| Age | Commit message (Collapse) | Author |
|---|
|
Add documentations and dt-bindings headers for the AO clock and reset
controller.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Pull more block fixes from Jens Axboe:
"As mentioned in the pull the other day, a few more fixes for this
round, all related to the bio op changes in this series.
Two fixes, and then a cleanup, renaming bio->bi_rw to bio->bi_opf. I
wanted to do that change right after or right before -rc1, so that
risk of conflict was reduced. I just rebased the series on top of
current master, and no new ->bi_rw usage has snuck in"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: rename bio bi_rw to bi_opf
target: iblock_execute_sync_cache() should use bio_set_op_attrs()
mm: make __swap_writepage() use bio_set_op_attrs()
block/mm: make bdev_ops->rw_page() take a bool for read/write
|
|
Pull drm zpos property support from Dave Airlie:
"This tree was waiting on some media stuff I hadn't had time to get a
stable branchpoint off, so I just waited until it was all in your tree
first.
It's been around a bit on the list and shouldn't affect anything
outside adding the generic API and moving some ARM drivers to using
it"
* tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux:
drm: rcar: use generic code for managing zpos plane property
drm/exynos: use generic code for managing zpos plane property
drm: sti: use generic zpos for plane
drm: add generic zpos property
|
|
Since commit 63a4cc24867d, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Commit abf545484d31 changed it from an 'rw' flags type to the
newer ops based interface, but now we're effectively leaking
some bdev internals to the rest of the kernel. Since we only
care about whether it's a read or a write at that level, just
pass in a bool 'is_write' parameter instead.
Then we can also move op_is_write() and friends back under
CONFIG_BLOCK protection.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more vfs updates from Al Viro:
"Assorted cleanups and fixes.
In the "trivial API change" department - ->d_compare() losing 'parent'
argument"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
cachefiles: Fix race between inactivating and culling a cache object
9p: use clone_fid()
9p: fix braino introduced in "9p: new helper - v9fs_parent_fid()"
vfs: make dentry_needs_remove_privs() internal
vfs: remove file_needs_remove_privs()
vfs: fix deadlock in file_remove_privs() on overlayfs
get rid of 'parent' argument of ->d_compare()
cifs, msdos, vfat, hfs+: don't bother with parent in ->d_compare()
affs ->d_compare(): don't bother with ->d_inode
fold _d_rehash() and __d_rehash() together
fold dentry_rcuwalk_invalidate() into its only remaining caller
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull qstr constification updates from Al Viro:
"Fairly self-contained bunch - surprising lot of places passes struct
qstr * as an argument when const struct qstr * would suffice; it
complicates analysis for no good reason.
I'd prefer to feed that separately from the assorted fixes (those are
in #for-linus and with somewhat trickier topology)"
* 'work.const-qstr' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
qstr: constify instances in adfs
qstr: constify instances in lustre
qstr: constify instances in f2fs
qstr: constify instances in ext2
qstr: constify instances in vfat
qstr: constify instances in procfs
qstr: constify instances in fuse
qstr constify instances in fs/dcache.c
qstr: constify instances in nfs
qstr: constify instances in ocfs2
qstr: constify instances in autofs4
qstr: constify instances in hfs
qstr: constify instances in hfsplus
qstr: constify instances in logfs
qstr: constify dentry_init_security
|
|
Pull virtio/vhost updates from Michael Tsirkin:
- new vsock device support in host and guest
- platform IOMMU support in host and guest, including compatibility
quirks for legacy systems.
- misc fixes and cleanups.
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
VSOCK: Use kvfree()
vhost: split out vringh Kconfig
vhost: detect 32 bit integer wrap around
vhost: new device IOTLB API
vhost: drop vringh dependency
vhost: convert pre sorted vhost memory array to interval tree
vhost: introduce vhost memory accessors
VSOCK: Add Makefile and Kconfig
VSOCK: Introduce vhost_vsock.ko
VSOCK: Introduce virtio_transport.ko
VSOCK: Introduce virtio_vsock_common.ko
VSOCK: defer sock removal to transports
VSOCK: transport-specific vsock_transport functions
vhost: drop vringh dependency
vop: pull in vhost Kconfig
virtio: new feature to detect IOMMU device quirk
balloon: check the number of available pages in leak balloon
vhost: lockless enqueuing
vhost: simplify work flushing
|
|
Pull more KVM updates from Paolo Bonzini:
- ARM bugfix and MSI injection support
- x86 nested virt tweak and OOPS fix
- Simplify pvclock code (vdso bits acked by Andy Lutomirski).
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
nvmx: mark ept single context invalidation as supported
nvmx: remove comment about missing nested vpid support
KVM: lapic: fix access preemption timer stuff even if kernel_irqchip=off
KVM: documentation: fix KVM_CAP_X2APIC_API information
x86: vdso: use __pvclock_read_cycles
pvclock: introduce seqcount-like API
arm64: KVM: Set cpsr before spsr on fault injection
KVM: arm: vgic-irqfd: Workaround changing kvm_set_routing_entry prototype
KVM: arm/arm64: Enable MSI routing
KVM: arm/arm64: Enable irqchip routing
KVM: Move kvm_setup_default/empty_irq_routing declaration in arch specific header
KVM: irqchip: Convey devid to kvm_set_msi
KVM: Add devid in kvm_kernel_irq_routing_entry
KVM: api: Pass the devid in the msi routing entry
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes improve some aspects of the atomic API as well as
make use of this new API in the regulator framework to allow properly
dealing with critical regulators controlled by a PWM.
Aside from that there's a bunch of updates and cleanups for existing
drivers, as well as the addition of new drivers for the Broadcom
iProc, STMPE and ChromeOS EC controllers"
* tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
regulator: pwm: Document pwm-dutycycle-unit and pwm-dutycycle-range
regulator: pwm: Support extra continuous mode cases
pwm: Add ChromeOS EC PWM driver
dt-bindings: pwm: Add binding for ChromeOS EC PWM
mfd: cros_ec: Add EC_PWM function definitions
mfd: cros_ec: Add cros_ec_cmd_xfer_status() helper
pwm: atmel: Use of_device_get_match_data()
pwm: atmel: Fix checkpatch warnings
pwm: atmel: Fix disabling of PWM channels
dt-bindings: pwm: Add R-Car H3 device tree bindings
pwm: rcar: Use ARCH_RENESAS
pwm: tegra: Add support for Tegra186
dt-bindings: pwm: tegra: Add compatible string for Tegra186
pwm: tegra: Avoid overflow when calculating duty cycle
pwm: tegra: Allow 100 % duty cycle
pwm: tegra: Add support for reset control
pwm: tegra: Rename mmio_base to regs
pwm: tegra: Remove useless padding
pwm: tegra: Drop NUM_PWM macro
pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value
...
|
|
Pull block fixes from Jens Axboe:
"Here's the second round of block updates for this merge window.
It's a mix of fixes for changes that went in previously in this round,
and fixes in general. This pull request contains:
- Fixes for loop from Christoph
- A bdi vs gendisk lifetime fix from Dan, worth two cookies.
- A blk-mq timeout fix, when on frozen queues. From Gabriel.
- Writeback fix from Jan, ensuring that __writeback_single_inode()
does the right thing.
- Fix for bio->bi_rw usage in f2fs from me.
- Error path deadlock fix in blk-mq sysfs registration from me.
- Floppy O_ACCMODE fix from Jiri.
- Fix to the new bio op methods from Mike.
One more followup will be coming here, ensuring that we don't
propagate the block types outside of block. That, and a rename of
bio->bi_rw is coming right after -rc1 is cut.
- Various little fixes"
* 'for-linus' of git://git.kernel.dk/linux-block:
mm/block: convert rw_page users to bio op use
loop: make do_req_filebacked more robust
loop: don't try to use AIO for discards
blk-mq: fix deadlock in blk_mq_register_disk() error path
Include: blkdev: Removed duplicate 'struct request;' declaration.
Fixup direct bi_rw modifiers
block: fix bdi vs gendisk lifetime mismatch
blk-mq: Allow timeouts to run while queue is freezing
nbd: fix race in ioctl
block: fix use-after-free in seq file
f2fs: drop bio->bi_rw manual assignment
block: add missing group association in bio-cloning functions
blkcg: kill unused field nr_undestroyed_grps
writeback: Write dirty times for WB_SYNC_ALL writeback
floppy: fix open(O_ACCMODE) for ioctl-only open
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
"Two new drivers for touchscreen controllers:
- Silead touchscreen controllers
- SiS 9200 family touchscreen controllers
and a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: silead - remove some dead code
Input: sis-i2c - select CONFIG_CRC_ITU_T
Input: add driver for SiS 9200 family I2C touchscreen controllers
Input: ili210x - fix permissions on "calibrate" attribute
Input: elan_i2c - properly wake up touchpad on ASUS laptops
Input: add driver for Silead touchscreens
Input: elantech - fix debug dump of the current packet
Input: rotary_encoder - support binary encoding of states
Input: xpad - power off wireless 360 controllers on suspend
Input: i8042 - break load dependency between atkbd/psmouse and i8042
Input: synaptics-rmi4 - do not check for NULL when calling of_node_put()
Input: cros_ec_keyb - cleanup use of dev
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"RTC for 4.8
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup
rtc-cmos, rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after
shutdown for QNAP TS-41x
- s3c: clock fixes"
* tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (65 commits)
rtc: rv8803: Clear V1F when setting the time
rtc: rv8803: Stop the clock while setting the time
rtc: rv8803: Always apply the I²C workaround
rtc: rv8803: Fix read day of week
rtc: rv8803: Remove the check for valid time
rtc: rv8803: Kconfig: Indicate rx8900 support
rtc: asm9260: remove .owner field for driver
rtc: at91sam9: Fix missing spin_lock_init()
rtc: m41t80: add suspend handlers for alarm IRQ
rtc: m41t80: make it a real error message
rtc: pcf85063: Add support for the PCF85063A device
rtc: pcf85063: fix year range
rtc: hym8563: in .read_alarm set .tm_sec to 0 to signal minute accuracy
rtc: explicitly set tm_sec = 0 for drivers with minute accurancy
rtc: s3c: Add s3c_rtc_{enable/disable}_clk in s3c_rtc_setfreq()
rtc: s3c: Remove unnecessary call to disable already disabled clock
rtc: abx80x: use devm_add_action_or_reset()
rtc: m41t80: use devm_add_action_or_reset()
rtc: fix a typo and reduce three empty lines to one
rtc: s35390a: improve two comments in .set_alarm
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"These were delayed for various reasons, so I let them sit in next a
bit longer, rather than including them in my first pull request.
Fixes:
- Fix early access to cpu_spec relocation from Benjamin Herrenschmidt
- Fix incorrect event codes in power9-event-list from Madhavan Srinivasan
- Move register_process_table() out of ppc_md from Michael Ellerman
Use jump_label use for [cpu|mmu]_has_feature():
- Add mmu_early_init_devtree() from Michael Ellerman
- Move disable_radix handling into mmu_early_init_devtree() from Michael Ellerman
- Do hash device tree scanning earlier from Michael Ellerman
- Do radix device tree scanning earlier from Michael Ellerman
- Do feature patching before MMU init from Michael Ellerman
- Check features don't change after patching from Michael Ellerman
- Make MMU_FTR_RADIX a MMU family feature from Aneesh Kumar K.V
- Convert mmu_has_feature() to returning bool from Michael Ellerman
- Convert cpu_has_feature() to returning bool from Michael Ellerman
- Define radix_enabled() in one place & use static inline from Michael Ellerman
- Add early_[cpu|mmu]_has_feature() from Michael Ellerman
- Convert early cpu/mmu feature check to use the new helpers from Aneesh Kumar K.V
- jump_label: Make it possible for arches to invoke jump_label_init() earlier from Kevin Hao
- Call jump_label_init() in apply_feature_fixups() from Aneesh Kumar K.V
- Remove mfvtb() from Kevin Hao
- Move cpu_has_feature() to a separate file from Kevin Hao
- Add kconfig option to use jump labels for cpu/mmu_has_feature() from Michael Ellerman
- Add option to use jump label for cpu_has_feature() from Kevin Hao
- Add option to use jump label for mmu_has_feature() from Kevin Hao
- Catch usage of cpu/mmu_has_feature() before jump label init from Aneesh Kumar K.V
- Annotate jump label assembly from Michael Ellerman
TLB flush enhancements from Aneesh Kumar K.V:
- radix: Implement tlb mmu gather flush efficiently
- Add helper for finding SLBE LLP encoding
- Use hugetlb flush functions
- Drop multiple definition of mm_is_core_local
- radix: Add tlb flush of THP ptes
- radix: Rename function and drop unused arg
- radix/hugetlb: Add helper for finding page size
- hugetlb: Add flush_hugetlb_tlb_range
- remove flush_tlb_page_nohash
Add new ptrace regsets from Anshuman Khandual and Simon Guo:
- elf: Add powerpc specific core note sections
- Add the function flush_tmregs_to_thread
- Enable in transaction NT_PRFPREG ptrace requests
- Enable in transaction NT_PPC_VMX ptrace requests
- Enable in transaction NT_PPC_VSX ptrace requests
- Adapt gpr32_get, gpr32_set functions for transaction
- Enable support for NT_PPC_CGPR
- Enable support for NT_PPC_CFPR
- Enable support for NT_PPC_CVMX
- Enable support for NT_PPC_CVSX
- Enable support for TM SPR state
- Enable NT_PPC_TM_CTAR, NT_PPC_TM_CPPR, NT_PPC_TM_CDSCR
- Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR
- Enable support for EBB registers
- Enable support for Performance Monitor registers"
* tag 'powerpc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (48 commits)
powerpc/mm: Move register_process_table() out of ppc_md
powerpc/perf: Fix incorrect event codes in power9-event-list
powerpc/32: Fix early access to cpu_spec relocation
powerpc/ptrace: Enable support for Performance Monitor registers
powerpc/ptrace: Enable support for EBB registers
powerpc/ptrace: Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR
powerpc/ptrace: Enable NT_PPC_TM_CTAR, NT_PPC_TM_CPPR, NT_PPC_TM_CDSCR
powerpc/ptrace: Enable support for TM SPR state
powerpc/ptrace: Enable support for NT_PPC_CVSX
powerpc/ptrace: Enable support for NT_PPC_CVMX
powerpc/ptrace: Enable support for NT_PPC_CFPR
powerpc/ptrace: Enable support for NT_PPC_CGPR
powerpc/ptrace: Adapt gpr32_get, gpr32_set functions for transaction
powerpc/ptrace: Enable in transaction NT_PPC_VSX ptrace requests
powerpc/ptrace: Enable in transaction NT_PPC_VMX ptrace requests
powerpc/ptrace: Enable in transaction NT_PRFPREG ptrace requests
powerpc/process: Add the function flush_tmregs_to_thread
elf: Add powerpc specific core note sections
powerpc/mm: remove flush_tlb_page_nohash
powerpc/mm/hugetlb: Add flush_hugetlb_tlb_range
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull second round of rdma updates from Doug Ledford:
"This can be split out into just two categories:
- fixes to the RDMA R/W API in regards to SG list length limits
(about 5 patches)
- fixes/features for the Intel hfi1 driver (everything else)
The hfi1 driver is still being brought to full feature support by
Intel, and they have a lot of people working on it, so that amounts to
almost the entirety of this pull request"
* tag 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (84 commits)
IB/hfi1: Add cache evict LRU list
IB/hfi1: Fix memory leak during unexpected shutdown
IB/hfi1: Remove unneeded mm argument in remove function
IB/hfi1: Consistently call ops->remove outside spinlock
IB/hfi1: Use evict mmu rb operation
IB/hfi1: Add evict operation to the mmu rb handler
IB/hfi1: Fix TID caching actions
IB/hfi1: Make the cache handler own its rb tree root
IB/hfi1: Make use of mm consistent
IB/hfi1: Fix user SDMA racy user request claim
IB/hfi1: Fix error condition that needs to clean up
IB/hfi1: Release node on insert failure
IB/hfi1: Validate SDMA user iovector count
IB/hfi1: Validate SDMA user request index
IB/hfi1: Use the same capability state for all shared contexts
IB/hfi1: Prevent null pointer dereference
IB/hfi1: Rename TID mmu_rb_* functions
IB/hfi1: Remove unneeded empty check in hfi1_mmu_rb_unregister()
IB/hfi1: Restructure hfi1_file_open
IB/hfi1: Make iovec loop index easy to understand
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull base rdma updates from Doug Ledford:
"Round one of 4.8 code: while this is mostly normal, there is a new
driver in here (the driver was hosted outside the kernel for several
years and is actually a fairly mature and well coded driver). It
amounts to 13,000 of the 16,000 lines of added code in here.
Summary:
- Updates/fixes for iw_cxgb4 driver
- Updates/fixes for mlx5 driver
- Add flow steering and RSS API
- Add hardware stats to mlx4 and mlx5 drivers
- Add firmware version API for RDMA driver use
- Add the rxe driver (this is a software RoCE driver that makes any
Ethernet device a RoCE device)
- Fixes for i40iw driver
- Support for send only multicast joins in the cma layer
- Other minor fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (72 commits)
Soft RoCE driver
IB/core: Support for CMA multicast join flags
IB/sa: Add cached attribute containing SM information to SA port
IB/uverbs: Fix race between uverbs_close and remove_one
IB/mthca: Clean up error unwind flow in mthca_reset()
IB/mthca: NULL arg to pci_dev_put is OK
IB/hfi1: NULL arg to sc_return_credits is OK
IB/mlx4: Add diagnostic hardware counters
net/mlx4: Query performance and diagnostics counters
net/mlx4: Add diagnostic counters capability bit
Use smaller 512 byte messages for portmapper messages
IB/ipoib: Report SG feature regardless of HW UD CSUM capability
IB/mlx4: Don't use GFP_ATOMIC for CQ resize struct
IB/hfi1: Disable by default
IB/rdmavt: Disable by default
IB/mlx5: Fix port counter ID association to QP offset
IB/mlx5: Fix iteration overrun in GSI qps
i40iw: Add NULL check for puda buffer
i40iw: Change dup_ack_thresh to u8
i40iw: Remove unnecessary check for moving CQ head
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"The most notable item is IBM virtual SCSI target driver, that was
originally ported to target-core back in 2010 by Tomo-san, and has
been brought forward to v4.x code by Bryant Ly, Michael Cyr and co
over the last months.
Also included are two ORDERED task related bug-fixes Bryant + Michael
found along the way using ibmvscsis with AIX guests, plus a few
miscellaneous target-core + iscsi-target bug-fixes with associated
stable tags"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: fix spelling mistake: "limitiation" -> "limitation"
target: Fix residual overflow handling in target_complete_cmd_with_length
tcm_fc: set and unset FCP_SPPF_TARG_FCN
iscsi-target: Fix panic when adding second TCP connection to iSCSI session
ibmvscsis: Initial commit of IBM VSCSI Tgt Driver
target: Fix ordered task CHECK_CONDITION early exception handling
target: Fix ordered task target_setup_cmd_from_cdb exception hang
target: Fix max_unmap_lba_count calc overflow
target: Fix race between iscsi-target connection shutdown + ABORT_TASK
target: Fix missing complete during ABORT_TASK + CMD_T_FABRIC_STOP
|
|
Pull nfsd updates from Bruce Fields:
"Highlights:
- Trond made a change to the server's tcp logic that allows a fast
client to better take advantage of high bandwidth networks, but may
increase the risk that a single client could starve other clients;
a new sunrpc.svc_rpc_per_connection_limit parameter should help
mitigate this in the (hopefully unlikely) event this becomes a
problem in practice.
- Tom Haynes added a minimal flex-layout pnfs server, which is of no
use in production for now--don't build it unless you're doing
client testing or further server development"
* tag 'nfsd-4.8' of git://linux-nfs.org/~bfields/linux: (32 commits)
nfsd: remove some dead code in nfsd_create_locked()
nfsd: drop unnecessary MAY_EXEC check from create
nfsd: clean up bad-type check in nfsd_create_locked
nfsd: remove unnecessary positive-dentry check
nfsd: reorganize nfsd_create
nfsd: check d_can_lookup in fh_verify of directories
nfsd: remove redundant zero-length check from create
nfsd: Make creates return EEXIST instead of EACCES
SUNRPC: Detect immediate closure of accepted sockets
SUNRPC: accept() may return sockets that are still in SYN_RECV
nfsd: allow nfsd to advertise multiple layout types
nfsd: Close race between nfsd4_release_lockowner and nfsd4_lock
nfsd/blocklayout: Make sure calculate signature/designator length aligned
xfs: abstract block export operations from nfsd layouts
SUNRPC: Remove unused callback xpo_adjust_wspace()
SUNRPC: Change TCP socket space reservation
SUNRPC: Add a server side per-connection limit
SUNRPC: Micro optimisation for svc_data_ready
SUNRPC: Call the default socket callbacks instead of open coding
SUNRPC: lock the socket while detaching it
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull more btrfs updates from Chris Mason:
"This is part two of my btrfs pull, which is some cleanups and a batch
of fixes.
Most of the code here is from Jeff Mahoney, making the pointers we
pass around internally more consistent and less confusing overall. I
noticed a small problem right before I sent this out yesterday, so I
fixed it up and re-tested overnight"
* 'for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (40 commits)
Btrfs: fix __MAX_CSUM_ITEMS
btrfs: btrfs_abort_transaction, drop root parameter
btrfs: add btrfs_trans_handle->fs_info pointer
btrfs: btrfs_relocate_chunk pass extent_root to btrfs_end_transaction
btrfs: convert nodesize macros to static inlines
btrfs: introduce BTRFS_MAX_ITEM_SIZE
btrfs: cleanup, remove prototype for btrfs_find_root_ref
btrfs: copy_to_sk drop unused root parameter
btrfs: simpilify btrfs_subvol_inherit_props
btrfs: tests, use BTRFS_FS_STATE_DUMMY_FS_INFO instead of dummy root
btrfs: tests, require fs_info for root
btrfs: tests, move initialization into tests/
btrfs: btrfs_test_opt and friends should take a btrfs_fs_info
btrfs: prefix fsid to all trace events
btrfs: plumb fs_info into btrfs_work
btrfs: remove obsolete part of comment in statfs
btrfs: hide test-only member under ifdef
btrfs: Ratelimit "no csum found" info message
btrfs: Add ratelimit to btrfs printing
Btrfs: fix unexpected balance crash due to BUG_ON
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu updates from Greg Ungerer:
"This series is all about Nicolas flat format support for MMU systems.
Traditional m68k no-MMU flat format binaries can now be run on m68k
MMU enabled systems too. The series includes some nice cleanups of
the binfmt_flat code and converts it to using proper user space
accessor functions.
With all this in place you can boot and run a complete no-MMU flat
format based user space on an MMU enabled system"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: enable binfmt_flat on systems with an MMU
binfmt_flat: allow compressed flat binary format to work on MMU systems
binfmt_flat: add MMU-specific support
binfmt_flat: update libraries' data segment pointer with userspace accessors
binfmt_flat: use clear_user() rather than memset() to clear .bss
binfmt_flat: use proper user space accessors with old relocs code
binfmt_flat: use proper user space accessors with relocs processing code
binfmt_flat: clean up create_flat_tables() and stack accesses
binfmt_flat: use generic transfer_args_to_stack()
elf_fdpic_transfer_args_to_stack(): make it generic
binfmt_flat: prevent kernel dammage from corrupted executable headers
binfmt_flat: convert printk invocations to their modern form
binfmt_flat: assorted cleanups
m68k: use same start_thread() on MMU and no-MMU
m68k: fix file path comment
m68k: fix bFLT executable running on MMU enabled systems
|
|
The rw_page users were not converted to use bio/req ops. As a result
bdev_write_page is not passing down REQ_OP_WRITE and the IOs will
be sent down as reads.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixes: 4e1b2d52a80d ("block, fs, drivers: remove REQ_OP compat defs and related code")
Modified by me to:
1) Drop op_flags passing into ->rw_page(), as we don't use it.
2) Make op_is_write() and friends safe to use for !CONFIG_BLOCK
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
In include/linux/blkdev.h duplicate declarations of the request
struct exist. Cleaned up by removing the second, unneeded
declaration.
Signed-off-by: John Pittman <jpittman@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The name for a bdi of a gendisk is derived from the gendisk's devt.
However, since the gendisk is destroyed before the bdi it leaves a
window where a new gendisk could dynamically reuse the same devt while a
bdi with the same name is still live. Arrange for the bdi to hold a
reference against its "owner" disk device while it is registered.
Otherwise we can hit sysfs duplicate name collisions like the following:
WARNING: CPU: 10 PID: 2078 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x64/0x80
sysfs: cannot create duplicate filename '/devices/virtual/bdi/259:1'
Hardware name: HP ProLiant DL580 Gen8, BIOS P79 05/06/2015
0000000000000286 0000000002c04ad5 ffff88006f24f970 ffffffff8134caec
ffff88006f24f9c0 0000000000000000 ffff88006f24f9b0 ffffffff8108c351
0000001f0000000c ffff88105d236000 ffff88105d1031e0 ffff8800357427f8
Call Trace:
[<ffffffff8134caec>] dump_stack+0x63/0x87
[<ffffffff8108c351>] __warn+0xd1/0xf0
[<ffffffff8108c3cf>] warn_slowpath_fmt+0x5f/0x80
[<ffffffff812a0d34>] sysfs_warn_dup+0x64/0x80
[<ffffffff812a0e1e>] sysfs_create_dir_ns+0x7e/0x90
[<ffffffff8134faaa>] kobject_add_internal+0xaa/0x320
[<ffffffff81358d4e>] ? vsnprintf+0x34e/0x4d0
[<ffffffff8134ff55>] kobject_add+0x75/0xd0
[<ffffffff816e66b2>] ? mutex_lock+0x12/0x2f
[<ffffffff8148b0a5>] device_add+0x125/0x610
[<ffffffff8148b788>] device_create_groups_vargs+0xd8/0x100
[<ffffffff8148b7cc>] device_create_vargs+0x1c/0x20
[<ffffffff811b775c>] bdi_register+0x8c/0x180
[<ffffffff811b7877>] bdi_register_dev+0x27/0x30
[<ffffffff813317f5>] add_disk+0x175/0x4a0
Cc: <stable@vger.kernel.org>
Reported-by: Yi Zhang <yizhan@redhat.com>
Tested-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Fixed up missing 0 return in bdi_register_owner().
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
When a bio is cloned, the newly created bio must be associated with
the same blkcg as the original bio (if BLK_CGROUP is enabled). If
this operation is not performed, then the new bio is not associated
with any group, and the group of the current task is returned when
the group of the bio is requested.
Depending on the cloning frequency, this may cause a large
percentage of the bios belonging to a given group to be treated
as if belonging to other groups (in most cases as if belonging to
the root group). The expected group isolation may thereby be broken.
This commit adds the missing association in bio-cloning functions.
Fixes: da2f0f74cf7d ("Btrfs: add support for blkio controllers")
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Reviewed-by: Nikolay Borisov <kernel@kyup.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
Soft RoCE (RXE) - The software RoCE driver
ib_rxe implements the RDMA transport and registers to the RDMA core
device as a kernel verbs provider. It also implements the packet IO
layer. On the other hand ib_rxe registers to the Linux netdev stack
as a udp encapsulating protocol, in that case RDMA, for sending and
receiving packets over any Ethernet device. This yields a RDMA
transport over the UDP/Ethernet network layer forming a RoCEv2
compatible device.
The configuration procedure of the Soft RoCE drivers requires
binding to any existing Ethernet network device. This is done with
/sys interface.
A userspace Soft RoCE library (librxe) provides user applications
the ability to run with Soft RoCE devices. The use of rxe verbs ins
user space requires the inclusion of librxe as a device specifics
plug-in to libibverbs. librxe is packaged separately.
Architecture:
+-----------------------------------------------------------+
| Application |
+-----------------------------------------------------------+
+-----------------------------------+
| libibverbs |
User +-----------------------------------+
+----------------+ +----------------+
| librxe | | HW RoCE lib |
+----------------+ +----------------+
+---------------------------------------------------------------+
+--------------+ +------------+
| Sockets | | RDMA ULP |
+--------------+ +------------+
+--------------+ +---------------------+
| TCP/IP | | ib_core |
+--------------+ +---------------------+
+------------+ +----------------+
Kernel | ib_rxe | | HW RoCE driver |
+------------+ +----------------+
+------------------------------------+
| NIC driver |
+------------------------------------+
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+-----------------------------------------------------------+
| Application |
+-----------------------------------------------------------+
+-----------------------------------+
| libibverbs |
User +-----------------------------------+
+----------------+ +----------------+
| librxe | | HW RoCE lib |
+----------------+ +----------------+
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+--------------+ +------------+
| Sockets | | RDMA ULP |
+--------------+ +------------+
+--------------+ +---------------------+
| TCP/IP | | ib_core |
+--------------+ +---------------------+
+------------+ +----------------+
Kernel | ib_rxe | | HW RoCE driver |
+------------+ +----------------+
+------------------------------------+
| NIC driver |
+------------------------------------+
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Soft RoCE resources:
[1[ https://github.com/SoftRoCE/librxe-dev librxe - source code in
Github
[2] https://github.com/SoftRoCE/rxe-dev/wiki/rxe-dev:-Home - Soft RoCE
Wiki page
[3] https://github.com/SoftRoCE/librxe-dev - Soft RoCE userspace library
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"The only interesting thing here is Jessica's patch to add
ro_after_init support to modules. The rest are all trivia"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
extable.h: add stddef.h so "NULL" definition is not implicit
modules: add ro_after_init support
jump_label: disable preemption around __module_text_address().
exceptions: fork exception table content from module.h into extable.h
modules: Add kernel parameter to blacklist modules
module: Do a WARN_ON_ONCE() for assert module mutex not held
Documentation/module-signing.txt: Note need for version info if reusing a key
module: Invalidate signatures on force-loaded modules
module: Issue warnings when tainting kernel
module: fix redundant test.
module: fix noreturn attribute for __module_put_and_exit()
|
|
Although dynamic debug is often only used for debug builds, sometimes
its enabled for production builds as well. Minimize its impact by using
jump labels. This reduces the text section by 7000+ bytes in the kernel
image below. It does increase data, but this should only be referenced
when changing the direction of the branches, and hence usually not in
cache.
text data bss dec hex filename
8194852 4879776 925696 14000324 d5a0c4 vmlinux.pre
8187337 4960224 925696 14073257 d6bda9 vmlinux.post
Link: http://lkml.kernel.org/r/d165b465e8c89bc582d973758d40be44c33f018b.1467837322.git.jbaron@akamai.com
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The current jump_label.h includes bug.h for things such as WARN_ON().
This makes the header problematic for inclusion by kernel.h or any
headers that kernel.h includes, since bug.h includes kernel.h (circular
dependency). The inclusion of atomic.h is similarly problematic. Thus,
this should make jump_label.h 'includable' from most places.
Link: http://lkml.kernel.org/r/7060ce35ddd0d20b33bf170685e6b0fab816bdf2.1467837322.git.jbaron@akamai.com
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove two unneeded `else's.
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Changes for v4.8 - Take 2
Includes GSI routing support to go along with the new VGIC and a small fix that
has been cooking in -next for a while.
|
|
|
|
Added UCMA and CMA support for multicast join flags. Flags are
passed using UCMA CM join command previously reserved fields.
Currently supporting two join flags indicating two different
multicast JoinStates:
1. Full Member:
The initiator creates the Multicast group(MCG) if it wasn't
previously created, can send Multicast messages to the group
and receive messages from the MCG.
2. Send Only Full Member:
The initiator creates the Multicast group(MCG) if it wasn't
previously created, can send Multicast messages to the group
but doesn't receive any messages from the MCG.
IB: Send Only Full Member requires a query of ClassPortInfo
to determine if SM/SA supports this option. If SM/SA
doesn't support Send-Only there will be no join request
sent and an error will be returned.
ETH: When Send Only Full Member is requested no IGMP join
will be sent.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Expose IB diagnostic hardware counters.
The counters count IB events and are applicable for IB and RoCE.
The counters can be divided into two groups, per device and per port.
Device counters are always exposed.
Port counters are exposed only if the firmware supports per port counters.
rq_num_dup and sq_num_to are only exposed if we have firmware support
for them, if we do, we expose them per device and per port.
rq_num_udsdprd and num_cqovf are device only counters.
rq - denotes responder.
sq - denotes requester.
|-----------------------|---------------------------------------|
| Name | Description |
|-----------------------|---------------------------------------|
|rq_num_lle | Number of local length errors |
|-----------------------|---------------------------------------|
|sq_num_lle | number of local length errors |
|-----------------------|---------------------------------------|
|rq_num_lqpoe | Number of local QP operation errors |
|-----------------------|---------------------------------------|
|sq_num_lqpoe | Number of local QP operation errors |
|-----------------------|---------------------------------------|
|rq_num_lpe | Number of local protection errors |
|-----------------------|---------------------------------------|
|sq_num_lpe | Number of local protection errors |
|-----------------------|---------------------------------------|
|rq_num_wrfe | Number of CQEs with error |
|-----------------------|---------------------------------------|
|sq_num_wrfe | Number of CQEs with error |
|-----------------------|---------------------------------------|
|sq_num_mwbe | Number of Memory Window bind errors |
|-----------------------|---------------------------------------|
|sq_num_bre | Number of bad response errors |
|-----------------------|---------------------------------------|
|sq_num_rire | Number of Remote Invalid request |
| | errors |
|-----------------------|---------------------------------------|
|rq_num_rire | Number of Remote Invalid request |
| | errors |
|-----------------------|---------------------------------------|
|sq_num_rae | Number of remote access errors |
|-----------------------|---------------------------------------|
|rq_num_rae | Number of remote access errors |
|-----------------------|---------------------------------------|
|sq_num_roe | Number of remote operation errors |
|-----------------------|---------------------------------------|
|sq_num_tree | Number of transport retries exceeded |
| | errors |
|-----------------------|---------------------------------------|
|sq_num_rree | Number of RNR NAK retries exceeded |
| | errors |
|-----------------------|---------------------------------------|
|rq_num_rnr | Number of RNR NAKs sent |
|-----------------------|---------------------------------------|
|sq_num_rnr | Number of RNR NAKs received |
|-----------------------|---------------------------------------|
|rq_num_oos | Number of Out of Sequence requests |
| | received |
|-----------------------|---------------------------------------|
|sq_num_oos | Number of Out of Sequence NAKs |
| | received |
|-----------------------|---------------------------------------|
|rq_num_udsdprd | Number of UD packets silently |
| | discarded on the Receive Queue due to |
| | lack of receive descriptor |
|-----------------------|---------------------------------------|
|rq_num_dup | Number of duplicate requests received |
|-----------------------|---------------------------------------|
|sq_num_to | Number of time out received |
|-----------------------|---------------------------------------|
|num_cqovf | Number of CQ overflows |
|-----------------------|---------------------------------------|
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add a function to query diagnostics counters from the firmware.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add a bit that indicates if the firmware supports per port
diagnostic counters.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
While not an issue now, eventually we will have independent users of
the extable.h file and we will stop sourcing it via module.h header.
In testing that pending work, with very sparse builds, characteristic
of an "allnoconfig" on various architectures, we can sometimes hit an
instance where the very basic standard definitions aren't present,
resulting in:
include/linux/extable.h:26:9: error: 'NULL' undeclared (first use in this function)
To be clear, this isn't a regression, since currently extable.h is
only used by module.h -- however, we will need this addition present
before we start migrating exception table users off module.h and onto
extable.h during the next release cycle.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Add ro_after_init support for modules by adding a new page-aligned section
in the module layout (after rodata) for ro_after_init data and enabling RO
protection for that section after module init runs.
Signed-off-by: Jessica Yu <jeyu@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
For historical reasons (i.e. pre-git) the exception table stuff was
buried in the middle of the module.h file. I noticed this while
doing an audit for needless includes of module.h and found core
kernel files (both arch specific and arch independent) were just
including module.h for this.
The converse is also true, in that conventional drivers, be they
for filesystems or actual hardware peripherals or similar, do not
normally care about the exception tables.
Here we fork the exception table content out of module.h into a
new file called extable.h -- and temporarily include it into the
module.h itself.
Then we will work our way across the arch independent and arch
specific files needing just exception table content, and move
them off module.h and onto extable.h
Once that is done, we can remove the extable.h from module.h
and in doing it like this, we avoid introducing build failures
into the git history.
The gain here is that module.h gets a bit smaller, across all
modular drivers that we build for allmodconfig. Also the core
files that only need exception table stuff don't have an include
of module.h that brings in lots of extra stuff and just looks
generally out of place.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs into for-linus
|
|
Only used by the vfs.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
This function is now unused.
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
Pull networking fixes from David Miller:
1) Fix several cases of missing of_node_put() calls in various
networking drivers. From Peter Chen.
2) Don't try to remove unconfigured VLANs in qed driver, from Yuval
Mintz.
3) Unbalanced locking in TIPC error handling, from Wei Yongjun.
4) Fix lockups in CPDMA driver, from Grygorii Strashko.
5) More MACSEC refcount et al fixes, from Sabrina Dubroca.
6) Fix MAC address setting in r8169 during runtime suspend, from
Chun-Hao Lin.
7) Various printf format specifier fixes, from Heinrich Schuchardt.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
qed: Fail driver load in 100g MSI mode.
ethernet: ti: davinci_emac: add missing of_node_put after calling of_parse_phandle
ethernet: stmicro: stmmac: add missing of_node_put after calling of_parse_phandle
ethernet: stmicro: stmmac: dwmac-socfpga: add missing of_node_put after calling of_parse_phandle
ethernet: renesas: sh_eth: add missing of_node_put after calling of_parse_phandle
ethernet: renesas: ravb_main: add missing of_node_put after calling of_parse_phandle
ethernet: marvell: pxa168_eth: add missing of_node_put after calling of_parse_phandle
ethernet: marvell: mvpp2: add missing of_node_put after calling of_parse_phandle
ethernet: marvell: mvneta: add missing of_node_put after calling of_parse_phandle
ethernet: hisilicon: hns: hns_dsaf_main: add missing of_node_put after calling of_parse_phandle
ethernet: hisilicon: hns: hns_dsaf_mac: add missing of_node_put after calling of_parse_phandle
ethernet: cavium: octeon: add missing of_node_put after calling of_parse_phandle
ethernet: aurora: nb8800: add missing of_node_put after calling of_parse_phandle
ethernet: arc: emac_main: add missing of_node_put after calling of_parse_phandle
ethernet: apm: xgene: add missing of_node_put after calling of_parse_phandle
ethernet: altera: add missing of_node_put
8139too: fix system hang when there is a tx timeout event.
qed: Fix error return code in qed_resc_alloc()
net: qlcnic: avoid superfluous assignement
dsa: b53: remove redundant if
...
|
|
The driver pads non-double word multiple message sizes but it doesn't
account for this padding when the packet length is calculated. Also, the
data length is miscalculated for message sizes less than 4 bytes due to
the bit representation in LRH. And there's a check for non-double word
multiple message sizes that prevents these messages from being sent.
This patch fixes length miscalculations and enables the functionality to
send non-double word multiple message sizes.
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The use of the specific opcode test is redundant since
all ack entry users correctly manipulate the mr pointer
to selectively trigger the reference clearing.
The overly specific test hinders the use of implementation
specific operations.
The change needs to get rid of the union to insure that
an atomic value is not seen as an MR pointer.
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Merge yet more updates from Andrew Morton:
- the rest of ocfs2
- various hotfixes, mainly MM
- quite a bit of misc stuff - drivers, fork, exec, signals, etc.
- printk updates
- firmware
- checkpatch
- nilfs2
- more kexec stuff than usual
- rapidio updates
- w1 things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (111 commits)
ipc: delete "nr_ipc_ns"
kcov: allow more fine-grained coverage instrumentation
init/Kconfig: add clarification for out-of-tree modules
config: add android config fragments
init/Kconfig: ban CONFIG_LOCALVERSION_AUTO with allmodconfig
relay: add global mode support for buffer-only channels
init: allow blacklisting of module_init functions
w1:omap_hdq: fix regression
w1: add helper macro module_w1_family
w1: remove need for ida and use PLATFORM_DEVID_AUTO
rapidio/switches: add driver for IDT gen3 switches
powerpc/fsl_rio: apply changes for RIO spec rev 3
rapidio: modify for rev.3 specification changes
rapidio: change inbound window size type to u64
rapidio/idt_gen2: fix locking warning
rapidio: fix error handling in mbox request/release functions
rapidio/tsi721_dma: advance queue processing from transfer submit call
rapidio/tsi721: add messaging mbox selector parameter
rapidio/tsi721: add PCIe MRRS override parameter
rapidio/tsi721_dma: add channel mask and queue size parameters
...
|
|
Pull Ceph updates from Ilya Dryomov:
"The highlights are:
- RADOS namespace support in libceph and CephFS (Zheng Yan and
myself). The stopgaps added in 4.5 to deny access to inodes in
namespaces are removed and CEPH_FEATURE_FS_FILE_LAYOUT_V2 feature
bit is now fully supported
- A large rework of the MDS cap flushing code (Zheng Yan)
- Handle some of ->d_revalidate() in RCU mode (Jeff Layton). We were
overly pessimistic before, bailing at the first sight of LOOKUP_RCU
On top of that we've got a few CephFS bug fixes, a couple of cleanups
and Arnd's workaround for a weird genksyms issue"
* tag 'ceph-for-4.8-rc1' of git://github.com/ceph/ceph-client: (34 commits)
ceph: fix symbol versioning for ceph_monc_do_statfs
ceph: Correctly return NXIO errors from ceph_llseek
ceph: Mark the file cache as unreclaimable
ceph: optimize cap flush waiting
ceph: cleanup ceph_flush_snaps()
ceph: kick cap flushes before sending other cap message
ceph: introduce an inode flag to indicates if snapflush is needed
ceph: avoid sending duplicated cap flush message
ceph: unify cap flush and snapcap flush
ceph: use list instead of rbtree to track cap flushes
ceph: update types of some local varibles
ceph: include 'follows' of pending snapflush in cap reconnect message
ceph: update cap reconnect message to version 3
ceph: mount non-default filesystem by name
libceph: fsmap.user subscription support
ceph: handle LOOKUP_RCU in ceph_d_revalidate
ceph: allow dentry_lease_is_valid to work under RCU walk
ceph: clear d_fsinfo pointer under d_lock
ceph: remove ceph_mdsc_lease_release
ceph: don't use ->d_time
...
|
|
Write-only variable.
Link: http://lkml.kernel.org/r/20160708214356.GA6785@p183.telecom.by
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
