| Age | Commit message (Collapse) | Author |
|---|
|
Instead of modifying the HT SMPS capability field
for stations, track the SMPS mode explicitly in a
new field in the station struct and use it in the
drivers that care about it. This simplifies the
code using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For HT and VHT the current bandwidth can change,
add the function ieee80211_vif_change_bandwidth()
to take care of this. It returns a failure if the
new bandwidth isn't compatible with the existing
channel context, the caller has to handle that.
When it happens, also inform the driver that the
bandwidth changed for this virtual interface (no
drivers would actually care today though.)
Changing to/from HT/VHT isn't allowed though.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Handle the operating mode notification action frame.
When the supported streams or the bandwidth change
let the driver and rate control algorithm know.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
With VHT, a station can change the number of spatial
streams it can receive on the fly, not unlike spatial
multiplexing in HT. Prepare for that by tracking the
maximum number of spatial streams it can receive when
the connection is established.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For VHT, many more bandwidth changes are possible. As a first
step, stop toggling the IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag
in the HT capabilities and instead introduce a bandwidth field
indicating the currently usable bandwidth to transmit to the
station. Of course, make all drivers use it.
To achieve this, make ieee80211_ht_cap_ie_to_sta_ht_cap() get
the station as an argument, rather than the new capabilities,
so it can set up the new bandwidth field.
If the station is a VHT station and VHT bandwidth is in use,
also set the bandwidth accordingly.
Doing this allows us to get rid of the supports_40mhz flag as
the HT capabilities now reflect the true capability instead of
the current setting.
While at it, also fix ieee80211_ht_cap_ie_to_sta_ht_cap() to not
ignore HT cap overrides when MCS TX isn't supported (not that it
really happens...)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add command to trigger radar detection in the driver/FW.
Once radar detection is started it should continuously
monitor for radars as long as the channel active.
If radar is detected usermode notified with 'radar
detected' event.
Scanning and remain on channel functionality must be disabled
while doing radar detection/scanning, and vice versa.
Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Scans currently work by stopping the netdev tx queues but leaving the
mac80211 queues active. This stops the flow of incoming packets while
still allowing mac80211 to transmit nullfunc and probe request frames to
facilitate scanning. However, the driver may try to wake the mac80211
queues while in this state, which will also wake the netdev queues.
To prevent this, add a new queue stop reason,
IEEE80211_QUEUE_STOP_REASON_OFFCHANNEL, to be used when stopping the tx
queues for off-channel operation. This prevents the netdev queues from
waking when a driver wakes the mac80211 queues.
This also stops all frames from being transmitted, even those meant to
be sent off-channel. Add a new tx control flag,
IEEE80211_TX_CTL_OFFCHAN_TX_OK, which allows frames to be transmitted
when the queues are stopped only for the off-channel stop reason. Update
all locations transmitting off-channel frames to use this flag.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are only a few drivers that use HW scan, and
all of those don't need a non-idle transition before
starting the scan -- some don't even care about idle
at all. Remove the flag and code associated with it.
The only driver that really actually needed this is
wl1251 and it can just do it itself in the hw_scan
callback -- implement that.
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The functions were added for some sort of Bluetooth
coexistence, but aren't used, so remove them again.
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In order to be able to predict the next DTIM TBTT
in the driver, add the ability to use timing data
from beacons only with the new hardware flag
IEEE80211_HW_TIMING_BEACON_ONLY and the BSS info
value sync_dtim_count which is only valid if the
timing data came from a beacon. The data can only
come from a beacon, and if no beacon was received
before association it is updated later together
with the DTIM count notification.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add debugfs driver callbacks so drivers can add
debugfs entries for interfaces. Note that they
_must_ remove the entries again as add/remove in
the driver doesn't correspond to add/remove in
debugfs; the former is up/down while the latter
is netdev create/destroy.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
With multi-channel, there's a corner case where a driver
doesn't receive a beacon soon enough to be able to sync
its timers with the AP. In this case, the only recovery
(after trying again) is to disconnect from the AP. Allow
calling ieee80211_connection_loss() for such cases. To
make that possible, modify the work function to not rely
on the IEEE80211_HW_CONNECTION_MONITOR flag but use new
state kept in the interface instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When sending authentication/association frames they
might take a bit of time to go out because we may
have to synchronise with the AP, in particular in
the case where it's really a P2P GO. In this case
the 200ms fixed timeout could potentially be too
short if the beacon interval is relatively large.
For drivers that report TX status we can do better.
Instead of starting the timeout directly, start it
only when the frame status arrives. Since then the
frame was out on the air, we can wait shorter (the
typical response time is supposed to be 30ms, wait
100ms.) Also, if the frame failed to be transmitted
try again right away instead of waiting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, when the driver requires the DTIM period,
mac80211 will wait to hear a beacon before association.
This behavior is suboptimal since some drivers may be
able to deal with knowing the DTIM period after the
association, if they get it at all.
To address this, notify the drivers with bss_info_changed
with the new BSS_CHANGED_DTIM_PERIOD flag when the DTIM
becomes known. This might be when changing to associated,
or later when the entire association was done with only
probe response information.
Rename the hardware flag for the current behaviour to
IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC to more accurately
reflect its behaviour. IEEE80211_HW_NEED_DTIM_PERIOD is
no longer accurate as all drivers get the DTIM period
now, just not before association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When waking up from WoWLAN, it is useful to know
what triggered the wakeup. Support reporting the
wakeup reason(s) in cfg80211 (and a pass-through
in mac80211) to allow userspace to know.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is basically a revert of:
commit 5b632fe85ec82e5c43740b52e74c66df50a37db3
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Mon Dec 3 12:56:33 2012 +0100
mac80211: introduce IEEE80211_HW_TEARDOWN_AGGR_ON_BAR_FAIL
We do not need this flag any longer, rt2x00 BAR/BA problem was fixed
correctly by wireless-testing commit:
commit 84e9e8ebd369679a958200a8baca96aafb2393bb
Author: Helmut Schaa <helmut.schaa@googlemail.com>
Date: Thu Jan 17 17:34:32 2013 +0100
rt2x00: Improve TX status handling for BlockAckReq frames
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since drivers can support several BSS / P2P Client
interfaces, the rssi callback needs to inform the driver
about the interface teh rssi event relates to.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
To be able to implement NS response offloading (in
regular operation or while in WoWLAN) drivers need
to know the IPv6 addresses assigned to interfaces.
Implement an IPv6 notifier in mac80211 to call the
driver when addresses change.
Unlike for IPv4, implement it as a callback rather
than as a list in the BSS configuration, that is
more flexible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Depending on the driver, having ARP filtering for
some addresses may be possible. Remove the logic
that tracks whether ARP filter is enabled or not
and give the driver the total number of addresses
instead of the length of the list so it can make
its own decision.
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are hardwares which support offload of data packets
for example when auto ARP is enabled the hw will send
the ARP response. In such cases if WEP encryption is
configured the hw must know the default WEP key in order
to encrypt the packets correctly.
When hw_accel is enabled and encryption type is set to WEP,
the driver should get the default key index from mac80211.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
[cleanups, fixes, documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When the driver's resume function can't completely
restore the configuration in the device, it returns
1 from the callback which will be treated like a HW
restart request, but done directly.
In this case, also call the driver's restart_complete()
function so it can finish the reconfiguration there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When building the 80211 DocBook, scripts/kernel-doc reports
the following type of warnings:
Warning(include/net/cfg80211.h:334): No description found for return value of 'cfg80211_get_chandef_type'
These warnings are only reported when scripts/kernel-doc
runs in verbose mode.
To fix these use "Return:" to describe function return values.
Signed-off-by: Yacine Belkadi <yacine.belkadi.1@gmail.com>
[adjust for freq_reg_info() change]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Use __aligned(...) instead of __attribute__((aligned(...)))
in mac80211 and cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When TX aggregation is stopped, there are a few
different cases:
- connection with the peer was dropped
- session stop was requested locally
- session stop was requested by the peer
- connection was dropped while a session is stopping
The behaviour in these cases should be different, if
the connection is dropped then the driver should drop
all frames, otherwise the frames may continue to be
transmitted, aggregated in the case of a locally
requested session stop or unaggregated in the case of
the peer requesting session stop.
Split these different cases so that the driver can
act accordingly; however, treat local and remote stop
the same way and ask the driver to not send frames as
aggregated packets any more.
In the case of connection drop, the stop callback the
driver is otherwise supposed to call is no longer
required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
During suspend/resume channel contexts might be
iterated even if they haven't been re-added to
the driver, keep track of this and skip them in
iteration. Also use the new status for sanity
checks.
Also clarify the fact that during HW restart all
contexts are iterated over (thanks Eliad.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Commit f0425beda4d404a6e751439b562100b902ba9c98 "mac80211: retry sending
failed BAR frames later instead of tearing down aggr" caused regression
on rt2x00 hardware (connection hangs). This regression was fixed by
commit be03d4a45c09ee5100d3aaaedd087f19bc20d01 "rt2x00: Don't let
mac80211 send a BAR when an AMPDU subframe fails". But the latter
commit caused yet another problem reported in
https://bugzilla.kernel.org/show_bug.cgi?id=42828#c22
After long discussion in this thread:
http://mid.gmane.org/20121018075615.GA18212@redhat.com
and testing various alternative solutions, which failed on one or other
setup, we have no other good fix for the issues like just revert both
mentioned earlier commits.
To do not affect other hardware which benefit from commit
f0425beda4d404a6e751439b562100b902ba9c98, instead of reverting it,
introduce flag that when used will restore mac80211 behaviour before
the commit.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
[replaced link with mid.gmane.org that has message-id]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of allocating a temporary buffer to build IEs
build them right into the SKB.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add some information that we have about VHT to radiotap.
This at least lets one see the MCS and NSS information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
To achieve this, limit the number of retries to
31 (instead of 255) and use the three bits that
are then free for VHT flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support to mac80211 for having drivers report
received VHT MCS information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.
Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Provide drivers with hooks to create debugfs files when
a new station is added. This would help drivers to take
advantage of mac80211's station list infrastructure and not maintain
tedious station management code internally.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
[ifdef inline wrapper functions]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Drivers (e.g. wl12xx) might need to know the vif
to roc on (mainly in order to configure the
rx filters correctly).
Add the vif to the op params, and update the current
users (iwlwifi) to use the new api.
Signed-off-by: Eliad Peller <eliad@wizery.com>
[fix hwsim]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In some cases, in particular for experimentation, it
can be useful to be able to add vendor namespace data
to received frames in addition to the normal radiotap
data.
Allow doing this through mac80211 by adding fields to
the RX status descriptor that describe the data while
the data itself is prepended to the frame.
Also add some example code to hwsim, but don't enable
it because it doesn't use a proper OUI identifier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow drivers to indicate their mactime is at RX completion and adjust
for this in mac80211. Also rename the existing RX_FLAG_MACTIME_MPDU to
RX_FLAG_MACTIME_START to clarify its intent. Based on similar code by
Johannes Berg.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix docs, atheros drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
During hardware restart, all interfaces are iterated even
though they haven't been re-added to the driver, document
this behaviour. The same also happens during resume, which
is even more confusing since all of the interfaces were
previously removed from the driver. Make this optional so
drivers relying on the current behaviour can still use it,
but to let drivers that don't want this behaviour disable
it.
Also convert all API users, keeping the old semantics
except in hwsim, where the new normal ones are desired.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When the driver requests a restart (reconfiguration) it
gets all the normal method calls, but can't really tell
why they're happening. Call a new restart_complete op
in the driver when the restart completes, so it could
keep its own state about the restart and clear it there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
While connected to a GO, parse the P2P NoA attribute
and pass the CT Window and opportunistic powersave
parameters to the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.
Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Depending on the driver, a lot of setup may be
necessary to start operating as an AP, some of
which may fail. Add an explicit AP start driver
method to make such failures easier to handle,
and add an AP stop driver method for symmetry.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Expose a function for the AES-CMAC subkey calculation
to drivers. This is the first step of the AES-CMAC
cipher key setup and may be required for CMAC hardware
offloading.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Initialization of beacon transmission in IBSS mode depends
on whether a new BSS is being created or joined. When joining
an existing IBSS network, beaconing has to start only after
a TSF-sync has happened - this is explained in 11.1.4.
Introduce a new parameter in the BSS information structure to
indicate creator/joiner mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Save the AP's VHT capabilities (in managed
mode) and make them available to the driver
in the station information.
Unlike HT capabilities, they aren't restricted
to the common capabilities, so drivers must be
aware of their own capabilities.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
[fix endian conversion bug ...]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Drivers may need to iterate the active channel
contexts, export an iterator function to allow
that. To make it possible, use RCU-safe list
functions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).
Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Introduce channel context driver methods. The channel
on a context channel is immutable, but the channel type
and other properties can change.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Channel context are the foundation for multi-channel
operation. They are are immutable and are re-created
(or re-used if other interfaces are bound to a certain
channel and a compatible channel type) on channel
switching.
This is an initial implementation and more features
will come in separate patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[some changes including RCU protection]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Mark keys that might be used to receive management
frames so drivers can fall back on software crypto
for them if they don't support hardware offload.
As the new flag is only set correctly for RX keys
and the existing IEEE80211_KEY_FLAG_SW_MGMT flag
can only affect TX, also rename the latter to
IEEE80211_KEY_FLAG_SW_MGMT_TX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
