| Age | Commit message (Collapse) | Author |
|---|
|
commit 92e55f412cffd016cc245a74278cb4d7b89bb3bc upstream.
Unlike ipv4, this control socket is shared by all cpus so we cannot use
it as scratchpad area to annotate the mark that we pass to ip6_xmit().
Add a new parameter to ip6_xmit() to indicate the mark. The SCTP socket
family caches the flowi6 structure in the sctp_transport structure, so
we cannot use to carry the mark unless we later on reset it back, which
I discarded since it looks ugly to me.
Fixes: bf99b4ded5f8 ("tcp: fix mark propagation with fwmark_reflect enabled")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 2bd137de531367fb573d90150d1872cb2a2095f7 ]
An error was reported upgrading to 4.9.8:
root@Typhoon:~# ip route add default table 210 nexthop dev eth0 via 10.68.64.1
weight 1 nexthop dev eth0 via 10.68.64.2 weight 1
RTNETLINK answers: Operation not supported
The problem occurs when CONFIG_LWTUNNEL is not enabled and a multipath
route is submitted.
The point of lwtunnel_valid_encap_type_attr is catch modules that
need to be loaded before any references are taken with rntl held. With
CONFIG_LWTUNNEL disabled, there will be no modules to load so the
lwtunnel_valid_encap_type_attr stub should just return 0.
Fixes: 9ed59592e3e3 ("lwtunnel: fix autoload of lwt modules")
Reported-by: pupilla@libero.it
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit d71b7896886345c53ef1d84bda2bc758554f5d61 ]
syzkaller found another out of bound access in ip_options_compile(),
or more exactly in cipso_v4_validate()
Fixes: 20e2a8648596 ("cipso: handle CIPSO options correctly when NetLabel is disabled")
Fixes: 446fda4f2682 ("[NetLabel]: CIPSOv4 engine")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Paul Moore <paul@paul-moore.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 85c814016ce3b371016c2c054a905fa2492f5a65 ]
When attempting to free lwtunnel state after the module for the encap
has been unloaded an oops occurs:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: lwtstate_free+0x18/0x40
[..]
task: ffff88003e372380 task.stack: ffffc900001fc000
RIP: 0010:lwtstate_free+0x18/0x40
RSP: 0018:ffff88003fd83e88 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff88002bbb3380 RCX: ffff88000c91a300
[..]
Call Trace:
<IRQ>
free_fib_info_rcu+0x195/0x1a0
? rt_fibinfo_free+0x50/0x50
rcu_process_callbacks+0x2d3/0x850
? rcu_process_callbacks+0x296/0x850
__do_softirq+0xe4/0x4cb
irq_exit+0xb0/0xc0
smp_apic_timer_interrupt+0x3d/0x50
apic_timer_interrupt+0x93/0xa0
[..]
Code: e8 6e c6 fc ff 89 d8 5b 5d c3 bb de ff ff ff eb f4 66 90 66 66 66 66 90 55 48 89 e5 53 0f b7 07 48 89 fb 48 8b 04 c5 00 81 d5 81 <48> 8b 40 08 48 85 c0 74 13 ff d0 48 8d 7b 20 be 20 00 00 00 e8
The problem is after the module for the encap can be unloaded the
corresponding ops is removed and is thus NULL here.
Modules implementing lwtunnel ops should not be allowed to unload
while there is state alive using those ops, so grab the module
reference for the ops on creating lwtunnel state and of course release
the reference when freeing the state.
Fixes: 1104d9ba443a ("lwtunnel: Add destroy state operation")
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 88ff7334f25909802140e690c0e16433e485b0a0 ]
Modules implementing lwtunnel ops should not be allowed to unload
while there is state alive using those ops, so specify the owning
module for all lwtunnel ops.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
[ Upstream commit 9ed59592e3e379b2e9557dc1d9e9ec8fcbb33f16]
Trying to add an mpls encap route when the MPLS modules are not loaded
hangs. For example:
CONFIG_MPLS=y
CONFIG_NET_MPLS_GSO=m
CONFIG_MPLS_ROUTING=m
CONFIG_MPLS_IPTUNNEL=m
$ ip route add 10.10.10.10/32 encap mpls 100 via inet 10.100.1.2
The ip command hangs:
root 880 826 0 21:25 pts/0 00:00:00 ip route add 10.10.10.10/32 encap mpls 100 via inet 10.100.1.2
$ cat /proc/880/stack
[<ffffffff81065a9b>] call_usermodehelper_exec+0xd6/0x134
[<ffffffff81065efc>] __request_module+0x27b/0x30a
[<ffffffff814542f6>] lwtunnel_build_state+0xe4/0x178
[<ffffffff814aa1e4>] fib_create_info+0x47f/0xdd4
[<ffffffff814ae451>] fib_table_insert+0x90/0x41f
[<ffffffff814a8010>] inet_rtm_newroute+0x4b/0x52
...
modprobe is trying to load rtnl-lwt-MPLS:
root 881 5 0 21:25 ? 00:00:00 /sbin/modprobe -q -- rtnl-lwt-MPLS
and it hangs after loading mpls_router:
$ cat /proc/881/stack
[<ffffffff81441537>] rtnl_lock+0x12/0x14
[<ffffffff8142ca2a>] register_netdevice_notifier+0x16/0x179
[<ffffffffa0033025>] mpls_init+0x25/0x1000 [mpls_router]
[<ffffffff81000471>] do_one_initcall+0x8e/0x13f
[<ffffffff81119961>] do_init_module+0x5a/0x1e5
[<ffffffff810bd070>] load_module+0x13bd/0x17d6
...
The problem is that lwtunnel_build_state is called with rtnl lock
held preventing mpls_init from registering.
Given the potential references held by the time lwtunnel_build_state it
can not drop the rtnl lock to the load module. So, extract the module
loading code from lwtunnel_build_state into a new function to validate
the encap type. The new function is called while converting the user
request into a fib_config which is well before any table, device or
fib entries are examined.
Fixes: 745041e2aaf1 ("lwtunnel: autoload of lwt modules")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e6f462df9acd2a3295e5d34eb29e2823220cf129 upstream.
When mac80211 abandons an association attempt, it may free
all the data structures, but inform cfg80211 and userspace
about it only by sending the deauth frame it received, in
which case cfg80211 has no link to the BSS struct that was
used and will not cfg80211_unhold_bss() it.
Fix this by providing a way to inform cfg80211 of this with
the BSS entry passed, so that it can clean up properly, and
use this ability in the appropriate places in mac80211.
This isn't ideal: some code is more or less duplicated and
tracing is missing. However, it's a fairly small change and
it's thus easier to backport - cleanups can come later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
This is a large batch of Netfilter fixes for net, they are:
1) Three patches to fix NAT conversion to rhashtable: Switch to rhlist
structure that allows to have several objects with the same key.
Moreover, fix wrong comparison logic in nf_nat_bysource_cmp() as this is
expecting a return value similar to memcmp(). Change location of
the nat_bysource field in the nf_conn structure to avoid zeroing
this as it breaks interaction with SLAB_DESTROY_BY_RCU and lead us
to crashes. From Florian Westphal.
2) Don't allow malformed fragments go through in IPv6, drop them,
otherwise we hit GPF, patch from Florian Westphal.
3) Fix crash if attributes are missing in nft_range, from Liping Zhang.
4) Fix arptables 32-bits userspace 64-bits kernel compat, from Hongxu Jia.
5) Two patches from David Ahern to fix netfilter interaction with vrf.
From David Ahern.
6) Fix element timeout calculation in nf_tables, we take milliseconds
from userspace, but we use jiffies from kernelspace. Patch from
Anders K. Pedersen.
7) Missing validation length netlink attribute for nft_hash, from
Laura Garcia.
8) Fix nf_conntrack_helper documentation, we don't default to off
anymore for a bit of time so let's get this in sync with the code.
I know is late but I think these are important, specifically the NAT
bits, as they are mostly addressing fallout from recent changes. I also
read there are chances to have -rc8, if that is the case, that would
also give us a bit more time to test this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Socket flags aren't updated atomically, so the socket must be locked
while reading the SOCK_ZAPPED flag.
This issue exists for both l2tp_ip and l2tp_ip6. For IPv6, this patch
also brings error handling for __ip6_datagram_connect() failures.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stas Nichiporovich reports oops in nf_nat_bysource_cmp(), trying to
access nf_conn struct at address 0xffffffffffffff50.
This is the result of fetching a null rhash list (struct embedded at
offset 176; 0 - 176 gets us ...fff50).
The problem is that conntrack entries are allocated from a
SLAB_DESTROY_BY_RCU cache, i.e. entries can be free'd and reused
on another cpu while nf nat bysource hash access the same conntrack entry.
Freeing is fine (we hold rcu read lock); zeroing rhlist_head isn't.
-> Move the rhlist struct outside of the memset()-inited area.
Fixes: 7c9664351980aaa6a ("netfilter: move nat hlist_head to nf_conn")
Reported-by: Stas Nichiporovich <stasn77@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
As Liping Zhang reports, after commit a8b1e36d0d1d ("netfilter: nft_dynset:
fix element timeout for HZ != 1000"), priv->timeout was stored in jiffies,
while set->timeout was stored in milliseconds. This is inconsistent and
incorrect.
Firstly, we already call msecs_to_jiffies in nft_set_elem_init, so
priv->timeout will be converted to jiffies twice.
Secondly, if the user did not specify the NFTA_DYNSET_TIMEOUT attr,
set->timeout will be used, but we forget to call msecs_to_jiffies
when do update elements.
Fix this by using jiffies internally for traditional sets and doing the
conversions to/from msec when interacting with userspace - as dynset
already does.
This is preferable to doing the conversions, when elements are inserted or
updated, because this can happen very frequently on busy dynsets.
Fixes: a8b1e36d0d1d ("netfilter: nft_dynset: fix element timeout for HZ != 1000")
Reported-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Anders K. Pedersen <akp@cohaesio.com>
Acked-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
I got offlist bug report about failing connections and high cpu usage.
This happens because we hit 'elasticity' checks in rhashtable that
refuses bucket list exceeding 16 entries.
The nat bysrc hash unfortunately needs to insert distinct objects that
share same key and are identical (have same source tuple), this cannot
be avoided.
Switch to the rhlist interface which is designed for this.
The nulls_base is removed here, I don't think its needed:
A (unlikely) false positive results in unneeded port clash resolution,
a false negative results in packet drop during conntrack confirmation,
when we try to insert the duplicate into main conntrack hash table.
Tested by adding multiple ip addresses to host, then adding
iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
... and then creating multiple connections, from same source port but
different addresses:
for i in $(seq 2000 2032);do nc -p 1234 192.168.7.1 $i > /dev/null & done
(all of these then get hashed to same bysource slot)
Then, to test that nat conflict resultion is working:
nc -s 10.0.0.1 -p 1234 192.168.7.1 2000
nc -s 10.0.0.2 -p 1234 192.168.7.1 2000
tcp .. src=10.0.0.1 dst=192.168.7.1 sport=1234 dport=2000 src=192.168.7.1 dst=192.168.7.10 sport=2000 dport=1024 [ASSURED]
tcp .. src=10.0.0.2 dst=192.168.7.1 sport=1234 dport=2000 src=192.168.7.1 dst=192.168.7.10 sport=2000 dport=1025 [ASSURED]
tcp .. src=192.168.7.10 dst=192.168.7.1 sport=1234 dport=2000 src=192.168.7.1 dst=192.168.7.10 sport=2000 dport=1234 [ASSURED]
tcp .. src=192.168.7.10 dst=192.168.7.1 sport=1234 dport=2001 src=192.168.7.1 dst=192.168.7.10 sport=2001 dport=1234 [ASSURED]
[..]
-> nat altered source ports to 1024 and 1025, respectively.
This can also be confirmed on destination host which shows
ESTAB 0 0 192.168.7.1:2000 192.168.7.10:1024
ESTAB 0 0 192.168.7.1:2000 192.168.7.10:1025
ESTAB 0 0 192.168.7.1:2000 192.168.7.10:1234
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Fixes: 870190a9ec907 ("netfilter: nat: convert nat bysrc hash to rhashtable")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The hci_get_route() API is used to look up local HCI devices, however
so far it has been incapable of dealing with anything else than the
public address of HCI devices. This completely breaks with LE-only HCI
devices that do not come with a public address, but use a static
random address instead.
This patch exteds the hci_get_route() API with a src_type parameter
that's used for comparing with the right address of each HCI device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The argument to get_net_ns_by_fd() is a /proc/$PID/ns/net file
descriptor not a pid. Fix the typo.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Rami Rosen <roszenrami@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch that removed the FIB offload infrastructure was a bit too
aggressive and also removed code needed to clean up us splitting the table
if additional rules were added. Specifically the function
fib_trie_flush_external was called at the end of a new rule being added to
flush the foreign trie entries from the main trie.
I updated the code so that we only call fib_trie_flush_external on the main
table so that we flush the entries for local from main. This way we don't
call it for every rule change which is what was happening previously.
Fixes: 347e3b28c1ba2 ("switchdev: remove FIB offload infrastructure")
Reported-by: Eric Dumazet <edumazet@google.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rolf Neugebauer reported very long delays at netns dismantle.
Eric W. Biederman was kind enough to look at this problem
and noticed synchronize_net() occurring from netif_napi_del() that was
added in linux-4.5
Busy polling makes no sense for tunnels NAPI.
If busy poll is used for sessions over tunnels, the poller will need to
poll the physical device queue anyway.
netif_tx_napi_add() could be used here, but function name is misleading,
and renaming it is not stable material, so set NAPI_STATE_NO_BUSY_POLL
bit directly.
This will avoid inserting gro_cells napi structures in napi_hash[]
and avoid the problematic synchronize_net() (per possible cpu) that
Rolf reported.
Fixes: 93d05d4a320c ("net: provide generic busy polling to all NAPI drivers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With syzkaller help, Marco Grassi found a bug in TCP stack,
crashing in tcp_collapse()
Root cause is that sk_filter() can truncate the incoming skb,
but TCP stack was not really expecting this to happen.
It probably was expecting a simple DROP or ACCEPT behavior.
We first need to make sure no part of TCP header could be removed.
Then we need to adjust TCP_SKB_CB(skb)->end_seq
Many thanks to syzkaller team and Marco for giving us a reproducer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Marco Grassi <marco.gra@gmail.com>
Reported-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains a larger than usual batch of Netfilter
fixes for your net tree. This series contains a mixture of old bugs and
recently introduced bugs, they are:
1) Fix a crash when using nft_dynset with nft_set_rbtree, which doesn't
support the set element updates from the packet path. From Liping
Zhang.
2) Fix leak when nft_expr_clone() fails, from Liping Zhang.
3) Fix a race when inserting new elements to the set hash from the
packet path, also from Liping.
4) Handle segmented TCP SIP packets properly, basically avoid that the
INVITE in the allow header create bogus expectations by performing
stricter SIP message parsing, from Ulrich Weber.
5) nft_parse_u32_check() should return signed integer for errors, from
John Linville.
6) Fix wrong allocation instead of connlabels, allocate 16 instead of
32 bytes, from Florian Westphal.
7) Fix compilation breakage when building the ip_vs_sync code with
CONFIG_OPTIMIZE_INLINING on x86, from Arnd Bergmann.
8) Destroy the new set if the transaction object cannot be allocated,
also from Liping Zhang.
9) Use device to route duplicated packets via nft_dup only when set by
the user, otherwise packets may not follow the right route, again
from Liping.
10) Fix wrong maximum genetlink attribute definition in IPVS, from
WANG Cong.
11) Ignore untracked conntrack objects from xt_connmark, from Florian
Westphal.
12) Allow to use conntrack helpers that are registered NFPROTO_UNSPEC
via CT target, otherwise we cannot use the h.245 helper, from
Florian.
13) Revisit garbage collection heuristic in the new workqueue-based
timer approach for conntrack to evict objects earlier, again from
Florian.
14) Fix crash in nf_tables when inserting an element into a verdict map,
from Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrey Konovalov reported following error while fuzzing with syzkaller :
IPv4: Attempt to release alive inet socket ffff880068e98940
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 1 PID: 3905 Comm: a.out Not tainted 4.9.0-rc3+ #333
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff88006b9e0000 task.stack: ffff880068770000
RIP: 0010:[<ffffffff819ead5f>] [<ffffffff819ead5f>]
selinux_socket_sock_rcv_skb+0xff/0x6a0 security/selinux/hooks.c:4639
RSP: 0018:ffff8800687771c8 EFLAGS: 00010202
RAX: ffff88006b9e0000 RBX: 1ffff1000d0eee3f RCX: 1ffff1000d1d312a
RDX: 1ffff1000d1d31a6 RSI: dffffc0000000000 RDI: 0000000000000010
RBP: ffff880068777360 R08: 0000000000000000 R09: 0000000000000002
R10: dffffc0000000000 R11: 0000000000000006 R12: ffff880068e98940
R13: 0000000000000002 R14: ffff880068777338 R15: 0000000000000000
FS: 00007f00ff760700(0000) GS:ffff88006cd00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020008000 CR3: 000000006a308000 CR4: 00000000000006e0
Stack:
ffff8800687771e0 ffffffff812508a5 ffff8800686f3168 0000000000000007
ffff88006ac8cdfc ffff8800665ea500 0000000041b58ab3 ffffffff847b5480
ffffffff819eac60 ffff88006b9e0860 ffff88006b9e0868 ffff88006b9e07f0
Call Trace:
[<ffffffff819c8dd5>] security_sock_rcv_skb+0x75/0xb0 security/security.c:1317
[<ffffffff82c2a9e7>] sk_filter_trim_cap+0x67/0x10e0 net/core/filter.c:81
[<ffffffff82b81e60>] __sk_receive_skb+0x30/0xa00 net/core/sock.c:460
[<ffffffff838bbf12>] dccp_v4_rcv+0xdb2/0x1910 net/dccp/ipv4.c:873
[<ffffffff83069d22>] ip_local_deliver_finish+0x332/0xad0
net/ipv4/ip_input.c:216
[< inline >] NF_HOOK_THRESH ./include/linux/netfilter.h:232
[< inline >] NF_HOOK ./include/linux/netfilter.h:255
[<ffffffff8306abd2>] ip_local_deliver+0x1c2/0x4b0 net/ipv4/ip_input.c:257
[< inline >] dst_input ./include/net/dst.h:507
[<ffffffff83068500>] ip_rcv_finish+0x750/0x1c40 net/ipv4/ip_input.c:396
[< inline >] NF_HOOK_THRESH ./include/linux/netfilter.h:232
[< inline >] NF_HOOK ./include/linux/netfilter.h:255
[<ffffffff8306b82f>] ip_rcv+0x96f/0x12f0 net/ipv4/ip_input.c:487
[<ffffffff82bd9fb7>] __netif_receive_skb_core+0x1897/0x2a50 net/core/dev.c:4213
[<ffffffff82bdb19a>] __netif_receive_skb+0x2a/0x170 net/core/dev.c:4251
[<ffffffff82bdb493>] netif_receive_skb_internal+0x1b3/0x390 net/core/dev.c:4279
[<ffffffff82bdb6b8>] netif_receive_skb+0x48/0x250 net/core/dev.c:4303
[<ffffffff8241fc75>] tun_get_user+0xbd5/0x28a0 drivers/net/tun.c:1308
[<ffffffff82421b5a>] tun_chr_write_iter+0xda/0x190 drivers/net/tun.c:1332
[< inline >] new_sync_write fs/read_write.c:499
[<ffffffff8151bd44>] __vfs_write+0x334/0x570 fs/read_write.c:512
[<ffffffff8151f85b>] vfs_write+0x17b/0x500 fs/read_write.c:560
[< inline >] SYSC_write fs/read_write.c:607
[<ffffffff81523184>] SyS_write+0xd4/0x1a0 fs/read_write.c:599
[<ffffffff83fc02c1>] entry_SYSCALL_64_fastpath+0x1f/0xc2
It turns out DCCP calls __sk_receive_skb(), and this broke when
lookups no longer took a reference on listeners.
Fix this issue by adding a @refcounted parameter to __sk_receive_skb(),
so that sock_put() is used only when needed.
Fixes: 3b24d854cb35 ("tcp/dccp: do not touch listener sk_refcnt under synflood")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some configurations (e.g. geneve interface with default
MTU of 1500 over an ethernet interface with 1500 MTU) result
in the transmission of packets that exceed the configured MTU.
While this should be considered to be a "bad" configuration,
it is still allowed and should not result in the sending
of packets that exceed the configured MTU.
Fix by dropping the assumption in ip_finish_output_gso() that
locally originated gso packets will never need fragmentation.
Basic testing using iperf (observing CPU usage and bandwidth)
have shown no measurable performance impact for traffic not
requiring fragmentation.
Fixes: c7ba65d7b649 ("net: ip: push gso skb forwarding handling down the stack")
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrey reported the following error report while running the syzkaller
fuzzer:
general protection fault: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 0 PID: 648 Comm: syz-executor Not tainted 4.9.0-rc3+ #333
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff8800398c4480 task.stack: ffff88003b468000
RIP: 0010:[<ffffffff83091106>] [< inline >]
inet_exact_dif_match include/net/tcp.h:808
RIP: 0010:[<ffffffff83091106>] [<ffffffff83091106>]
__inet_lookup_listener+0xb6/0x500 net/ipv4/inet_hashtables.c:219
RSP: 0018:ffff88003b46f270 EFLAGS: 00010202
RAX: 0000000000000004 RBX: 0000000000004242 RCX: 0000000000000001
RDX: 0000000000000000 RSI: ffffc90000e3c000 RDI: 0000000000000054
RBP: ffff88003b46f2d8 R08: 0000000000004000 R09: ffffffff830910e7
R10: 0000000000000000 R11: 000000000000000a R12: ffffffff867fa0c0
R13: 0000000000004242 R14: 0000000000000003 R15: dffffc0000000000
FS: 00007fb135881700(0000) GS:ffff88003ec00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020cc3000 CR3: 000000006d56a000 CR4: 00000000000006f0
Stack:
0000000000000000 000000000601a8c0 0000000000000000 ffffffff00004242
424200003b9083c2 ffff88003def4041 ffffffff84e7e040 0000000000000246
ffff88003a0911c0 0000000000000000 ffff88003a091298 ffff88003b9083ae
Call Trace:
[<ffffffff831100f4>] tcp_v4_send_reset+0x584/0x1700 net/ipv4/tcp_ipv4.c:643
[<ffffffff83115b1b>] tcp_v4_rcv+0x198b/0x2e50 net/ipv4/tcp_ipv4.c:1718
[<ffffffff83069d22>] ip_local_deliver_finish+0x332/0xad0
net/ipv4/ip_input.c:216
...
MD5 has a code path that calls __inet_lookup_listener with a null skb,
so inet{6}_exact_dif_match needs to check skb against null before pulling
the flag.
Fixes: a04a480d4392 ("net: Require exact match for TCP socket lookups if
dif is l3mdev")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb->cb may contain data from previous layers. In the observed scenario,
the garbage data were misinterpreted as IP6CB(skb)->frag_max_size, so
that small packets sent through the tunnel are mistakenly fragmented.
This patch unconditionally clears the control buffer in ip6tunnel_xmit(),
which affects ip6_tunnel, ip6_udp_tunnel and ip6_gre. Currently none of
these tunnels set IP6CB(skb)->flags, otherwise it needs to be done earlier.
Cc: stable@vger.kernel.org
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to this patch, in rx path, before calling lock_sock, it needed to
hold assoc when got it by __sctp_lookup_association, in case other place
would free/put assoc.
But in __sctp_lookup_association, it lookup and hold transport, then got
assoc by transport->assoc, then hold assoc and put transport. It means
it didn't hold transport, yet it was returned and later on directly
assigned to chunk->transport.
Without the protection of sock lock, the transport may be freed/put by
other places, which would cause a use-after-free issue.
This patch is to fix this issue by holding transport instead of assoc.
As holding transport can make sure to access assoc is also safe, and
actually it looks up assoc by searching transport rhashtable, to hold
transport here makes more sense.
Note that the function will be renamed later on on another patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
|
|
When vxlan device is closed vxlan socket is freed. This
operation can race with vxlan-xmit function which
dereferences vxlan socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just two fixes:
* a fix to process all events while suspending, so any
potential calls into the driver are done before it is
suspended
* small markup fixes for the sphinx documentation conversion
that's coming into the tree via the doc tree
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to IPv4, do not consider link state when validating next hops.
Currently, if the link is down default routes can fail to insert:
$ ip -6 ro add vrf blue default via 2100:2::64 dev eth2
RTNETLINK answers: No route to host
With this patch the command succeeds.
Fixes: 8c14586fc320 ("net: ipv6: Use passed in table for nexthop lookups")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rt6_add_route_info and rt6_add_dflt_router were updated to pull the FIB
table from the device index, but the corresponding rt6_get_route_info
and rt6_get_dflt_router functions were not leading to the failure to
process RA's:
ICMPv6: RA: ndisc_router_discovery failed to add default route
Fix the 'get' functions by using the table id associated with the
device when applicable.
Also, now that default routes can be added to tables other than the
default table, rt6_purge_dflt_routers needs to be updated as well to
look at all tables. To handle that efficiently, add a flag to the table
denoting if it is has a default route via RA.
Fixes: ca254490c8dfd ("net: Add VRF support to IPv6 stack")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is now a fixed-size extension, so we don't need to pass a variable
alloc size. This (harmless) error results in allocating 32 instead of
the needed 16 bytes for this extension as the size gets passed twice.
Fixes: 23014011ba420 ("netfilter: conntrack: support a fixed size of 128 distinct labels")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
nft_parse_u32_check
Commit 36b701fae12ac ("netfilter: nf_tables: validate maximum value of
u32 netlink attributes") introduced nft_parse_u32_check with a return
value of "unsigned int", yet on error it returns "-ERANGE".
This patch corrects the mismatch by changing the return value to "int",
which happens to match the actual users of nft_parse_u32_check already.
Found by Coverity, CID 1373930.
Note that commit 21a9e0f1568ea ("netfilter: nft_exthdr: fix error
handling in nft_exthdr_init()) attempted to address the issue, but
did not address the return type of nft_parse_u32_check.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Laura Garcia Liebana <nevola@gmail.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 36b701fae12ac ("netfilter: nf_tables: validate maximum value...")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When nft_expr_clone failed, a series of problems will happen:
1. module refcnt will leak, we call __module_get at the beginning but
we forget to put it back if ops->clone returns fail
2. memory will be leaked, if clone fail, we just return NULL and forget
to free the alloced element
3. set->nelems will become incorrect when set->size is specified. If
clone fail, we should decrease the set->nelems
Now this patch fixes these problems. And fortunately, clone fail will
only happen on counter expression when memory is exhausted.
Fixes: 086f332167d6 ("netfilter: nf_tables: add clone interface to expression operations")
Signed-off-by: Liping Zhang <zlpnobody@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
First bug was added in commit ad6f939ab193 ("ip: Add offset parameter to
ip_cmsg_recv") : Tom missed that ipv4 udp messages could be received on
AF_INET6 socket. ip_cmsg_recv(msg, skb) should have been replaced by
ip_cmsg_recv_offset(msg, skb, sizeof(struct udphdr));
Then commit e6afc8ace6dd ("udp: remove headers from UDP packets before
queueing") forgot to adjust the offsets now UDP headers are pulled
before skb are put in receive queue.
Fixes: ad6f939ab193 ("ip: Add offset parameter to ip_cmsg_recv")
Fixes: e6afc8ace6dd ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sam Kumar <samanthakumar@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skbuff and sock structure both had missing parameter annotation
values.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Baozeng reported this deadlock case:
CPU0 CPU1
---- ----
lock([ 165.136033] sk_lock-AF_INET6);
lock([ 165.136033] rtnl_mutex);
lock([ 165.136033] sk_lock-AF_INET6);
lock([ 165.136033] rtnl_mutex);
Similar to commit 87e9f0315952
("ipv4: fix a potential deadlock in mcast getsockopt() path")
this is due to we still have a case, ipv6_sock_mc_close(),
where we acquire sk_lock before rtnl_lock. Close this deadlock
with the similar solution, that is always acquire rtnl lock first.
Fixes: baf606d9c9b1 ("ipv4,ipv6: grab rtnl before locking the socket")
Reported-by: Baozeng Ding <sploving1@gmail.com>
Tested-by: Baozeng Ding <sploving1@gmail.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Baozeng Ding reported KASAN traces showing uses after free in
udp_lib_get_port() and other related UDP functions.
A CONFIG_DEBUG_PAGEALLOC=y kernel would eventually crash.
I could write a reproducer with two threads doing :
static int sock_fd;
static void *thr1(void *arg)
{
for (;;) {
connect(sock_fd, (const struct sockaddr *)arg,
sizeof(struct sockaddr_in));
}
}
static void *thr2(void *arg)
{
struct sockaddr_in unspec;
for (;;) {
memset(&unspec, 0, sizeof(unspec));
connect(sock_fd, (const struct sockaddr *)&unspec,
sizeof(unspec));
}
}
Problem is that udp_disconnect() could run without holding socket lock,
and this was causing list corruptions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Baozeng Ding <sploving1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
This is relatively small, mostly to get the SG/crypto
from stack removal fix that crashes things when VMAP
stack is used in conjunction with software crypto.
Aside from that, we have:
* a fix for AP_VLAN usage with the nl80211 frame command
* two fixes (and two preparation patches) for A-MSDU, one
to discard group-addressed (multicast) and unexpected
4-address A-MSDUs, the other to validate A-MSDU inner
MAC addresses properly to prevent controlled port bypass
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, socket lookups for l3mdev (vrf) use cases can match a socket
that is bound to a port but not a device (ie., a global socket). If the
sysctl tcp_l3mdev_accept is not set this leads to ack packets going out
based on the main table even though the packet came in from an L3 domain.
The end result is that the connection does not establish creating
confusion for users since the service is running and a socket shows in
ss output. Fix by requiring an exact dif to sk_bound_dev_if match if the
skb came through an interface enslaved to an l3mdev device and the
tcp_l3mdev_accept is not set.
skb's through an l3mdev interface are marked by setting a flag in
inet{6}_skb_parm. The IPv6 variant is already set; this patch adds the
flag for IPv4. Using an skb flag avoids a device lookup on the dif. The
flag is set in the VRF driver using the IP{6}CB macros. For IPv4, the
inet_skb_parm struct is moved in the cb per commit 971f10eca186, so the
match function in the TCP stack needs to use TCP_SKB_CB. For IPv6, the
move is done after the socket lookup, so IP6CB is used.
The flags field in inet_skb_parm struct needs to be increased to add
another flag. There is currently a 1-byte hole following the flags,
so it can be expanded to u16 without increasing the size of the struct.
Fixes: 193125dbd8eb ("net: Introduce VRF device driver")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull one more documentation update from Jonathan Corbet:
"A single commit converting the mac80211 DocBook template over to
Sphinx. Only 32 more to go..."
* tag 'docs-4.9-2' of git://git.lwn.net/linux:
docs-rst: sphinxify 802.11 documentation
|
|
The IPv6 temporary address generation uses a variable called DESYNC_FACTOR
to prevent hosts updating the addresses at the same time. Quoting RFC 4941:
... The value DESYNC_FACTOR is a random value (different for each
client) that ensures that clients don't synchronize with each other and
generate new addresses at exactly the same time ...
DESYNC_FACTOR is defined as:
DESYNC_FACTOR -- A random value within the range 0 - MAX_DESYNC_FACTOR.
It is computed once at system start (rather than each time it is used)
and must never be greater than (TEMP_VALID_LIFETIME - REGEN_ADVANCE).
First, I believe the RFC has a typo in it and meant to say: "and must
never be greater than (TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE)"
The reason is that at various places in the RFC, DESYNC_FACTOR is used in
a calculation like (TEMP_PREFERRED_LIFETIME - DESYNC_FACTOR) or
(TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE - DESYNC_FACTOR). It needs to be
smaller than (TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE) for the result of
these calculations to be larger than zero. It's never used in a
calculation together with TEMP_VALID_LIFETIME.
I already submitted an errata to the rfc-editor:
https://www.rfc-editor.org/errata_search.php?rfc=4941
The Linux implementation of DESYNC_FACTOR is very wrong:
max_desync_factor is used in places DESYNC_FACTOR should be used.
max_desync_factor is initialized to the RFC-recommended value for
MAX_DESYNC_FACTOR (600) but the whole point is to get a _random_ value.
And nothing ensures that the value used is not greater than
(TEMP_PREFERRED_LIFETIME - REGEN_ADVANCE), which leads to underflows. The
effect can easily be observed when setting the temp_prefered_lft sysctl
e.g. to 60. The preferred lifetime of the temporary addresses will be
bogus.
TEMP_PREFERRED_LIFETIME and REGEN_ADVANCE are not constants and can be
influenced by these three sysctls: regen_max_retry, dad_transmits and
temp_prefered_lft. Thus, the upper bound for desync_factor needs to be
re-calculated each time a new address is generated and if desync_factor is
larger than the new upper bound, a new random value needs to be
re-generated.
And since we already have max_desync_factor configurable per interface, we
also need to calculate and store desync_factor per interface.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The randomized interface identifier (rndid) was periodically updated from
the regen_timer timer. Simplify the code by updating the rndid only when
needed by ipv6_try_regen_rndid().
This makes the follow-up DESYNC_FACTOR fix much simpler. Also it fixes a
reference counting error in this error path, where an in6_dev_put was
missing:
err = addrconf_sysctl_register(ndev);
if (err) {
ipv6_mc_destroy_dev(ndev);
- del_timer(&ndev->regen_timer);
snmp6_unregister_dev(ndev);
goto err_release;
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Fix various build warnings in tlan/qed/xen-netback drivers, from
Arnd Bergmann.
2) Propagate proper error code in strparser's strp_recv(), from Geert
Uytterhoeven.
3) Fix accidental broadcast of RTM_GETTFILTER responses, from Eric
Dumazret.
4) Need to use list_for_each_entry_safe() in qed driver, from Wei
Yongjun.
5) Openvswitch 802.1AD bug fixes from Jiri Benc.
6) Cure BUILD_BUG_ON() in mlx5 driver, from Tom Herbert.
7) Fix UDP ipv6 checksumming in netvsc driver, from Stephen Hemminger.
8) stmmac driver fixes from Giuseppe CAVALLARO.
9) Fix access to mangled IP6CB in tcp, from Eric Dumazet.
10) Fix info leaks in tipc and rtnetlink, from Dan Carpenter.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
net: bridge: add the multicast_flood flag attribute to brport_attrs
net: axienet: Remove unused parameter from __axienet_device_reset
liquidio: CN23XX: fix a loop timeout
net: rtnl: info leak in rtnl_fill_vfinfo()
tipc: info leak in __tipc_nl_add_udp_addr()
net: ipv4: Do not drop to make_route if oif is l3mdev
net: phy: Trigger state machine on state change and not polling.
ipv6: tcp: restore IP6CB for pktoptions skbs
netvsc: Remove mistaken udp.h inclusion.
xen-netback: fix type mismatch warning
stmmac: fix error check when init ptp
stmmac: fix ptp init for gmac4
qed: fix old-style function definition
netvsc: fix checksum on UDP IPV6
net_sched: reorder pernet ops and act ops registrations
xen-netback: fix guest Rx stall detection (after guest Rx refactor)
drivers/ptp: Fix kernel memory disclosure
net/mlx5: Add MLX5_ARRAY_SET64 to fix BUILD_BUG_ON
qmi_wwan: add support for Quectel EC21 and EC25
openvswitch: add NETIF_F_HW_VLAN_STAG_TX to internal dev
...
|
|
Commit e0d56fdd7342 was a bit aggressive removing l3mdev calls in
the IPv4 stack. If the fib_lookup fails we do not want to drop to
make_route if the oif is an l3mdev device.
Also reverts 19664c6a0009 ("net: l3mdev: Remove netif_index_is_l3_master")
which removed netif_index_is_l3_master.
Fixes: e0d56fdd7342 ("net: l3mdev: remove redundant calls")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not accept arbitrary DA/SA inside A-MSDUs, it could be used
to circumvent protections, like allowing a station to send frames and
make them seem to come from somewhere else.
Add the necessary infrastructure in cfg80211 to allow such checks, in
further patches we'll start using them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's only a single case where has_80211_header is passed as true,
which is in mac80211. Given that there's only simple code that needs
to be done before calling it, export that function from cfg80211
instead and let mac80211 call it itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull uaccess.h prepwork from Al Viro:
"Preparations to tree-wide switch to use of linux/uaccess.h (which,
obviously, will allow to start unifying stuff for real). The last step
there, ie
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
`git grep -l "$PATT"|grep -v ^include/linux/uaccess.h`
is not taken here - I would prefer to do it once just before or just
after -rc1. However, everything should be ready for it"
* 'work.uaccess2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
remove a stray reference to asm/uaccess.h in docs
sparc64: separate extable_64.h, switch elf_64.h to it
score: separate extable.h, switch module.h to it
mips: separate extable.h, switch module.h to it
x86: separate extable.h, switch sections.h to it
remove stray include of asm/uaccess.h from cacheflush.h
mn10300: remove a bogus processor.h->uaccess.h include
xtensa: split uaccess.h into C and asm sides
bonding: quit messing with IOCTL
kill __kernel_ds_p off
mn10300: finish verify_area() off
frv: move HAVE_ARCH_UNMAPPED_AREA to pgtable.h
exceptions: detritus removal
|
|
This is just a very basic conversion, I've split up the original
multi-book template, and also split up the multi-part mac80211
part in the original book; neither of those were handled by the
automatic pandoc conversion.
Fix errors that showed up, resulting in a much nicer rendering,
at least for the interface combinations documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull namespace updates from Eric Biederman:
"This set of changes is a number of smaller things that have been
overlooked in other development cycles focused on more fundamental
change. The devpts changes are small things that were a distraction
until we managed to kill off DEVPTS_MULTPLE_INSTANCES. There is an
trivial regression fix to autofs for the unprivileged mount changes
that went in last cycle. A pair of ioctls has been added by Andrey
Vagin making it is possible to discover the relationships between
namespaces when referring to them through file descriptors.
The big user visible change is starting to add simple resource limits
to catch programs that misbehave. With namespaces in general and user
namespaces in particular allowing users to use more kinds of
resources, it has become important to have something to limit errant
programs. Because the purpose of these limits is to catch errant
programs the code needs to be inexpensive to use as it always on, and
the default limits need to be high enough that well behaved programs
on well behaved systems don't encounter them.
To this end, after some review I have implemented per user per user
namespace limits, and use them to limit the number of namespaces. The
limits being per user mean that one user can not exhause the limits of
another user. The limits being per user namespace allow contexts where
the limit is 0 and security conscious folks can remove from their
threat anlysis the code used to manage namespaces (as they have
historically done as it root only). At the same time the limits being
per user namespace allow other parts of the system to use namespaces.
Namespaces are increasingly being used in application sand boxing
scenarios so an all or nothing disable for the entire system for the
security conscious folks makes increasing use of these sandboxes
impossible.
There is also added a limit on the maximum number of mounts present in
a single mount namespace. It is nontrivial to guess what a reasonable
system wide limit on the number of mount structure in the kernel would
be, especially as it various based on how a system is using
containers. A limit on the number of mounts in a mount namespace
however is much easier to understand and set. In most cases in
practice only about 1000 mounts are used. Given that some autofs
scenarious have the potential to be 30,000 to 50,000 mounts I have set
the default limit for the number of mounts at 100,000 which is well
above every known set of users but low enough that the mount hash
tables don't degrade unreaonsably.
These limits are a start. I expect this estabilishes a pattern that
other limits for resources that namespaces use will follow. There has
been interest in making inotify event limits per user per user
namespace as well as interest expressed in making details about what
is going on in the kernel more visible"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (28 commits)
autofs: Fix automounts by using current_real_cred()->uid
mnt: Add a per mount namespace limit on the number of mounts
netns: move {inc,dec}_net_namespaces into #ifdef
nsfs: Simplify __ns_get_path
tools/testing: add a test to check nsfs ioctl-s
nsfs: add ioctl to get a parent namespace
nsfs: add ioctl to get an owning user namespace for ns file descriptor
kernel: add a helper to get an owning user namespace for a namespace
devpts: Change the owner of /dev/pts/ptmx to the mounter of /dev/pts
devpts: Remove sync_filesystems
devpts: Make devpts_kill_sb safe if fsi is NULL
devpts: Simplify devpts_mount by using mount_nodev
devpts: Move the creation of /dev/pts/ptmx into fill_super
devpts: Move parse_mount_options into fill_super
userns: When the per user per user namespace limit is reached return ENOSPC
userns; Document per user per user namespace limits.
mntns: Add a limit on the number of mount namespaces.
netns: Add a limit on the number of net namespaces
cgroupns: Add a limit on the number of cgroup namespaces
ipcns: Add a limit on the number of ipc namespaces
...
|
|
assignment"
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resolve the merge conflict between Felix's/my and Toke's patches
coming into the tree through net and mac80211-next respectively.
Most of Felix's changes go away due to Toke's new infrastructure
work, my patch changes to "goto begin" (the label wasn't there
before) instead of returning NULL so flow control towards drivers
is preserved better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
