| Age | Commit message (Collapse) | Author |
|---|
|
The default maximum transmit length for NCM USB frames should be so
that a short packet happens at the end if the device supports a length
greater than the defined maximum. This is achieved by adding 4 bytes
to the maximum length so that the existing logic can fit a short
packet there.
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/romieu/netdev-2.6
|
|
The firmware is cached during the first successfull call to open() and
released once the network device is unregistered. The driver uses the
cached firmware between open() and unregister_netdev().
So far the firmware is optional : a failure to load the firmware does
not prevent open() to success. It is thus necessary to 1) unregister
all 816x / 810[23] devices and 2) force a driver probe to issue a new
firmware load.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Fixed-by: Ciprian Docan <docan@eden.rutgers.edu>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
|
|
Fixed packets parameters for FW in UDP checksum offload flow.
Do not dereference TCP headers on non TCP frames.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A deadlock was reported to me recently that occured when netconsole was being
used in a virtual guest. If the virtio_net driver was removed while netconsole
was setup to use an interface that was driven by that driver, the guest
deadlocked. No backtrace was provided because netconsole was the only console
configured, but it became clear pretty quickly what the problem was. In
netconsole_netdev_event, if we get an unregister event, we call
__netpoll_cleanup with the target_list_lock held and irqs disabled.
__netpoll_cleanup can, if pending netpoll packets are waiting call
cancel_delayed_work_sync, which is a sleeping path. the might_sleep call in
that path gets triggered, causing a console warning to be issued. The
netconsole write handler of course tries to take the target_list_lock again,
which we already hold, causing deadlock.
The fix is pretty striaghtforward. Simply drop the target_list_lock and
re-enable irqs prior to calling __netpoll_cleanup, the re-acquire the lock, and
restart the loop. Confirmed by myself to fix the problem reported.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
The mechanism used to initiate work events from the interrupt
handler has a classic read/modify/write race between the interrupt
handler that sets the condition, and the worker task that reads and
clears the condition. Close these races by using atomic
bit fields.
Cc: stable@kernel.org
Cc: Jie Yang <jie.yang@atheros.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 609ff3b ("be2net: add code to display temperature of ASIC")
adds support to display temperature of ASIC but there is missing
increment of work_counter in be_worker. Because of this 1) the
function be_cmd_get_die_temperature is called every 1 second instead
of every 32 seconds 2) be_cmd_get_die_temperature is called, although
it is not supported. This patch fixes this bug.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mac-fec.c was setting individual UDP address registers instead of multicast
group address registers when joining a multicast group.
This prevented from correctly receiving UDP multicast packets.
According to datasheet, replaced hash_table_high and hash_table_low
with grp_hash_table_high and grp_hash_table_low respectively.
Also renamed hash_table_* with grp_hash_table_* in struct fec declaration
for 8xx: these registers are used only for multicast there.
Tested on a MPC5121 based board.
Build tested also against mpc866_ads_defconfig.
Signed-off-by: Andrea Galbusera <gizero@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since
commit a120e912eb51e347f36c71b60a1d13af74d30e83
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Fri Feb 19 15:47:33 2010 -0800
iwlwifi: sanity check before counting number of tfds can be free
we use skb->data after calling ieee80211_tx_status_irqsafe(), which
could free skb instantly.
On current kernels I do not observe practical problems related with
bug, but on 2.6.35.y it cause random system hangs when stressing
wireless link, making bisection of other problems impossible.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since
commit a120e912eb51e347f36c71b60a1d13af74d30e83
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Fri Feb 19 15:47:33 2010 -0800
iwlwifi: sanity check before counting number of tfds can be free
we use skb->data after calling ieee80211_tx_status_irqsafe(), which
could free skb instantly.
On current kernels I do not observe practical problems related with
bug, but on 2.6.35.y it cause random system hangs when stressing
wireless link.
Cc: stable@kernel.org # 2.6.32+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The slave member of struct aggregator does not necessarily point
to a slave which is part of the aggregator. It points to the
slave structure containing the aggregator structure, while
completely different slaves (or no slaves at all) may be part of
the aggregator.
The agg_device_up() function wrongly uses agg->slave to find the state
of the aggregator. Use agg->lag_ports->slave instead. The bug has
been introduced by commit 4cd6fe1c6483cde93e2ec91f58b7af9c9eea51ad
("bonding: fix link down handling in 802.3ad mode").
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are currently continuing if ehea_restart_qps() fails, when we
do a memory DLPAR (remove or add more memory to the system).
This patch just let the NAPI disabled if the ehea_restart_qps()
fails.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch 'ath9k_hw: fix stopping rx DMA during resets' added code to detect
a condition where rx DMA was stopped, but the MAC failed to enter the idle
state. This condition requires a hardware reset, however the return value
of ath_stoprecv was 'true' in that case, which allowed it to skip the reset
when issuing a fast channel change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Paul Stewart <pstew@google.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
For some reason, sending QoS configuration causes transmission to stop
after a single frame on HT channels when not associated. Removing the
extra QoS configuration has no effect on station mode, and fixes
injection mode.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
Several tests in the ipv6 routing code check IFF_LOOPBACK, and
allowing stacking such as VLAN'ing on top of loopback results in a
netdevice which reports IFF_LOOPBACK but really isn't the loopback
device.
Instead of spamming the ipv6 routing code with even more special tests,
simply disallow VLAN over loopback.
The result of this patch is:
# modprobe 8021q
# vconfig add lo 43
ERROR: trying to add VLAN #43 to IF -:lo:- error: Operation not supported
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes port identification on optic devices when there's no link on the port.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The memory leak was caused by unintentional assignment of the Rx path
destroy callback function pointer to NULL just after correct
initialization.
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During a kernel crash, bna control path state machine and firmware do not
get a notification and hence are not cleanly shutdown. The registers
holding driver/IOC state information are not reset back to valid
disabled/parking values. This causes subsequent driver initialization
to hang during kdump kernel boot. This patch, during the initialization
of first PCI function, resets corresponding register when unclean shutown
is detect by reading chip registers. This will make sure that ioc/fw
gets clean re-initialization.
Signed-off-by: Debashis Dutt <ddutt@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
priv->tx_power_next is not initialized to max supported power,
but instead default value is used, what cause errors like
[ 58.597834] iwl3945 0000:03:00.0: Requested user TXPOWER 15 above upper limit 14.
[ 58.597839] iwl3945 0000:03:00.0: Error setting Tx power (-22).
if maximum tx power read from the eeprom is smaller than default.
In consequence card is unable to initialize properly. Fix the problem
and cleanup tx power initialization.
Reported-and-tested-by: Robin Dong <hao.bigrat@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Cc: stable@kernel.org
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 74888760d40b3ac9054f9c5fa07b566c0676ba2d
"dt/net: Eliminate users of of_platform_{,un}register_driver"
broke building mscan driver. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bwh/sfc-2.6
|
|
Enabling write-combining may also enable read reordering. The BIU is
only guaranteed to read from a 128-bit CSR or 64-bit SRAM word when
the host reads from its lowest address; otherwise the BIU may use the
latched value. Therefore we need to reinstate the read memory
barriers after the first read operation for each CSR or SRAM word.
Signed-off-by; Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a skb is delivered to a registered callback, cn_call_callback()
incorrectly returns -ENODEV after freeing the skb, causing cn_rx_skb()
to free the skb a second time.
Reported-by: Eric B Munson <emunson@mgebm.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass the correct module name and device interface so that
ethtool can display the proper values.
The firmware version will be fixed later on when the FW
can actually report a version. :)
Reported-by: Richard Farina <sidhayn@gmail.com>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Tested-by: Richard Farina <sidhayn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
During PHY errors, the MAC can sometimes fail to enter an idle state on older
hardware (before AR9380) after an rx stop has been requested.
This typically shows up in the kernel log with messages like these:
ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:504 ath_stoprecv+0xcc/0xf0 [ath9k]()
Call Trace:
[<8023f0e8>] dump_stack+0x8/0x34
[<80075050>] warn_slowpath_common+0x78/0xa4
[<80075094>] warn_slowpath_null+0x18/0x24
[<80d66d60>] ath_stoprecv+0xcc/0xf0 [ath9k]
[<80d642cc>] ath_set_channel+0xbc/0x270 [ath9k]
[<80d65254>] ath_radio_disable+0x4a4/0x7fc [ath9k]
When this happens, the state that the MAC enters is easy to identify and
does not result in bogus DMA traffic, however to ensure a working state
after a channel change, the hardware should still be reset.
This patch adds detection for this specific MAC state, after which the above
warnings completely disappear in my tests.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Cc: Kyungwan Nam <Kyungwan.Nam@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
During self-tests we use efx_process_channel_now() to handle
completion and other events synchronously. This disables interrupts
and NAPI processing for the channel in question, but it may still be
interrupted by another channel. A single socket may receive packets
from multiple net devices or even multiple channels of the same net
device, so this can result in deadlock on a socket lock.
Receiving packets in process context will also result in incorrect
classification by the network cgroup classifier.
Therefore, we must only use efx_process_channel_now() in the offline
loopback tests (which never deliver packets up the stack) and not for
the online interrupt and event tests.
For the interrupt test, there is no reason to process events. We
only care that an interrupt is raised.
For the event test, we want to know whether events have been received,
and there may be many events ahead of the one we inject. Therefore
remove efx_channel::magic_count and instead test whether
efx_channel::eventq_read_ptr advances. This is currently an event
queue index and might wrap around to exactly the same value, resulting
in a false negative. Therefore move the masking to efx_event() and
efx_nic_eventq_read_ack() so that it cannot wrap within the time of
the test.
The event test also tries to diagnose failures by checking whether an
event was delivered without causing an interrupt. Add and use a
helper function that only does this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
If the TX queues are running during loopback self tests, host
traffic gets looped back which causes the test to fail. Avoid
restarting the TX queues after the port reset so that any packets
sent by the host get held back until after the tests have completed.
[bwh: Also wake all TX queues at the end of self-tests.]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Cc: stable@kernel.org
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
replace relpy with reply.
replace premanent with permanent.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
replace tranmitted with transmitted.
replace tranmitting with transmitting.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now, alb_bond_info uses rx_ntt,rlb_update_delay_counter and
rlb_update_retry_counter to decide when to call rlb_update_rx_clients().
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now bonding-alb uses delayed_work instead of timer_list.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is unnecessary to set save_load to 1 here,
as the tx_hashtbl is just kzalloced.
Signed-off-by: Weiping Pan(潘卫平) <panweiping3@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some old MAC chips without COE sometime the
Transmit Underflow error is issued.
The driver aborted all the transmission process
and initialized it from scratch.
This breaks the network activity as raised by Nachiketa
on a SPEAr board.
The patch is to fix this rare underflow event.
The driver will only clear the interrupt and the Tx
DMA will go out the Suspend state as soon as the
descriptor is fetched again.
The driver will continue to bump-up the DMA FIFO threshold
that, indeed, helped somebody to prevent this kind of error
in the past as well.
Reported-by: Nachiketa Prachanda <nprachanda@ncomputing.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reviews the open function and fixes some
errors when exit with an error state.
It also moves the request_irq after core is initialized
when interrupts are properly masked.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a compilation error when build the
dwmac_lib with the DEBUG option enabled.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Otherwise, IWLWIFI_LEGACY has to be selected independently before the
drivers are made available.
Reported-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
|
|
In commit 13583b16592a ("PCI: refactor io size calculation code") Ram
had a thinko in the refactorization of the code: the end result used the
variable 'align' for the bus alignment, but the original code used
'min_align'.
Since then, another use of that 'align' variable got introduced by
commit c8adf9a3e873 ("PCI: pre-allocate additional resources to devices
only after successful allocation of essential resources.")
Fix both of those uses to use 'min_align' as they should.
Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Ram Pai <linuxram@us.ibm.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net: Add support for SMSC LAN9530, LAN9730 and LAN89530
mlx4_en: Restoring RX buffer pointer in case of failure
mlx4: Sensing link type at device initialization
ipv4: Fix "Set rt->rt_iif more sanely on output routes."
MAINTAINERS: add entry for Xen network backend
be2net: Fix suspend/resume operation
be2net: Rename some struct members for clarity
pppoe: drop PPPOX_ZOMBIEs in pppoe_flush_dev
dsa/mv88e6131: add support for mv88e6085 switch
ipv6: Enable RFS sk_rxhash tracking for ipv6 sockets (v2)
be2net: Fix a potential crash during shutdown.
bna: Fix for handling firmware heartbeat failure
can: mcp251x: Allow pass IRQ flags through platform data.
smsc911x: fix mac_lock acquision before calling smsc911x_mac_read
iwlwifi: accept EEPROM version 0x423 for iwl6000
rt2x00: fix cancelling uninitialized work
rtlwifi: Fix some warnings/bugs
p54usb: IDs for two new devices
wl12xx: fix potential buffer overflow in testmode nvs push
zd1211rw: reset rx idle timer from tasklet
...
|
|
This patch adds support for SMSC's LAN9530, LAN9730 and LAN89530 USB
ethernet controllers to the existing smsc95xx driver by adding
their new USB VID/PID pairs.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.infradead.org/mtd-2.6:
mtd: atmel_nand: use CPU I/O when buffer is in vmalloc(ed) region
mtd: atmel_nand: modify test case for using DMA operations
mtd: atmel_nand: fix support for CPUs that do not support DMA access
mtd: atmel_nand: trivial: change DMA usage information trace
mtd: mtdswap: fix printk format warning
|
|
This patch fixes a very serious off-by-one bug in
the driver, which could leave the device in an
unresponsive state.
The problem was that the extra_len variable [used to
reserve extra scratch buffer space for the firmware]
was left uninitialized. Because p54_assign_address
later needs the value to reserve additional space,
the resulting frame could be to big for the small
device's memory window and everything would
immediately come to a grinding halt.
Reference: https://bugs.launchpad.net/bugs/722185
Cc: <stable@kernel.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Jason Conti <jason.conti@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
These missing chip wakeups mainly cause crashes on AR5416 cards in MIPS
boards, but have also been reported to cause radio stability issues on
AR9285.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] compile fix for latest binutils
[S390] cio: prevent purging of CCW devices in the online state
[S390] qdio: fix init sequence
[S390] Fix parameter passing for smp_switch_to_cpu()
[S390] oprofile s390: prevent stack corruption
|
