be value of
TransferSize field in control reg: 40? or 20?.
[David from ARM] The value that is programmed into the TransferSize field should
be the number of <SourceWidth> transfers needed to achieve the required data
transfer.
So, to transfer 80 bytes, with a Source Width of 2, the TransferSize field =
should be programmed with:
Total transfer size
------------------- = 40
<source width>
[Viresh] Will this change if source is 4 bytes and dest is 2?
[David] Yes - the calculation then becomes:
Total transfer size
------------------- =20
<source width>
Also, max_bytes_per_lli must be calculated after fixing src and dest widths not
before that. So move this code to the correct place.
This patch also removes max_bytes_per_lli from earlier print message, as till
that point max_bytes_per_lli is unknown.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Pl080 Manual says: "Bursts do not cross the 1KB address boundary"
We can program the controller to cross 1 KB boundary on a burst and controller
can take care of this boundary condition by itself.
Following is the discussion with ARM Technical Support Guys (David):
[Viresh] Manual says: "Bursts do not cross the 1KB address boundary"
What does that actually mean? As, Maximum size transferable with a single LLI is
4095 * 4 =16380 ~ 16KB. So, if we don't have src/dest address aligned to burst
size, we can't use this big of an LLI.
[David] There is a difference between bursts describing the total data
transferred by the DMA controller and AHB bursts. Bursts described by the
programmable parameters in the PL080 have no direct connection with the bursts
that are seen on the AHB bus.
The statement that "Bursts do not cross the 1KB address boundary" in the TRM is
referring to AHB bursts, where this limitation is a requirement of the AHB spec.
You can still issue bursts within the PL080 that are in excess of 1KB. The
PL080 will make sure that its bursts are broken down into legal AHB bursts which
will be formatted to ensure that no AHB burst crosses a 1KB boundary.
Based on above discussion, this patch removes all code related to 1 KB boundary
as we are not required to handle this in driver.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Currently, if error interrupt occurs, nothing is done in interrupt handler (just
clearing the interrupts). We must somehow indicate this to the user that DMA is
over, due to ERR interrupt or TC interrupt.
So, this patch just schedules existing tasklet, with a print showing error
interrupt has occurred on which channels.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
We have just executed following in pl08x_get_phy_channel():
ch->signal = -1;
We don't have to compare "ch->signal < 0", as this will always be true.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Simply writing 1 on bit 0 is sufficient instead of reading and clearing bits.
Also as per manual, for bit 3-31 of DMACConfiguration register:
"read undefined, write as 0"
So, we must not rely on values read from this registers bit 3-31.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Insert notifiers for the runtime PM API. With this the runtime PM layer kicks in
to action where used.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
For 8 memory and 16 slave channels 35 boot print lines are printed. And that is
too much. Most of this would be more useful for debugging. So moving few of them
to dev_dbg instead of dev_info. Now only 3 prints will be printed.
This also rearrange one of the debug message to fit into two lines.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Similar comment is present over routine also pl08x_choose_master_bus(). Keeping
one of them. Also rewrite that comment to convey message clearly.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
As mentioned in Documentation/CodingStyle,
The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not.
This patch replaces (struct xyz) with *ptr at several occurrences in driver.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Header files included in driver are not present in alphabetical order. Rearrange
them in alphabetical order.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
There were few formatting related issues in code. This patch fixes them.
Fixes include:
- Remove extra blank lines
- align code to 80 cols
- combine several lines to one line
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In this driver, we can trigger cyclic transfer on peripherals-DMA interfaces.
It is dependent on driver implementation but cannot depend on a platform
property: we remove the dma_has_cap(DMA_CYCLIC, ) test which has no meaning.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Cyclic property and paused state are encoded as bits in the channel status
bitfield. Tests of those bits are wrapped in convenient helper functions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Save/restore dma controller state across a suspend-resume sequence.
The prepare() function will wait for the non-cyclic channels to become idle.
It also deals with cyclic operations with the start at next period while
resuming.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
dmaengine routines can be called from interrupt context and with
interrupts disabled. Whereas spin_unlock_bh can't be called from
such contexts. So this patch converts all spin_lock* routines
to irqsave variants.
Also, spin_lock() used in tasklet is converted to irqsave variants,
as tasklet can be interrupted, and dma requests from such interruptions
may also call spin_lock.
Idea from dw_dmac patch by Viresh Kumar.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
After calling mxs_dma_disable_chan() for a channel, that channel
becomes unusable because some controller registers can only be written
when the clock is enabled via CLKGATE.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In case, some error occurs while doing memcpy transfers, we must terminate all
transfers physically too. This is achieved by calling device_control() routine
with TERMINATE_ALL as parameter.
This is also required to be done in case module is removed while we are in
middle of some transfers.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Commit d006199e72a9 ("serial: sh-sci: Regtype probing doesn't need to be
fatal.") made sci_init_single() return when sci_probe_regmap() succeeds,
although it should return when sci_probe_regmap() fails. This causes
systems using the serial sh-sci driver to crash during boot.
Fix the problem by using the right return condition.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Compute protocol sequence numbers and fragment IDs using MD5.
crypto: Move md5_transform to lib/md5.c
|
|
Computers have become a lot faster since we compromised on the
partial MD4 hash which we use currently for performance reasons.
MD5 is a much safer choice, and is inline with both RFC1948 and
other ISS generators (OpenBSD, Solaris, etc.)
Furthermore, only having 24-bits of the sequence number be truly
unpredictable is a very serious limitation. So the periodic
regeneration and 8-bit counter have been removed. We compute and
use a full 32-bit sequence number.
For ipv6, DCCP was found to use a 32-bit truncated initial sequence
number (it needs 43-bits) and that is fixed here as well.
Reported-by: Dan Kaminsky <dan@doxpara.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Runtime: Allow _put_sync() from interrupts-disabled context
PM / Domains: Fix pm_genpd_poweron()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (38 commits)
acer-wmi: support Lenovo ideapad S205 wifi switch
acerhdf.c: spaces in aliased changed to *
platform-drivers-x86: ideapad-laptop: add missing ideapad_input_exit in ideapad_acpi_add error path
x86 driver: fix typo in TDP override enabling
Platform: fix samsung-laptop DMI identification for N150/N210/220/N230
dell-wmi: Add keys for Dell XPS L502X
platform-drivers-x86: samsung-q10: make dmi_check_callback return 1
Platform: Samsung Q10 backlight driver
platform-drivers-x86: intel_scu_ipc: convert to DEFINE_PCI_DEVICE_TABLE
platform-drivers-x86: intel_rar_register: convert to DEFINE_PCI_DEVICE_TABLE
platform-drivers-x86: intel_menlow: add missing return AE_OK for intel_menlow_register_sensor()
platform-drivers-x86: intel_mid_thermal: fix memory leak
platform-drivers-x86: msi-wmi: add missing sparse_keymap_free in msi_wmi_init error path
Samsung Laptop platform driver: support N510
asus-wmi: add uwb rfkill support
asus-wmi: add gps rfkill support
asus-wmi: add CWAP support and clarify the meaning of WAPF bits
asus-wmi: return proper value in store_cpufv()
asus-wmi: check for temp1 presence
asus-wmi: add thermal sensor
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/trace: Fix compile error when CONFIG_XEN_PRIVILEGED_GUEST is not set
xen: Fix misleading WARN message at xen_release_chunk
xen: Fix printk() format in xen/setup.c
xen/tracing: it looks like we wanted CONFIG_FTRACE
xen/self-balloon: Add dependency on tmem.
xen/balloon: Fix compile errors - missing header files.
xen/grant: Fix compile warning.
xen/pciback: remove duplicated #include
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
Battery: sysfs_remove_battery(): possible circular locking
|
|
Two additional savage4 variants were added, but the S3_SAVAGE4_SERIES
macro was incompletely modified, resulting in a false positive detection
of a savage4 card regardless of which savage card is actually present.
For non-savage4 series cards, such as a Savage/IX-MV card, this results
in garbled video and/or a hard-hang at boot time. Fix this by changing
an '||' to an '&&' in the S3_SAVAGE4_SERIES macro.
Signed-off-by: John P. Stanley <jpsinthemix@verizon.net>
Reviewed-by: Tormod Volden <debian.tormod@gmail.com>
[ The macros have incomplete parenthesis too, but whatever .. -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
Commit 9c921c22a7f33397a6774d7fa076db9b6a0fd669
Author: Lan Tianyu <tianyu.lan@intel.com>
ACPI / Battery: Resolve the race condition in the sysfs_remove_battery()
fixed BUG https://bugzilla.kernel.org/show_bug.cgi?id=35642 , but as a side
effect made lockdep unhappy with sysfs_remove_battery():
[14818.477168]
[14818.477170] =======================================================
[14818.477200] [ INFO: possible circular locking dependency detected ]
[14818.477221] 3.1.0-dbg-07865-g1280ea8-dirty #668
[14818.477236] -------------------------------------------------------
[14818.477257] s2ram/1599 is trying to acquire lock:
[14818.477276] (s_active#8){++++.+}, at: [<ffffffff81169147>] sysfs_addrm_finish+0x31/0x5a
[14818.477323]
[14818.477325] but task is already holding lock:
[14818.477350] (&battery->lock){+.+.+.}, at: [<ffffffffa0047278>] sysfs_remove_battery+0x10/0x4b [battery]
[14818.477395]
[14818.477397] which lock already depends on the new lock.
[14818.477399]
[..]
[14818.479121] stack backtrace:
[14818.479148] Pid: 1599, comm: s2ram Not tainted 3.1.0-dbg-07865-g1280ea8-dirty #668
[14818.479175] Call Trace:
[14818.479198] [<ffffffff814828c3>] print_circular_bug+0x293/0x2a4
[14818.479228] [<ffffffff81070cb5>] __lock_acquire+0xfe4/0x164b
[14818.479260] [<ffffffff81169147>] ? sysfs_addrm_finish+0x31/0x5a
[14818.479288] [<ffffffff810718d2>] lock_acquire+0x138/0x1ac
[14818.479316] [<ffffffff81169147>] ? sysfs_addrm_finish+0x31/0x5a
[14818.479345] [<ffffffff81168a79>] sysfs_deactivate+0x9b/0xec
[14818.479373] [<ffffffff81169147>] ? sysfs_addrm_finish+0x31/0x5a
[14818.479405] [<ffffffff81169147>] sysfs_addrm_finish+0x31/0x5a
[14818.479433] [<ffffffff81167bc5>] sysfs_hash_and_remove+0x54/0x77
[14818.479461] [<ffffffff811681b9>] sysfs_remove_file+0x12/0x14
[14818.479488] [<ffffffff81385bf8>] device_remove_file+0x12/0x14
[14818.479516] [<ffffffff81386504>] device_del+0x119/0x17c
[14818.479542] [<ffffffff81386575>] device_unregister+0xe/0x1a
[14818.479570] [<ffffffff813c6ef9>] power_supply_unregister+0x23/0x27
[14818.479601] [<ffffffffa004729c>] sysfs_remove_battery+0x34/0x4b [battery]
[14818.479632] [<ffffffffa004778f>] battery_notify+0x2c/0x3a [battery]
[14818.479662] [<ffffffff8148fe82>] notifier_call_chain+0x74/0xa1
[14818.479692] [<ffffffff810624b4>] __blocking_notifier_call_chain+0x6c/0x89
[14818.479722] [<ffffffff810624e0>] blocking_notifier_call_chain+0xf/0x11
[14818.479751] [<ffffffff8107e40e>] pm_notifier_call_chain+0x15/0x27
[14818.479770] [<ffffffff8107ee1a>] enter_state+0xa7/0xd5
[14818.479782] [<ffffffff8107e341>] state_store+0xaa/0xc0
[14818.479795] [<ffffffff8107e297>] ? pm_async_store+0x45/0x45
[14818.479807] [<ffffffff81248837>] kobj_attr_store+0x17/0x19
[14818.479820] [<ffffffff81167e27>] sysfs_write_file+0x103/0x13f
[14818.479834] [<ffffffff81109037>] vfs_write+0xad/0x13d
[14818.479847] [<ffffffff811092b2>] sys_write+0x45/0x6c
[14818.479860] [<ffffffff81492f92>] system_call_fastpath+0x16/0x1b
This patch introduces separate lock to struct acpi_battery to
grab in sysfs_remove_battery() instead of battery->lock.
So fix by Lan Tianyu is still there, we just grab independent lock.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Currently the use of pm_runtime_put_sync() is not safe from
interrupts-disabled context because rpm_idle() will release the
spinlock and enable interrupts for the idle callbacks. This enables
interrupts during a time where interrupts were expected to be
disabled, and can have strange side effects on drivers that expected
interrupts to be disabled.
This is not a bug since the documentation clearly states that only
_put_sync_suspend() is safe in IRQ-safe mode.
However, pm_runtime_put_sync() could be made safe when in IRQ-safe
mode by releasing the spinlock but not re-enabling interrupts, which
is what this patch aims to do.
Problem was found when using some buggy drivers that set
pm_runtime_irq_safe() and used _put_sync() in interrupts-disabled
context.
Reported-by: Colin Cross <ccross@google.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
The local variable ret is defined twice in pm_genpd_poweron(), which
causes this function to always return 0, even if the PM domain's
.power_on() callback fails, in which case an error code should be
returned.
Remove the wrong second definition of ret and additionally remove an
unnecessary definition of wait from pm_genpd_poweron().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
The AMW0 function in acer-wmi works on Lenovo ideapad S205 for control
the wifi hardware state. We also found there have a 0x78 EC register
exposes the state of wifi hardware switch on the machine.
So, add this patch to support Lenovo ideapad S205 wifi hardware switch
in acer-wmi driver.
Reference: bko#37892
https://bugzilla.kernel.org/show_bug.cgi?id=37892
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Thomas Renninger <trenn@suse.de>
Tested-by: Florian Heyer <heyho@flanto.de>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
It seems that aliases shouldn't contain spaces, as
module-init-tools uses them as delimeters in module.alias file
Signed-off-by: Anton V. Boyarshinov <boyarsh@altlinux.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
ideapad_acpi_add error path
In the case of ideapad_backlight_init() failure,
we need to free the resources allocated by ideapad_input_init().
Aslo drop __devexit annotation for ideapad_input_exit() because
we also call it in ideapad_acpi_add() error path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
When enabling turbo, we need to set both the TDC and TDP bits. IIRC
only the TDC one actually matters, but fix it up anyway since the
current code is confusing.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Some samsung latop of the N150/N2{10,20,30} serie are badly detected by the samsung-laptop platform driver, see bug # 36082.
It appears that N230 identifies itself as N150/N210/N220/N230 whereas the other identify themselves as N150/N210/220.
This patch attemtp fix #36082 allowing correct identification for all the said netbook model.
Reported-by: Daniel Eklöf <daniel@ekloef.se>
Signed-off-by: Thomas Courbon <thcourbon@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
All of these keys are being reported on the keyboard
controller but are also generating WMI events. Add them
to the legacy keymap to silence the noise.
BugLink: http://bugs.launchpad.net/bugs/815914
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
We only care about if there is any successful match from the dmi table
or no match at all, we can make dmi_check_system return immediately if
we have a successful match instead of iterate thorough the whole table.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
This adds backlight control on the Samsung Q10 laptop, which does not support
the SABI interface. Also tested successfully on the Dell Latitude X200.
Signed-off-by: Frederick van der Wyck <fvanderwyck@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
And also remove unused variable 'my_id_table'.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
intel_menlow_register_sensor()
Otherwise, the error path will always be executed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
The memory for td_info which is allocated in initialize_sensor()
should be properly kfreed in mid_thermal_probe() error patch and
mid_thermal_remove().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
msi_wmi_init error path
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
The N510 benefits from this code as well. Below is a patch to include support.
Signed-off-by: Jouke Witteveen <j.witteveen@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
ref: http://dev.iksaif.net/projects/3/wiki/Asus-laptop_WAPF
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Cc: stable@kernel.org
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
