| Age | Commit message (Collapse) | Author |
|---|
|
commit fa07ab72cbb0d843429e61bf179308aed6cbe0dd upstream.
In case __irq_set_trigger() fails the resources requested via
irq_request_resources() are not released.
Add the missing release call into the error handling path.
Fixes: c1bacbae8192 ("genirq: Provide irq_request/release_resources chip callbacks")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/655538f5-cb20-a892-ff15-fbd2dd1fa4ec@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2c4569ca26986d18243f282dd727da27e9adae4c upstream.
irq_set_chained_handler_and_data() sets up the chained interrupt and then
stores the handler data.
That's racy against an immediate interrupt which gets handled before the
store of the handler data happened. The handler will dereference a NULL
pointer and crash.
Cure it by storing handler data before installing the chained handler.
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 08d85f3ea99f1eeafc4e8507936190e86a16ee8c upstream.
Since commit f3b0946d629c ("genirq/msi: Make sure PCI MSIs are
activated early"), we can end-up activating a PCI/MSI twice (once
at allocation time, and once at startup time).
This is normally of no consequences, except that there is some
HW out there that may misbehave if activate is used more than once
(the GICv3 ITS, for example, uses the activate callback
to issue the MAPVI command, and the architecture spec says that
"If there is an existing mapping for the EventID-DeviceID
combination, behavior is UNPREDICTABLE").
While this could be worked around in each individual driver, it may
make more sense to tackle the issue at the core level. In order to
avoid getting in that situation, let's have a per-interrupt flag
to remember if we have already activated that interrupt or not.
Fixes: f3b0946d629c ("genirq/msi: Make sure PCI MSIs are activated early")
Reported-and-tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1484668848-24361-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c0af52437254fda8b0cdbaae5a9b6d9327f1fcd5 upstream.
Commit 34c3d9819fda ("genirq/affinity: Provide smarter irq spreading
infrastructure") introduced a better IRQ spreading mechanism, taking
account of the available NUMA nodes in the machine.
Problem is that the algorithm of retrieving the nodemask iterates
"linearly" based on the number of online nodes - some architectures
present non-linear node distribution among the nodemask, like PowerPC.
If this is the case, the algorithm lead to a wrong node count number
and therefore to a bad/incomplete IRQ affinity distribution.
For example, this problem were found in a machine with 128 CPUs and two
nodes, namely nodes 0 and 8 (instead of 0 and 1, if it was linearly
distributed). This led to a wrong affinity distribution which then led to
a bad mq allocation for nvme driver.
Finally, we take the opportunity to fix a comment regarding the affinity
distribution when we have _more_ nodes than vectors.
Fixes: 34c3d9819fda ("genirq/affinity: Provide smarter irq spreading infrastructure")
Reported-by: Gabriel Krisman Bertazi <gabriel@krisman.be>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Gabriel Krisman Bertazi <gabriel@krisman.be>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Cc: linux-pci@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: hch@lst.de
Link: http://lkml.kernel.org/r/1481738472-2671-1-git-send-email-gpiccoli@linux.vnet.ibm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The type flags in the irq descriptor are there for historical reasons and
only updated via irq_modify_status() or irq_set_type(). Both functions also
update the type flags in irqdata. __setup_irq() is the only left over user
of the type flags in the irq descriptor.
If __setup_irq() is called with empty irq type flags, then the type flags
are retrieved from irqdata. If an interrupt is shared, then the type flags
are compared with the type flags stored in the irq descriptor.
On x86 the ioapic does not have a irq_set_type() callback because the type
is defined in the BIOS tables and cannot be changed. The type is stored in
irqdata at setup time without updating the type data in the irq
descriptor. As a result the comparison described above fails.
There is no point in updating the irq descriptor flags because the only
relevant storage is irqdata. Use the type flags from irqdata for both
retrieval and comparison in __setup_irq() instead.
Aside of that the print out in case of non matching type flags has the old
and new type flags arguments flipped. Fix that as well.
For correctness sake the flags stored in the irq descriptor should be
removed, but this is beyond the scope of this bugfix and will be done in a
later patch.
Fixes: 4b357daed698 ("genirq: Look-up trigger type if not specified by caller")
Reported-and-tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1611072020360.3501@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The TPS65217 driver grew interrupt support which uses
irq_set_parent(). While it's not yet clear why this is used in the first
place, building the driver as a module fails with:
ERROR: ".irq_set_parent" [drivers/mfd/tps65217.ko] undefined!
The correctness of the driver change is still investigated, but for now
it's less trouble to export irq_set_parent() than dealing with the build
wreckage.
[ tglx: Rewrote changelog and made the export GPL ]
Fixes: 6556bdacf646 ("mfd: tps65217: Add support for IRQs")
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Cc: Marcin Niestroj <m.niestroj@grinn-global.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lee Jones <lee.jones@linaro.org>
Link: http://lkml.kernel.org/r/1475775403-27207-1-git-send-email-sudipm.mukherjee@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Fixes the following sparse warning:
kernel/irq/chip.c:786:1: warning:
symbol '__irq_do_set_handler' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: http://lkml.kernel.org/r/1474817799-18676-1-git-send-email-weiyj.lk@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Merge urgent fixes so pending patches for 4.9 can be applied.
|
|
There is no point in trying to configure the trigger of a chained
interrupt if no trigger information has been configured. At best
this is ignored, and at the worse this confuses the underlying
irqchip (which is likely not to handle such a thing), and
unnecessarily alarms the user.
Only apply the configuration if type is not IRQ_TYPE_NONE.
Fixes: 1e12c4a9393b ("genirq: Correctly configure the trigger on chained interrupts")
Reported-and-tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/CAMuHMdVW1eTn20=EtYcJ8hkVwohaSuH_yQXrY2MGBEvZ8fpFOg@mail.gmail.com
Link: http://lkml.kernel.org/r/1474274967-15984-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Add the new irq spreading infrastructure.
|
|
No more users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: axboe@fb.com
Cc: keith.busch@intel.com
Cc: agordeev@redhat.com
Cc: linux-block@vger.kernel.org
Link: http://lkml.kernel.org/r/1473862739-15032-5-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Switch MSI over to the new spreading code. If a pci device contains a valid
pointer to a cpumask, then this mask is used for spreading otherwise the
online cpu mask is used. This allows a driver to restrict the spread to a
subset of CPUs, e.g. cpus on a particular node.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: axboe@fb.com
Cc: keith.busch@intel.com
Cc: agordeev@redhat.com
Cc: linux-block@vger.kernel.org
Link: http://lkml.kernel.org/r/1473862739-15032-4-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The current irq spreading infrastructure is just looking at a cpumask and
tries to spread the interrupts over the mask. Thats suboptimal as it does
not take numa nodes into account.
Change the logic so the interrupts are spread across numa nodes and inside
the nodes. If there are more cpus than vectors per node, then we set the
affinity to several cpus. If HT siblings are available we take that into
account and try to set all siblings to a single vector.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: axboe@fb.com
Cc: keith.busch@intel.com
Cc: agordeev@redhat.com
Cc: linux-block@vger.kernel.org
Link: http://lkml.kernel.org/r/1473862739-15032-3-git-send-email-hch@lst.de
|
|
For irq spreading want to store affinity masks in the msi_entry. Add the
infrastructure for it.
We allocate an array of cpumasks with an array size of the number of used
vectors in the entry, so we can hand in the information per linux interrupt
later.
As we hand in the number of used vectors, we assign them right
away. Convert all the call sites.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: axboe@fb.com
Cc: keith.busch@intel.com
Cc: agordeev@redhat.com
Cc: linux-block@vger.kernel.org
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/1473862739-15032-2-git-send-email-hch@lst.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Merge the first drop of irqchip updates for 4.9 from Marc Zyngier:
- ACPI IORT core code
- IORT support for the GICv3 ITS
- A few of GIC cleanups
|
|
Information about interrupts is exposed via /proc/interrupts, but the
format of that file has changed over kernel versions and differs across
architectures. It also has varying column numbers depending on hardware.
That all makes it hard for tools to parse.
To solve this, expose the information through sysfs so each irq attribute
is in a separate file in a consistent, machine parsable way.
This feature is only available when both CONFIG_SPARSE_IRQ and
CONFIG_SYSFS are enabled.
Examples:
/sys/kernel/irq/18/actions: i801_smbus,ehci_hcd:usb1,uhci_hcd:usb7
/sys/kernel/irq/18/chip_name: IR-IO-APIC
/sys/kernel/irq/18/hwirq: 18
/sys/kernel/irq/18/name: fasteoi
/sys/kernel/irq/18/per_cpu_count: 0,0
/sys/kernel/irq/18/type: level
/sys/kernel/irq/25/actions: ahci0
/sys/kernel/irq/25/chip_name: IR-PCI-MSI
/sys/kernel/irq/25/hwirq: 512000
/sys/kernel/irq/25/name: edge
/sys/kernel/irq/25/per_cpu_count: 29036,0
/sys/kernel/irq/25/type: edge
[ tglx: Moved kobject_del() under sparse_irq_lock, massaged code comments
and changelog ]
Signed-off-by: Craig Gallek <kraig@google.com>
Cc: David Decotigny <decot@google.com>
Link: http://lkml.kernel.org/r/1473783291-122873-1-git-send-email-kraigatgoog@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Some callers of __irq_set_trigger() masks all flags except trigger mode
flags. This is unnecessary, ase __irq_set_trigger() already does this
before usage of flags.
[ tglx: Moved the flag mask and adjusted comment. Removed the hunk in
enable_percpu_irq() as it is required there ]
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Link: http://lkml.kernel.org/r/20160719095408.13778-1-kuleshovmail@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Commit 1bf4ddc46c5d ("irqdomain: Introduce irq_domain_create_{linear,
tree}") introduced the use of fwnode_handle to identify the interrupt
controller when calling __irq_domain_add but missed updating the kernel
doc parameters for the function.
Update this comment. While we are touching this code, also consolidate
the declaration and assignment of of_node.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Marc Zygnier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1464699409-23113-1-git-send-email-punit.agrawal@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Most (if not all) code here implicitly assumes that the maximum number of
IRQs per chip will be 32, and thus uses 'u32' or 'unsigned long' for many
tasks (for example "struct irq_data" declares its 'mask' field as 'u32',
and "struct irq_chip_generic" declares its 'installed' field as 'unsigned
long')
However, there is no check to verify that irqs_per_chip is <= 32. Hence,
calling irq_alloc_domain_generic_chips() with a bigger value will result in
unexpected results.
Provide a wrapper with a MAYBE_BUILD_BUG_ON(nrirqs >= 32) to catch such
cases.
[ tglx: Reduced changelog to the essential information ]
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mason <slash.tmp@free.fr>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/57B31D94.5040701@laposte.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
According to the xlate() callback definition, the 'out_type' parameter
needs to be the "linux irq type".
A mask for such bits exists, IRQ_TYPE_SENSE_MASK, which is correctly
applied in irq_domain_xlate_twocell()
So use it for irq_domain_xlate_onetwocell() as well.
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mason <slash.tmp@free.fr>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/57A05F5D.103@laposte.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Without this patch irq_domain_disassociate() cannot properly release the
interrupt. In fact, irq_map_generic_chip() checks a bit on 'gc->installed'
but said bit is never cleared, only set.
Commit 088f40b7b027 ("genirq: Generic chip: Add linear irq domain support")
added irq_map_generic_chip() function and also stated "This lacks a removal
function for now".
This commit provides an implementation of an unmap function that can be
called by irq_domain_disassociate().
[ tglx: Made the function static and removed the export as we have neither
a prototype nor a modular user. ]
Fixes: 088f40b7b027 ("genirq: Generic chip: Add linear irq domain support")
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mason <slash.tmp@free.fr>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/579F5C5A.2070507@laposte.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
irq_map_generic_chip() contains about the same code as
irq_get_domain_generic_chip() except for the return values.
Split out the irq_get_domain_generic_chip() implementation so it can be
reused.
[ tglx: Removed the extra churn in irq_get_domain_generic_chip() callers
and massaged changelog ]
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mason <slash.tmp@free.fr>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/579F5C69.8070006@laposte.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
No module users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The percpu_devid handler is not robust against spurious interrupts. If a
spurious interrupt happens and no action is installed then the handler
crashes with a NULL pointer dereference.
Add a sanity check for this and log the wreckage once in dmesg.
Reported-by: Majun <majun258@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: guohanjun@huawei.com
Cc: dingtianhong@huawei.com
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1609021436160.5647@nanos
|
|
Without locking out CPU mask operations we might end up with an inconsistent
view of the cpumask in the function.
Fixes: 5e385a6ef31f: "genirq: Add a helper to spread an affinity mask for MSI/MSI-X vectors"
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/1470924405-25728-1-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Obviously we should free action here if irq_chip_pm_get failed.
Fixes: be45beb2df69: "genirq: Add runtime power management support for IRQ chips"
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1471854112-13006-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Commit 1e2a7d78499e ("irqdomain: Don't set type when mapping an IRQ")
moved the trigger configuration call from the irqdomain mapping to
the interrupt being actually requested.
This patch failed to handle the case where we configure a chained
interrupt, which doesn't get requested through the usual path.
In order to solve this, let's call __irq_set_trigger just before
starting the cascade interrupt. Special care must be taken to
make the flow handler stick, as the .irq_set_type method could
have reset it (it doesn't know we're dealing with a chained
interrupt).
Based on an initial patch by Jon Hunter.
Fixes: 1e2a7d78499e ("irqdomain: Don't set type when mapping an IRQ")
Reported-by: John Stultz <john.stultz@linaro.org>
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Bharat Kumar Gogada reported issues with the generic MSI code, where the
end-point ended up with garbage in its MSI configuration (both for the vector
and the message).
It turns out that the two MSI paths in the kernel are doing slightly different
things:
generic MSI: disable MSI -> allocate MSI -> enable MSI -> setup EP
PCI MSI: disable MSI -> allocate MSI -> setup EP -> enable MSI
And it turns out that end-points are allowed to latch the content of the MSI
configuration registers as soon as MSIs are enabled. In Bharat's case, the
end-point ends up using whatever was there already, which is not what you
want.
In order to make things converge, we introduce a new MSI domain flag
(MSI_FLAG_ACTIVATE_EARLY) that is unconditionally set for PCI/MSI. When set,
this flag forces the programming of the end-point as soon as the MSIs are
allocated.
A consequence of this is that we have an extra activate in irq_startup, but
that should be without much consequence.
tglx:
- Several people reported a VMWare regression with PCI/MSI-X passthrough. It
turns out that the patch also cures that issue.
- We need to have a look at the MSI disable interrupt path, where we write
the msg to all zeros without disabling MSI in the PCI device. Is that
correct?
Fixes: 52f518a3a7c2 "x86/MSI: Use hierarchical irqdomains to manage MSI interrupts"
Reported-and-tested-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Reported-and-tested-by: Foster Snowhill <forst@forstwoof.ru>
Reported-by: Matthias Prager <linux@matthiasprager.de>
Reported-by: Jason Taylor <jason.taylor@simplivity.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1468426713-31431-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The new affinity hint argument of __irq_domain_alloc_irqs() is missing in
irq_reserve_ipi(). Add it.
This fixes the following compilation error:
kernel/irq/ipi.c: In function ‘irq_reserve_ipi’:
kernel/irq/ipi.c:85:9: error: too few arguments to function ‘__irq_domain_alloc_irqs’
virq = __irq_domain_alloc_irqs(domain, virq, nr_irqs, NUMA_NO_NODE,
^
Fixes: 06ee6d571f0e ("genirq: Add affinity hint to irq allocation")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: linux-pci@vger.kernel.org
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
If an irq_domain is auto-recursive and irq_domain_alloc_irqs_recursive()
for its parent has returned an error, then do return and avoid calling
irq_domain_free_irqs_recursive() uselessly, because:
- if domain->ops->alloc() had failed for an auto-recursive irq_domain,
then irq_domain_free_irqs_recursive() had already been called;
- if domain->ops->alloc() had failed for a not auto-recursive irq_domain,
then there is nothing to free at all.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1467505448-2850-1-git-send-email-alex.popov@linux.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
virq is not required to be the same for all msi descs. Use the base irq number
from the desc in the debug printk.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Pull the irq affinity managing code which is in a seperate branch for block
developers to pull.
|
|
This is lifted from the blk-mq code and adopted to use the affinity mask
concept just introduced in the irq handling code. It tries to keep the
algorithm the same as the one current used by blk-mq, but improvements
like assining vectors on a per-node basis instead of just per sibling
are possible with this simple move and refactoring.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: linux-block@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-nvme@lists.infradead.org
Cc: axboe@fb.com
Cc: agordeev@redhat.com
Link: http://lkml.kernel.org/r/1467621574-8277-7-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Allow the MSI code to provide affinity hints per MSI descriptor.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: linux-block@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-nvme@lists.infradead.org
Cc: axboe@fb.com
Cc: agordeev@redhat.com
Link: http://lkml.kernel.org/r/1467621574-8277-6-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Use the affinity hint in the irqdesc allocator. The hint is used to determine
the node for the allocation and to set the affinity of the interrupt.
If multiple interrupts are allocated (multi-MSI) then the allocator iterates
over the cpumask and for each set cpu it allocates on their node and sets the
initial affinity to that cpu.
If a single interrupt is allocated (MSI-X) then the allocator uses the first
cpu in the mask to compute the allocation node and uses the mask for the
initial affinity setting.
Interrupts set up this way are marked with the AFFINITY_MANAGED flag to
prevent userspace from messing with their affinity settings.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: linux-block@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-nvme@lists.infradead.org
Cc: axboe@fb.com
Cc: agordeev@redhat.com
Link: http://lkml.kernel.org/r/1467621574-8277-5-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Add an extra argument to the irq(domain) allocation functions, so we can hand
down affinity hints to the allocator. Thats necessary to implement proper
support for multiqueue devices.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: linux-block@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-nvme@lists.infradead.org
Cc: axboe@fb.com
Cc: agordeev@redhat.com
Link: http://lkml.kernel.org/r/1467621574-8277-4-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Interupts marked with this flag are excluded from user space interrupt
affinity changes. Contrary to the IRQ_NO_BALANCING flag, the kernel internal
affinity mechanism is not blocked.
This flag will be used for multi-queue device interrupts.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: linux-block@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-nvme@lists.infradead.org
Cc: axboe@fb.com
Cc: agordeev@redhat.com
Link: http://lkml.kernel.org/r/1467621574-8277-3-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
No user and we definitely don't want to grow one.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: linux-block@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: linux-nvme@lists.infradead.org
Cc: axboe@fb.com
Cc: agordeev@redhat.com
Link: http://lkml.kernel.org/r/1467621574-8277-2-git-send-email-hch@lst.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The function irq_create_of_mapping() is used to create an interrupt
mapping. However, depending on whether the irqdomain, to which the
interrupt belongs, is part of a hierarchy, determines whether the
mapping is created via calling irq_domain_alloc_irqs() or
irq_create_mapping().
To dispose of the interrupt mapping, drivers call irq_dispose_mapping().
However, this function does not check to see if the irqdomain is part
of a hierarchy or not and simply assumes that it was mapped via calling
irq_create_mapping() so calls irq_domain_disassociate() to unmap the
interrupt.
Fix this by checking to see if the irqdomain is part of a hierarchy and
if so call irq_domain_free_irqs() to free/unmap the interrupt.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Link: http://lkml.kernel.org/r/1466501002-16368-1-git-send-email-jonathanh@nvidia.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This adds a software irq handler for controllers that multiplex
interrupts from multiple devices, but don't know which device generated
the interrupt. For these devices, the irq handler that demuxes must
check every action for every software irq using the same h/w irq in order
to find out which device generated the interrupt. This will inevitably
trigger spurious interrupt detection if we are noting the irq.
The new irq handler does not track the handling for spurious interrupt
detection. An irq that uses this also won't get stats tracked since it
didn't generate the interrupt, nor added to randomness since they are
not random.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: Jon Derrick <jonathan.derrick@intel.com>
Link: http://lkml.kernel.org/r/1466200821-29159-1-git-send-email-keith.busch@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
First drop of irqchip updates for 4.8 from Marc Zyngier:
- Fix a few bugs in configuring the default trigger from the irqdomain layer
- Make the genirq layer PM aware
- Add PM capability to the ARM GIC driver
- Add support for 2-level translation tables to the GICv3 ITS driver
|
|
Some IRQ chips may be located in a power domain outside of the CPU
subsystem and hence will require device specific runtime power
management. In order to support such IRQ chips, add a pointer for a
device structure to the irq_chip structure, and if this pointer is
populated by the IRQ chip driver and CONFIG_PM is selected in the kernel
configuration, then the pm_runtime_get/put APIs for this chip will be
called when an IRQ is requested/freed, respectively.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Some IRQ chips, such as GPIO controllers or secondary level interrupt
controllers, may require require additional runtime power management
control to ensure they are accessible. For such IRQ chips, it makes sense
to enable the IRQ chip when interrupts are requested and disabled them
again once all interrupts have been freed.
When mapping an IRQ, the IRQ type settings are read and then programmed.
The mapping of the IRQ happens before the IRQ is requested and so the
programming of the type settings occurs before the IRQ is requested. This
is a problem for IRQ chips that require additional power management
control because they may not be accessible yet. Therefore, when mapping
the IRQ, don't program the type settings, just save them and then program
these saved settings when the IRQ is requested (so long as if they are not
overridden via the call to request the IRQ).
Add a stub function for irq_domain_free_irqs() to avoid any compilation
errors when CONFIG_IRQ_DOMAIN_HIERARCHY is not selected.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
As we now do for non-percpu interrupt, perform a lookup of the
interrupt trigger if the user doesn't supply one. The difference
here is that we can only do it at enable time (trigger configuration
can be per-cpu as well).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
For some devices the IRQ trigger type for a device is read from
firmware, such as device-tree. The IRQ trigger type is typically read
when the mapping for IRQ is created, which is before the IRQ is
requested. Hence, the IRQ trigger type is programmed when mapping the
IRQ and not when requesting the IRQ.
Although this works for most cases, in order to support IRQ chips which
require runtime power management, which may not be accessible prior
to requesting the IRQ, it is desirable to look-up the IRQ trigger type
when it is requested. Therefore, if the IRQ trigger type is not
specified when __setup_irq() is called, look-up the saved IRQ trigger
type. This will allow us to defer the programming of the trigger type
from when the IRQ is mapped to when it is actually requested.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
When mapping an IRQ, it is possible that a mapping for the IRQ already
exists. If mapping does exist then there are the following issues with
regard to the handling of the IRQ type settings ...
1. If the domain is part of a hierarchy, then:
a. We do not check that the type settings for the existing mapping
match those of the new mapping.
b. We do not check to see if the type settings have been programmed
yet (and they might not have been) and so we may never set the
type.
2. If the domain is NOT part of a hierarchy, we will overwrite the
current type settings programmed if they are different from the
previous mapping. Please note that irq_create_mapping()
calls irq_find_mapping() to check if a mapping already exists.
Although, it may be unlikely that the type settings for a shared
interrupt would not match, nonetheless we should check for this.
Therefore, to fix this check if a mapping exists (regardless of whether
the domain is part of a hierarchy or not) and if it does then:
1. Return the IRQ number if the type settings match or are not
specified.
2. Program the type settings and return the IRQ number if the type
settings have not been programmed yet.
3. Otherwise if the type setting do not match, then print a warning
and don't return the IRQ number.
Furthermore, add a warning if the type return by irq_domain_translate()
has bits outside the sense mask set and then clear these bits. If these
bits are not cleared then this will cause the comparision of the type
settings for an existing mapping to fail with that of the new mapping
even if the sense bit themselves match. The reason being is that the
existing type settings are read by calling irq_get_trigger_type() which
will clear any bits outside the sense mask. This will allow us to detect
irqchips that are not correctly clearing these bits and fix them.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
sprintf() and snprintf() implementation of kernel guarantees that
its result is terminated with null byte if size is larger than 0. So we
don't need to call memset() at all.
Signed-off-by: Weongyo Jeong <weongyo.linux@gmail.com>
Link: http://lkml.kernel.org/r/1459451703-5744-1-git-send-email-weongyo.linux@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
for_each_irq_desc() macro has already skipped NULL irq_desc, don't
bother to check it again.
Signed-off-by: Jianyu Zhan <nasa4836@gmail.com>
Cc: mingo@kernel.org
Cc: yhlu.kernel@gmail.com
Link: http://lkml.kernel.org/r/1458395959-7046-1-git-send-email-nasa4836@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Merge irqchip updates from Marc Zyngier:
- A number of embarassing buglets (GICv3, PIC32)
- A more substential errata workaround for Cavium's GICv3 ITS
(kept for post-rc1 due to its dependency on NUMA)
|
|
Commit 7cec18a3906b changed the return type of irq_destroy_ipi to int, but
missed adding a value to one return statement. Fix this to silence the
resulting compiler warning:
kernel/irq/ipi.c In function ‘irq_destroy_ipi’:
kernel/irq/ipi.c:128:3: warning: ‘return’ with no value, in function returning non-void [-Wreturn-type]
Fixes: 7cec18a3906b "genirq: Add error code reporting to irq_{reserve,destroy}_ipi"
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Link: http://lkml.kernel.org/r/1464086550-24734-1-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
