| Age | Commit message (Collapse) | Author |
|---|
|
If turbo is disabled in the BIOS bit 38 should be set in
MSR_IA32_MISC_ENABLE register per section 14.3.2.1 of the SDM Vol 3
document 325384-050US Feb 2014. If this bit is set do *not* attempt
to disable trubo via the MSR_IA32_PERF_CTL register. On some systems
trying to disable turbo via MSR_IA32_PERF_CTL will cause subsequent
writes to MSR_IA32_PERF_CTL not take affect, in fact reading
MSR_IA32_PERF_CTL will not show the IDA/Turbo DISENGAGE bit(32) as
set. A write of bit 32 to zero returns to normal operation.
Also deal with the case where the processor does not support
turbo and the BIOS does not report the fact in MSR_IA32_MISC_ENABLE
but does report the max and turbo P states as the same value.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=64251
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 21855ff5 (intel_pstate: Set turbo VID for BayTrail) introduced
setting the turbo VID which is required to prevent a machine check on
some Baytrail SKUs under heavy graphics based workloads. The
docmumentation update that brought the requirement to light also
changed the bit mask used for enumerating P state and VID values from
0x7f to 0x3f.
This change returns the mask value to 0x7f.
Tested with the Intel NUC DN2820FYK,
BIOS version FYBYT10H.86A.0034.2014.0513.1413 with v3.16-rc1 and
v3.14.8 kernel versions.
Fixes: 21855ff5 (intel_pstate: Set turbo VID for BayTrail)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=77951
Reported-and-tested-by: Rune Reterson <rune@megahurts.dk>
Reported-and-tested-by: Eric Eickmeyer <erich@ericheickmeyer.com>
Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Revert commit ab0fd674d6ce (ACPI / AC: Remove AC's proc directory.),
because some old tools (e.g. kpowersave from kde 3.5.10) are still
using /proc/acpi/ac_adapter.
Fixes: ab0fd674d6ce (ACPI / AC: Remove AC's proc directory.)
Reported-and-tested-by: Sorin Manolache <sorinm@gmail.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull devicetree bugfix from Grant Likely:
"Important bug fix for parsing 64-bit addresses on 32-bit platforms.
Without this patch the kernel will try to use memory ranges that
cannot be reached"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
of: Check for phys_addr_t overflows in early_init_dt_add_memory_arch
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of 13 fixes, a MAINTAINERS update and a sparse update.
The fixes are mostly correct value initialisations, avoiding NULL
derefs and some uninitialised pointer avoidance.
All the patches have been incubated in -next for a few days. The
final patch (use the scsi data buffer length to extract transfer size)
has been rebased to add a cc to stable, but only the commit message
has changed"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] use the scsi data buffer length to extract transfer size
virtio-scsi: fix various bad behavior on aborted requests
virtio-scsi: avoid cancelling uninitialized work items
ibmvscsi: Add memory barriers for send / receive
ibmvscsi: Abort init sequence during error recovery
qla2xxx: Fix sparse warning in qla_target.c.
bnx2fc: Improve stats update mechanism
bnx2fc: do not scan uninitialized lists in case of error.
fc: ensure scan_work isn't active when freeing fc_rport
pm8001: Fix potential null pointer dereference and memory leak.
MAINTAINERS: Update LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) maintainers Email IDs
be2iscsi: remove potential junk pointer free
be2iscsi: add an missing goto in error path
scsi_error: set DID_TIME_OUT correctly
scsi_error: fix invalid setting of host byte
|
|
Pull drm fixes from Dave Airlie:
"i915, tda998x and vmwgfx fixes,
The main one is i915 fix for missing VGA connectors, along with some
fixes for the tda998x from Russell fixing some modesetting problems.
(still on holidays, but got a spare moment to find these)"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/vmwgfx: Fix incorrect write to read-only register v2:
drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
drm/i915: only apply crt_present check on VLV
drm/i915: Wait for vblank after enabling the primary plane on BDW
drm/i2c: tda998x: add some basic mode validation
drm/i2c: tda998x: faster polling for edid
drm/i2c: tda998x: move drm_i2c_encoder_destroy call
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A few minor fixlets in ARM SoC irq drivers and a fix for a memory leak
which I introduced in the last round of cleanups :("
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix memory leak when calling irq_free_hwirqs()
irqchip: spear_shirq: Fix interrupt offset
irqchip: brcmstb-l2: Level-2 interrupts are edge sensitive
irqchip: armada-370-xp: Mask all interrupts during initialization.
|
|
git://anongit.freedesktop.org/drm-intel
Fixes for 3.16-rc3; most importantly Jesse brings back VGA he took away
on a bunch of machines. Also a vblank fix for BDW and a power workaround
fix for VLV.
* tag 'drm-intel-fixes-2014-07-03' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Drop early VLV WA to fix Voltage not getting dropped to Vmin
drm/i915: only apply crt_present check on VLV
drm/i915: Wait for vblank after enabling the primary plane on BDW
|
|
fix to a 3.15 commit.
* 'vmwgfx-fixes-3.16' of git://people.freedesktop.org/~thomash/linux:
drm/vmwgfx: Fix incorrect write to read-only register v2:
|
|
mode fixes for tda998x.
* 'tda998x-fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox:
drm/i2c: tda998x: add some basic mode validation
drm/i2c: tda998x: faster polling for edid
drm/i2c: tda998x: move drm_i2c_encoder_destroy call
|
|
IIO_CHAN_INFO_SAMP_FREQ and IIO_CHAN_INFO_HYSTERESIS cases ignored
the actual return values (which could be -EINVAL) and instead
returned IIO_VAL_INT_PLUS_MICRO always. Return the actual value
obtained from the functions. Both functions return IIO_VAL_INT_PLUS_MICRO
upon success.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
IIO_CHAN_INFO_SAMP_FREQ and IIO_CHAN_INFO_HYSTERESIS cases ignored
the actual return values (which could be -EINVAL) and instead
returned IIO_VAL_INT_PLUS_MICRO always. Return the actual value
obtained from the functions. Both functions return IIO_VAL_INT_PLUS_MICRO
upon success.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
IIO_CHAN_INFO_SAMP_FREQ and IIO_CHAN_INFO_HYSTERESIS cases ignored
the actual return values (which could be -EINVAL) and instead
returned IIO_VAL_INT_PLUS_MICRO always. Return the actual value
obtained from the functions. Both functions return IIO_VAL_INT_PLUS_MICRO
upon success.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
IIO_CHAN_INFO_SAMP_FREQ and IIO_CHAN_INFO_HYSTERESIS cases ignored
the actual return values (which could be -EINVAL) and instead
returned IIO_VAL_INT_PLUS_MICRO always. Return the actual value
obtained from the functions. Both functions return IIO_VAL_INT_PLUS_MICRO
upon success.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
IIO_CHAN_INFO_SAMP_FREQ and IIO_CHAN_INFO_HYSTERESIS cases ignored
the actual return values (which could be -EINVAL) and instead
returned IIO_VAL_INT_PLUS_MICRO always. Return the actual value
obtained from the functions. Both functions return IIO_VAL_INT_PLUS_MICRO
upon success.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
IIO_CHAN_INFO_SAMP_FREQ and IIO_CHAN_INFO_HYSTERESIS cases ignored
the actual return values (which could be -EINVAL) and instead
returned IIO_VAL_INT_PLUS_MICRO always. Return the actual value
obtained from the functions. Both functions return IIO_VAL_INT_PLUS_MICRO
upon success.
Agreed with by Srinivas.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We are returning success here because PTR_ERR(NULL) is zero. We should
be returning -ENODEV.
Fixes: 3de68d331c24 ('pinctrl: berlin: add the core pinctrl driver for Marvell Berlin SoCs')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch registers the exynos mct clocksource as the current timer
as it has constant clock rate. This will generate correct udelay for
the exynos platform and avoid using unnecessary calibrated
jiffies. This change has been tested on exynos5420 based board and
udelay is very close to expected.
Without this patch udelay() on exynos5400 / exynos5800 is wildly
inaccurate due to big.LITTLE not adjusting loops_per_jiffy correctly.
Also without this patch udelay() on exynos5250 can be innacruate
during transitions between frequencies < 800 MHz (you'll go 200 MHz ->
800 MHz -> 300 MHz and will run at 800 MHz for a time with the wrong
loops_per_jiffy).
[dianders: reworked and created version 3]
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
In (93bfb76 clocksource: exynos_mct: register sched_clock callback) we
supported using the MCT as a scheduler clock. We properly marked
exynos4_read_sched_clock() as notrace. However, we then went and
called another function that _wasn't_ notrace. That means if you do:
cd /sys/kernel/debug/tracing/
echo function_graph > current_tracer
You'll get a crash.
Fix this (but still let other readers of the MCT be trace-enabled) by
adding an extra function. It's important to keep other users of MCT
traceable because the MCT is actually quite slow to access and we want
exynos4_frc_read() to show up in ftrace profiles if it's the
bottleneck.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Pull md bugfixes from Neil Brown:
"Two minor bugfixes for md in 3.16"
* tag 'md/3.16-fixes' of git://neil.brown.name/md:
md: flush writes before starting a recovery.
md: make sure GET_ARRAY_INFO ioctl reports correct "clean" status
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains a few fixes for HD-audio: yet another Dell headset pin
quirk, a fixup for Thinkpad T540P, and an improved fix for
Haswell/Broadwell HDMI clock setup"
* tag 'sound-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - restore BCLK M/N value as per CDCLK for HSW/BDW display HDA controller
drm/i915: provide interface for audio driver to query cdclk
ALSA: hda - Add a fixup for Thinkpad T540p
ALSA: hda - Add another headset pin quirk for some Dell machines
|
|
For Haswell and Broadwell, if the display power well has been disabled,
the display audio controller divider values EM4 M VALUE and EM5 N VALUE
will have been lost. The CDCLK frequency is required for reprogramming them
to generate 24MHz HD-A link BCLK. So provide a private interface for the
audio driver to query CDCLK.
This is a stopgap solution until a more generic interface between audio
and display drivers has been implemented.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB bugfixes from Greg KH:
"Here's a round of USB bugfixes, quirk additions, and new device ids
for 3.16-rc4. Nothing major in here at all, just a bunch of tiny
changes. All have been in linux-next with no reported issues"
* tag 'usb-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: udc: delete td from req's td list at ep_dequeue
usb: Kconfig: make EHCI_MSM selectable for QCOM SOCs
usb-storage/SCSI: Add broken_fua blacklist flag
usb: musb: dsps: fix the base address for accessing the mode register
tools: ffs-test: fix header values endianess
usb: phy: msm: Do not do runtime pm if the phy is not idle
usb: musb: Ensure that cppi41 timer gets armed on premature DMA TX irq
usb: gadget: gr_udc: Fix check for invalid number of microframes
usb: musb: Fix panic upon musb_am335x module removal
usb: gadget: f_fs: resurect usb_functionfs_descs_head structure
Revert "tools: ffs-test: convert to new descriptor format fixing compilation error"
xhci: Fix runtime suspended xhci from blocking system suspend.
xhci: clear root port wake on bits if controller isn't wake-up capable
xhci: correct burst count field for isoc transfers on 1.0 xhci hosts
xhci: Use correct SLOT ID when handling a reset device command
MAINTAINERS: update e-mail address
usb: option: add/modify Olivetti Olicard modems
USB: ftdi_sio: fix null deref at port probe
MAINTAINERS: drop two usb-serial subdriver entries
USB: option: add device ID for SpeedUp SU9800 usb 3g modem
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver bugfixes from Greg KH:
"Nothing major here, just 4 small bugfixes that resolve some issues
reported for the IIO (staging and non-staging) and the tidspbridge
driver"
* tag 'staging-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: tidspbridge: fix an erroneous removal of parentheses
iio: of_iio_channel_get_by_name() returns non-null pointers for error legs
staging: iio/ad7291: fix error code in ad7291_probe()
iio:adc:ad799x: Fix reading and writing of event values, apply shift
|
|
|
|
The module test script for the adm1021 driver exposes a cache problem
when writing temperature limits. temp_min and temp_max are expected
to be stored in milli-degrees C but are stored in degrees C.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Writing to fanX_div does not clear the cache. As a result, reading
from fanX_div may return the old value for up to two seconds
after writing a new value.
This patch ensures the fan_div cache is updated in set_fan_div().
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
temp2_input should not be writable, fix it.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Merge fixes from Andrew Morton:
"14 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
shmem: fix init_page_accessed use to stop !PageLRU bug
kernel/printk/printk.c: revert "printk: enable interrupts before calling console_trylock_for_printk()"
tools/testing/selftests/ipc/msgque.c: improve error handling when not running as root
fs/seq_file: fallback to vmalloc allocation
/proc/stat: convert to single_open_size()
hwpoison: fix the handling path of the victimized page frame that belong to non-LRU
mm:vmscan: update the trace-vmscan-postprocess.pl for event vmscan/mm_vmscan_lru_isolate
msync: fix incorrect fstart calculation
zram: revalidate disk after capacity change
tools: memory-hotplug fix unexpected operator error
tools: cpu-hotplug fix unexpected operator error
autofs4: fix false positive compile error
slub: fix off by one in number of slab tests
mm: page_alloc: fix CMA area initialisation when pageblock > MAX_ORDER
|
|
Alexander reported mkswap on /dev/zram0 is failed if other process is
opening the block device file.
Step is as follows,
0. Reset the unused zram device.
1. Use a program that opens /dev/zram0 with O_RDWR and sleeps
until killed.
2. While that program sleeps, echo the correct value to
/sys/block/zram0/disksize.
3. Verify (e.g. in /proc/partitions) that the disk size is applied
correctly. It is.
4. While that program still sleeps, attempt to mkswap /dev/zram0.
This fails: mkswap: error: swap area needs to be at least 40 KiB
When I investigated, the size get by ioctl(fd, BLKGETSIZE64, xxx) on
mkswap to get a size of blockdev was zero although zram0 has right size by
2.
The reason is zram didn't revalidate disk after changing capacity so that
size of blockdev's inode is not uptodate until all of file is close.
This patch should fix the BUG.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reported-by: Alexander E. Patrakov <patrakov@gmail.com>
Tested-by: Alexander E. Patrakov <patrakov@gmail.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit "drm/vmwgfx: correct fb_fix_screeninfo.line_length", while fixing a
vmwgfx fbdev bug, also writes the pitch to a supposedly read-only register:
SVGA_REG_BYTES_PER_LINE, while it should be (and also in fact is) written to
SVGA_REG_PITCHLOCK.
This patch is Cc'd stable because of the unknown effects writing to this
register might have, particularly on older device versions.
v2: Updated log message.
Cc: stable@vger.kernel.org
Cc: Christopher Friedt <chrisfriedt@gmail.com>
Tested-by: Christopher Friedt <chrisfriedt@gmail.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
|
|
When we write to a degraded array which has a bitmap, we
make sure the relevant bit in the bitmap remains set when
the write completes (so a 're-add' can quickly rebuilt a
temporarily-missing device).
If, immediately after such a write starts, we incorporate a spare,
commence recovery, and skip over the region where the write is
happening (because the 'needs recovery' flag isn't set yet),
then that write will not get to the new device.
Once the recovery finishes the new device will be trusted, but will
have incorrect data, leading to possible corruption.
We cannot set the 'needs recovery' flag when we start the write as we
do not know easily if the write will be "degraded" or not. That
depends on details of the particular raid level and particular write
request.
This patch fixes a corruption issue of long standing and so it
suitable for any -stable kernel. It applied correctly to 3.0 at
least and will minor editing to earlier kernels.
Reported-by: Bill <billstuff2001@sbcglobal.net>
Tested-by: Bill <billstuff2001@sbcglobal.net>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/53A518BB.60709@sbcglobal.net
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If an array has a bitmap, the when we set the "has bitmap" flag we
incorrectly clear the "is clean" flag.
"is clean" isn't really important when a bitmap is present, but it is
best to get it right anyway.
Reported-by: George Duffield <forumscollective@gmail.com>
Link: http://lkml.kernel.org/CAG__1a4MRV6gJL38XLAurtoSiD3rLBTmWpcS5HYvPpSfPR88UQ@mail.gmail.com
Fixes: 36fa30636fb84b209210299684e1be66d9e58217 (v2.6.14)
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
The HDMI PLL input to the tv mux is supposed to be 3, not 2. Fix
the code so that we can properly select the HDMI PLL.
Fixes: 6d00b56fe "clk: qcom: Add support for MSM8960's multimedia clock controller (MMCC)"
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
misc fixes, output fixes for 4k monitor, dpm lockup fixes
* 'drm-fixes-3.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: page table BOs are kernel allocations
drm/radeon/cik: fix typo in EOP packet
drm/radeon: Track the status of a page flip more explicitly
drm/radeon/dpm: fix vddci setup typo on cayman
drm/radeon/dpm: fix typo in vddci setup for eg/btc
drm/radeon: use RADEON_MAX_CRTCS, RADEON_MAX_AFMT_BLOCKS (v2)
drm/radeon: Use only one line for whole DPCD debug output
drm/radeon: add a module parameter to control deep color support
drm/radeon: enable bapm by default on desktop TN/RL boards
drm/radeon: enable bapm by default on KV/KB
drm/radeon: only apply bapm changes for AC power on ARUBA
drm/radeon: adjust default dispclk on DCE6 (v2)
|
|
1539fb9bd405ee32282ea0a38404f9e008ac5b7a managed to somehow +x
drm_drv.c undo it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Userspace shouldn't be able to access them.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Volatile bit was in the wrong location. This bit is
not used at the moment.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tfiga/samsung-clk into clk-fixes-samsung
Samsung clock fixes for v3.16.
This pull request contains fixes for various issues found while testing
-rc versions of Linux 3.16. Mostly two kinds of patches:
* Fixes of incorrectly defined clocks
1) a37c82a clk: samsung: exynos4: Remove SRC_MASK_ISP gates
Issue present since v3.10.
2) 0b1643b clk/exynos5250: fix bit number for tv sysmmu clock
Issue present since v3.16.
3) 44ff025 clk: exynos5420: Remove aclk66_peric from the clock tree description
Issue present since v3.11.
* Adding things missed by original patches
1) cec1cde clk: samsung: fix several typos to fix boot on s3c2410
2) 34ece9e clk: samsung: add more aliases for s3c24xx
Both issues present since the driver was added in v3.16.
3) a92dda4 clk: s3c64xx: Hookup SPI clocks correctly
Issue present since v3.12.
|
|
clk-fixes-ti
|
|
devm_ioremap_resource returns an ERR_PTR value, not NULL, on failure.
A simplified version of the semantic match that finds this problem is as
follows:
// <smpl>
@@
expression e,e1;
statement S;
@@
*e = devm_ioremap_resource(...);
if (!e1) S
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
We need to delete un-finished td from current request's td list
at ep_dequeue API, otherwise, this non-user td will be remained
at td list before this request is freed. So if we do ep_queue->
ep_dequeue->ep_queue sequence, when the complete interrupt for
the second ep_queue comes, we search td list for this request,
the first td (added by the first ep_queue) will be handled, and
its status is still active, so we will consider the this transfer
still not be completed, but in fact, it has completed. It causes
the peripheral side considers it never receives current data for
this transfer.
We met this problem when do "Error Recovery Test - Device Configured"
test item for USBCV2 MSC test, the host has never received ACK for
the IN token for CSW due to peripheral considers it does not get this
CBW, the USBCV test log like belows:
--------------------------------------------------------------------------
INFO
Issuing BOT MSC Reset, reset should always succeed
INFO
Retrieving status on CBW endpoint
INFO
CBW endpoint status = 0x0
INFO
Retrieving status on CSW endpoint
INFO
CSW endpoint status = 0x0
INFO
Issuing required command (Test Unit Ready) to verify device has recovered
INFO
Issuing CBW (attempt #1):
INFO
|----- CBW LUN = 0x0
INFO
|----- CBW Flags = 0x0
INFO
|----- CBW Data Transfer Length = 0x0
INFO
|----- CBW CDB Length = 0x6
INFO
|----- CBW CDB-00 = 0x0
INFO
|----- CBW CDB-01 = 0x0
INFO
|----- CBW CDB-02 = 0x0
INFO
|----- CBW CDB-03 = 0x0
INFO
|----- CBW CDB-04 = 0x0
INFO
|----- CBW CDB-05 = 0x0
INFO
Issuing CSW : try 1
INFO
CSW Bulk Request timed out!
ERROR
Failed CSW phase : should have been success or stall
FAIL
(5.3.4) The CSW status value must be 0x00, 0x01, or 0x02.
ERROR
BOTCommonMSCRequest failed: error=80004000
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After unbinding the driver memory was corrupted by double free of
clk_lookup structure. This lead to OOPS when re-binding the driver
again.
The driver allocated memory for 'clk_lookup' with devm_kzalloc. During
driver removal this memory was freed twice: once by clkdev_drop() and
second by devm code.
Kernel panic log:
[ 30.839284] Unable to handle kernel paging request at virtual address 5f343173
[ 30.846476] pgd = dee14000
[ 30.849165] [5f343173] *pgd=00000000
[ 30.852703] Internal error: Oops: 805 [#1] PREEMPT SMP ARM
[ 30.858166] Modules linked in:
[ 30.861208] CPU: 0 PID: 1 Comm: bash Not tainted 3.16.0-rc2-00239-g94bdf617b07e-dirty #40
[ 30.869364] task: df478000 ti: df480000 task.ti: df480000
[ 30.874752] PC is at clkdev_add+0x2c/0x38
[ 30.878738] LR is at clkdev_add+0x18/0x38
[ 30.882732] pc : [<c0350908>] lr : [<c03508f4>] psr: 60000013
[ 30.882732] sp : df481e78 ip : 00000001 fp : c0700ed8
[ 30.894187] r10: 0000000c r9 : 00000000 r8 : c07b0e3c
[ 30.899396] r7 : 00000002 r6 : df45f9d0 r5 : df421390 r4 : c0700d6c
[ 30.905906] r3 : 5f343173 r2 : c0700d84 r1 : 60000013 r0 : c0700d6c
[ 30.912417] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 30.919534] Control: 10c53c7d Table: 5ee1406a DAC: 00000015
[ 30.925262] Process bash (pid: 1, stack limit = 0xdf480240)
[ 30.930817] Stack: (0xdf481e78 to 0xdf482000)
[ 30.935159] 1e60: 00001000 df6de610
[ 30.943321] 1e80: df7f4558 c0355650 c05ec6ec c0700eb0 df6de600 df7f4510 dec9d69c 00000014
[ 30.951480] 1ea0: 00167b48 df6de610 c0700e30 c0713518 00000000 c0700e30 dec9d69c 00000006
[ 30.959639] 1ec0: 00167b48 c02c1b7c c02c1b64 df6de610 c07aff48 c02c0420 c06fb150 c047cc20
[ 30.967798] 1ee0: df6de610 df6de610 c0700e30 df6de644 c06fb150 0000000c dec9d690 c02bef90
[ 30.975957] 1f00: dec9c6c0 dece4c00 df481f80 dece4c00 0000000c c02be73c 0000000c c016ca8c
[ 30.984116] 1f20: c016ca48 00000000 00000000 c016c1f4 00000000 00000000 b6f18000 df481f80
[ 30.992276] 1f40: df7f66c0 0000000c df480000 df480000 b6f18000 c011094c df47839c 60000013
[ 31.000435] 1f60: 00000000 00000000 df7f66c0 df7f66c0 0000000c df480000 b6f18000 c0110dd4
[ 31.008594] 1f80: 00000000 00000000 0000000c b6ec05d8 0000000c b6f18000 00000004 c000f2a8
[ 31.016753] 1fa0: 00001000 c000f0e0 b6ec05d8 0000000c 00000001 b6f18000 0000000c 00000000
[ 31.024912] 1fc0: b6ec05d8 0000000c b6f18000 00000004 0000000c 00000001 00000000 00167b48
[ 31.033071] 1fe0: 00000000 bed83a80 b6e004f0 b6e5122c 60000010 00000001 ffffffff ffffffff
[ 31.041248] [<c0350908>] (clkdev_add) from [<c0355650>] (s2mps11_clk_probe+0x2b4/0x3b4)
[ 31.049223] [<c0355650>] (s2mps11_clk_probe) from [<c02c1b7c>] (platform_drv_probe+0x18/0x48)
[ 31.057728] [<c02c1b7c>] (platform_drv_probe) from [<c02c0420>] (driver_probe_device+0x13c/0x384)
[ 31.066579] [<c02c0420>] (driver_probe_device) from [<c02bef90>] (bind_store+0x88/0xd8)
[ 31.074564] [<c02bef90>] (bind_store) from [<c02be73c>] (drv_attr_store+0x20/0x2c)
[ 31.082118] [<c02be73c>] (drv_attr_store) from [<c016ca8c>] (sysfs_kf_write+0x44/0x48)
[ 31.090016] [<c016ca8c>] (sysfs_kf_write) from [<c016c1f4>] (kernfs_fop_write+0xc0/0x17c)
[ 31.098176] [<c016c1f4>] (kernfs_fop_write) from [<c011094c>] (vfs_write+0xa0/0x1c4)
[ 31.105899] [<c011094c>] (vfs_write) from [<c0110dd4>] (SyS_write+0x40/0x8c)
[ 31.112931] [<c0110dd4>] (SyS_write) from [<c000f0e0>] (ret_fast_syscall+0x0/0x3c)
[ 31.120481] Code: e2842018 e584501c e1a00004 e885000c (e5835000)
[ 31.126596] ---[ end trace efad45bfa3a61b05 ]---
[ 31.131181] Kernel panic - not syncing: Fatal exception
[ 31.136368] CPU1: stopping
[ 31.139054] CPU: 1 PID: 0 Comm: swapper/1 Tainted: G D 3.16.0-rc2-00239-g94bdf617b07e-dirty #40
[ 31.148697] [<c0016480>] (unwind_backtrace) from [<c0012950>] (show_stack+0x10/0x14)
[ 31.156419] [<c0012950>] (show_stack) from [<c0480db8>] (dump_stack+0x80/0xcc)
[ 31.163622] [<c0480db8>] (dump_stack) from [<c001499c>] (handle_IPI+0x130/0x15c)
[ 31.170998] [<c001499c>] (handle_IPI) from [<c000862c>] (gic_handle_irq+0x60/0x68)
[ 31.178549] [<c000862c>] (gic_handle_irq) from [<c0013480>] (__irq_svc+0x40/0x70)
[ 31.186009] Exception stack(0xdf4bdf88 to 0xdf4bdfd0)
[ 31.191046] df80: ffffffed 00000000 00000000 00000000 df4bc000 c06d042c
[ 31.199207] dfa0: 00000000 ffffffed c06d03c0 00000000 c070c288 00000000 00000000 df4bdfd0
[ 31.207363] dfc0: c0010324 c0010328 60000013 ffffffff
[ 31.212402] [<c0013480>] (__irq_svc) from [<c0010328>] (arch_cpu_idle+0x28/0x30)
[ 31.219783] [<c0010328>] (arch_cpu_idle) from [<c005f150>] (cpu_startup_entry+0x2c4/0x3f0)
[ 31.228027] [<c005f150>] (cpu_startup_entry) from [<400086c4>] (0x400086c4)
[ 31.234968] ---[ end Kernel panic - not syncing: Fatal exception
Fixes: 7cc560dea415 ("clk: s2mps11: Add support for s2mps11")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Define ti_clk_register_dpll_x2() and of_ti_am3_dpll_x2_setup() if
AM43XX is defined.
Fixes the below boot issue.
[ 2.157258] gpmc_l3_clk not enabled
[ 2.161194] gpmc_l3_clk not enabled
[ 2.164896] Division by zero in kernel.
[ 2.169055] CPU: 0 PID: 321 Comm: kworker/u2:2 Tainted: G W 3.16.0-rc1-00008-g4c0e520 #273
[ 2.178880] Workqueue: deferwq deferred_probe_work_func
[ 2.184459] [<c001477c>] (unwind_backtrace) from [<c001187c>] (show_stack+0x10/0x14)
[ 2.192752] [<c001187c>] (show_stack) from [<c0530f28>] (dump_stack+0x80/0x9c)
[ 2.200486] [<c0530f28>] (dump_stack) from [<c02c867c>] (Ldiv0+0x8/0x10)
[ 2.207678] [<c02c867c>] (Ldiv0) from [<c0022da0>] (gpmc_calc_divider+0x24/0x40)
[ 2.215490] [<c0022da0>] (gpmc_calc_divider) from [<c0022e20>] (gpmc_cs_set_timings+0x18/0x474)
[ 2.224783] [<c0022e20>] (gpmc_cs_set_timings) from [<c003069c>] (gpmc_nand_init+0x74/0x1a8)
[ 2.233791] [<c003069c>] (gpmc_nand_init) from [<c0024668>] (gpmc_probe+0x52c/0x874)
[ 2.242089] [<c0024668>] (gpmc_probe) from [<c0349218>] (platform_drv_probe+0x18/0x48)
[ 2.250534] [<c0349218>] (platform_drv_probe) from [<c0347d88>] (driver_probe_device+0x104/0x22c)
[ 2.259988] [<c0347d88>] (driver_probe_device) from [<c03464dc>] (bus_for_each_drv+0x44/0x8c)
[ 2.269087] [<c03464dc>] (bus_for_each_drv) from [<c0347c4c>] (device_attach+0x74/0x8c)
[ 2.277620] [<c0347c4c>] (device_attach) from [<c0347380>] (bus_probe_device+0x88/0xb0)
[ 2.286074] [<c0347380>] (bus_probe_device) from [<c0347768>] (deferred_probe_work_func+0x60/0x90)
[ 2.295611] [<c0347768>] (deferred_probe_work_func) from [<c004ef50>] (process_one_work+0x1b4/0x4bc)
[ 2.305288] [<c004ef50>] (process_one_work) from [<c004f3d4>] (worker_thread+0x148/0x550)
[ 2.313954] [<c004f3d4>] (worker_thread) from [<c0055a48>] (kthread+0xc8/0xe4)
[ 2.321628] [<c0055a48>] (kthread) from [<c000e648>] (ret_from_fork+0x14/0x2c)
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev fixes from Tomi Valkeinen:
"A few minor fbdev fixes for bfin_adv7393fb, omapdss, vt8500lcdfb,
atmel_lcdfb"
* tag 'fbdev-fixes-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
fb: adv7393: add missing semicolon
video: omapdss: Fix potential null pointer dereference
video: vt8500lcdfb: Remove kfree call since devm_kzalloc() is used
drivers:video:fbdev atmel_lcdfb.c power GPIO registration bug
|
|
This prevents a panic: radeon_crtc_handle_page_flip() could run before
radeon_flip_work_func(), triggering the BUG_ON() in drm_vblank_put().
Tested-by: Dieter Nützel <Dieter@nuetzel-hh.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We were using the vddc mask rather than the vddci mask.
Bug:
https://bugzilla.kernel.org/show_bug.cgi?id=79071
May also fix:
https://bugs.freedesktop.org/show_bug.cgi?id=69723
Noticed by: Dieter Nützel <Dieter@nuetzel-hh.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
We were using the vddc mask rather than the vddci mask.
Bug:
https://bugzilla.kernel.org/show_bug.cgi?id=79071
Possibly also fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=68571
Noticed-by: Jonathan Howard <jonathan@unbiased.name>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
v2: agd5f: compile fix
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
