Age | Commit message (Collapse) | Author |
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
|
|
In the function, setup_irq(), we don't check that the descriptor
returned from irq_to_desc() is valid before we start using it. For
example chip_bus_lock() called from setup_irq(), assumes that the
descriptor pointer is valid and doesn't check before dereferencing it.
In many other functions including setup/free_percpu_irq() we do check
that the descriptor returned is not NULL and therefore add the same test
to setup_irq() to ensure the descriptor returned is valid.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
In order to prepare the genirq layer for the concept of partitionned
percpu interrupts, let's allow an affinity to be associated with
such an interrupt. We introduce:
- irq_set_percpu_devid_partition: flag an interrupt as a percpu-devid
interrupt, and associate it with an affinity
- irq_get_percpu_devid_partition: allow the affinity of that interrupt
to be retrieved.
This will allow a driver to discover which CPUs the per-cpu interrupt
can actually fire on.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Link: http://lkml.kernel.org/r/1460365075-7316-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When iterating over the irq domain list, we try to match a domain
either by calling a match() function or by comparing a number
of fields passed as parameters.
Both approaches are a bit restrictive:
- match() is DT specific and only takes a device node
- the fallback case only deals with the fwnode_handle
It would be useful if we had a per-domain function that would
actually perform the matching check on the whole of the
irq_fwspec structure. This would allow for a domain to triage
matching attempts that need to extend beyond the fwnode.
Let's introduce irq_find_matching_fwspec(), which takes a full
blown irq_fwspec structure, and call into a select() function
implemented by the irqdomain. irq_find_matching_fwnode() is
made a wrapper around irq_find_matching_fwspec in order to
preserve compatibility.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Link: http://lkml.kernel.org/r/1460365075-7316-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Make these functions return appropriate error codes when something goes
wrong.
Previously irq_destroy_ipi returned void making it impossible to notify
the caller if the request could not be fulfilled. Patch 1 in the series
added another condition in which this could fail in addition to the
existing ones. irq_reserve_ipi returned an unsigned int meaning it could
only return 0 on failure and give the caller no indication as to why the
request failed.
As time goes on there are likely to be further conditions added in which
these functions can fail. These APIs and the IPI IRQ domain are new in
4.6 and the number of existing call sites are low, changing the API now
has little impact on the code, while making it easier for these
functions to grow over time.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Cc: ralf@linux-mips.org
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: lisa.parratt@imgtec.com
Cc: jiang.liu@linux.intel.com
Link: http://lkml.kernel.org/r/1461568464-31701-2-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Previously irq_destroy_ipi() would destroy IPIs to all CPUs that were
configured by irq_reserve_ipi(). This change makes it possible to
destroy just a subset of the IPIs. This may be useful to remove IPIs to
CPUs that have been hot removed so that the IRQ numbers allocated within
the IPI domain can be re-used.
The original behaviour is restored by passing the complete mask that the
IPI was created with.
There are currently no users of this function that would break from the
API change.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Cc: ralf@linux-mips.org
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: lisa.parratt@imgtec.com
Cc: jiang.liu@linux.intel.com
Link: http://lkml.kernel.org/r/1461568464-31701-1-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The IPI domain re-purposes the IRQ affinity to signify the mask of CPUs
that this IPI will deliver to. This must not be modified before the IPI
is destroyed again, so set the IRQ_NO_BALANCING flag to prevent the
affinity being overwritten by setup_affinity().
Without this, if an IPI is reserved for a single target CPU, then
allocated using __setup_irq(), the affinity is overwritten with
cpu_online_mask. When ipi_destroy() is subsequently called on a
multi-cpu system, it will attempt to free cpumask_weight() IRQs
that were never allocated, and crash.
Fixes: d17bf24e6952 ("genirq: Add a new generic IPI reservation code to irq core")
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Cc: ralf@linux-mips.org
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: lisa.parratt@imgtec.com
Link: http://lkml.kernel.org/r/1461229712-13057-1-git-send-email-matt.redfearn@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Export irq_domain_free_irqs_common so it can be used by modules.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use the more common logging method with the eventual goal of removing
pr_warning altogether.
Miscellanea:
- Realign arguments
- Coalesce formats
- Add missing space between a few coalesced formats
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> [kernel/power/suspend.c]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"This time the majority of changes go into cpufreq and they are
significant.
First off, the way CPU frequency updates are triggered is different
now. Instead of having to set up and manage a deferrable timer for
each CPU in the system to evaluate and possibly change its frequency
periodically, cpufreq governors set up callbacks to be invoked by the
scheduler on a regular basis (basically on utilization updates). The
"old" governors, "ondemand" and "conservative", still do all of their
work in process context (although that is triggered by the scheduler
now), but intel_pstate does it all in the callback invoked by the
scheduler with no need for any additional asynchronous processing.
Of course, this eliminates the overhead related to the management of
all those timers, but also it allows the cpufreq governor code to be
simplified quite a bit. On top of that, the common code and data
structures used by the "ondemand" and "conservative" governors are
cleaned up and made more straightforward and some long-standing and
quite annoying problems are addressed. In particular, the handling of
governor sysfs attributes is modified and the related locking becomes
more fine grained which allows some concurrency problems to be avoided
(particularly deadlocks with the core cpufreq code).
In principle, the new mechanism for triggering frequency updates
allows utilization information to be passed from the scheduler to
cpufreq. Although the current code doesn't make use of it, in the
works is a new cpufreq governor that will make decisions based on the
scheduler's utilization data. That should allow the scheduler and
cpufreq to work more closely together in the long run.
In addition to the core and governor changes, cpufreq drivers are
updated too. Fixes and optimizations go into intel_pstate, the
cpufreq-dt driver is updated on top of some modification in the
Operating Performance Points (OPP) framework and there are fixes and
other updates in the powernv cpufreq driver.
Apart from the cpufreq updates there is some new ACPICA material,
including a fix for a problem introduced by previous ACPICA updates,
and some less significant changes in the ACPI code, like CPPC code
optimizations, ACPI processor driver cleanups and support for loading
ACPI tables from initrd.
Also updated are the generic power domains framework, the Intel RAPL
power capping driver and the turbostat utility and we have a bunch of
traditional assorted fixes and cleanups.
Specifics:
- Redesign of cpufreq governors and the intel_pstate driver to make
them use callbacks invoked by the scheduler to trigger CPU
frequency evaluation instead of using per-CPU deferrable timers for
that purpose (Rafael Wysocki).
- Reorganization and cleanup of cpufreq governor code to make it more
straightforward and fix some concurrency problems in it (Rafael
Wysocki, Viresh Kumar).
- Cleanup and improvements of locking in the cpufreq core (Viresh
Kumar).
- Assorted cleanups in the cpufreq core (Rafael Wysocki, Viresh
Kumar, Eric Biggers).
- intel_pstate driver updates including fixes, optimizations and a
modification to make it enable enable hardware-coordinated P-state
selection (HWP) by default if supported by the processor (Philippe
Longepe, Srinivas Pandruvada, Rafael Wysocki, Viresh Kumar, Felipe
Franciosi).
- Operating Performance Points (OPP) framework updates to improve its
handling of voltage regulators and device clocks and updates of the
cpufreq-dt driver on top of that (Viresh Kumar, Jon Hunter).
- Updates of the powernv cpufreq driver to fix initialization and
cleanup problems in it and correct its worker thread handling with
respect to CPU offline, new powernv_throttle tracepoint (Shilpasri
Bhat).
- ACPI cpufreq driver optimization and cleanup (Rafael Wysocki).
- ACPICA updates including one fix for a regression introduced by
previos changes in the ACPICA code (Bob Moore, Lv Zheng, David Box,
Colin Ian King).
- Support for installing ACPI tables from initrd (Lv Zheng).
- Optimizations of the ACPI CPPC code (Prashanth Prakash, Ashwin
Chaugule).
- Support for _HID(ACPI0010) devices (ACPI processor containers) and
ACPI processor driver cleanups (Sudeep Holla).
- Support for ACPI-based enumeration of the AMBA bus (Graeme Gregory,
Aleksey Makarov).
- Modification of the ACPI PCI IRQ management code to make it treat
255 in the Interrupt Line register as "not connected" on x86 (as
per the specification) and avoid attempts to use that value as a
valid interrupt vector (Chen Fan).
- ACPI APEI fixes related to resource leaks (Josh Hunt).
- Removal of modularity from a few ACPI drivers (BGRT, GHES,
intel_pmic_crc) that cannot be built as modules in practice (Paul
Gortmaker).
- PNP framework update to make it treat ACPI_RESOURCE_TYPE_SERIAL_BUS
as a valid resource type (Harb Abdulhamid).
- New device ID (future AMD I2C controller) in the ACPI driver for
AMD SoCs (APD) and in the designware I2C driver (Xiangliang Yu).
- Assorted ACPI cleanups (Colin Ian King, Kaiyen Chang, Oleg Drokin).
- cpuidle menu governor optimization to avoid a square root
computation in it (Rasmus Villemoes).
- Fix for potential use-after-free in the generic device properties
framework (Heikki Krogerus).
- Updates of the generic power domains (genpd) framework including
support for multiple power states of a domain, fixes and debugfs
output improvements (Axel Haslam, Jon Hunter, Laurent Pinchart,
Geert Uytterhoeven).
- Intel RAPL power capping driver updates to reduce IPI overhead in
it (Jacob Pan).
- System suspend/hibernation code cleanups (Eric Biggers, Saurabh
Sengar).
- Year 2038 fix for the process freezer (Abhilash Jindal).
- turbostat utility updates including new features (decoding of more
registers and CPUID fields, sub-second intervals support, GFX MHz
and RC6 printout, --out command line option), fixes (syscall jitter
detection and workaround, reductioin of the number of syscalls
made, fixes related to Xeon x200 processors, compiler warning
fixes) and cleanups (Len Brown, Hubert Chrzaniuk, Chen Yu)"
* tag 'pm+acpi-4.6-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (182 commits)
tools/power turbostat: bugfix: TDP MSRs print bits fixing
tools/power turbostat: correct output for MSR_NHM_SNB_PKG_CST_CFG_CTL dump
tools/power turbostat: call __cpuid() instead of __get_cpuid()
tools/power turbostat: indicate SMX and SGX support
tools/power turbostat: detect and work around syscall jitter
tools/power turbostat: show GFX%rc6
tools/power turbostat: show GFXMHz
tools/power turbostat: show IRQs per CPU
tools/power turbostat: make fewer systems calls
tools/power turbostat: fix compiler warnings
tools/power turbostat: add --out option for saving output in a file
tools/power turbostat: re-name "%Busy" field to "Busy%"
tools/power turbostat: Intel Xeon x200: fix turbo-ratio decoding
tools/power turbostat: Intel Xeon x200: fix erroneous bclk value
tools/power turbostat: allow sub-sec intervals
ACPI / APEI: ERST: Fixed leaked resources in erst_init
ACPI / APEI: Fix leaked resources
intel_pstate: Do not skip samples partially
intel_pstate: Remove freq calculation from intel_pstate_calc_busy()
intel_pstate: Move intel_pstate_calc_busy() into get_target_pstate_use_performance()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The 4.6 pile of irq updates contains:
- Support for IPI irqdomains to support proper integration of IPIs to
and from coprocessors. The first user of this new facility is
MIPS. The relevant MIPS patches come with the core to avoid merge
ordering issues and have been acked by Ralf.
- A new command line option to set the default interrupt affinity
mask at boot time.
- Support for some more new ARM and MIPS interrupt controllers:
tango, alpine-msix and bcm6345-l1
- Two small cleanups for x86/apic which we merged into irq/core to
avoid yet another branch in x86 with two tiny commits.
- The usual set of updates, cleanups in drivers/irqchip. Mostly in
the area of ARM-GIC, arada-37-xp and atmel chips. Nothing
outstanding here"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (56 commits)
irqchip/irq-alpine-msi: Release the correct domain on error
irqchip/mxs: Fix error check of of_io_request_and_map()
irqchip/sunxi-nmi: Fix error check of of_io_request_and_map()
genirq: Export IRQ functions for module use
irqchip/gic/realview: Support more RealView DCC variants
Documentation/bindings: Document the Alpine MSIX driver
irqchip: Add the Alpine MSIX interrupt controller
irqchip/gic-v3: Always return IRQ_SET_MASK_OK_DONE in gic_set_affinity
irqchip/gic-v3-its: Mark its_init() and its children as __init
irqchip/gic-v3: Remove gic_root_node variable from the ITS code
irqchip/gic-v3: ACPI: Add redistributor support via GICC structures
irqchip/gic-v3: Add ACPI support for GICv3/4 initialization
irqchip/gic-v3: Refactor gic_of_init() for GICv3 driver
x86/apic: Deinline _flat_send_IPI_mask, save ~150 bytes
x86/apic: Deinline __default_send_IPI_*, save ~200 bytes
dt-bindings: interrupt-controller: Add SoC-specific compatible string to Marvell ODMI
irqchip/mips-gic: Add new DT property to reserve IPIs
MIPS: Delete smp-gic.c
MIPS: Make smp CMP, CPS and MT use the new generic IPI functions
MIPS: Add generic SMP IPI support
...
|
|
Conflicts:
kernel/rcu/tree.c
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Export irq_chip_*_parent(), irq_domain_create_hierarchy(),
irq_domain_set_hwirq_and_chip(), irq_domain_reset_irq_data(),
irq_domain_alloc/free_irqs_parent()
So gpio drivers can be built as modules. First user: gpio-xgene-sb
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Phong Vo <pvo@apm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: patches@apm.com
Cc: Loc Ho <lho@apm.com>
Cc: Keyur Chudgar <kchudgar@apm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Link: https://lists.01.org/pipermail/kbuild-all/2016-February/017914.html
Link: http://lkml.kernel.org/r/1457017012-10628-1-git-send-email-qnguyen@apm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Per the x86-specific footnote to PCI spec r3.0, sec 6.2.4, the value 255 in
the Interrupt Line register means "unknown" or "no connection."
Previously, when we couldn't derive an IRQ from the _PRT, we fell back to
using the value from Interrupt Line as an IRQ. It's questionable whether
we should do that at all, but the spec clearly suggests we shouldn't do it
for the value 255 on x86.
Calling request_irq() with IRQ 255 may succeed, but the driver won't
receive any interrupts. Or, if IRQ 255 is shared with another device, it
may succeed, and the driver's ISR will be called at random times when the
*other* device interrupts. Or it may fail if another device is using IRQ
255 with incompatible flags. What we *want* is for request_irq() to fail
predictably so the driver can fall back to polling.
On x86, assume 255 in the Interrupt Line means the INTx line is not
connected. In that case, set dev->irq to IRQ_NOTCONNECTED so request_irq()
will fail gracefully with -ENOTCONN.
We found this problem on a system where Secure Boot firmware assigned
Interrupt Line 255 to an i801_smbus device and another device was already
using MSI-X IRQ 255. This was in v3.10, where i801_probe() fails if
request_irq() fails:
i801_smbus 0000:00:1f.3: enabling device (0140 -> 0143)
i801_smbus 0000:00:1f.3: can't derive routing for PCI INT C
i801_smbus 0000:00:1f.3: PCI INT C: no GSI
genirq: Flags mismatch irq 255. 00000080 (i801_smbus) vs. 00000000 (megasa)
CPU: 0 PID: 2487 Comm: kworker/0:1 Not tainted 3.10.0-229.el7.x86_64 #1
Hardware name: FUJITSU PRIMEQUEST 2800E2/D3736, BIOS PRIMEQUEST 2000 Serie5
Call Trace:
dump_stack+0x19/0x1b
__setup_irq+0x54a/0x570
request_threaded_irq+0xcc/0x170
i801_probe+0x32f/0x508 [i2c_i801]
local_pci_probe+0x45/0xa0
i801_smbus 0000:00:1f.3: Failed to allocate irq 255: -16
i801_smbus: probe of 0000:00:1f.3 failed with error -16
After aeb8a3d16ae0 ("i2c: i801: Check if interrupts are disabled"),
i801_probe() will fall back to polling if request_irq() fails. But we
still need this patch because request_irq() may succeed or fail depending
on other devices in the system. If request_irq() fails, i801_smbus will
work by falling back to polling, but if it succeeds, i801_smbus won't work
because it expects interrupts that it may not receive.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add APIs to send IPIs from driver and arch code.
We have different functions because we allow architecture code to cache the
irq descriptor to avoid lookups. Driver code has to use the irq number and is
subject to more restrictive checks.
[ tglx: Polish the implementation ]
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-12-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
When dealing with coprocessors we need to find out the actual hwirqs values to
pass on to the firmware so that it knows what it needs to use to receive IPIs
from and send IPIs to Linux cpus.
[ tglx: Fixed the single hwirq IPI case. The hardware irq number does not
change due to the cpu number ]
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-10-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Add a generic mechanism to dynamically allocate an IPI. Depending on the
underlying implementation this creates either a single Linux irq or a
consective range of Linux irqs. The Linux irq is used later to send IPIs to
other CPUs.
[ tglx: Massaged the code and removed the 'consecutive mask' restriction for
the single IRQ case ]
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-9-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We will need to use this function to implement irq_reserve_ipi() later. So
make it non static and move the prototype to irqdomain.h to allow using it
outside irqdomain.c
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-8-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Select this to enable the generic IPI domain support
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: <jason@lakedaemon.net>
Cc: <marc.zyngier@arm.com>
Cc: <jiang.liu@linux.intel.com>
Cc: <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Cc: <lisa.parratt@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Link: http://lkml.kernel.org/r/1449580830-23652-4-git-send-email-qais.yousef@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
irq_common_data::state_use_accessors is not designed for public use.
Therefore make it private so that people who write code accessing it
directly will get blamed by sparse. Also #undef the macro
__irqd_to_state after used in header files, so that the macro can't be
misused.
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
|
|
The irq code browses the list of actions differently to inspect the element
one by one. Even if it is not a problem, for the sake of consistent code,
provide a macro similar to for_each_irq_desc in order to have the same loop to
go through the actions list and use it in the code.
[ tglx: Renamed the macro ]
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/1452765253-31148-1-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
If we isolate CPUs, then we don't want random device interrupts on them. Even
w/o the user space irq balancer enabled we can end up with irqs on non boot
cpus and chasing newly requested interrupts is a tedious task.
Allow to restrict the default irq affinity mask.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1602031948190.25254@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull IRQ fixes from Ingo Molnar:
"Mostly irqchip driver fixes, but also an irq core crash fix and a
build fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/mxs: Add missing set_handle_irq()
irqchip/atmel-aic: Fix wrong bit operation for IRQ priority
irqchip/gic-v3-its: Recompute the number of pages on page size change
base: Export platform_msi_domain_[alloc,free]_irqs
of: MSI: Simplify irqdomain lookup
irqdomain: Allow domain lookup with DOMAIN_BUS_WIRED token
irqchip: Fix dependencies for archs w/o HAS_IOMEM
irqchip/s3c24xx: Mark init_eint as __maybe_unused
genirq: Validate action before dereferencing it in handle_irq_event_percpu()
|
|
Let's take the (outlandish) example of an interrupt controller
capable of handling both wired interrupts and PCI MSIs.
With the current code, the PCI MSI domain is going to be tagged
with DOMAIN_BUS_PCI_MSI, and the wired domain with DOMAIN_BUS_ANY.
Things get hairy when we start looking up the domain for a wired
interrupt (typically when creating it based on some firmware
information - DT or ACPI).
In irq_create_fwspec_mapping(), we perform the lookup using
DOMAIN_BUS_ANY, which is actually used as a wildcard. This gives
us one chance out of two to end up with the wrong domain, and
we try to configure a wired interrupt with the MSI domain.
Everything grinds to a halt pretty quickly.
What we really need to do is to start looking for a domain that
would uniquely identify a wired interrupt domain, and only use
DOMAIN_BUS_ANY as a fallback.
In order to solve this, let's introduce a new DOMAIN_BUS_WIRED
token, which is going to be used exactly as described above.
Of course, this depends on the irqchip to setup the domain
bus_token, and nobody had to implement this so far.
Only so far.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Link: http://lkml.kernel.org/r/1453816347-32720-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes for the v4.5 merge window:
Enumeration:
- Simplify config space size computation (Bjorn Helgaas)
- Avoid iterating through ROM outside the resource window (Edward O'Callaghan)
- Support PCIe devices with short cfg_size (Jason S. McMullan)
- Add Netronome vendor and device IDs (Jason S. McMullan)
- Limit config space size for Netronome NFP6000 family (Jason S. McMullan)
- Add Netronome NFP4000 PF device ID (Simon Horman)
- Limit config space size for Netronome NFP4000 (Simon Horman)
- Print warnings for all invalid expansion ROM headers (Vladis Dronov)
Resource management:
- Fix minimum allocation address overwrite (Christoph Biedl)
PCI device hotplug:
- acpiphp_ibm: Fix null dereferences on null ibm_slot (Colin Ian King)
- pciehp: Always protect pciehp_disable_slot() with hotplug mutex (Guenter Roeck)
- shpchp: Constify hpc_ops structure (Julia Lawall)
- ibmphp: Remove unneeded NULL test (Julia Lawall)
Power management:
- Make ASPM sysfs link_state_store() consistent with link_state_show() (Andy Lutomirski)
Virtualization
- Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183 (Tim Sander)
MSI:
- Remove empty pci_msi_init_pci_dev() (Bjorn Helgaas)
- Mark PCIe/PCI (MSI) IRQ cascade handlers as IRQF_NO_THREAD (Grygorii Strashko)
- Initialize MSI capability for all architectures (Guilherme G. Piccoli)
- Relax msi_domain_alloc() to support parentless MSI irqdomains (Liu Jiang)
ARM Versatile host bridge driver:
- Remove unused pci_sys_data structures (Lorenzo Pieralisi)
Broadcom iProc host bridge driver:
- Hide CONFIG_PCIE_IPROC (Arnd Bergmann)
- Do not use 0x in front of %pap (Dmitry V. Krivenok)
- Update iProc PCIe device tree binding (Ray Jui)
- Add PAXC interface support (Ray Jui)
- Add iProc PCIe MSI device tree binding (Ray Jui)
- Add iProc PCIe MSI support (Ray Jui)
Freescale i.MX6 host bridge driver:
- Use gpio_set_value_cansleep() (Fabio Estevam)
- Add support for active-low reset GPIO (Petr Štetiar)
HiSilicon host bridge driver:
- Add support for HiSilicon Hip06 PCIe host controllers (Gabriele Paoloni)
Intel VMD host bridge driver:
- Export irq_domain_set_info() for module use (Keith Busch)
- x86/PCI: Allow DMA ops specific to a PCI domain (Keith Busch)
- Use 32 bit PCI domain numbers (Keith Busch)
- Add driver for Intel Volume Management Device (VMD) (Keith Busch)
Qualcomm host bridge driver:
- Document PCIe devicetree bindings (Stanimir Varbanov)
- Add Qualcomm PCIe controller driver (Stanimir Varbanov)
- dts: apq8064: add PCIe devicetree node (Stanimir Varbanov)
- dts: ifc6410: enable PCIe DT node for this board (Stanimir Varbanov)
Renesas R-Car host bridge driver:
- Add support for R-Car H3 to pcie-rcar (Harunobu Kurokawa)
- Allow DT to override default window settings (Phil Edworthy)
- Convert to DT resource parsing API (Phil Edworthy)
- Revert "PCI: rcar: Build pcie-rcar.c only on ARM" (Phil Edworthy)
- Remove unused pci_sys_data struct from pcie-rcar (Phil Edworthy)
- Add runtime PM support to pcie-rcar (Phil Edworthy)
- Add Gen2 PHY setup to pcie-rcar (Phil Edworthy)
- Add gen2 fallback compatibility string for pci-rcar-gen2 (Simon Horman)
- Add gen2 fallback compatibility string for pcie-rcar (Simon Horman)
Synopsys DesignWare host bridge driver:
- Simplify control flow (Bjorn Helgaas)
- Make config accessor override checking symmetric (Bjorn Helgaas)
- Ensure ATU is enabled before IO/conf space accesses (Stanimir Varbanov)
Miscellaneous:
- Add of_pci_get_host_bridge_resources() stub (Arnd Bergmann)
- Check for PCI_HEADER_TYPE_BRIDGE equality, not bitmask (Bjorn Helgaas)
- Fix all whitespace issues (Bogicevic Sasa)
- x86/PCI: Simplify pci_bios_{read,write} (Geliang Tang)
- Use to_pci_dev() instead of open-coding it (Geliang Tang)
- Use kobj_to_dev() instead of open-coding it (Geliang Tang)
- Use list_for_each_entry() to simplify code (Geliang Tang)
- Fix typos in <linux/msi.h> (Thomas Petazzoni)
- x86/PCI: Clarify AMD Fam10h config access restrictions comment (Tomasz Nowicki)"
* tag 'pci-v4.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (58 commits)
PCI: Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183
PCI: Limit config space size for Netronome NFP4000
PCI: Add Netronome NFP4000 PF device ID
x86/PCI: Add driver for Intel Volume Management Device (VMD)
PCI/AER: Use 32 bit PCI domain numbers
x86/PCI: Allow DMA ops specific to a PCI domain
irqdomain: Export irq_domain_set_info() for module use
PCI: host: Add of_pci_get_host_bridge_resources() stub
genirq/MSI: Relax msi_domain_alloc() to support parentless MSI irqdomains
PCI: rcar: Add Gen2 PHY setup to pcie-rcar
PCI: rcar: Add runtime PM support to pcie-rcar
PCI: designware: Make config accessor override checking symmetric
PCI: ibmphp: Remove unneeded NULL test
ARM: dts: ifc6410: enable PCIe DT node for this board
ARM: dts: apq8064: add PCIe devicetree node
PCI: hotplug: Use list_for_each_entry() to simplify code
PCI: rcar: Remove unused pci_sys_data struct from pcie-rcar
PCI: hisi: Add support for HiSilicon Hip06 PCIe host controllers
PCI: Avoid iterating through memory outside the resource window
PCI: acpiphp_ibm: Fix null dereferences on null ibm_slot
...
|
|
Export irq_domain_set_info() for module use. It will be used by the Volume
Management Device driver.
[bhelgaas: changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Previously msi_domain_alloc() assumed MSI irqdomains always had parent
irqdomains, but that's not true for the new Intel VMD devices. Relax
msi_domain_alloc() to support parentless MSI irqdomains.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
|
|
commit 71f64340fc0e changed the handling of irq_desc->action from
CPU 0 CPU 1
free_irq() lock(desc)
lock(desc) handle_edge_irq()
if (desc->action) {
handle_irq_event()
action = desc->action
unlock(desc)
desc->action = NULL handle_irq_event_percpu(desc, action)
action->xxx
to
CPU 0 CPU 1
free_irq() lock(desc)
lock(desc) handle_edge_irq()
if (desc->action) {
handle_irq_event()
unlock(desc)
desc->action = NULL handle_irq_event_percpu(desc, action)
action = desc->action
action->xxx
So if free_irq manages to set the action to NULL between the unlock and before
the readout, we happily dereference a null pointer.
We could simply revert 71f64340fc0e, but we want to preserve the better code
generation. A simple solution is to change the action loop from a do {} while
to a while {} loop.
This is safe because we either see a valid desc->action or NULL. If the action
is about to be removed it is still valid as free_irq() is blocked on
synchronize_irq().
CPU 0 CPU 1
free_irq() lock(desc)
lock(desc) handle_edge_irq()
handle_irq_event(desc)
set(INPROGRESS)
unlock(desc)
handle_irq_event_percpu(desc)
action = desc->action
desc->action = NULL while (action) {
action->xxx
...
action = action->next;
sychronize_irq()
while(INPROGRESS); lock(desc)
clr(INPROGRESS)
free(action)
That's basically the same mechanism as we have for shared
interrupts. action->next can become NULL while handle_irq_event_percpu()
runs. Either it sees the action or NULL. It does not matter, because action
itself cannot go away before the interrupt in progress flag has been cleared.
Fixes: commit 71f64340fc0e "genirq: Remove the second parameter from handle_irq_event_percpu()"
Reported-by: zyjzyj2000@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Huang Shijie <shijie.huang@arm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1601131224190.3575@nanos
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The irq department provides:
- Support for MSI to wire bridges and a first user of it
- More ACPI support for ARM/GIC
- A new TS-4800 interrupt controller driver
- RCU based free of interrupt descriptors to support the upcoming
Intel VMD technology without introducing a locking nightmare
- The usual pile of fixes and updates to drivers and core code"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
irqchip/omap-intc: Add support for spurious irq handling
irqchip/zevio: Use irq_data_get_chip_type() helper
irqchip/omap-intc: Remove duplicate setup for IRQ chip type handler
irqchip/ts4800: Add TS-4800 interrupt controller
irqchip/ts4800: Add documentation for TS-4800 interrupt controller
irq/platform-MSI: Increase the maximum MSIs the MSI framework can support
irqchip/gicv2m: Miscellaneous fixes for v2m resources and SPI ranges
irqchip/bcm2836: Make code more readable
irqchip/bcm2836: Tolerate IRQs while no flag is set in ISR
irqchip/bcm2836: Add SMP support for the 2836
irqchip/bcm2836: Fix initialization of the LOCAL_IRQ_CNT timers
irqchip/gic-v2m: acpi: Introducing GICv2m ACPI support
irqchip/gic-v2m: Refactor to prepare for ACPI support
irqdomain: Introduce is_fwnode_irqchip helper
acpi: pci: Setup MSI domain for ACPI based pci devices
genirq/msi: Export functions to allow MSI domains in modules
irqchip/mbigen: Implement the mbigen irq chip operation functions
irqchip/mbigen: Create irq domain for each mbigen device
irqchip/mgigen: Add platform device driver for mbigen device
dt-bindings: Documents the mbigen bindings
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull another round of GIC changes from Marc:
ACPI support for GIV-v2m
|
|
Since there will be several places checking if fwnode.type
is equal FWNODE_IRQCHIP, this patch adds a convenient function
for this purpose.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The Linux kernel already has the concept of IRQ domain, wherein a
component can expose a set of IRQs which are managed by a particular
interrupt controller chip or other subsystem. The PCI driver exposes
the notion of an IRQ domain for Message-Signaled Interrupts (MSI) from
PCI Express devices. This patch exposes the functions which are
necessary for creating a MSI IRQ domain within a module.
[ tglx: Split it into x86 and core irq parts ]
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Cc: gregkh@linuxfoundation.org
Cc: kys@microsoft.com
Cc: devel@linuxdriverproject.org
Cc: olaf@aepfle.de
Cc: apw@canonical.com
Cc: vkuznets@redhat.com
Cc: haiyangz@microsoft.com
Cc: marc.zyngier@arm.com
Cc: bhelgaas@google.com
Link: http://lkml.kernel.org/r/1449769983-12948-4-git-send-email-jakeo@microsoft.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull the MSI wire bridge implementation from Marc Zyngier along with
the first user of it. This is infrastructure to support a wired
interrupt to MSI interrupt brigde. The first user is mbigen found in
Hisilicon ARM SoCs.
|
|
To be able to allocate interrupts from the MSI layer down,
add a new msi_domain_populate_irqs entry point.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The .prepare callbacks are so far only called from msi_domain_alloc_irqs.
In order to reuse that code, split that code and create a
msi_domain_prepare_irqs function that the existing code can call into.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
We are soon going to need the MSI layer to call into the domain
allocators. Instead of open coding this, make the standard
irq_domain_alloc_irqs_recursive function available to the MSI
layer.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The new VMD device driver needs to iterate over a list of
"demultiplexing" interrupts. Protecting that list with a lock is not
possible because the list is also required in code pathes which hold
irq descriptor lock. Therefor the demultiplexing interrupt handler
would create a lock inversion scenario if it calls a demux handler
with the list protection lock held.
A solution for this is to free the irq descriptor via RCU, so the
list can be walked with rcu read lock held.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Keith Busch <keith.busch@intel.com>
|
|
If a interrupt chip utilizes chip->buslock then free_irq() can
deadlock in the following way:
CPU0 CPU1
interrupt(X) (Shared or spurious)
free_irq(X) interrupt_thread(X)
chip_bus_lock(X)
irq_finalize_oneshot(X)
chip_bus_lock(X)
synchronize_irq(X)
synchronize_irq() waits for the interrupt thread to complete,
i.e. forever.
Solution is simple: Drop chip_bus_lock() before calling
synchronize_irq() as we do with the irq_desc lock. There is nothing to
be protected after the point where irq_desc lock has been released.
This adds chip_bus_lock/unlock() to the remove_irq() code path, but
that's actually correct in the case where remove_irq() is called on
such an interrupt. The current users of remove_irq() are not affected
as none of those interrupts is on a chip which requires buslock.
Reported-by: Fredrik Markström <fredrik.markstrom@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
|
|
Certain interrupt controller drivers have a register set that does not
make it easy to save/restore the mask of enabled/disabled interrupts
at suspend/resume time. At resume time, such drivers rely on the core
kernel irq subsystem to tell whether such or such interrupt is enabled
or not, in order to restore the proper state in the interrupt
controller register.
While the irqd_irq_disabled() provides the relevant information for
global interrupts, there is no similar function to query the
enabled/disabled state of a per-CPU interrupt.
Therefore, this commit complements the percpu_irq API with an
irq_percpu_is_enabled() function.
[ tglx: Simplified the implementation and added kerneldoc ]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Tawfik Bayouk <tawfik@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Lior Amsalem <alior@marvell.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1445347435-2333-2-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
In case of a wakeup interrupt, irq_pm_check_wakeup disables the interrupt
and marks it pending and suspended, disables it and notifies the pm core
about the wake event. The interrupt gets handled later once the system
is resumed.
However the irq stats is updated twice: once when it's disabled waiting
for the system to resume and later when it's handled, resulting in wrong
counting of the wakeup interrupt when waking up the system.
This patch updates the interrupt count so that it's updated only when
the interrupt gets handled. It's already handled correctly in
handle_edge_irq and handle_edge_eoi_irq.
Reported-by: Manoil Claudiu <claudiu.manoil@freescale.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/1446661957-1019-1-git-send-email-sudeep.holla@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq and timer fixes from Thomas Gleixner:
- An irq regression fix to restore the wakeup behaviour of chained
interrupts.
- A timer fix for a long standing race versus timers scheduled on a
target cpu which got exposed by recent changes in the workqueue
implementation.
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/PM: Restore system wake up from chained interrupts
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Use proper base migration in add_timer_on()
|
|
Commit e509bd7da149 ("genirq: Allow migration of chained interrupts
by installing default action") breaks PCS wake up IRQ behaviour on
TI OMAP based platforms (dra7-evm).
TI OMAP IRQ wake up configuration:
GIC-irqchip->PCM_IRQ
|- omap_prcm_register_chain_handler
|- PRCM-irqchip -> PRCM_IO_IRQ
|- pcs_irq_chain_handler
|- pinctrl-irqchip -> PCS_uart1_wakeup_irq
This happens because IRQ PM code (irq/pm.c) is expected to ignore
chained interrupts by default:
static bool suspend_device_irq(struct irq_desc *desc)
{
if (!desc->action || desc->no_suspend_depth)
return false;
- it's expected !desc->action = true for chained interrupts;
but, after above change, all chained interrupt descriptors will
have default action handler installed - chained_action.
As result, chained interrupts will be silently disabled during system
suspend.
Hence, fix it by introducing helper function irq_desc_is_chained() and
use it in suspend_device_irq() for chained interrupts identification
and skip them, once detected.
Fixes: e509bd7da149 ("genirq: Allow migration of chained interrupts..")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: <nsekhar@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tony Lindgren <tony@atomide.com>
Link: http://lkml.kernel.org/r/1447149492-20699-1-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"Quite a new features are included this time.
First off, the Collaborative Processor Performance Control interface
(version 2) defined by ACPI will now be supported on ARM64 along with
a cpufreq frontend for CPU performance scaling.
Second, ACPI gets a new infrastructure for the early probing of IRQ
chips and clock sources (along the lines of the existing similar
mechanism for DT).
Next, the ACPI core and the generic device properties API will now
support a recently introduced hierarchical properties extension of the
_DSD (Device Specific Data) ACPI device configuration object. If the
ACPI platform firmware uses that extension to organize device
properties in a hierarchical way, the kernel will automatically handle
it and make those properties available to device drivers via the
generic device properties API.
It also will be possible to build the ACPICA's AML interpreter
debugger into the kernel now and use that to diagnose AML-related
problems more efficiently. In the future, this should make it
possible to single-step AML execution and do similar things.
Interesting stuff, although somewhat experimental at this point.
Finally, the PM core gets a new mechanism that can be used by device
drivers to distinguish between suspend-to-RAM (based on platform
firmware support) and suspend-to-idle (or other variants of system
suspend the platform firmware is not involved in) and possibly
optimize their device suspend/resume handling accordingly.
In addition to that, some existing features are re-organized quite
substantially.
First, the ACPI-based handling of PCI host bridges on x86 and ia64 is
unified and the common code goes into the ACPI core (so as to reduce
code duplication and eliminate non-essential differences between the
two architectures in that area).
Second, the Operating Performance Points (OPP) framework is
reorganized to make the code easier to find and follow.
Next, the cpufreq core's sysfs interface is reorganized to get rid of
the "primary CPU" concept for configurations in which the same
performance scaling settings are shared between multiple CPUs.
Finally, some interfaces that aren't necessary any more are dropped
from the generic power domains framework.
On top of the above we have some minor extensions, cleanups and bug
fixes in multiple places, as usual.
Specifics:
- ACPICA update to upstream revision 20150930 (Bob Moore, Lv Zheng).
The most significant change is to allow the AML debugger to be
built into the kernel. On top of that there is an update related
to the NFIT table (the ACPI persistent memory interface) and a few
fixes and cleanups.
- ACPI CPPC2 (Collaborative Processor Performance Control v2) support
along with a cpufreq frontend (Ashwin Chaugule).
This can only be enabled on ARM64 at this point.
- New ACPI infrastructure for the early probing of IRQ chips and
clock sources (Marc Zyngier).
- Support for a new hierarchical properties extension of the ACPI
_DSD (Device Specific Data) device configuration object allowing
the kernel to handle hierarchical properties (provided by the
platform firmware this way) automatically and make them available
to device drivers via the generic device properties interface
(Rafael Wysocki).
- Generic device properties API extension to obtain an index of
certain string value in an array of strings, along the lines of
of_property_match_string(), but working for all of the supported
firmware node types, and support for the "dma-names" device
property based on it (Mika Westerberg).
- ACPI core fix to parse the MADT (Multiple APIC Description Table)
entries in the order expected by platform firmware (and mandated by
the specification) to avoid confusion on systems with more than 255
logical CPUs (Lukasz Anaczkowski).
- Consolidation of the ACPI-based handling of PCI host bridges on x86
and ia64 (Jiang Liu).
- ACPI core fixes to ensure that the correct IRQ number is used to
represent the SCI (System Control Interrupt) in the cases when it
has been re-mapped (Chen Yu).
- New ACPI backlight quirk for Lenovo IdeaPad S405 (Hans de Goede).
- ACPI EC driver fixes (Lv Zheng).
- Assorted ACPI fixes and cleanups (Dan Carpenter, Insu Yun, Jiri
Kosina, Rami Rosen, Rasmus Villemoes).
- New mechanism in the PM core allowing drivers to check if the
platform firmware is going to be involved in the upcoming system
suspend or if it has been involved in the suspend the system is
resuming from at the moment (Rafael Wysocki).
This should allow drivers to optimize their suspend/resume handling
in some cases and the changes include a couple of users of it (the
i8042 input driver, PCI PM).
- PCI PM fix to prevent runtime-suspended devices with PME enabled
from being resumed during system suspend even if they aren't
configured to wake up the system from sleep (Rafael Wysocki).
- New mechanism to report the number of a wakeup IRQ that woke up the
system from sleep last time (Alexandra Yates).
- Removal of unused interfaces from the generic power domains
framework and fixes related to latency measurements in that code
(Ulf Hansson, Daniel Lezcano).
- cpufreq core sysfs interface rework to make it handle CPUs that
share performance scaling settings (represented by a common cpufreq
policy object) more symmetrically (Viresh Kumar).
This should help to simplify the CPU offline/online handling among
other things.
- cpufreq core fixes and cleanups (Viresh Kumar).
- intel_pstate fixes related to the Turbo Activation Ratio (TAR)
mechanism on client platforms which causes the turbo P-states range
to vary depending on platform firmware settings (Srinivas
Pandruvada).
- intel_pstate sysfs interface fix (Prarit Bhargava).
- Assorted cpufreq driver (imx, tegra20, powernv, integrator) fixes
and cleanups (Bai Ping, Bartlomiej Zolnierkiewicz, Shilpasri G
Bhat, Luis de Bethencourt).
- cpuidle mvebu driver cleanups (Russell King).
- OPP (Operating Performance Points) framework code reorganization to
make it more maintainable (Viresh Kumar).
- Intel Broxton support for the RAPL (Running Average Power Limits)
power capping driver (Amy Wiles).
- Assorted power management code fixes and cleanups (Dan Carpenter,
Geert Uytterhoeven, Geliang Tang, Luis de Bethencourt, Rasmus
Villemoes)"
* tag 'pm+acpi-4.4-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (108 commits)
cpufreq: postfix policy directory with the first CPU in related_cpus
cpufreq: create cpu/cpufreq/policyX directories
cpufreq: remove cpufreq_sysfs_{create|remove}_file()
cpufreq: create cpu/cpufreq at boot time
cpufreq: Use cpumask_copy instead of cpumask_or to copy a mask
cpufreq: ondemand: Drop unnecessary locks from update_sampling_rate()
PM / Domains: Merge measurements for PM QoS device latencies
PM / Domains: Don't measure ->start|stop() latency in system PM callbacks
PM / clk: Fix broken build due to non-matching code and header #ifdefs
ACPI / Documentation: add copy_dsdt to ACPI format options
ACPI / sysfs: correctly check failing memory allocation
ACPI / video: Add a quirk to force native backlight on Lenovo IdeaPad S405
ACPI / CPPC: Fix potential memory leak
ACPI / CPPC: signedness bug in register_pcc_channel()
ACPI / PAD: power_saving_thread() is not freezable
ACPI / PM: Fix incorrect wakeup IRQ setting during suspend-to-idle
ACPI: Using correct irq when waiting for events
ACPI: Use correct IRQ when uninstalling ACPI interrupt handler
cpuidle: mvebu: disable the bind/unbind attributes and use builtin_platform_driver
cpuidle: mvebu: clean up multiple platform drivers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- "genirq: Introduce generic irq migration for cpu hotunplugged" patch
merged from tip/irq/for-arm to allow the arm64-specific part to be
upstreamed via the arm64 tree
- CPU feature detection reworked to cope with heterogeneous systems
where CPUs may not have exactly the same features. The features
reported by the kernel via internal data structures or ELF_HWCAP are
delayed until all the CPUs are up (and before user space starts)
- Support for 16KB pages, with the additional bonus of a 36-bit VA
space, though the latter only depending on EXPERT
- Implement native {relaxed, acquire, release} atomics for arm64
- New ASID allocation algorithm which avoids IPI on roll-over, together
with TLB invalidation optimisations (using local vs global where
feasible)
- KASan support for arm64
- EFI_STUB clean-up and isolation for the kernel proper (required by
KASan)
- copy_{to,from,in}_user optimisations (sharing the memcpy template)
- perf: moving arm64 to the arm32/64 shared PMU framework
- L1_CACHE_BYTES increased to 128 to accommodate Cavium hardware
- Support for the contiguous PTE hint on kernel mapping (16 consecutive
entries may be able to use a single TLB entry)
- Generic CONFIG_HZ now used on arm64
- defconfig updates
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (91 commits)
arm64/efi: fix libstub build under CONFIG_MODVERSIONS
ARM64: Enable multi-core scheduler support by default
arm64/efi: move arm64 specific stub C code to libstub
arm64: page-align sections for DEBUG_RODATA
arm64: Fix build with CONFIG_ZONE_DMA=n
arm64: Fix compat register mappings
arm64: Increase the max granular size
arm64: remove bogus TASK_SIZE_64 check
arm64: make Timer Interrupt Frequency selectable
arm64/mm: use PAGE_ALIGNED instead of IS_ALIGNED
arm64: cachetype: fix definitions of ICACHEF_* flags
arm64: cpufeature: declare enable_cpu_capabilities as static
genirq: Make the cpuhotplug migration code less noisy
arm64: Constify hwcap name string arrays
arm64/kvm: Make use of the system wide safe values
arm64/debug: Make use of the system wide safe value
arm64: Move FP/ASIMD hwcap handling to common code
arm64/HWCAP: Use system wide safe values
arm64/capabilities: Make use of system wide safe value
arm64: Delay cpu feature capability checks
...
|
|
Pull networking updates from David Miller:
Changes of note:
1) Allow to schedule ICMP packets in IPVS, from Alex Gartrell.
2) Provide FIB table ID in ipv4 route dumps just as ipv6 does, from
David Ahern.
3) Allow the user to ask for the statistics to be filtered out of
ipv4/ipv6 address netlink dumps. From Sowmini Varadhan.
4) More work to pass the network namespace context around deep into
various packet path APIs, starting with the netfilter hooks. From
Eric W Biederman.
5) Add layer 2 TX/RX checksum offloading to qeth driver, from Thomas
Richter.
6) Use usec resolution for SYN/ACK RTTs in TCP, from Yuchung Cheng.
7) Support Very High Throughput in wireless MESH code, from Bob
Copeland.
8) Allow setting the ageing_time in switchdev/rocker. From Scott
Feldman.
9) Properly autoload L2TP type modules, from Stephen Hemminger.
10) Fix and enable offload features by default in 8139cp driver, from
David Woodhouse.
11) Support both ipv4 and ipv6 sockets in a single vxlan device, from
Jiri Benc.
12) Fix CWND limiting of thin streams in TCP, from Bendik Rønning
Opstad.
13) Fix IPSEC flowcache overflows on large systems, from Steffen
Klassert.
14) Convert bridging to track VLANs using rhashtable entries rather than
a bitmap. From Nikolay Aleksandrov.
15) Make TCP listener handling completely lockless, this is a major
accomplishment. Incoming request sockets now live in the
established hash table just like any other socket too.
From Eric Dumazet.
15) Provide more bridging attributes to netlink, from Nikolay
Aleksandrov.
16) Use hash based algorithm for ipv4 multipath routing, this was very
long overdue. From Peter Nørlund.
17) Several y2038 cures, mostly avoiding timespec. From Arnd Bergmann.
18) Allow non-root execution of EBPF programs, from Alexei Starovoitov.
19) Support SO_INCOMING_CPU as setsockopt, from Eric Dumazet. This
influences the port binding selection logic used by SO_REUSEPORT.
20) Add ipv6 support to VRF, from David Ahern.
21) Add support for Mellanox Spectrum switch ASIC, from Jiri Pirko.
22) Add rtl8xxxu Realtek wireless driver, from Jes Sorensen.
23) Implement RACK loss recovery in TCP, from Yuchung Cheng.
24) Support multipath routes in MPLS, from Roopa Prabhu.
25) Fix POLLOUT notification for listening sockets in AF_UNIX, from Eric
Dumazet.
26) Add new QED Qlogic river, from Yuval Mintz, Manish Chopra, and
Sudarsana Kalluru.
27) Don't fetch timestamps on AF_UNIX sockets, from Hannes Frederic
Sowa.
28) Support ipv6 geneve tunnels, from John W Linville.
29) Add flood control support to switchdev layer, from Ido Schimmel.
30) Fix CHECKSUM_PARTIAL handling of potentially fragmented frames, from
Hannes Frederic Sowa.
31) Support persistent maps and progs in bpf, from Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1790 commits)
sh_eth: use DMA barriers
switchdev: respect SKIP_EOPNOTSUPP flag in case there is no recursion
net: sched: kill dead code in sch_choke.c
irda: Delete an unnecessary check before the function call "irlmp_unregister_service"
net: dsa: mv88e6xxx: include DSA ports in VLANs
net: dsa: mv88e6xxx: disable SA learning for DSA and CPU ports
net/core: fix for_each_netdev_feature
vlan: Invoke driver vlan hooks only if device is present
arcnet/com20020: add LEDS_CLASS dependency
bpf, verifier: annotate verbose printer with __printf
dp83640: Only wait for timestamps for packets with timestamping enabled.
ptp: Change ptp_class to a proper bitmask
dp83640: Prune rx timestamp list before reading from it
dp83640: Delay scheduled work.
dp83640: Include hash in timestamp/packet matching
ipv6: fix tunnel error handling
net/mlx5e: Fix LSO vlan insertion
net/mlx5e: Re-eanble client vlan TX acceleration
net/mlx5e: Return error in case mlx5e_set_features() fails
net/mlx5e: Don't allow more than max supported channels
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- Rework the irqdomain core infrastructure to accomodate ACPI based
systems. This is required to support ARM64 without creating
artificial device tree nodes.
- Sanitize the ACPI based ARM GIC initialization by making use of the
new firmware independent irqdomain core
- Further improvements to the generic MSI management
- Generalize the irq migration on CPU hotplug
- Improvements to the threaded interrupt infrastructure
- Allow the migration of "chained" low level interrupt handlers
- Allow optional force masking of interrupts in disable_irq[_nosysnc]
- Support for two new interrupt chips - Sigh!
- A larger set of errata fixes for ARM gicv3
- The usual pile of fixes, updates, improvements and cleanups all
over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
Document that IRQ_NONE should be returned when IRQ not actually handled
PCI/MSI: Allow the MSI domain to be device-specific
PCI: Add per-device MSI domain hook
of/irq: Use the msi-map property to provide device-specific MSI domain
of/irq: Split of_msi_map_rid to reuse msi-map lookup
irqchip/gic-v3-its: Parse new version of msi-parent property
PCI/MSI: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Add support code for multi-parent version of "msi-parent"
irqchip/gic-v3-its: Add handling of PCI requester id.
PCI/MSI: Add helper function pci_msi_domain_get_msi_rid().
of/irq: Add new function of_msi_map_rid()
Docs: dt: Add PCI MSI map bindings
irqchip/gic-v2m: Add support for multiple MSI frames
irqchip/gic-v3: Fix translation of LPIs after conversion to irq_fwspec
irqchip/mxs: Add Alphascale ASM9260 support
irqchip/mxs: Prepare driver for hardware with different offsets
irqchip/mxs: Panic if ioremap or domain creation fails
irqdomain: Documentation updates
irqdomain/msi: Use fwnode instead of of_node
...
|
|
* pm-sleep:
PM / hibernate: fix a comment typo
input: i8042: Avoid resetting controller on system suspend/resume
PM / PCI / ACPI: Kick devices that might have been reset by firmware
PM / sleep: Add flags to indicate platform firmware involvement
PM / sleep: Drop pm_request_idle() from pm_generic_complete()
PCI / PM: Avoid resuming more devices during system suspend
PM / wakeup: wakeup_source_create: use kstrdup_const
PM / sleep: Report interrupt that caused system wakeup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
This is an incremental fix for a patch previously pulled from tip
irq/for-arm.
* 'irq/for-arm' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Make the cpuhotplug migration code less noisy
|
|
The original arm code has a pr_debug() statement for the case where
the irq chip has no set_affinity() callback. That's sufficient for
debugging and we really don't want to spam dmesg with useless warnings
for the normal case.
Fixes: f1e0bb0ad473: "genirq: Introduce generic irq migration for cpu hotunplug"
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Requested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
|
|
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|