Age | Commit message (Collapse) | Author |
|
[ Upstream commit a13c06525ab9ff442924e67df9393a5efa914c56 ]
When an Marvell 88E1512 PHY is connected to a nic in SGMII mode, the
fiber page is used for the SGMII host-side connection. The PHY driver
notices that SUPPORTED_FIBRE is set, so it tries reading the fiber page
for the link status, and ends up reading the MAC-side status instead of
the outgoing (copper) link. This leads to incorrect results reported
via ethtool.
If the PHY is connected via SGMII to the host, ignore the fiber page.
However, continue to allow the existing power management code to
suspend and resume the fiber page.
Fixes: 6cfb3bcc0641 ("Marvell phy: check link status in case of fiber link.")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 17fab473693e8357a9aa6fee4fbed6c13a34bd81 ]
There are two bits in the PADCFG0 register to configure direction, one per
TX/RX buffers.
For now we wrongly assume that the GPIO is always requested before it is being
used, which is not true when the GPIO is used through irqchip. In this case the
GPIO is never requested and we never enable RX buffer for it.
Fix this by setting both bits accordingly.
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3546fb0cdac25a79c89d87020566fab52b92867d ]
After rollover of the IOVA space, we want to get a low IOVA address,
otherwise the the games we play by remembering the last IOVA are
pointless. When we search for a free hole with DRM_MM_SEARCH_DEFAULT,
drm_mm will pop the next entry from the free holes stack, which will
likely be a high IOVA. By using DRM_MM_SEARCH_BELOW we can trick
drm_mm into reversing the search and provide us with a low IOVA.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Wladimir van der Laan <laanwj@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 23d28a859fb847fd7fcfbd31acb3b160abb5d6ae ]
When using the ibmveth driver in a KVM/QEMU based VM, it currently
always prints out a scary error message like this when it is started:
ibmveth 71000003 (unregistered net_device): unable to change
checksum offload settings. 1 rc=-2 ret_attr=71000003
This happens because the driver always tries to enable the checksum
offloading without checking for the availability of this feature first.
QEMU does not support checksum offloading for the spapr-vlan device,
thus we always get the error message here.
According to the LoPAPR specification, the "ibm,illan-options" property
of the corresponding device tree node should be checked first to see
whether the H_ILLAN_ATTRIUBTES hypercall and thus the checksum offloading
feature is available. Thus let's do this in the ibmveth driver, too, so
that the error message is really only limited to cases where something
goes wrong, and does not occur if the feature is just missing.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit efb5f68f32995c146944a9d4257c3cf8eae2c4a1 ]
Mac aging is applicable only for dynamically learnt remote mac
entries. Check for user configured static remote mac entries
and skip aging.
Signed-off-by: Balakrishnan Raman <ramanb@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d0fa28f00052391b5df328f502fbbdd4444938b7 ]
I don't have any guests with PAGE_SIZE > 64k but the
code seems to be clearly broken in that case
as PAGE_SIZE / MERGEABLE_BUFFER_ALIGN will need
more than 8 bit and so the code in mergeable_ctx_to_buf_address
does not give us the actual true size.
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a59b7e0246774e28193126fe7fdbbd0ae9c67dcc ]
mlxsw_sp_nexthop_group_mac_update() is called in one of two cases:
1) When the MAC of a nexthop needs to be updated
2) When the size of a nexthop group has changed
In the second case the adjacency entries for the nexthop group need to
be reallocated from the adjacency table. In this case we must write to
the entries the MAC addresses of all the nexthops that should be
offloaded and not only those whose MAC changed. Otherwise, these entries
would be filled with garbage data, resulting in packet loss.
Fixes: a7ff87acd995 ("mlxsw: spectrum_router: Implement next-hop routing")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit bd00fdf198e2da475a2f4265a83686ab42d998a8 ]
The recently added mediated VFIO driver doesn't know about powerpc iommu.
It thus doesn't register a struct iommu_table_group in the iommu group
upon device creation. The iommu_data pointer hence remains null.
This causes a kernel oops when userspace tries to set the iommu type of a
container associated with a mediated device to VFIO_SPAPR_TCE_v2_IOMMU.
[ 82.585440] mtty mtty: MDEV: Registered
[ 87.655522] iommu: Adding device 83b8f4f2-509f-382f-3c1e-e6bfe0fa1001 to group 10
[ 87.655527] vfio_mdev 83b8f4f2-509f-382f-3c1e-e6bfe0fa1001: MDEV: group_id = 10
[ 116.297184] Unable to handle kernel paging request for data at address 0x00000030
[ 116.297389] Faulting instruction address: 0xd000000007870524
[ 116.297465] Oops: Kernel access of bad area, sig: 11 [#1]
[ 116.297611] SMP NR_CPUS=2048
[ 116.297611] NUMA
[ 116.297627] PowerNV
...
[ 116.297954] CPU: 33 PID: 7067 Comm: qemu-system-ppc Not tainted 4.10.0-rc5-mdev-test #8
[ 116.297993] task: c000000e7718b680 task.stack: c000000e77214000
[ 116.298025] NIP: d000000007870524 LR: d000000007870518 CTR: 0000000000000000
[ 116.298064] REGS: c000000e77217990 TRAP: 0300 Not tainted (4.10.0-rc5-mdev-test)
[ 116.298103] MSR: 9000000000009033 <SF,HV,EE,ME,IR,DR,RI,LE>
[ 116.298107] CR: 84004444 XER: 00000000
[ 116.298154] CFAR: c00000000000888c DAR: 0000000000000030 DSISR: 40000000 SOFTE: 1
GPR00: d000000007870518 c000000e77217c10 d00000000787b0ed c000000eed2103c0
GPR04: 0000000000000000 0000000000000000 c000000eed2103e0 0000000f24320000
GPR08: 0000000000000104 0000000000000001 0000000000000000 d0000000078729b0
GPR12: c00000000025b7e0 c00000000fe08400 0000000000000001 000001002d31d100
GPR16: 000001002c22c850 00003ffff315c750 0000000043145680 0000000043141bc0
GPR20: ffffffffffffffed fffffffffffff000 0000000020003b65 d000000007706018
GPR24: c000000f16cf0d98 d000000007706000 c000000003f42980 c000000003f42980
GPR28: c000000f1575ac00 c000000003f429c8 0000000000000000 c000000eed2103c0
[ 116.298504] NIP [d000000007870524] tce_iommu_attach_group+0x10c/0x360 [vfio_iommu_spapr_tce]
[ 116.298555] LR [d000000007870518] tce_iommu_attach_group+0x100/0x360 [vfio_iommu_spapr_tce]
[ 116.298601] Call Trace:
[ 116.298610] [c000000e77217c10] [d000000007870518] tce_iommu_attach_group+0x100/0x360 [vfio_iommu_spapr_tce] (unreliable)
[ 116.298671] [c000000e77217cb0] [d0000000077033a0] vfio_fops_unl_ioctl+0x278/0x3e0 [vfio]
[ 116.298713] [c000000e77217d40] [c0000000002a3ebc] do_vfs_ioctl+0xcc/0x8b0
[ 116.298745] [c000000e77217de0] [c0000000002a4700] SyS_ioctl+0x60/0xc0
[ 116.298782] [c000000e77217e30] [c00000000000b220] system_call+0x38/0xfc
[ 116.298812] Instruction dump:
[ 116.298828] 7d3f4b78 409effc8 3d220000 e9298020 3c800140 38a00018 608480c0 e8690028
[ 116.298869] 4800249d e8410018 7c7f1b79 41820230 <e93e0030> 2fa90000 419e0114 e9090020
[ 116.298914] ---[ end trace 1e10b0ced08b9120 ]---
This patch fixes the oops.
Reported-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c5f21c9f878b8dcd54d0b9739c025ca73cb4c091 ]
Return success when the ring is properly initialized, otherwise return
failure.
Tonga SRIOV VF doesn't have UVD and VCE engines, the initialization of
these IPs is bypassed. The system crashes if application submit IB to
their rings which are not ready to use. It could be a common issue if
IP having ring buffer is disabled for some reason on specific ASIC, so
it should check the ring being ready to use.
Bug: amdgpu_test crashes system on Tonga VF.
Signed-off-by: Ding Pixel <Pixel.Ding@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 738f7f647371ff4cfc9646c99dba5b58ad142db3 ]
The xgbe_init() routine returns a return code indicating success or
failure, but the return code is not checked. Add code to xgbe_init()
to issue a message when failures are seen and add code to check the
xgbe_init() return code.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit cfee5d63767b2e7997c1f36420d008abbe61565c ]
On Ideapad laptops, ACPI event 1 is currently not handled. Many models
log "ideapad_laptop: Unknown event: 1" every 20 seconds or so while
running on battery power. Some convertible laptops receive this event
when switching in and out of tablet mode.
This adds and additional case for event 1 in ideapad_acpi_notify to call
ideapad_input_report(priv, vpc_bit), so that the event is reported to
userspace and we avoid unnecessary logging.
Fixes bug #107481 (https://bugzilla.kernel.org/show_bug.cgi?id=107481)
Fixes bug #65751 (https://bugzilla.kernel.org/show_bug.cgi?id=65751)
Signed-off-by: Zach Ploskey <zach@ploskey.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 92549cdc288f47f3a98cf80ac5890c91f5876a06 ]
A recent firmware change seems to have enabled thermal zones on the
iwlwifi driver. Unfortunately, my device fails when registering the
thermal zone. This doesn't stop the driver from attempting to unregister
the thermal zone at unload time, triggering a NULL pointer deference in
strlen() off the thermal_zone_device_unregister() path.
Don't unregister if name is NULL, for that case we failed registering.
Do the same for the cooling zone.
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 773c7220e22d193e5667c352fcbf8d47eefc817f ]
In the case of a graceful set of detaches, where the virtio-scsi-ccw
disk is removed from the guest prior to the controller, the guest
behaves quite normally. Specifically, the detach gets us into
sd_sync_cache to issue a Synchronize Cache(10) command, which
immediately fails (and is retried a couple of times) because the device
has been removed. Later, the removal of the controller sees two CRWs
presented, but there's no further indication of the removal from the
guest viewpoint.
[ 17.217458] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 17.219257] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 21.449400] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2
[ 21.449406] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0
However, on s390, the SCSI disks can be removed "by surprise" when an
entire controller (host) is removed and all associated disks are removed
via the loop in scsi_forget_host. The same call to sd_sync_cache is
made, but because the controller has already been removed, the
Synchronize Cache(10) command is neither issued (and then failed) nor
rejected.
That the I/O isn't returned means the guest cannot have other devices
added nor removed, and other tasks (such as shutdown or reboot) issued
by the guest will not complete either. The virtio ring has already been
marked as broken (via virtio_break_device in virtio_ccw_remove), but we
still attempt to queue the command only to have it remain there. The
calling sequence provides a bit of distinction for us:
virtscsi_queuecommand()
-> virtscsi_kick_cmd()
-> virtscsi_add_cmd()
-> virtqueue_add_sgs()
-> virtqueue_add()
if success
return 0
elseif vq->broken or vring_mapping_error()
return -EIO
else
return -ENOSPC
A return of ENOSPC is generally a temporary condition, so returning
"host busy" from virtscsi_queuecommand makes sense here, to have it
redriven in a moment or two. But the EIO return code is more of a
permanent error and so it would be wise to return the I/O itself and
allow the calling thread to finish gracefully. The result is these four
kernel messages in the guest (the fourth one does not occur prior to
this patch):
[ 22.921562] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2
[ 22.921580] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0
[ 22.921978] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 22.921993] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
I opted to fill in the same response data that is returned from the more
graceful device detach, where the disk device is removed prior to the
controller device.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 90c311b0eeead647b708a723dbdde1eda3dcad05 ]
During an OOM scenario, request slots could not be created as skb
allocation fails. So the netback cannot pass in packets and netfront
wrongly assumes that there is no more work to be done and it disables
polling. This causes Rx to stall.
The issue is with the retry logic which schedules the timer if the
created slots are less than NET_RX_SLOTS_MIN. The count of new request
slots to be pushed are calculated as a difference between new req_prod
and rsp_cons which could be more than the actual slots, if there are
unconsumed responses.
The fix is to calculate the count of newly created slots as the
difference between new req_prod and old req_prod.
Signed-off-by: Vineeth Remanan Pillai <vineethp@amazon.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f1225ee4c8fcf09afaa199b8b1f0450f38b8cd11 ]
In xen_swiotlb_map_page and xen_swiotlb_map_sg_attrs, if the original
page is not suitable, we swap it for another page from the swiotlb
pool.
In these cases, we don't update the previously calculated dma address
for the page before calling xen_dma_map_page. Thus, we end up calling
xen_dma_map_page passing the wrong dev_addr, resulting in
xen_dma_map_page mistakenly assuming that the page is foreign when it is
local.
Fix the bug by updating dev_addr appropriately.
This change has no effect on x86, because xen_dma_map_page is a stub
there.
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Pooya Keshavarzi <Pooya.Keshavarzi@de.bosch.com>
Tested-by: Pooya Keshavarzi <Pooya.Keshavarzi@de.bosch.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8379cadf71c3ee8173a1c6fc1ea7762a9638c047 ]
Using control_work instead of config_work as the 3rd argument to
container_of results in an invalid portdev pointer. Indeed, the work
structure is initialized as below:
INIT_WORK(&portdev->config_work, &config_work_handler);
It leads to a crash when portdev->vdev is dereferenced later. This
bug
is triggered when the guest uses a virtio-console without multiport
feature and receives a config_changed virtio interrupt.
Signed-off-by: G. Campana <gcampana@quarkslab.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 69fed99baac186013840ced3524562841296034f ]
A driver using dev_alloc_page() must not reuse a page that had to
use emergency memory reserve.
Otherwise all packets using this page will be immediately dropped,
unless for very specific sockets having SOCK_MEMALLOC bit set.
This issue might be hard to debug, because only a fraction of the RX
ring buffer would suffer from drops.
Fixes: 75354148ce69 ("gianfar: Add paged allocation and Rx S/G")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 719ca8111402aa6157bd83a3c966d184db0d8956 ]
In the TPA GRO code path, initialize the tcp_opt_len variable to 0 so
that it will be correct for packets without TCP timestamps. The bug
caused the SKB fields to be incorrectly set up for packets without
TCP timestamps, leading to these packets being rejected by the stack.
Reported-by: Andy Gospodarek <andrew.gospodarek@broadocm.com>
Acked-by: Andy Gospodarek <andrew.gospodarek@broadocm.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f16f1df65f1cf139ff9e9f84661e6573d6bb27fc ]
vif->lock is used to protect statistics gathering agents from using the
queue structure during cleaning.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9a6cdf52b85ea5fb21d2bb31e4a7bc61b79923a7 ]
Eliminate memory leaks introduced several years ago by cleaning the
queue resources which are allocated on XenBus connection event. Namely, queue
structure array and pages used for IO rings.
Signed-off-by: Igor Druzhinin <igor.druzhinin@citrix.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e6afb1ad88feddf2347ea779cfaf4d03d3cd40b6 upstream.
Commit beb0babfb77e ("korina: disable napi on close and restart")
introduced calls to napi_disable() that were missing before,
unfortunately this leaves a small window during which NAPI has a chance
to run, yet we just freed resources since korina_free_ring() has been
called:
Fix this by disabling NAPI first then freeing resource, and make sure
that we also cancel the restart task before doing the resource freeing.
Fixes: beb0babfb77e ("korina: disable napi on close and restart")
Reported-by: Alexandros C. Couloumbis <alex@ozo.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 93b43fd137cd8865adf9978ab9870a344365d3af ]
This PHY with fiber support is register compatible with DP83848,
so add support for it.
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 17324b6add82d6c0bf119f1d1944baef392a4e39 ]
New hainan parts require updated smc firmware.
Cc: Sonny Jiang <sonny.jiang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 50a1ebc70a2803deb7811fc73fb55d70e353bc34 ]
need to clear bit31-29 in GRBM_GFX_INDEX,
then the program can be valid.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 4f060736f29a960aba8e781a88837464756200a8 ]
Termination of Immediate Notify IOCB was using wrong
IOCB handle. IOCB completion code was unable to find
appropriate code path due to wrong handle.
Following message is seen in the logs.
"Error entry - invalid handle/queue (ffff)."
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed word order in patch title ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 5f35509db179ca7ed1feaa4b14f841adb06ed220 ]
Corrupted ATIO is defined as length of fcp_header & fcp_cmd
payload is less than 0x38. It's the minimum size for a frame to
carry 8..16 bytes SCSI CDB. The exchange will be dropped or
terminated if corrupted.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
[ bvanassche: Fixed spelling in patch title ]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 8667f515952feefebb3c0f8d9a9266c91b101a46 ]
Set the elsiocb contexts to NULL after freeing as others depend on it.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit a249708bc2aa1fe3ddf15dfac22bee519d15996b ]
The function stmmac_dt_phy provides several possibilities for initializing
plat->mdio_node, all of which have the effect of increasing the reference
count of the assigned value. This field is not updated elsewhere, so the
value is live until the end of the lifetime of plat (devm_allocated), just
after the end of stmmac_remove_config_dt. Thus, add an of_node_put on
plat->mdio_node in stmmac_remove_config_dt. It is possible that the field
mdio_node is never initialized, but of_node_put is NULL-safe, so it is also
safe to call of_node_put in that case.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 26f2819772af891dee2843e1f8662c58e5129d5f ]
Zoned block devices force the use of READ/WRITE(16) commands by setting
sdkp->use_16_for_rw and clearing sdkp->use_10_for_rw. This result in
DPOFUA always being disabled for these drives as the assumed use of
the deprecated READ/WRITE(6) commands only looks at sdkp->use_10_for_rw.
Strenghten the test by also checking that sdkp->use_16_for_rw is false.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 71df1d7ccad1c36f7321d6b3b48f2ea42681c363 upstream.
The be structure must not be freed when freeing the blkif structure
isn't done. Otherwise a use-after-free of be when unmapping the ring
used for communicating with the frontend will occur in case of a
late call of xenblk_disconnect() (e.g. due to an I/O still active
when trying to disconnect).
Signed-off-by: Juergen Gross <jgross@suse.com>
Tested-by: Steven Haigh <netwiz@crc.id.au>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 57f3986231bb2c69a55ccab1d2b30a00818027ac ]
The patches regarding eee-broken-modes was merged before all people
involved could find an agreement on the best way to move forward.
While we agreed on having a DT property to mark particular modes as broken,
the value used for eee-broken-modes mapped the phy register in very direct
way. Because of this, the concern is that it could be used to implement
configuration policies instead of describing a broken HW.
In the end, having a boolean property for each mode seems to be preferred
over one bit field value mapping the register (too) directly.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 3bb9ab63276696988d8224f52db20e87194deb4b ]
In genphy_config_eee_advert, the return value of phy_read_mmd_indirect is
checked to know if the register could be accessed but the result is
assigned to a 'u32'.
Changing to 'int' to correctly get errors from phy_read_mmd_indirect.
Fixes: d853d145ea3e ("net: phy: add an option to disable EEE advertisement")
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d853d145ea3e63387a2ac759aa41d5e43876e561 ]
This patch adds an option to disable EEE advertisement in the generic PHY
by providing a mask of prohibited modes corresponding to the value found in
the MDIO_AN_EEE_ADV register.
On some platforms, PHY Low power idle seems to be causing issues, even
breaking the link some cases. The patch provides a convenient way for these
platforms to disable EEE advertisement and work around the issue.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b3ce3ce02d146841af012d08506b4071db8ffde3 upstream.
When system try to close /dev/usb-ffs/adb/ep0 on one core, at the same
time another core try to attach new UDC, which will cause deadlock as
below scenario. Thus we should release ffs lock before issuing
unregister_gadget_item().
[ 52.642225] c1 ======================================================
[ 52.642228] c1 [ INFO: possible circular locking dependency detected ]
[ 52.642236] c1 4.4.6+ #1 Tainted: G W O
[ 52.642241] c1 -------------------------------------------------------
[ 52.642245] c1 usb ffs open/2808 is trying to acquire lock:
[ 52.642270] c0 (udc_lock){+.+.+.}, at: [<ffffffc00065aeec>]
usb_gadget_unregister_driver+0x3c/0xc8
[ 52.642272] c1 but task is already holding lock:
[ 52.642283] c0 (ffs_lock){+.+.+.}, at: [<ffffffc00066b244>]
ffs_data_clear+0x30/0x140
[ 52.642285] c1 which lock already depends on the new lock.
[ 52.642287] c1
the existing dependency chain (in reverse order) is:
[ 52.642295] c0
-> #1 (ffs_lock){+.+.+.}:
[ 52.642307] c0 [<ffffffc00012340c>] __lock_acquire+0x20f0/0x2238
[ 52.642314] c0 [<ffffffc000123b54>] lock_acquire+0xe4/0x298
[ 52.642322] c0 [<ffffffc000aaf6e8>] mutex_lock_nested+0x7c/0x3cc
[ 52.642328] c0 [<ffffffc00066f7bc>] ffs_func_bind+0x504/0x6e8
[ 52.642334] c0 [<ffffffc000654004>] usb_add_function+0x84/0x184
[ 52.642340] c0 [<ffffffc000658ca4>] configfs_composite_bind+0x264/0x39c
[ 52.642346] c0 [<ffffffc00065b348>] udc_bind_to_driver+0x58/0x11c
[ 52.642352] c0 [<ffffffc00065b49c>] usb_udc_attach_driver+0x90/0xc8
[ 52.642358] c0 [<ffffffc0006598e0>] gadget_dev_desc_UDC_store+0xd4/0x128
[ 52.642369] c0 [<ffffffc0002c14e8>] configfs_write_file+0xd0/0x13c
[ 52.642376] c0 [<ffffffc00023c054>] vfs_write+0xb8/0x214
[ 52.642381] c0 [<ffffffc00023cad4>] SyS_write+0x54/0xb0
[ 52.642388] c0 [<ffffffc000085ff0>] el0_svc_naked+0x24/0x28
[ 52.642395] c0
-> #0 (udc_lock){+.+.+.}:
[ 52.642401] c0 [<ffffffc00011e3d0>] print_circular_bug+0x84/0x2e4
[ 52.642407] c0 [<ffffffc000123454>] __lock_acquire+0x2138/0x2238
[ 52.642412] c0 [<ffffffc000123b54>] lock_acquire+0xe4/0x298
[ 52.642420] c0 [<ffffffc000aaf6e8>] mutex_lock_nested+0x7c/0x3cc
[ 52.642427] c0 [<ffffffc00065aeec>] usb_gadget_unregister_driver+0x3c/0xc8
[ 52.642432] c0 [<ffffffc00065995c>] unregister_gadget_item+0x28/0x44
[ 52.642439] c0 [<ffffffc00066b34c>] ffs_data_clear+0x138/0x140
[ 52.642444] c0 [<ffffffc00066b374>] ffs_data_reset+0x20/0x6c
[ 52.642450] c0 [<ffffffc00066efd0>] ffs_data_closed+0xac/0x12c
[ 52.642454] c0 [<ffffffc00066f070>] ffs_ep0_release+0x20/0x2c
[ 52.642460] c0 [<ffffffc00023dbe4>] __fput+0xb0/0x1f4
[ 52.642466] c0 [<ffffffc00023dd9c>] ____fput+0x20/0x2c
[ 52.642473] c0 [<ffffffc0000ee944>] task_work_run+0xb4/0xe8
[ 52.642482] c0 [<ffffffc0000cd45c>] do_exit+0x360/0xb9c
[ 52.642487] c0 [<ffffffc0000cf228>] do_group_exit+0x4c/0xb0
[ 52.642494] c0 [<ffffffc0000dd3c8>] get_signal+0x380/0x89c
[ 52.642501] c0 [<ffffffc00008a8f0>] do_signal+0x154/0x518
[ 52.642507] c0 [<ffffffc00008af00>] do_notify_resume+0x70/0x78
[ 52.642512] c0 [<ffffffc000085ee8>] work_pending+0x1c/0x20
[ 52.642514] c1
other info that might help us debug this:
[ 52.642517] c1 Possible unsafe locking scenario:
[ 52.642518] c1 CPU0 CPU1
[ 52.642520] c1 ---- ----
[ 52.642525] c0 lock(ffs_lock);
[ 52.642529] c0 lock(udc_lock);
[ 52.642533] c0 lock(ffs_lock);
[ 52.642537] c0 lock(udc_lock);
[ 52.642539] c1
*** DEADLOCK ***
[ 52.642543] c1 1 lock held by usb ffs open/2808:
[ 52.642555] c0 #0: (ffs_lock){+.+.+.}, at: [<ffffffc00066b244>]
ffs_data_clear+0x30/0x140
[ 52.642557] c1 stack backtrace:
[ 52.642563] c1 CPU: 1 PID: 2808 Comm: usb ffs open Tainted: G
[ 52.642565] c1 Hardware name: Spreadtrum SP9860g Board (DT)
[ 52.642568] c1 Call trace:
[ 52.642573] c1 [<ffffffc00008b430>] dump_backtrace+0x0/0x170
[ 52.642577] c1 [<ffffffc00008b5c0>] show_stack+0x20/0x28
[ 52.642583] c1 [<ffffffc000422694>] dump_stack+0xa8/0xe0
[ 52.642587] c1 [<ffffffc00011e548>] print_circular_bug+0x1fc/0x2e4
[ 52.642591] c1 [<ffffffc000123454>] __lock_acquire+0x2138/0x2238
[ 52.642595] c1 [<ffffffc000123b54>] lock_acquire+0xe4/0x298
[ 52.642599] c1 [<ffffffc000aaf6e8>] mutex_lock_nested+0x7c/0x3cc
[ 52.642604] c1 [<ffffffc00065aeec>] usb_gadget_unregister_driver+0x3c/0xc8
[ 52.642608] c1 [<ffffffc00065995c>] unregister_gadget_item+0x28/0x44
[ 52.642613] c1 [<ffffffc00066b34c>] ffs_data_clear+0x138/0x140
[ 52.642618] c1 [<ffffffc00066b374>] ffs_data_reset+0x20/0x6c
[ 52.642621] c1 [<ffffffc00066efd0>] ffs_data_closed+0xac/0x12c
[ 52.642625] c1 [<ffffffc00066f070>] ffs_ep0_release+0x20/0x2c
[ 52.642629] c1 [<ffffffc00023dbe4>] __fput+0xb0/0x1f4
[ 52.642633] c1 [<ffffffc00023dd9c>] ____fput+0x20/0x2c
[ 52.642636] c1 [<ffffffc0000ee944>] task_work_run+0xb4/0xe8
[ 52.642640] c1 [<ffffffc0000cd45c>] do_exit+0x360/0xb9c
[ 52.642644] c1 [<ffffffc0000cf228>] do_group_exit+0x4c/0xb0
[ 52.642647] c1 [<ffffffc0000dd3c8>] get_signal+0x380/0x89c
[ 52.642651] c1 [<ffffffc00008a8f0>] do_signal+0x154/0x518
[ 52.642656] c1 [<ffffffc00008af00>] do_notify_resume+0x70/0x78
[ 52.642659] c1 [<ffffffc000085ee8>] work_pending+0x1c/0x20
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 00a0ea33b495ee6149bf5a77ac5807ce87323abb upstream.
process_prepared_discard_passdown_pt1() should cleanup
dm_thin_new_mapping in cases of error.
dm_pool_inc_data_range() can fail trying to get a block reference:
metadata operation 'dm_pool_inc_data_range' failed: error = -61
When dm_pool_inc_data_range() fails, dm thin aborts current metadata
transaction and marks pool as PM_READ_ONLY. Memory for thin mapping
is released as well. However, current thin mapping will be queued
onto next stage as part of queue_passdown_pt2() or passdown_endio().
This dangling thin mapping memory when processed and accessed in
next stage will lead to device mapper crashing.
Code flow without fix:
-> process_prepared_discard_passdown_pt1(m)
-> dm_thin_remove_range()
-> discard passdown
--> passdown_endio(m) queues m onto next stage
-> dm_pool_inc_data_range() fails, frees memory m
but does not remove it from next stage queue
-> process_prepared_discard_passdown_pt2(m)
-> processes freed memory m and crashes
One such stack:
Call Trace:
[<ffffffffa037a46f>] dm_cell_release_no_holder+0x2f/0x70 [dm_bio_prison]
[<ffffffffa039b6dc>] cell_defer_no_holder+0x3c/0x80 [dm_thin_pool]
[<ffffffffa039b88b>] process_prepared_discard_passdown_pt2+0x4b/0x90 [dm_thin_pool]
[<ffffffffa0399611>] process_prepared+0x81/0xa0 [dm_thin_pool]
[<ffffffffa039e735>] do_worker+0xc5/0x820 [dm_thin_pool]
[<ffffffff8152bf54>] ? __schedule+0x244/0x680
[<ffffffff81087e72>] ? pwq_activate_delayed_work+0x42/0xb0
[<ffffffff81089f53>] process_one_work+0x153/0x3f0
[<ffffffff8108a71b>] worker_thread+0x12b/0x4b0
[<ffffffff8108a5f0>] ? rescuer_thread+0x350/0x350
[<ffffffff8108fd6a>] kthread+0xca/0xe0
[<ffffffff8108fca0>] ? kthread_park+0x60/0x60
[<ffffffff81530b45>] ret_from_fork+0x25/0x30
The fix is to first take the block ref count for discarded block and
then do a passdown discard of this block. If block ref count fails,
then bail out aborting current metadata transaction, mark pool as
PM_READ_ONLY and also free current thin mapping memory (existing error
handling code) without queueing this thin mapping onto next stage of
processing. If block ref count succeeds, then passdown discard of this
block. Discard callback of passdown_endio() will queue this thin mapping
onto next stage of processing.
Code flow with fix:
-> process_prepared_discard_passdown_pt1(m)
-> dm_thin_remove_range()
-> dm_pool_inc_data_range()
--> if fails, free memory m and bail out
-> discard passdown
--> passdown_endio(m) queues m onto next stage
Reviewed-by: Eduardo Valentin <eduval@amazon.com>
Reviewed-by: Cristian Gafton <gafton@amazon.com>
Reviewed-by: Anchal Agarwal <anchalag@amazon.com>
Signed-off-by: Vallish Vaidyeshwara <vallish@amazon.com>
Reviewed-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 82fcee526ba8ca2c5d378bdf51b21b7eb058fe3a upstream.
The hash table created during vmw_cmdbuf_res_man_create was
never freed. This causes memory leak in context creation.
Added the corresponding drm_ht_remove in vmw_cmdbuf_res_man_destroy.
Tested for memory leak by running piglit overnight and kernel
memory is not inflated which earlier was.
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ad537b822577fcc143325786cd6ad50d7b9df31c upstream.
GPIOEVENT_REQUEST_BOTH_EDGES is not a single flag, but a binary OR of
GPIOEVENT_REQUEST_RISING_EDGE and GPIOEVENT_REQUEST_FALLING_EDGE.
The expression 'le->eflags & GPIOEVENT_REQUEST_BOTH_EDGES' we'll get
evaluated to true even if only one event type was requested.
Fix it by checking both RISING & FALLING flags explicitly.
Fixes: 61f922db7221 ("gpio: userspace ABI for reading GPIO line events")
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 71f677a91046599ece96ebab21df956ce909c456 upstream.
The ast driver configures a window to enable access into BMC
memory space in order to read some configuration registers.
If this window is disabled, which it can be from the BMC side,
the ast driver can't function.
Closing this window is a necessity for security if a machine's
host side and BMC side are controlled by different parties;
i.e. a cloud provider offering machines "bare metal".
A recent patch went in to try to check if that window is open
but it does so by trying to access the registers in question
and testing if the result is 0xffffffff.
This method will trigger a PCIe error when the window is closed
which on some systems will be fatal (it will trigger an EEH
for example on POWER which will take out the device).
This patch improves this in two ways:
- First, if the firmware has put properties in the device-tree
containing the relevant configuration information, we use these.
- Otherwise, a bit in one of the SCU scratch registers (which
are readable via the VGA register space and writeable by the BMC)
will indicate if the BMC has closed the window. This bit has been
defined by Y.C Chen from Aspeed.
If the window is closed and the configuration isn't available from
the device-tree, some sane defaults are used. Those defaults are
hopefully sufficient for standard video modes used on a server.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a24fa22ce22ae302b3bf8f7008896d52d5d57b8d upstream.
There is no need to use xen_blkif_get()/xen_blkif_put() in the kthread
of xen-blkback. Thread stopping is synchronous and using the blkif
reference counting in the kthread will avoid to ever let the reference
count drop to zero at the end of an I/O running concurrent to
disconnecting and multiple rings.
Setting ring->xenblkd to NULL after stopping the kthread isn't needed
as the kthread does this already.
Signed-off-by: Juergen Gross <jgross@suse.com>
Tested-by: Steven Haigh <netwiz@crc.id.au>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
efx_probe_all() calls efx->type->vswitching_probe during probe. For
SFC4000 (Falcon) NICs this function is not defined, leading to a BUG
with the top of the call stack similar to:
? efx_pci_probe_main+0x29a/0x830
efx_pci_probe+0x7d3/0xe70
vswitching_restore and vswitching_remove also need to be defined.
Fixed in mainline by:
commit 5a6681e22c14 ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
Fixes: 6d8aaaf6f798 ("sfc: create VEB vswitch and vport above default firmware setup")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit f0b381178b01b831f9907d72f467d6443afdea67 ]
Misuse of (BIT) macro caused to report wrong flags for
"Hardware Transmit Timestamp Modes" and "Hardware Receive
Filter Modes"
Fixes: ef9814deafd0 ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Maor Dickman <maord@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 6c780a0267b8a1075f40b39851132eeaefefcff5 ]
Before attempting to initialize the command interface we must wait till
the fw_initializing bit is clear.
If we fail to meet this condition the hardware will drop our
configuration, specifically the descriptors page address. This scenario
can happen when the firmware is still executing an FLR flow and did not
finish yet so the driver needs to wait for that to finish.
Fixes: e3297246c2c8 ('net/mlx5_core: Wait for FW readiness on startup')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 31ac93386d135a6c96de9c8bab406f5ccabf5a4d ]
The error flow of mlx5e_create_netdev calls the cleanup call
of the given profile without checking if it exists, fix that.
Currently the VF reps don't register that callback and we crash
if getting into error -- can be reproduced by the user doing ctrl^C
while attempting to change the sriov mode from legacy to switchdev.
Fixes: 26e59d8077a3 '(net/mlx5e: Implement mlx5e interface attach/detach callbacks')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Sabrina Dubroca <sdubroca@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 53acd76ce571e3b71f9205f2d49ab285a9f1aad8 ]
DIM (Dynamically-tuned Interrupt Moderation) is a mechanism designed for
changing the channel interrupt moderation values in order to reduce CPU
overhead for all traffic types.
Each iteration of the algorithm, DIM calculates the difference in
throughput, packet rate and interrupt rate from last iteration in order
to make a decision. DIM relies on counters for each metric. When these
counters get to their type's max value they wraparound. In this case
the delta between 'end' and 'start' samples is negative and when
translated to unsigned integers - very high. This results in a false
indication to the algorithm and might result in a wrong decision.
The fix calculates the 'distance' between 'end' and 'start' samples in a
cyclic way around the relevant type's max value. It can also be viewed as
an absolute value around the type's max value instead of around 0.
Testing show higher stability in DIM profile selection and no wraparound
issues.
Fixes: cb3c7fd4f839 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit c3164d2fc48fd4fa0477ab658b644559c3fe9073 ]
DIM (Dynamically-tuned Interrupt Moderation) is a mechanism designed for
changing the channel interrupt moderation values in order to reduce CPU
overhead for all traffic types.
Until now only interrupt and packet rate were sampled.
We found a scenario on which we get a false indication since a change in
DIM caused more aggregation and reduced packet rate while increasing BW.
We now regard a change as succesfull iff:
current_BW > (prev_BW + threshold) or
current_BW ~= prev_BW and current_PR > (prev_PR + threshold) or
current_BW ~= prev_BW and current_PR ~= prev_PR and
current_IR < (prev_IR - threshold)
Where BW = Bandwidth, PR = Packet rate and IR = Interrupt rate
Improvements (ConnectX-4Lx 25GbE, single RX queue, LRO off)
--------------------------------------------------
packet size | before[Mb/s] | after[Mb/s] | gain |
2B | 343.4 | 359.4 | 4.5% |
16B | 2739.7 | 2814.8 | 2.7% |
64B | 9739 | 10185.3 | 4.5% |
Fixes: cb3c7fd4f839 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 097d3c9508dc58286344e4a22b300098cf0c1566 ]
Commit 1aa6c4f6b8cd8 ("net: vrf: Add l3mdev rules on first device create")
adds the l3mdev FIB rule the first time a VRF device is created. However,
it only creates the rule once and only in the namespace the first device
is created - which may not be init_net. Fix by using the net_generic
capability to make the add_fib_rules flag per network namespace.
Fixes: 1aa6c4f6b8cd8 ("net: vrf: Add l3mdev rules on first device create")
Reported-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 35abcd4f9f303ac4f10f99b3f7e993e5f2e6fa37 upstream.
This fixes the following warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c: In function
'brcmf_usb_probe_phase2':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/usb.c:1198:2:
warning: 'devinfo' may be used uninitialized in this function
[-Wmaybe-uninitialized]
mutex_unlock(&devinfo->dev_init_lock);
Fixes: 6d0507a777fb ("brcmfmac: add parameter to pass error code in firmware callback")
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 898805e0cdf7fd860ec21bf661d3a0285a3defbd upstream.
The Marvell driver incorrectly provides phydev->lp_advertising as the
logical and of the link partner's advert and our advert. This is
incorrect - this field is supposed to store the link parter's unmodified
advertisment.
This allows ethtool to report the correct link partner auto-negotiation
status.
Fixes: be937f1f89ca ("Marvell PHY m88e1111 driver fix")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 833bfade96561216aa2129516a5926a0326860a2 upstream.
The generic SPI code calculates how long the issued transfer would take
and adds 100ms in addition to the timeout as tolerance. On my 500 MHz
Lantiq Mips SoC I am getting timeouts from the SPI like this when the
system boots up:
m25p80 spi32766.4: SPI transfer timed out
blk_update_request: I/O error, dev mtdblock3, sector 2
SQUASHFS error: squashfs_read_data failed to read block 0x6e
After increasing the tolerance for the timeout to 200ms I haven't seen
these SPI transfer time outs any more.
The Lantiq SPI driver in use here has an extra work queue in between,
which gets triggered when the controller send the last word and the
hardware FIFOs used for reading and writing are only 8 words long.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2201ac6129fa162ac24da089a034bb0971648ebb upstream.
The code responsible for splitting periods into chunks that
can be handled by the DMA controller missed to update total_len,
the number of bytes processed in the current period, when there
are more chunks to follow.
Therefore total_len was stuck at 0 and the code didn't work at all.
This resulted in a wrong control block layout and audio issues because
the cyclic DMA callback wasn't executing on period boundaries.
Fix this by adding the missing total_len update.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Tested-by: Clive Messer <clive.messer@digitaldreamtime.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|