| Age | Commit message (Collapse) | Author |
|---|
|
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Buffers powersave frame test is reversed in cfg80211, fix from Felix
Fietkau.
2) Remove bogus WARN_ON in openvswitch, from Jarno Rajahalme.
3) Fix some tg3 ethtool logic bugs, and one that would cause no
interrupts to be generated when rx-coalescing is set to 0. From
Satish Baddipadige and Siva Reddy Kallam.
4) QLCNIC mailbox corruption and napi budget handling fix from Manish
Chopra.
5) Fix fib_trie logic when walking the trie during /proc/net/route
output than can access a stale node pointer. From David Forster.
6) Several sctp_diag fixes from Phil Sutter.
7) PAUSE frame handling fixes in mlxsw driver from Ido Schimmel.
8) Checksum fixup fixes in bpf from Daniel Borkmann.
9) Memork leaks in nfnetlink, from Liping Zhang.
10) Use after free in rxrpc, from David Howells.
11) Use after free in new skb_array code of macvtap driver, from Jason
Wang.
12) Calipso resource leak, from Colin Ian King.
13) mediatek bug fixes (missing stats sync init, etc.) from Sean Wang.
14) Fix bpf non-linear packet write helpers, from Daniel Borkmann.
15) Fix lockdep splats in macsec, from Sabrina Dubroca.
16) hv_netvsc bug fixes from Vitaly Kuznetsov, mostly to do with VF
handling.
17) Various tc-action bug fixes, from CONG Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net_sched: allow flushing tc police actions
net_sched: unify the init logic for act_police
net_sched: convert tcf_exts from list to pointer array
net_sched: move tc offload macros to pkt_cls.h
net_sched: fix a typo in tc_for_each_action()
net_sched: remove an unnecessary list_del()
net_sched: remove the leftover cleanup_a()
mlxsw: spectrum: Allow packets to be trapped from any PG
mlxsw: spectrum: Unmap 802.1Q FID before destroying it
mlxsw: spectrum: Add missing rollbacks in error path
mlxsw: reg: Fix missing op field fill-up
mlxsw: spectrum: Trap loop-backed packets
mlxsw: spectrum: Add missing packet traps
mlxsw: spectrum: Mark port as active before registering it
mlxsw: spectrum: Create PVID vPort before registering netdevice
mlxsw: spectrum: Remove redundant errors from the code
mlxsw: spectrum: Don't return upon error in removal path
i40e: check for and deal with non-contiguous TCs
ixgbe: Re-enable ability to toggle VLAN filtering
ixgbe: Force VLNCTRL.VFE to be set in all VMDq paths
...
|
|
bpf_get_prandom_u32() was initially introduced for socket filters
and later requested numberous times to be added to tracing bpf programs
for the same reason as in socket filters: to be able to randomly
select incoming events.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The helper functions like bpf_map_lookup_elem(map, key) were only
allowing 'key' to point to the initialized stack area.
That is causing performance degradation when programs need to process
millions of packets per second and need to copy contents of the packet
into the stack just to pass the stack pointer into the lookup() function.
Allow such helpers read from the packet directly.
All helpers that expect ARG_PTR_TO_MAP_KEY, ARG_PTR_TO_MAP_VALUE,
ARG_PTR_TO_STACK assume byte aligned pointer, so no alignment concerns,
only need to check that helper will not be accessing beyond
the packet range verified by the prior 'if (ptr < data_end)' condition.
For now allow this feature for XDP programs only. Later it can be
relaxed for the clsact programs as well.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While hashing out BPF's current_task_under_cgroup helper bits, it came
to discussion that the skb_in_cgroup helper name was suboptimally chosen.
Tejun says:
So, I think in_cgroup should mean that the object is in that
particular cgroup while under_cgroup in the subhierarchy of that
cgroup. Let's rename the other subhierarchy test to under too. I
think that'd be a lot less confusing going forward.
[...]
It's more intuitive and gives us the room to implement the real
"in" test if ever necessary in the future.
Since this touches uapi bits, we need to change this as long as v4.8
is not yet officially released. Thus, change the helper enum and rename
related bits.
Fixes: 4a482f34afcc ("cgroup: bpf: Add bpf_skb_in_cgroup_proto")
Reference: http://patchwork.ozlabs.org/patch/658500/
Suggested-by: Sargun Dhillon <sargun@sargun.me>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
|
|
This adds a bpf helper that's similar to the skb_in_cgroup helper to check
whether the probe is currently executing in the context of a specific
subset of the cgroupsv2 hierarchy. It does this based on membership test
for a cgroup arraymap. It is invalid to call this in an interrupt, and
it'll return an error. The helper is primarily to be used in debugging
activities for containers, where you may have multiple programs running in
a given top-level "container".
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Two hibernation fixes allowing it to work with the recently added
randomization of the kernel identity mapping base on x86-64 and one
cpufreq driver regression fix.
Specifics:
- Fix the x86 identity mapping creation helpers to avoid the
assumption that the base address of the mapping will always be
aligned at the PGD level, as it may be aligned at the PUD level if
address space randomization is enabled (Rafael Wysocki).
- Fix the hibernation core to avoid executing tracing functions
before restoring the processor state completely during resume
(Thomas Garnier).
- Fix a recently introduced regression in the powernv cpufreq driver
that causes it to crash due to an out-of-bounds array access
(Akshay Adiga)"
* tag 'pm-4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / hibernate: Restore processor state before using per-CPU variables
x86/power/64: Always create temporary identity mapping correctly
cpufreq: powernv: Fix crash in gpstate_timer_handler()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"Misc fixes: a /dev/rtc regression fix, two APIC timer period
calibration fixes, an ARM clocksource driver fix and a NOHZ
power use regression fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/hpet: Fix /dev/rtc breakage caused by RTC cleanup
x86/timers/apic: Inform TSC deadline clockevent device about recalibration
x86/timers/apic: Fix imprecise timer interrupts by eliminating TSC clockevents frequency roundoff error
timers: Fix get_next_timer_interrupt() computation
clocksource/arm_arch_timer: Force per-CPU interrupt to be level-triggered
|
|
* pm-sleep:
PM / hibernate: Restore processor state before using per-CPU variables
x86/power/64: Always create temporary identity mapping correctly
* pm-cpufreq:
cpufreq: powernv: Fix crash in gpstate_timer_handler()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: cputime fixes, two deadline scheduler fixes and a cgroups
scheduling fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/cputime: Fix omitted ticks passed in parameter
sched/cputime: Fix steal time accounting
sched/deadline: Fix lock pinning warning during CPU hotplug
sched/cputime: Mitigate performance regression in times()/clock_gettime()
sched/fair: Fix typo in sync_throttle()
sched/deadline: Fix wrap-around in DL heap
|
|
Restore the processor state before calling any other functions to
ensure per-CPU variables can be used with KASLR memory randomization.
Tracing functions use per-CPU variables (GS based on x86) and one was
called just before restoring the processor state fully. It resulted
in a double fault when both the tracing & the exception handler
functions tried to use a per-CPU variable.
Fixes: bb3632c6101b (PM / sleep: trace events for suspend/resume)
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Reported-by: Jiri Kosina <jikos@kernel.org>
Tested-by: Rafael J. Wysocki <rafael@kernel.org>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Thomas Garnier <thgarnie@google.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, plus two uncore-PMU fixes, an uprobes fix, a
perf-cgroups fix and an AUX events fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Add enable_box for client MSR uncore
perf/x86/intel/uncore: Fix uncore num_counters
uprobes/x86: Fix RIP-relative handling of EVEX-encoded instructions
perf/core: Set cgroup in CPU contexts for new cgroup events
perf/core: Fix sideband list-iteration vs. event ordering NULL pointer deference crash
perf probe ppc64le: Fix probe location when using DWARF
perf probe: Add function to post process kernel trace events
tools: Sync cpufeatures headers with the kernel
toops: Sync tools/include/uapi/linux/bpf.h with the kernel
tools: Sync cpufeatures.h and vmx.h with the kernel
perf probe: Support signedness casting
perf stat: Avoid skew when reading events
perf probe: Fix module name matching
perf probe: Adjust map->reloc offset when finding kernel symbol from map
perf hists: Trim libtraceevent trace_seq buffers
perf script: Add 'bpf-output' field to usage message
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"Misc fixes: lockstat fix, futex fix on !MMU systems, big endian fix
for qrwlocks and a race fix for pvqspinlocks"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/pvqspinlock: Fix a bug in qstat_read()
locking/pvqspinlock: Fix double hash race
locking/qrwlock: Fix write unlock bug on big endian systems
futex: Assume all mappings are private on !MMU systems
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Ingo Molnar:
"A fix for an MSI regression"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi: Make sure PCI MSIs are activated early
|
|
Commit:
f9bcf1e0e014 ("sched/cputime: Fix steal time accounting")
... fixes a leak on steal time accounting but forgets to account
the ticks passed in parameters, assuming there is only one to
take into account.
Let's consider that parameter back.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Wanpeng Li <kernellwp@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Cc: linux-tip-commits@vger.kernel.org
Link: http://lkml.kernel.org/r/20160811125822.GB4214@lerouge
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit:
57430218317 ("sched/cputime: Count actually elapsed irq & softirq time")
... didn't take steal time into consideration with passing the noirqtime
kernel parameter.
As Paolo pointed out before:
| Why not? If idle=poll, for example, any time the guest is suspended (and
| thus cannot poll) does count as stolen time.
This patch fixes it by reducing steal time from idle time accounting when
the noirqtime parameter is true. The average idle time drops from 56.8%
to 54.75% for nohz idle kvm guest(noirqtime, idle=poll, four vCPUs running
on one pCPU).
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1470893795-3527-1-git-send-email-wanpeng.li@hotmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
It's obviously wrong to set stat to NULL. So lets remove it.
Otherwise it is always zero when we check the latency of kick/wake.
Signed-off-by: Pan Xinhui <xinhui.pan@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Waiman Long <Waiman.Long@hpe.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1468405414-3700-1-git-send-email-xinhui.pan@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When the lock holder vCPU is racing with the queue head:
CPU 0 (lock holder) CPU1 (queue head)
=================== =================
spin_lock(); spin_lock();
pv_kick_node(): pv_wait_head_or_lock():
if (!lp) {
lp = pv_hash(lock, pn);
xchg(&l->locked, _Q_SLOW_VAL);
}
WRITE_ONCE(pn->state, vcpu_halted);
cmpxchg(&pn->state,
vcpu_halted, vcpu_hashed);
WRITE_ONCE(l->locked, _Q_SLOW_VAL);
(void)pv_hash(lock, pn);
In this case, lock holder inserts the pv_node of queue head into the
hash table and set _Q_SLOW_VAL unnecessary. This patch avoids it by
restoring/setting vcpu_hashed state after failing adaptive locking
spinning.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Pan Xinhui <xinhui.pan@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <Waiman.Long@hpe.com>
Link: http://lkml.kernel.org/r/1468484156-4521-1-git-send-email-wanpeng.li@hotmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The following warning can be triggered by hot-unplugging the CPU
on which an active SCHED_DEADLINE task is running on:
WARNING: CPU: 0 PID: 0 at kernel/locking/lockdep.c:3531 lock_release+0x690/0x6a0
releasing a pinned lock
Call Trace:
dump_stack+0x99/0xd0
__warn+0xd1/0xf0
? dl_task_timer+0x1a1/0x2b0
warn_slowpath_fmt+0x4f/0x60
? sched_clock+0x13/0x20
lock_release+0x690/0x6a0
? enqueue_pushable_dl_task+0x9b/0xa0
? enqueue_task_dl+0x1ca/0x480
_raw_spin_unlock+0x1f/0x40
dl_task_timer+0x1a1/0x2b0
? push_dl_task.part.31+0x190/0x190
WARNING: CPU: 0 PID: 0 at kernel/locking/lockdep.c:3649 lock_unpin_lock+0x181/0x1a0
unpinning an unpinned lock
Call Trace:
dump_stack+0x99/0xd0
__warn+0xd1/0xf0
warn_slowpath_fmt+0x4f/0x60
lock_unpin_lock+0x181/0x1a0
dl_task_timer+0x127/0x2b0
? push_dl_task.part.31+0x190/0x190
As per the comment before this code, its safe to drop the RQ lock
here, and since we (potentially) change rq, unpin and repin to avoid
the splat.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
[ Rewrote changelog. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luca Abeni <luca.abeni@unitn.it>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1470274940-17976-1-git-send-email-wanpeng.li@hotmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Commit:
6e998916dfe3 ("sched/cputime: Fix clock_nanosleep()/clock_gettime() inconsistency")
fixed a problem whereby clock_nanosleep() followed by clock_gettime() could
allow a task to wake early. It addressed the problem by calling the scheduling
classes update_curr() when the cputimer starts.
Said change induced a considerable performance regression on the syscalls
times() and clock_gettimes(CLOCK_PROCESS_CPUTIME_ID). There are some
debuggers and applications that monitor their own performance that
accidentally depend on the performance of these specific calls.
This patch mitigates the performace loss by prefetching data in the CPU
cache, as stalls due to cache misses appear to be where most time is spent
in our benchmarks.
Here are the performance gain of this patch over v4.7-rc7 on a Sandy Bridge
box with 32 logical cores and 2 NUMA nodes. The test is repeated with a
variable number of threads, from 2 to 4*num_cpus; the results are in
seconds and correspond to the average of 10 runs; the percentage gain is
computed with (before-after)/before so a positive value is an improvement
(it's faster). The improvement varies between a few percents for 5-20
threads and more than 10% for 2 or >20 threads.
pound_clock_gettime:
threads 4.7-rc7 patched 4.7-rc7
[num] [secs] [secs (percent)]
2 3.48 3.06 ( 11.83%)
5 3.33 3.25 ( 2.40%)
8 3.37 3.26 ( 3.30%)
12 3.32 3.37 ( -1.60%)
21 4.01 3.90 ( 2.74%)
30 3.63 3.36 ( 7.41%)
48 3.71 3.11 ( 16.27%)
79 3.75 3.16 ( 15.74%)
110 3.81 3.25 ( 14.80%)
128 3.88 3.31 ( 14.76%)
pound_times:
threads 4.7-rc7 patched 4.7-rc7
[num] [secs] [secs (percent)]
2 3.65 3.25 ( 11.03%)
5 3.45 3.17 ( 7.92%)
8 3.52 3.22 ( 8.69%)
12 3.29 3.36 ( -2.04%)
21 4.07 3.92 ( 3.78%)
30 3.87 3.40 ( 12.17%)
48 3.79 3.16 ( 16.61%)
79 3.88 3.28 ( 15.42%)
110 3.90 3.38 ( 13.35%)
128 4.00 3.38 ( 15.45%)
pound_clock_gettime and pound_clock_gettime are two benchmarks included in
the MMTests framework. They launch a given number of threads which
repeatedly call times() or clock_gettimes(). The results above can be
reproduced with cloning MMTests from github.com and running the "poundtime"
workload:
$ git clone https://github.com/gormanm/mmtests.git
$ cd mmtests
$ cp configs/config-global-dhp__workload_poundtime config
$ ./run-mmtests.sh --run-monitor $(uname -r)
The above will run "poundtime" measuring the kernel currently running on
the machine; Once a new kernel is installed and the machine rebooted,
running again
$ cd mmtests
$ ./run-mmtests.sh --run-monitor $(uname -r)
will produce results to compare with. A comparison table will be output
with:
$ cd mmtests/work/log
$ ../../compare-kernels.sh
the table will contain a lot of entries; grepping for "Amean" (as in
"arithmetic mean") will give the tables presented above. The source code
for the two benchmarks is reported at the end of this changelog for
clairity.
The cache misses addressed by this patch were found using a combination of
`perf top`, `perf record` and `perf annotate`. The incriminated lines were
found to be
struct sched_entity *curr = cfs_rq->curr;
and
delta_exec = now - curr->exec_start;
in the function update_curr() from kernel/sched/fair.c. This patch
prefetches the data from memory just before update_curr is called in the
interested execution path.
A comparison of the total number of cycles before and after the patch
follows; the data is obtained using `perf stat -r 10 -ddd <program>`
running over the same sequence of number of threads used above (a positive
gain is an improvement):
threads cycles before cycles after gain
2 19,699,563,964 +-1.19% 17,358,917,517 +-1.85% 11.88%
5 47,401,089,566 +-2.96% 45,103,730,829 +-0.97% 4.85%
8 80,923,501,004 +-3.01% 71,419,385,977 +-0.77% 11.74%
12 112,326,485,473 +-0.47% 110,371,524,403 +-0.47% 1.74%
21 193,455,574,299 +-0.72% 180,120,667,904 +-0.36% 6.89%
30 315,073,519,013 +-1.64% 271,222,225,950 +-1.29% 13.92%
48 321,969,515,332 +-1.48% 273,353,977,321 +-1.16% 15.10%
79 337,866,003,422 +-0.97% 289,462,481,538 +-1.05% 14.33%
110 338,712,691,920 +-0.78% 290,574,233,170 +-0.77% 14.21%
128 348,384,794,006 +-0.50% 292,691,648,206 +-0.66% 15.99%
A comparison of cache miss vs total cache loads ratios, before and after
the patch (again from the `perf stat -r 10 -ddd <program>` tables):
threads L1 misses/total*100 L1 misses/total*100 gain
before after
2 7.43 +-4.90% 7.36 +-4.70% 0.94%
5 13.09 +-4.74% 13.52 +-3.73% -3.28%
8 13.79 +-5.61% 12.90 +-3.27% 6.45%
12 11.57 +-2.44% 8.71 +-1.40% 24.72%
21 12.39 +-3.92% 9.97 +-1.84% 19.53%
30 13.91 +-2.53% 11.73 +-2.28% 15.67%
48 13.71 +-1.59% 12.32 +-1.97% 10.14%
79 14.44 +-0.66% 13.40 +-1.06% 7.20%
110 15.86 +-0.50% 14.46 +-0.59% 8.83%
128 16.51 +-0.32% 15.06 +-0.78% 8.78%
As a final note, the following shows the evolution of performance figures
in the "poundtime" benchmark and pinpoints commit 6e998916dfe3
("sched/cputime: Fix clock_nanosleep()/clock_gettime() inconsistency") as a
major source of degradation, mostly unaddressed to this day (figures
expressed in seconds).
pound_clock_gettime:
threads parent of 6e998916dfe3 4.7-rc7
6e998916dfe3 itself
2 2.23 3.68 ( -64.56%) 3.48 (-55.48%)
5 2.83 3.78 ( -33.42%) 3.33 (-17.43%)
8 2.84 4.31 ( -52.12%) 3.37 (-18.76%)
12 3.09 3.61 ( -16.74%) 3.32 ( -7.17%)
21 3.14 4.63 ( -47.36%) 4.01 (-27.71%)
30 3.28 5.75 ( -75.37%) 3.63 (-10.80%)
48 3.02 6.05 (-100.56%) 3.71 (-22.99%)
79 2.88 6.30 (-118.90%) 3.75 (-30.26%)
110 2.95 6.46 (-119.00%) 3.81 (-29.24%)
128 3.05 6.42 (-110.08%) 3.88 (-27.04%)
pound_times:
threads parent of 6e998916dfe3 4.7-rc7
6e998916dfe3 itself
2 2.27 3.73 ( -64.71%) 3.65 (-61.14%)
5 2.78 3.77 ( -35.56%) 3.45 (-23.98%)
8 2.79 4.41 ( -57.71%) 3.52 (-26.05%)
12 3.02 3.56 ( -17.94%) 3.29 ( -9.08%)
21 3.10 4.61 ( -48.74%) 4.07 (-31.34%)
30 3.33 5.75 ( -72.53%) 3.87 (-16.01%)
48 2.96 6.06 (-105.04%) 3.79 (-28.10%)
79 2.88 6.24 (-116.83%) 3.88 (-34.81%)
110 2.98 6.37 (-114.08%) 3.90 (-31.12%)
128 3.10 6.35 (-104.61%) 4.00 (-28.87%)
The source code of the two benchmarks follows. To compile the two:
NR_THREADS=42
for FILE in pound_times pound_clock_gettime; do
gcc -lrt -O2 -lpthread -DNUM_THREADS=$NR_THREADS $FILE.c -o $FILE
done
==== BEGIN pound_times.c ====
struct tms start;
void *pound (void *threadid)
{
struct tms end;
int oldutime = 0;
int utime;
int i;
for (i = 0; i < 5000000 / NUM_THREADS; i++) {
times(&end);
utime = ((int)end.tms_utime - (int)start.tms_utime);
if (oldutime > utime) {
printf("utime decreased, was %d, now %d!\n", oldutime, utime);
}
oldutime = utime;
}
pthread_exit(NULL);
}
int main()
{
pthread_t th[NUM_THREADS];
long i;
times(&start);
for (i = 0; i < NUM_THREADS; i++) {
pthread_create (&th[i], NULL, pound, (void *)i);
}
pthread_exit(NULL);
return 0;
}
==== END pound_times.c ====
==== BEGIN pound_clock_gettime.c ====
void *pound (void *threadid)
{
struct timespec ts;
int rc, i;
unsigned long prev = 0, this = 0;
for (i = 0; i < 5000000 / NUM_THREADS; i++) {
rc = clock_gettime(CLOCK_PROCESS_CPUTIME_ID, &ts);
if (rc < 0)
perror("clock_gettime");
this = (ts.tv_sec * 1000000000) + ts.tv_nsec;
if (0 && this < prev)
printf("%lu ns timewarp at iteration %d\n", prev - this, i);
prev = this;
}
pthread_exit(NULL);
}
int main()
{
pthread_t th[NUM_THREADS];
long rc, i;
pid_t pgid;
for (i = 0; i < NUM_THREADS; i++) {
rc = pthread_create(&th[i], NULL, pound, (void *)i);
if (rc < 0)
perror("pthread_create");
}
pthread_exit(NULL);
return 0;
}
==== END pound_clock_gettime.c ====
Suggested-by: Mike Galbraith <mgalbraith@suse.de>
Signed-off-by: Giovanni Gherdovich <ggherdovich@suse.cz>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1470385316-15027-2-git-send-email-ggherdovich@suse.cz
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We should update cfs_rq->throttled_clock_task, not
pcfs_rq->throttle_clock_task.
The effects of this bug was probably occasionally erratic
group scheduling, particularly in cgroups-intense workloads.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
[ Added changelog. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 55e16d30bd99 ("sched/fair: Rework throttle_count sync")
Link: http://lkml.kernel.org/r/1468050862-18864-1-git-send-email-xlpang@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Current code in cpudeadline.c has a bug in re-heapifying when adding a
new element at the end of the heap, because a deadline value of 0 is
temporarily set in the new elem, then cpudl_change_key() is called
with the actual elem deadline as param.
However, the function compares the new deadline to set with the one
previously in the elem, which is 0. So, if current absolute deadlines
grew so much to have negative values as s64, the comparison in
cpudl_change_key() makes the wrong decision. Instead, as from
dl_time_before(), the kernel should handle correctly abs deadlines
wrap-arounds.
This patch fixes the problem with a minimally invasive change that
forces cpudl_change_key() to heapify up in this case.
Signed-off-by: Tommaso Cucinotta <tommaso.cucinotta@sssup.it>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Luca Abeni <luca.abeni@unitn.it>
Cc: Juri Lelli <juri.lelli@arm.com>
Cc: Juri Lelli <juri.lelli@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1468921493-10054-2-git-send-email-tommaso.cucinotta@sssup.it
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There's a perf stat bug easy to observer on a machine with only one cgroup:
$ perf stat -e cycles -I 1000 -C 0 -G /
# time counts unit events
1.000161699 <not counted> cycles /
2.000355591 <not counted> cycles /
3.000565154 <not counted> cycles /
4.000951350 <not counted> cycles /
We'd expect some output there.
The underlying problem is that there is an optimization in
perf_cgroup_sched_{in,out}() that skips the switch of cgroup events
if the old and new cgroups in a task switch are the same.
This optimization interacts with the current code in two ways
that cause a CPU context's cgroup (cpuctx->cgrp) to be NULL even if a
cgroup event matches the current task. These are:
1. On creation of the first cgroup event in a CPU: In current code,
cpuctx->cpu is only set in perf_cgroup_sched_in, but due to the
aforesaid optimization, perf_cgroup_sched_in will run until the next
cgroup switches in that CPU. This may happen late or never happen,
depending on system's number of cgroups, CPU load, etc.
2. On deletion of the last cgroup event in a cpuctx: In list_del_event,
cpuctx->cgrp is set NULL. Any new cgroup event will not be sched in
because cpuctx->cgrp == NULL until a cgroup switch occurs and
perf_cgroup_sched_in is executed (updating cpuctx->cgrp).
This patch fixes both problems by setting cpuctx->cgrp in list_add_event,
mirroring what list_del_event does when removing a cgroup event from CPU
context, as introduced in:
commit 68cacd29167b ("perf_events: Fix stale ->cgrp pointer in update_cgrp_time_from_cpuctx()")
With this patch, cpuctx->cgrp is always set/clear when installing/removing
the first/last cgroup event in/from the CPU context. With cpuctx->cgrp
correctly set, event_filter_match works as intended when events are
sched in/out.
After the fix, the output is as expected:
$ perf stat -e cycles -I 1000 -a -G /
# time counts unit events
1.004699159 627342882 cycles /
2.007397156 615272690 cycles /
3.010019057 616726074 cycles /
Signed-off-by: David Carrillo-Cisneros <davidcc@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1470124092-113192-1-git-send-email-davidcc@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
deference crash
Vegard Nossum reported that perf fuzzing generates a NULL
pointer dereference crash:
> Digging a bit deeper into this, it seems the event itself is getting
> created by perf_event_open() and it gets added to the pmu_event_list
> through:
>
> perf_event_open()
> - perf_event_alloc()
> - account_event()
> - account_pmu_sb_event()
> - attach_sb_event()
>
> so at this point the event is being attached but its ->ctx is still
> NULL. It seems like ->ctx is set just a bit later in
> perf_event_open(), though.
>
> But before that, __schedule() comes along and creates a stack trace
> similar to the one above:
>
> __schedule()
> - __perf_event_task_sched_out()
> - perf_iterate_sb()
> - perf_iterate_sb_cpu()
> - event_filter_match()
> - perf_cgroup_match()
> - __get_cpu_context()
> - (dereference ctx which is NULL)
>
> So I guess the question is... should the event be attached (= put on
> the list) before ->ctx gets set? Or should the cgroup code check for a
> NULL ->ctx?
The latter seems like the simplest solution. Moving the list-add later
creates a bit of a mess.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Tested-by: Vegard Nossum <vegard.nossum@gmail.com>
Tested-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Carrillo-Cisneros <davidcc@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: f2fb6bef9251 ("perf/core: Optimize side-band event delivery")
Link: http://lkml.kernel.org/r/20160804123724.GN6862@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This reverts commit 874f9c7da9a4acbc1b9e12ca722579fb50e4d142.
Geert Uytterhoeven reports:
"This change seems to have an (unintendent?) side-effect.
Before, pr_*() calls without a trailing newline characters would be
printed with a newline character appended, both on the console and in
the output of the dmesg command.
After this commit, no new line character is appended, and the output
of the next pr_*() call of the same type may be appended, like in:
- Truncating RAM at 0x0000000040000000-0x00000000c0000000 to -0x0000000070000000
- Ignoring RAM at 0x0000000200000000-0x0000000240000000 (!CONFIG_HIGHMEM)
+ Truncating RAM at 0x0000000040000000-0x00000000c0000000 to -0x0000000070000000Ignoring RAM at 0x0000000200000000-0x0000000240000000 (!CONFIG_HIGHMEM)"
Joe Perches says:
"No, that is not intentional.
The newline handling code inside vprintk_emit is a bit involved and
for now I suggest a revert until this has all the same behavior as
earlier"
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Requested-by: Joe Perches <joe@perches.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The tick_nohz_stop_sched_tick() routine is not properly
canceling the sched timer when nothing is pending, because
get_next_timer_interrupt() is no longer returning KTIME_MAX in
that case. This causes periodic interrupts when none are needed.
When determining the next interrupt time, we first use
__next_timer_interrupt() to get the first expiring timer in the
timer wheel. If no timer is found, we return the base clock value
plus NEXT_TIMER_MAX_DELTA to indicate there is no timer in the
timer wheel.
Back in get_next_timer_interrupt(), we set the "expires" value
by converting the timer wheel expiry (in ticks) to a nsec value.
But we don't want to do this if the timer wheel expiry value
indicates no timer; we want to return KTIME_MAX.
Prior to commit 500462a9de65 ("timers: Switch to a non-cascading
wheel") we checked base->active_timers to see if any timers
were active, and if not, we didn't touch the expiry value and so
properly returned KTIME_MAX. Now we don't have active_timers.
To fix this, we now just check the timer wheel expiry value to
see if it is "now + NEXT_TIMER_MAX_DELTA", and if it is, we don't
try to compute a new value based on it, but instead simply let the
KTIME_MAX value in expires remain.
Fixes: 500462a9de65 "timers: Switch to a non-cascading wheel"
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/1470688147-22287-1-git-send-email-cmetcalf@mellanox.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Bharat Kumar Gogada reported issues with the generic MSI code, where the
end-point ended up with garbage in its MSI configuration (both for the vector
and the message).
It turns out that the two MSI paths in the kernel are doing slightly different
things:
generic MSI: disable MSI -> allocate MSI -> enable MSI -> setup EP
PCI MSI: disable MSI -> allocate MSI -> setup EP -> enable MSI
And it turns out that end-points are allowed to latch the content of the MSI
configuration registers as soon as MSIs are enabled. In Bharat's case, the
end-point ends up using whatever was there already, which is not what you
want.
In order to make things converge, we introduce a new MSI domain flag
(MSI_FLAG_ACTIVATE_EARLY) that is unconditionally set for PCI/MSI. When set,
this flag forces the programming of the end-point as soon as the MSIs are
allocated.
A consequence of this is that we have an extra activate in irq_startup, but
that should be without much consequence.
tglx:
- Several people reported a VMWare regression with PCI/MSI-X passthrough. It
turns out that the patch also cures that issue.
- We need to have a look at the MSI disable interrupt path, where we write
the msg to all zeros without disabling MSI in the PCI device. Is that
correct?
Fixes: 52f518a3a7c2 "x86/MSI: Use hierarchical irqdomains to manage MSI interrupts"
Reported-and-tested-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Reported-and-tested-by: Foster Snowhill <forst@forstwoof.ru>
Reported-by: Matthias Prager <linux@matthiasprager.de>
Reported-by: Jason Taylor <jason.taylor@simplivity.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1468426713-31431-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
In commit 874f9c7da9a4 ("printk: create pr_<level> functions"), new
pr_level defines were added to printk.c.
These new defines are guarded by an #ifdef CONFIG_PRINTK - however,
there is already a surrounding #ifdef CONFIG_PRINTK starting a lot
earlier in line 249 which means the newly introduced #ifdef is
unnecessary.
Let's remove it to avoid confusion.
Signed-off-by: Andreas Ziegler <andreas.ziegler@fau.de>
Cc: Joe Perches <joe@perches.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since commit 63a4cc24867d, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The introduction of pre-allocated hash elements inadvertently broke
the behavior of bpf hash maps where users expected to call
bpf_map_update_elem() without considering that the map can be full.
Some programs do:
old_value = bpf_map_lookup_elem(map, key);
if (old_value) {
... prepare new_value on stack ...
bpf_map_update_elem(map, key, new_value);
}
Before pre-alloc the update() for existing element would work even
in 'map full' condition. Restore this behavior.
The above program could have updated old_value in place instead of
update() which would be faster and most programs use that approach,
but sometimes the values are large and the programs use update()
helper to do atomic replacement of the element.
Note we cannot simply update element's value in-place like percpu
hash map does and have to allocate extra num_possible_cpu elements
and use this extra reserve when the map is full.
Fixes: 6c9059817432 ("bpf: pre-allocate hash map elements")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf updates from Ingo Molnar:
"Mostly tooling fixes and some late tooling updates, plus two perf
related printk message fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tests bpf: Use SyS_epoll_wait alias
perf tests: objdump output can contain multi byte chunks
perf record: Add --sample-cpu option
perf hists: Introduce output_resort_cb method
perf tools: Move config/Makefile into Makefile.config
perf tests: Add test for bitmap_scnprintf function
tools lib: Add bitmap_and function
tools lib: Add bitmap_scnprintf function
tools lib: Add bitmap_alloc function
tools lib traceevent: Ignore generated library files
perf tools: Fix build failure on perl script context
perf/core: Change log level for duration warning to KERN_INFO
perf annotate: Plug filename string leak
perf annotate: Introduce strerror for handling symbol__disassemble() errors
perf annotate: Rename symbol__annotate() to symbol__disassemble()
perf/x86: Modify error message in virtualized environment
perf target: str_error_r() always returns the buffer it receives
perf annotate: Use pipe + fork instead of popen
perf evsel: Introduce constructor for cycles event
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull more powerpc updates from Michael Ellerman:
"These were delayed for various reasons, so I let them sit in next a
bit longer, rather than including them in my first pull request.
Fixes:
- Fix early access to cpu_spec relocation from Benjamin Herrenschmidt
- Fix incorrect event codes in power9-event-list from Madhavan Srinivasan
- Move register_process_table() out of ppc_md from Michael Ellerman
Use jump_label use for [cpu|mmu]_has_feature():
- Add mmu_early_init_devtree() from Michael Ellerman
- Move disable_radix handling into mmu_early_init_devtree() from Michael Ellerman
- Do hash device tree scanning earlier from Michael Ellerman
- Do radix device tree scanning earlier from Michael Ellerman
- Do feature patching before MMU init from Michael Ellerman
- Check features don't change after patching from Michael Ellerman
- Make MMU_FTR_RADIX a MMU family feature from Aneesh Kumar K.V
- Convert mmu_has_feature() to returning bool from Michael Ellerman
- Convert cpu_has_feature() to returning bool from Michael Ellerman
- Define radix_enabled() in one place & use static inline from Michael Ellerman
- Add early_[cpu|mmu]_has_feature() from Michael Ellerman
- Convert early cpu/mmu feature check to use the new helpers from Aneesh Kumar K.V
- jump_label: Make it possible for arches to invoke jump_label_init() earlier from Kevin Hao
- Call jump_label_init() in apply_feature_fixups() from Aneesh Kumar K.V
- Remove mfvtb() from Kevin Hao
- Move cpu_has_feature() to a separate file from Kevin Hao
- Add kconfig option to use jump labels for cpu/mmu_has_feature() from Michael Ellerman
- Add option to use jump label for cpu_has_feature() from Kevin Hao
- Add option to use jump label for mmu_has_feature() from Kevin Hao
- Catch usage of cpu/mmu_has_feature() before jump label init from Aneesh Kumar K.V
- Annotate jump label assembly from Michael Ellerman
TLB flush enhancements from Aneesh Kumar K.V:
- radix: Implement tlb mmu gather flush efficiently
- Add helper for finding SLBE LLP encoding
- Use hugetlb flush functions
- Drop multiple definition of mm_is_core_local
- radix: Add tlb flush of THP ptes
- radix: Rename function and drop unused arg
- radix/hugetlb: Add helper for finding page size
- hugetlb: Add flush_hugetlb_tlb_range
- remove flush_tlb_page_nohash
Add new ptrace regsets from Anshuman Khandual and Simon Guo:
- elf: Add powerpc specific core note sections
- Add the function flush_tmregs_to_thread
- Enable in transaction NT_PRFPREG ptrace requests
- Enable in transaction NT_PPC_VMX ptrace requests
- Enable in transaction NT_PPC_VSX ptrace requests
- Adapt gpr32_get, gpr32_set functions for transaction
- Enable support for NT_PPC_CGPR
- Enable support for NT_PPC_CFPR
- Enable support for NT_PPC_CVMX
- Enable support for NT_PPC_CVSX
- Enable support for TM SPR state
- Enable NT_PPC_TM_CTAR, NT_PPC_TM_CPPR, NT_PPC_TM_CDSCR
- Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR
- Enable support for EBB registers
- Enable support for Performance Monitor registers"
* tag 'powerpc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (48 commits)
powerpc/mm: Move register_process_table() out of ppc_md
powerpc/perf: Fix incorrect event codes in power9-event-list
powerpc/32: Fix early access to cpu_spec relocation
powerpc/ptrace: Enable support for Performance Monitor registers
powerpc/ptrace: Enable support for EBB registers
powerpc/ptrace: Enable support for NT_PPPC_TAR, NT_PPC_PPR, NT_PPC_DSCR
powerpc/ptrace: Enable NT_PPC_TM_CTAR, NT_PPC_TM_CPPR, NT_PPC_TM_CDSCR
powerpc/ptrace: Enable support for TM SPR state
powerpc/ptrace: Enable support for NT_PPC_CVSX
powerpc/ptrace: Enable support for NT_PPC_CVMX
powerpc/ptrace: Enable support for NT_PPC_CFPR
powerpc/ptrace: Enable support for NT_PPC_CGPR
powerpc/ptrace: Adapt gpr32_get, gpr32_set functions for transaction
powerpc/ptrace: Enable in transaction NT_PPC_VSX ptrace requests
powerpc/ptrace: Enable in transaction NT_PPC_VMX ptrace requests
powerpc/ptrace: Enable in transaction NT_PRFPREG ptrace requests
powerpc/process: Add the function flush_tmregs_to_thread
elf: Add powerpc specific core note sections
powerpc/mm: remove flush_tlb_page_nohash
powerpc/mm/hugetlb: Add flush_hugetlb_tlb_range
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"The only interesting thing here is Jessica's patch to add
ro_after_init support to modules. The rest are all trivia"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
extable.h: add stddef.h so "NULL" definition is not implicit
modules: add ro_after_init support
jump_label: disable preemption around __module_text_address().
exceptions: fork exception table content from module.h into extable.h
modules: Add kernel parameter to blacklist modules
module: Do a WARN_ON_ONCE() for assert module mutex not held
Documentation/module-signing.txt: Note need for version info if reusing a key
module: Invalidate signatures on force-loaded modules
module: Issue warnings when tainting kernel
module: fix redundant test.
module: fix noreturn attribute for __module_put_and_exit()
|
|
The current jump_label.h includes bug.h for things such as WARN_ON().
This makes the header problematic for inclusion by kernel.h or any
headers that kernel.h includes, since bug.h includes kernel.h (circular
dependency). The inclusion of atomic.h is similarly problematic. Thus,
this should make jump_label.h 'includable' from most places.
Link: http://lkml.kernel.org/r/7060ce35ddd0d20b33bf170685e6b0fab816bdf2.1467837322.git.jbaron@akamai.com
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Joe Perches <joe@perches.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add ro_after_init support for modules by adding a new page-aligned section
in the module layout (after rodata) for ro_after_init data and enabling RO
protection for that section after module init runs.
Signed-off-by: Jessica Yu <jeyu@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Steven reported a warning caused by not holding module_mutex or
rcu_read_lock_sched: his backtrace was corrupted but a quick audit
found this possible cause. It's wrong anyway...
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Blacklisting a module in linux has long been a problem. The current
procedure is to use rd.blacklist=module_name, however, that doesn't
cover the case after the initramfs and before a boot prompt (where one
is supposed to use /etc/modprobe.d/blacklist.conf to blacklist
runtime loading). Using rd.shell to get an early prompt is hit-or-miss,
and doesn't cover all situations AFAICT.
This patch adds this functionality of permanently blacklisting a module
by its name via the kernel parameter module_blacklist=module_name.
[v2]: Rusty, use core_param() instead of __setup() which simplifies
things.
[v3]: Rusty, undo wreckage from strsep()
[v4]: Rusty, simpler version of blacklisted()
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
When running with lockdep enabled, I triggered the WARN_ON() in the
module code that asserts when module_mutex or rcu_read_lock_sched are
not held. The issue I have is that this can also be called from the
dump_stack() code, causing us to enter an infinite loop...
------------[ cut here ]------------
WARNING: CPU: 1 PID: 0 at kernel/module.c:268 module_assert_mutex_or_preempt+0x3c/0x3e
Modules linked in: ip6t_REJECT nf_reject_ipv6 nf_conntrack_ipv6
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.7.0-rc3-test-00013-g501c2375253c #14
Hardware name: MSI MS-7823/CSM-H87M-G43 (MS-7823), BIOS V1.6 02/22/2014
ffff880215e8fa70 ffff880215e8fa70 ffffffff812fc8e3 0000000000000000
ffffffff81d3e55b ffff880215e8fac0 ffffffff8104fc88 ffffffff8104fcab
0000000915e88300 0000000000000046 ffffffffa019b29a 0000000000000001
Call Trace:
[<ffffffff812fc8e3>] dump_stack+0x67/0x90
[<ffffffff8104fc88>] __warn+0xcb/0xe9
[<ffffffff8104fcab>] ? warn_slowpath_null+0x5/0x1f
------------[ cut here ]------------
WARNING: CPU: 1 PID: 0 at kernel/module.c:268 module_assert_mutex_or_preempt+0x3c/0x3e
Modules linked in: ip6t_REJECT nf_reject_ipv6 nf_conntrack_ipv6
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.7.0-rc3-test-00013-g501c2375253c #14
Hardware name: MSI MS-7823/CSM-H87M-G43 (MS-7823), BIOS V1.6 02/22/2014
ffff880215e8f7a0 ffff880215e8f7a0 ffffffff812fc8e3 0000000000000000
ffffffff81d3e55b ffff880215e8f7f0 ffffffff8104fc88 ffffffff8104fcab
0000000915e88300 0000000000000046 ffffffffa019b29a 0000000000000001
Call Trace:
[<ffffffff812fc8e3>] dump_stack+0x67/0x90
[<ffffffff8104fc88>] __warn+0xcb/0xe9
[<ffffffff8104fcab>] ? warn_slowpath_null+0x5/0x1f
------------[ cut here ]------------
WARNING: CPU: 1 PID: 0 at kernel/module.c:268 module_assert_mutex_or_preempt+0x3c/0x3e
Modules linked in: ip6t_REJECT nf_reject_ipv6 nf_conntrack_ipv6
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.7.0-rc3-test-00013-g501c2375253c #14
Hardware name: MSI MS-7823/CSM-H87M-G43 (MS-7823), BIOS V1.6 02/22/2014
ffff880215e8f4d0 ffff880215e8f4d0 ffffffff812fc8e3 0000000000000000
ffffffff81d3e55b ffff880215e8f520 ffffffff8104fc88 ffffffff8104fcab
0000000915e88300 0000000000000046 ffffffffa019b29a 0000000000000001
Call Trace:
[<ffffffff812fc8e3>] dump_stack+0x67/0x90
[<ffffffff8104fc88>] __warn+0xcb/0xe9
[<ffffffff8104fcab>] ? warn_slowpath_null+0x5/0x1f
------------[ cut here ]------------
WARNING: CPU: 1 PID: 0 at kernel/module.c:268 module_assert_mutex_or_preempt+0x3c/0x3e
[...]
Which gives us rather useless information. Worse yet, there's some race
that causes this, and I seldom trigger it, so I have no idea what
happened.
This would not be an issue if that warning was a WARN_ON_ONCE().
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Using per-register incrementing ID can lead to
find_good_pkt_pointers() confusing registers which
have completely different values. Consider example:
0: (bf) r6 = r1
1: (61) r8 = *(u32 *)(r6 +76)
2: (61) r0 = *(u32 *)(r6 +80)
3: (bf) r7 = r8
4: (07) r8 += 32
5: (2d) if r8 > r0 goto pc+9
R0=pkt_end R1=ctx R6=ctx R7=pkt(id=0,off=0,r=32) R8=pkt(id=0,off=32,r=32) R10=fp
6: (bf) r8 = r7
7: (bf) r9 = r7
8: (71) r1 = *(u8 *)(r7 +0)
9: (0f) r8 += r1
10: (71) r1 = *(u8 *)(r7 +1)
11: (0f) r9 += r1
12: (07) r8 += 32
13: (2d) if r8 > r0 goto pc+1
R0=pkt_end R1=inv56 R6=ctx R7=pkt(id=0,off=0,r=32) R8=pkt(id=1,off=32,r=32) R9=pkt(id=1,off=0,r=32) R10=fp
14: (71) r1 = *(u8 *)(r9 +16)
15: (b7) r7 = 0
16: (bf) r0 = r7
17: (95) exit
We need to get a UNKNOWN_VALUE with imm to force id
generation so lines 0-5 make r7 a valid packet pointer.
We then read two different bytes from the packet and
add them to copies of the constructed packet pointer.
r8 (line 9) and r9 (line 11) will get the same id of 1,
independently. When either of them is validated (line
13) - find_good_pkt_pointers() will also mark the other
as safe. This leads to access on line 14 being mistakenly
considered safe.
Fixes: 969bf05eb3ce ("bpf: direct packet access")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"A few updates and fixes:
- move the suppressing of the __builtin_return_address >0 warning to
the tracing directory only.
- metag recordmcount fix for newer glibc's
- two tracing histogram fixes that were reported by KASAN"
* tag 'trace-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix use-after-free in hist_register_trigger()
tracing: Fix use-after-free in hist_unreg_all/hist_enable_unreg_all
Makefile: Mute warning for __builtin_return_address(>0) for tracing only
ftrace/recordmcount: Work around for addition of metag magic but not relocations
|
|
Copy the config fragments from the AOSP common kernel android-4.4
branch. It is becoming possible to run mainline kernels with Android,
but the kernel defconfigs don't work as-is and debugging missing config
options is a pain. Adding the config fragments into the kernel tree,
makes configuring a mainline kernel as simple as:
make ARCH=arm multi_v7_defconfig android-base.config android-recommended.config
The following non-upstream config options were removed:
CONFIG_NETFILTER_XT_MATCH_QTAGUID
CONFIG_NETFILTER_XT_MATCH_QUOTA2
CONFIG_NETFILTER_XT_MATCH_QUOTA2_LOG
CONFIG_PPPOLAC
CONFIG_PPPOPNS
CONFIG_SECURITY_PERF_EVENTS_RESTRICT
CONFIG_USB_CONFIGFS_F_MTP
CONFIG_USB_CONFIGFS_F_PTP
CONFIG_USB_CONFIGFS_F_ACC
CONFIG_USB_CONFIGFS_F_AUDIO_SRC
CONFIG_USB_CONFIGFS_UEVENT
CONFIG_INPUT_KEYCHORD
CONFIG_INPUT_KEYRESET
Link: http://lkml.kernel.org/r/1466708235-28593-1-git-send-email-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Dmitry Shmidt <dimitrysh@google.com>
Cc: Rom Lemarchand <romlem@android.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 20d8b67c06fa ("relay: add buffer-only channels; useful for early
logging") added support to use channels with no associated files.
This is useful when the exact location of relay file is not known or the
the parent directory of relay file is not available, while creating the
channel and the logging has to start right from the boot.
But there was no provision to use global mode with buffer-only channels,
which is added by this patch, without modifying the interface where
initially there will be a dummy invocation of create_buf_file callback
through which kernel client can convey the need of a global buffer.
For the use case where drivers/kernel clients want a simple interface
for the userspace, which enables them to capture data/logs from relay
file inorder & without any post processing, support of Global buffer
mode is warranted.
Modules, like i915, using relay_open() in early init would have to later
register their buffer-only relays, once debugfs is available, by calling
relay_late_setup_files(). Hence relay_late_setup_files() symbol also
needs to be exported.
Link: http://lkml.kernel.org/r/1468404563-11653-1-git-send-email-akash.goel@intel.com
Signed-off-by: Akash Goel <akash.goel@intel.com>
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I hit the following issue when run trinity in my system. The kernel is
3.4 version, but mainline has the same issue.
The root cause is that the segment size is too large so the kerenl
spends too long trying to allocate a page. Other cases will block until
the test case quits. Also, OOM conditions will occur.
Call Trace:
__alloc_pages_nodemask+0x14c/0x8f0
alloc_pages_current+0xaf/0x120
kimage_alloc_pages+0x10/0x60
kimage_alloc_control_pages+0x5d/0x270
machine_kexec_prepare+0xe5/0x6c0
? kimage_free_page_list+0x52/0x70
sys_kexec_load+0x141/0x600
? vfs_write+0x100/0x180
system_call_fastpath+0x16/0x1b
The patch changes sanity_check_segment_list() to verify that the usage by
all segments does not exceed half of memory.
[akpm@linux-foundation.org: fix for kexec-return-error-number-directly.patch, update comment]
Link: http://lkml.kernel.org/r/1469625474-53904-1-git-send-email-zhongjiang@huawei.com
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Suggested-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Dave Young <dyoung@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Provide a wrapper function to be used by kernel code to check whether a
crash kernel is loaded. It returns the same value that can be seen in
/sys/kernel/kexec_crash_loaded by userspace programs.
I'm exporting the function, because it will be used by Xen, and it is
possible to compile Xen modules separately to enable the use of PV
drivers with unmodified bare-metal kernels.
Link: http://lkml.kernel.org/r/20160713121955.14969.69080.stgit@hananiah.suse.cz
Signed-off-by: Petr Tesarik <ptesarik@suse.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
crash_kexec_post_notifiers ia a boot option which controls whether the
1st kernel calls panic notifiers or not before booting the 2nd kernel.
However, there is no need to limit it to being modifiable only at boot
time. So, use core_param instead of early_param.
Link: http://lkml.kernel.org/r/20160705113327.5864.43139.stgit@softrs
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
kexec physical addresses are the boot-time view of the system. For
certain ARM systems (such as Keystone 2), the boot view of the system
does not match the kernel's view of the system: the boot view uses a
special alias in the lower 4GB of the physical address space.
To cater for these kinds of setups, we need to translate between the
boot view physical addresses and the normal kernel view physical
addresses. This patch extracts the current transation points into
linux/kexec.h, and allows an architecture to override the functions.
Due to the translations required, we unfortunately end up with six
translation functions, which are reduced down to four that the
architecture can override.
[akpm@linux-foundation.org: kexec.h needs asm/io.h for phys_to_virt()]
Link: http://lkml.kernel.org/r/E1b8koP-0004HZ-Vf@rmk-PC.armlinux.org.uk
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Pratyush Anand <panand@redhat.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On PAE systems (eg, ARM LPAE) the vmcore note may be located above 4GB
physical on 32-bit architectures, so we need a wider type than "unsigned
long" here. Arrange for paddr_vmcoreinfo_note() to return a
phys_addr_t, thereby allowing it to be located above 4GB.
This makes no difference for kexec-tools, as they already assume a
64-bit type when reading from this file.
Link: http://lkml.kernel.org/r/E1b8koK-0004HS-K9@rmk-PC.armlinux.org.uk
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Pratyush Anand <panand@redhat.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
