| Age | Commit message (Collapse) | Author |
|---|
|
If doc_probe_device() returned an ERR_PTR, then we accidentally saved
that to docg3_floors[floor] = mtd; which gets derefenced in the error
handling when we call doc_release_device().
I've reworked the error handling to take care of that and hopefully
make it a little simpler.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
As each docg3 chip has 2 protection areas (DPS0 and DPS1),
and because theses areas can prevent user access to the chip
data, add for each floor the sysfs entries which insert the
protection key into the right DPS.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Docg3 chips can work in 3 modes : normal MLC mode, fast
mode and reliable mode. Normally, as docg3 is a MLC chip, it
should be configured to work in normal mode.
In both normal mode, each page is distinct. This
means that writing to page 12 of blocks 14,15 writes only to
that page, and reading from page 12 of blocks 14,15 reads
only from that page.
In reliable and fast modes, pages are coupled by pairs, and
are clones one of each other. This means that the available
capacity of the chip is halved. Pages are coupled in each
block, and page of index 2*n contains the same data as page
2*n+1 of the same block.
In fast mode, the reads occur a bit faster, but are a bit
less reliable that in normal mode.
When reading from page 2*n, the chip reads bytes from both
page 2*n and page 2*n+1, makes a logical and for each byte,
and returns the result. As programming a page means
"clearing bits", even if a bit was not cleared on one page
because the flash is worn out, the other page has the bit
cleared, and the result of the "AND" gives a correct result.
When writing to page 2*n, the chip writes data to both page
2*n and page 2*n+1.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Add functions to powerdown and powerup from suspend, in
order to save power.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Credit for discovering the BCH algorith parameters, and bit
reversing algorithm is to be give to Mike Dunn and Ivan
Djelic.
The BCH correction code relied upon the BCH library, where
all data and ECC is bit-reversed. The BCH library works
correctly when each input byte is bit-reversed, and
accordingly ECC output is also bit-reversed.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Map the developped write and erase functions into the mtd
structure.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Add erase capability to the docg3 driver. The erase block is
made of 2 physical blocks, as both share all 64 pages. That
makes an erase block of at least 64 kBytes.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Add write capability to the docg3 driver. The writes are
possible on a single page (512 bytes + 16 bytes), even if
that page is split on 2 physical pages on 2 blocks (each on
one plane).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Add OOB buffer area to store the OOB data until the actual
page is written, so that it can be completed by hardware ECC
generator.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Add the required registers and commands to erase and write
flash pages / blocks.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Add OOB layout description for docg3, so that userspace can
use this information to setup the data for write_oob().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Add support for multiple floors, ie. cascaded docg3
chips. There might be 4 docg3 chips cascaded, sharing the
same address space, and providing up to 4 times the storage
capacity of a unique chip.
Each floor will be seen as an independant mtd device.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Fix the docg3 reads to be able to cope with all possible
data buffer / oob buffer / file mode combinations from
docg3_read_oob().
This especially ensures that raw reads do not use ECC
corrections, and AUTOOOB and PLACEOOB do use ECC
correction.
The approach is to empty docg3_read() and make it a wrapper
to docg3_read_oob(). As docg3_read_oob() handles all the
funny cases (no data buffer but oob buffer, data buffer but
no oob buffer, ...), docg3_read() is just a special use of
docg3_read_oob().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
BCH registers are contiguous, not on every byte. Fix the
register definitions.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
The protection areas boundaries were on 16bit registers, not
8bit. This is consistent with block numbers, which can
extend up to 4096 on bigger chips (and is 2048 on the
docg3).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Writeb was incorrectly traced as a 16 bits write, instead of
a 8 bits write. Fix it by tracing the correct width.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Change the NOP debug log verbosity to very verbose to
unburden log analysis.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Ivan Djelic <ivan.djelic@parrot.com>
Reviewed-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Making MTD_NAND_OMAP2 depend on ARCH_OMAP2PLUS instead of
oring with ARCH2/3/4.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
This patch allows each CFI device map to use its own endianness. The
globally defined CFI endianness (CONFIG_MTD_CFI_NOSWAP,
CONFIG_MTD_CFI_BE_BYTE_SWAP or CONFIG_MTD_CFI_LE_BYTE_SWAP) becomes the
default value which can be overridden by a driver for a particular device.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Some error paths in mtd_blkdevs were fixed in the following commit:
commit 94735ec4044a6d318b83ad3c5794e931ed168d10
mtd: mtd_blkdevs: fix error path in blktrans_open
But on these error paths, the block device's `dev->open' count is
already incremented before we check for errors. This meant that, while
the error path was handled correctly on the first time through
blktrans_open(), the device is erroneously considered already open on
the second time through.
This problem can be seen, for instance, when a UBI volume is
simultaneously mounted as a UBIFS partition and read through its
corresponding gluebi mtdblockX device. This results in blktrans_open()
passing its error checks (with `dev->open > 0') without actually having
a handle on the device. Here's a summarized log of the actions and
results with nandsim:
# modprobe nandsim
# modprobe mtdblock
# modprobe gluebi
# modprobe ubifs
# ubiattach /dev/ubi_ctrl -m 0
...
# ubimkvol /dev/ubi0 -N test -s 16MiB
...
# mount -t ubifs ubi0:test /mnt
# ls /dev/mtdblock*
/dev/mtdblock0 /dev/mtdblock1
# cat /dev/mtdblock1 > /dev/null
cat: can't open '/dev/mtdblock4': Device or resource busy
# cat /dev/mtdblock1 > /dev/null
CPU 0 Unable to handle kernel paging request at virtual address
fffffff0, epc == 8031536c, ra == 8031f280
Oops[#1]:
...
Call Trace:
[<8031536c>] ubi_leb_read+0x14/0x164
[<8031f280>] gluebi_read+0xf0/0x148
[<802edba8>] mtdblock_readsect+0x64/0x198
[<802ecfe4>] mtd_blktrans_thread+0x330/0x3f4
[<8005be98>] kthread+0x88/0x90
[<8000bc04>] kernel_thread_helper+0x10/0x18
Cc: stable@kernel.org [3.0+]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Macronix MX30LF1208AA is a 512 Mbit NAND with device code 0xF0.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
Macronix is produing SLC NAND MX30LF1208AA, so add their manufacturer
code to the manufacturer lists.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] omap3isp: Fix crash caused by subdevs now having a pointer to devnodes
|
|
* 'for-linus' of git://neil.brown.name/md:
md/bitmap: It is OK to clear bits during recovery.
md: don't give up looking for spares on first failure-to-add
md/raid5: ensure correct assessment of drives during degraded reshape.
md/linear: fix hot-add of devices to linear arrays.
|
|
commit d0a4bb492772ce5c4bdfba3744a99ed6f6fb238f introduced a
regression which is annoying but fairly harmless.
When writing to an array that is undergoing recovery (a spare
in being integrated into the array), writing to the array will
set bits in the bitmap, but they will not be cleared when the
write completes.
For bits covering areas that have not been recovered yet this is not a
problem as the recovery will clear the bits. However bits set in
already-recovered region will stay set and never be cleared.
This doesn't risk data integrity. The only negatives are:
- next time there is a crash, more resyncing than necessary will
be done.
- the bitmap doesn't look clean, which is confusing.
While an array is recovering we don't want to update the
'events_cleared' setting in the bitmap but we do still want to clear
bits that have very recently been set - providing they were written to
the recovering device.
So split those two needs - which previously both depended on 'success'
and always clear the bit of the write went to all devices.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Before performing a recovery we try to remove any spares that
might not be working, then add any that might have become relevant.
Currently we abort on the first spare that cannot be added.
This is a false optimisation.
It is conceivable that - depending on rules in the personality - a
subsequent spare might be accepted.
Also the loop does other things like count the available spares and
reset the 'recovery_offset' value.
If we abort early these might not happen properly.
So remove the early abort.
In particular if you have an array what is undergoing recovery and
which has extra spares, then the recovery may not restart after as
reboot as the could of 'spares' might end up as zero.
Reported-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
While reshaping a degraded array (as when reshaping a RAID0 by first
converting it to a degraded RAID4) we currently get confused about
which devices are in_sync. In most cases we get it right, but in the
region that is being reshaped we need to treat non-failed devices as
in-sync when we have the data but haven't actually written it out yet.
Reported-by: Adam Kwolek <adam.kwolek@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
commit d70ed2e4fafdbef0800e73942482bb075c21578b
broke hot-add to a linear array.
After that commit, metadata if not written to devices until they
have been fully integrated into the array as determined by
saved_raid_disk. That patch arranged to clear that field after
a recovery completed.
However for linear arrays, there is no recovery - the integration is
instantaneous. So we need to explicitly clear the saved_raid_disk
field.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: Fix usb/isp1760 build on sparc
usb: gadget: epautoconf: do not change number of streams
usb: dwc3: core: fix cached revision on our structure
usb: musb: fix reset issue with full speed device
|
|
* 'upstream-linus' of git://github.com/jgarzik/libata-dev:
pata_of_platform: Add missing CONFIG_OF_IRQ dependency.
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Add a flow_cache_flush_deferred function
ipv4: reintroduce route cache garbage collector
net: have ipconfig not wait if no dev is available
sctp: Do not account for sizeof(struct sk_buff) in estimated rwnd
asix: new device id
davinci-cpdma: fix locking issue in cpdma_chan_stop
sctp: fix incorrect overflow check on autoclose
r8169: fix Config2 MSIEnable bit setting.
llc: llc_cmsg_rcv was getting called after sk_eat_skb.
net: bpf_jit: fix an off-one bug in x86_64 cond jump target
iwlwifi: update SCD BC table for all SCD queues
Revert "Bluetooth: Revert: Fix L2CAP connection establishment"
Bluetooth: Clear RFCOMM session timer when disconnecting last channel
Bluetooth: Prevent uninitialized data access in L2CAP configuration
iwlwifi: allow to switch to HT40 if not associated
iwlwifi: tx_sync only on PAN context
mwifiex: avoid double list_del in command cancel path
ath9k: fix max phy rate at rate control init
nfc: signedness bug in __nci_request()
iwlwifi: do not set the sequence control bit is not needed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Include linux/io.h to jz4740-adc
mfd: Use request_threaded_irq for twl4030-irq instead of irq_set_chained_handler
mfd: Base interrupt for twl4030-irq must be one-shot
mfd: Handle tps65910 clear-mask correctly
mfd: add #ifdef CONFIG_DEBUG_FS guard for ab8500_debug_resources
mfd: Fix twl-core oops while calling twl_i2c_* for unbound driver
mfd: include linux/module.h for ab5500-debugfs
mfd: Update wm8994 active device checks for WM1811
mfd: Set tps6586x bits if new value is different from the old one
mfd: Set da903x bits if new value is different from the old one
mfd: Set adp5520 bits if new value is different from the old one
mfd: Add missed free_irq in da903x_remove
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
* 'for-greg' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: gadget: epautoconf: do not change number of streams
usb: dwc3: core: fix cached revision on our structure
usb: musb: fix reset issue with full speed device
|
|
This commit:
commit 8f5d621543cb064d2989fc223d3c2bc61a43981e
Author: Joachim Foerster <joachim.foerster@missinglinkelectronics.com>
Date: Mon Oct 10 18:06:54 2011 +0200
usb/isp1760: Let OF bindings depend on general CONFIG_OF instead of PPC_OF .
To be able to use the driver on other OF-aware architectures, too.
And add necessary OF related #includes to fix compilation error.
Signed-off-by: Joachim Foerster <joachim.foerster@missinglinkelectronics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
enabled the build on all CONFIG_OF architectures, but it cannot do
this.
This driver depends upon CONFIG_OF_IRQ but not all CONFIG_OF platforms
support that infrastructure, in particular Sparc does not so the
build fails.
Please push a patch like the following to Linus so that this code only
gets built where it actually should.
--------------------
usb/isp1760: Add missing CONFIG_OF_IRQ dependency on OF code.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
* git://git.infradead.org/mtd-2.6:
mtd: plat_ram: call mtd_device_register only if partition data exists
mtd: pxa2xx-flash.c: It used to fall back to provided table.
mtd: gpmi: add missing include 'module.h'
mtd: ndfc: fix typo in structure dereference
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: vub300: fix type of firmware_rom_wait_states module parameter
Revert "mmc: enable runtime PM by default"
mmc: sdhci: remove "state" argument from sdhci_suspend_host
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time/clocksource: Fix kernel-doc warnings
rtc: m41t80: Workaround broken alarm functionality
rtc: Expire alarms after the time is set.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
oprofile: Fix uninitialized memory access when writing to writing to oprofilefs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/for-linus-fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
Revert "xen/pv-on-hvm kexec: add xs_reset_watches to shutdown watches from old kernel"
|
|
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
vmwgfx: Clip cliprects against screen boundaries in present and dirty
vmwgfx: Resend the cursor after legacy modeset
vmwgfx: Do better culling of presents
vmwgfx: Refactor kms code to use vmw_user_lookup_handle helper
vmwgfx: Add helper function to get surface or dmabuf
vmwgfx: Refactor cursor update
vmwgfx: Remove dmabuf check in present ioctl
vmwgfx: Use the revised fifo hw version register when present
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (31 commits)
Revert "[media] af9015: limit I2C access to keep FW happy"
[media] s5p-fimc: Fix camera input configuration in subdev operations
[media] m5mols: Fix logic in sanity check
[media] ati_remote: switch to single-byte scancodes
[media] V4L: mt9m111: fix uninitialised mutex
[media] V4L: omap1_camera: fix missing <linux/module.h> include
[media] V4L: mt9t112: use after free in mt9t112_probe()
[media] V4L: soc-camera: fix compiler warnings on 64-bit platforms
[media] s5p_mfc_enc: fix s/H264/H263/ typo
[media] omap_vout: Fix compile error in 3.1
[media] au0828: add missing models 72101, 72201 & 72261 to the model matrix
[media] au0828: add missing USB ID 2040:7213
[media] au0828: add missing USB ID 2040:7260
[media] [trivial] omap24xxcam-dma: Fix logical test
[media] omap_vout: fix crash if no driver for a display
[media] media: video: s5p-tv: fix build break
[media] omap3isp: fix compilation of ispvideo.c
[media] m5mols: Fix set_fmt to return proper pixel format code
[media] s5p-fimc: Use correct fourcc for RGB565 colour format
[media] s5p-fimc: Fail driver probing when sensor configuration is wrong
...
|
|
If the BMC gets reset, it will return 0x80 response errors.
In less than a week
# grep "Error 80 on cmd 22" /var/log/kernel |wc -l
378681
In this case, it is probably a good idea to restore the IPMI settings.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Arkadiusz Miśkiewicz <a.miskiewicz@gmail.com>
Reported-by: Arkadiusz Miśkiewicz <a.miskiewicz@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Include linux/io.h to fix below build error:
CC drivers/mfd/jz4740-adc.o
drivers/mfd/jz4740-adc.c: In function 'jz4740_adc_irq_demux':
drivers/mfd/jz4740-adc.c:73: error: implicit declaration of function 'readb'
drivers/mfd/jz4740-adc.c: In function 'jz4740_adc_set_enabled':
drivers/mfd/jz4740-adc.c:110: error: implicit declaration of function 'writeb'
drivers/mfd/jz4740-adc.c: In function 'jz4740_adc_set_config':
drivers/mfd/jz4740-adc.c:146: error: implicit declaration of function 'readl'
drivers/mfd/jz4740-adc.c:151: error: implicit declaration of function 'writel'
drivers/mfd/jz4740-adc.c: In function 'jz4740_adc_probe':
drivers/mfd/jz4740-adc.c:249: error: implicit declaration of function 'ioremap_nocache'
drivers/mfd/jz4740-adc.c:249: warning: assignment makes pointer from integer without a cast
drivers/mfd/jz4740-adc.c:289: warning: passing argument 3 of 'mfd_add_devices' discards qualifiers from pointer target type
include/linux/mfd/core.h:93: note: expected 'struct mfd_cell *' but argument is of type 'const struct mfd_cell *'
drivers/mfd/jz4740-adc.c:299: error: implicit declaration of function 'iounmap'
make[2]: *** [drivers/mfd/jz4740-adc.o] Error 1
make[1]: *** [drivers/mfd] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
irq_set_chained_handler sets 'desc->handle_irq'.
However this irq is called by handle_nested_irq from handle_twl4030_pih,
and that uses action->thread_fn.
So the handled set with irq_set_chained_handler is never called.
So change to use request_threaded_irq instead - that sets the correct field.
Tested on GTA04 Phoenux.
Signed-off-by: NeilBrown <neilb@suse.de>
Tested-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
As the interrupt source is only cleared by the threaded interrupt
service routine, we need to make the base interrupt IRQF_ONESHOT.
Without this, the first interrupt from the TWL4030 cause the CPU to
enter an infinite loop trying to handle to interrupt but never
clearing it.
Signed-off-by: NeilBrown <neilb@suse.de>
Tested-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The function is not actually cleaing the bitmask.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
