| Age | Commit message (Collapse) | Author |
|---|
|
It can be useful to lower max_gso_segs on NIC with very low
number of TX descriptors like bcmgenet.
However, this is defeated by bridge since it does not propagate
the lower value of max_gso_segs and max_gso_size.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Petri Gynther <pgynther@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On bridge needed_headroom changes, the enslaved devices are
notified via the ndo_set_rx_headroom method
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Disallow adding interfaces to a bridge when vlan filtering operation
failed. Send the failure code to the user.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sometimes the drivers and other code would find it handy to know some
internal information about upper device being changed. So allow upper-code
to pass information down to notifier listeners during linking.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eliminate netdev_master_upper_dev_link_private and pass priv directly as
a parameter of netdev_master_upper_dev_link.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since spinlock is held here, defer the switchdev operation. Also, ensure
that defered switchdev ops are processed before port master device
is unlinked.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ido Schimmel reported a problem with switchdev devices because of the
order change of del_nbp operations, more specifically the move of
nbp_vlan_flush() which deletes all vlans and frees vlgrp after the
rx_handler has been unregistered. So in order to fix this move
vlan_flush back where it was and make it destroy the rhtable after
NULLing vlgrp and waiting a grace period to make sure noone can see it.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a new port is being added we need to make vlgrp available after
rhashtable has been initialized and when removing a port we need to
flush the vlans and free the resources after we're sure noone can use
the port, i.e. after it's removed from the port list and synchronize_rcu
is executed.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the bridge (or port) is brought down/up flush only temp entries and
leave the perm ones. Flush perm entries only when deleting the bridge
device or the associated port.
Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new argument to br_fdb_delete_by_port which allows to specify a
vid to match when flushing entries and use it in nbp_vlan_delete() to
flush the dynamically learned entries of the vlan/port pair when removing
a vlan from a port. Before this patch only the local mac was being
removed and the dynamically learned ones were left to expire.
Note that the do_all argument is still respected and if specified, the
vid will be ignored.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On adding an interface br_add_if() sets the MTU to the min of
all the interfaces. Do the same thing on removing an interface too
in br_del_if.
Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA-enabled master network devices with a switch tagging protocol should
strip the protocol specific format before handing the frame over to
higher layer.
When adding such a DSA master network device as a bridge member, we go
through the following code path when receiving a frame:
__netif_receive_skb_core
-> first ptype check against ptype_all is not returning any
handler for this skb
-> check and invoke rx_handler:
-> deliver frame to the bridge layer: br_handle_frame
DSA registers a ptype handler with the fake ETH_XDSA ethertype, which is
called *after* the bridge-layer rx_handler has run. br_handle_frame()
tries to parse the frame it received from the DSA master network device,
and will not be able to match any of its conditions and jumps straight
at the end of the end of br_handle_frame() and returns
RX_HANDLER_CONSUMED there.
Since we returned RX_HANDLER_CONSUMED, __netif_receive_skb_core() stops
RX processing for this frame and returns NET_RX_SUCCESS, so we never get
a chance to call our switch tag packet processing logic and deliver
frames to the DSA slave network devices, and so we do not get any
functional bridge members at all.
Instead of cluttering the bridge receive path with DSA-specific checks,
and rely on assumptions about how __netif_receive_skb_core() is
processing frames, we simply deny adding the DSA master network device
(conduit interface) as a bridge member, leaving only the slave DSA
network devices to be bridge members, since those will work correctly in
all circumstances.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently a bridge device turns off TSO feature if no bridge ports
support it. We can always enable it, since packets can be segmented on
ports by software as well as on the bridge device.
This will reduce the number of packets processed in the bridge.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when vlan filtering is turned on on the bridge, the bridge
will drop all traffic untill the user configures the filter. This
isn't very nice for ports that don't care about vlans and just
want untagged traffic.
A concept of a default_pvid was recently introduced. This patch
adds filtering support for default_pvid. Now, ports that don't
care about vlans and don't define there own filter will belong
to the VLAN of the default_pvid and continue to receive untagged
traffic.
This filtering can be disabled by setting default_pvid to 0.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for being able to propagate port states to e.g: notifiers
or other kernel parts, do not manipulate the port state directly, but
instead use a helper function which will allow us to do a bit more than
just setting the state.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The thing is that netdev_master_upper_dev_link calls
call_netdevice_notifiers(NETDEV_CHANGEUPPER, dev). That generates rtnl
link message and during that, rtnl_link_ops->fill_slave_info is called.
But with current ordering, rx_handler and IFF_BRIDGE_PORT are not set
yet so there would have to be check for that in fill_slave_info callback.
Resolve this by reordering to similar what bonding and team does to
avoid the check.
Also add removal of IFF_BRIDGE_PORT flag into error path.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend alloc_netdev{,_mq{,s}}() to take name_assign_type as argument, and convert
all users to pass NET_NAME_UNKNOWN.
Coccinelle patch:
@@
expression sizeof_priv, name, setup, txqs, rxqs, count;
@@
(
-alloc_netdev_mqs(sizeof_priv, name, setup, txqs, rxqs)
+alloc_netdev_mqs(sizeof_priv, name, NET_NAME_UNKNOWN, setup, txqs, rxqs)
|
-alloc_netdev_mq(sizeof_priv, name, setup, count)
+alloc_netdev_mq(sizeof_priv, name, NET_NAME_UNKNOWN, setup, count)
|
-alloc_netdev(sizeof_priv, name, setup)
+alloc_netdev(sizeof_priv, name, NET_NAME_UNKNOWN, setup)
)
v9: move comments here from the wrong commit
Signed-off-by: Tom Gundersen <teg@jklm.no>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
br_manage_promisc() incorrectly expects br_auto_port() to return only 0
or 1, while it actually returns flags, i.e., a subset of BR_AUTO_MASK.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As commit 2796d0c648c94 ("bridge: Automatically manage port
promiscuous mode."), make the add_if use dev_set_allmulti
instead of dev_set_promiscuous, so when add_if failed, we
should do dev_set_allmulti(dev, -1).
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Reviewed-by: Amos Kong <akong@redhat.com>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There exist configurations where the administrator or another management
entity has the foreknowledge of all the mac addresses of end systems
that are being bridged together.
In these environments, the administrator can statically configure known
addresses in the bridge FDB and disable flooding and learning on ports.
This makes it possible to turn off promiscuous mode on the interfaces
connected to the bridge.
Here is why disabling flooding and learning allows us to control
promiscuity:
Consider port X. All traffic coming into this port from outside the
bridge (ingress) will be either forwarded through other ports of the
bridge (egress) or dropped. Forwarding (egress) is defined by FDB
entries and by flooding in the event that no FDB entry exists.
In the event that flooding is disabled, only FDB entries define
the egress. Once learning is disabled, only static FDB entries
provided by a management entity define the egress. If we provide
information from these static FDBs to the ingress port X, then we'll
be able to accept all traffic that can be successfully forwarded and
drop all the other traffic sooner without spending CPU cycles to
process it.
Another way to define the above is as following equations:
ingress = egress + drop
expanding egress
ingress = static FDB + learned FDB + flooding + drop
disabling flooding and learning we a left with
ingress = static FDB + drop
By adding addresses from the static FDB entries to the MAC address
filter of an ingress port X, we fully define what the bridge can
process without dropping and can thus turn off promiscuous mode,
thus dropping packets sooner.
There have been suggestions that we may want to allow learning
and update the filters with learned addresses as well. This
would require mac-level authentication similar to 802.1x to
prevent attacks against the hw filters as they are limited
resource.
Additionally, if the user places the bridge device in promiscuous mode,
all ports are placed in promiscuous mode regardless of the changes
to flooding and learning.
Since the above functionality depends on full static configuration,
we have also require that vlan filtering be enabled to take
advantage of this. The reason is that the bridge has to be
able to receive and process VLAN-tagged frames and the there
are only 2 ways to accomplish this right now: promiscuous mode
or vlan filtering.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a BR_PROMISC per-port flag that will help us track if the
current port is supposed to be in promiscuous mode or not. For now,
always start in promiscuous mode.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By default, ports on the bridge are capable of automatic
discovery of nodes located behind the port. This is accomplished
via flooding of unknown traffic (BR_FLOOD) and learning the
mac addresses from these packets (BR_LEARNING).
If the above functionality is disabled by turning off these
flags, the port requires static configuration in the form
of static FDB entries to function properly.
This patch adds functionality to keep track of all ports
capable of automatic discovery. This will later be used
to control promiscuity settings.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The gfp parameter was added in:
commit 47be03a28cc6c80e3aa2b3e8ed6d960ff0c5c0af
Author: Amerigo Wang <amwang@redhat.com>
Date: Fri Aug 10 01:24:37 2012 +0000
netpoll: use GFP_ATOMIC in slave_enable_netpoll() and __netpoll_setup()
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason for the gfp parameter was removed in:
commit c4cdef9b7183159c23c7302aaf270d64c549f557
Author: dingtianhong <dingtianhong@huawei.com>
Date: Tue Jul 23 15:25:27 2013 +0800
bonding: don't call slave_xxx_netpoll under spinlocks
The slave_xxx_netpoll will call synchronize_rcu_bh(),
so the function may schedule and sleep, it should't be
called under spinlocks.
bond_netpoll_setup() and bond_netpoll_cleanup() are always
protected by rtnl lock, it is no need to take the read lock,
as the slave list couldn't be changed outside rtnl lock.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing else that calls __netpoll_setup or ndo_netpoll_setup
requires a gfp paramter, so remove the gfp parameter from both
of these functions making the code clearer.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vlan code may need fdb change when changing mac address of bridge device
even if it is caused by the mac address changing of a bridge port.
Example configuration:
ip link set eth0 address 12:34:56:78:90:ab
ip link set eth1 address aa:bb:cc:dd:ee:ff
brctl addif br0 eth0
brctl addif br0 eth1 # br0 will have mac address 12:34:56:78:90:ab
bridge vlan add dev br0 vid 10 self
bridge vlan add dev eth0 vid 10
We will have fdb entry such that f->dst == NULL, f->vlan_id == 10 and
f->addr == 12:34:56:78:90:ab at this time.
Next, change the mac address of eth0 to greater value.
ip link set eth0 address ee:ff:12:34:56:78
Then, mac address of br0 will be recalculated and set to aa:bb:cc:dd:ee:ff.
However, an entry aa:bb:cc:dd:ee:ff will not be created and we will be not
able to communicate using br0 on vlan 10.
Address this issue by deleting and adding local entries whenever
changing the mac address of the bridge device.
If there already exists an entry that has the same address, for example,
in case that br_fdb_changeaddr() has already inserted it,
br_fdb_change_mac_address() will simply fail to insert it and no
duplicated entry will be made, as it was.
This approach also needs br_add_if() to call br_fdb_insert() before
br_stp_recalculate_bridge_id() so that we don't create an entry whose
dst == NULL in this function to preserve previous behavior.
Note that this is a slight change in behavior where the bridge device can
receive the traffic to the new address before calling
br_stp_recalculate_bridge_id() in br_add_if().
However, it is not a problem because we have already the address on the
new port and such a way to insert new one before recalculating bridge id
is taken in br_device_event() as well.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
And it can become static.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix spelling errors in bridge driver.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bridge dev
When the following commands are executed:
brctl addbr br0
ifconfig br0 hw ether <addr>
rmmod bridge
The calltrace will occur:
[ 563.312114] device eth1 left promiscuous mode
[ 563.312188] br0: port 1(eth1) entered disabled state
[ 563.468190] kmem_cache_destroy bridge_fdb_cache: Slab cache still has objects
[ 563.468197] CPU: 6 PID: 6982 Comm: rmmod Tainted: G O 3.12.0-0.7-default+ #9
[ 563.468199] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 563.468200] 0000000000000880 ffff88010f111e98 ffffffff814d1c92 ffff88010f111eb8
[ 563.468204] ffffffff81148efd ffff88010f111eb8 0000000000000000 ffff88010f111ec8
[ 563.468206] ffffffffa062a270 ffff88010f111ed8 ffffffffa063ac76 ffff88010f111f78
[ 563.468209] Call Trace:
[ 563.468218] [<ffffffff814d1c92>] dump_stack+0x6a/0x78
[ 563.468234] [<ffffffff81148efd>] kmem_cache_destroy+0xfd/0x100
[ 563.468242] [<ffffffffa062a270>] br_fdb_fini+0x10/0x20 [bridge]
[ 563.468247] [<ffffffffa063ac76>] br_deinit+0x4e/0x50 [bridge]
[ 563.468254] [<ffffffff810c7dc9>] SyS_delete_module+0x199/0x2b0
[ 563.468259] [<ffffffff814e0922>] system_call_fastpath+0x16/0x1b
[ 570.377958] Bridge firewalling registered
--------------------------- cut here -------------------------------
The reason is that when the bridge dev's address is changed, the
br_fdb_change_mac_address() will add new address in fdb, but when
the bridge was removed, the address entry in the fdb did not free,
the bridge_fdb_cache still has objects when destroy the cache, Fix
this by flushing the bridge address entry when removing the bridge.
v2: according to the Toshiaki Makita and Vlad's suggestion, I only
delete the vlan0 entry, it still have a leak here if the vlan id
is other number, so I need to call fdb_delete_by_port(br, NULL, 1)
to flush all entries whose dst is NULL for the bridge.
Suggested-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently don't call br_vlan_flush() when deleting a bridge, which
leads to memory leak if br->vlan_info is allocated.
Steps to reproduce:
while :
do
brctl addbr br0
bridge vlan add dev br0 vid 10 self
brctl delbr br0
done
We can observe the cache size of corresponding slab entry
(as kmalloc-2048 in SLUB) is increased.
kmemleak output:
unreferenced object 0xffff8800b68a7000 (size 2048):
comm "bridge", pid 2086, jiffies 4295774704 (age 47.656s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 48 9b 36 00 88 ff ff .........H.6....
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff815eb6ae>] kmemleak_alloc+0x4e/0xb0
[<ffffffff8116a1ca>] kmem_cache_alloc_trace+0xca/0x220
[<ffffffffa03eddd6>] br_vlan_add+0x66/0xe0 [bridge]
[<ffffffffa03e543c>] br_setlink+0x2dc/0x340 [bridge]
[<ffffffff8150e481>] rtnl_bridge_setlink+0x101/0x200
[<ffffffff8150d9d9>] rtnetlink_rcv_msg+0x99/0x260
[<ffffffff81528679>] netlink_rcv_skb+0xa9/0xc0
[<ffffffff8150d938>] rtnetlink_rcv+0x28/0x30
[<ffffffff81527ccd>] netlink_unicast+0xdd/0x190
[<ffffffff8152807f>] netlink_sendmsg+0x2ff/0x740
[<ffffffff814e8368>] sock_sendmsg+0x88/0xc0
[<ffffffff814e8ac8>] ___sys_sendmsg.part.14+0x298/0x2b0
[<ffffffff814e91de>] __sys_sendmsg+0x4e/0x90
[<ffffffff814e922e>] SyS_sendmsg+0xe/0x10
[<ffffffff81601669>] system_call_fastpath+0x16/0x1b
[<ffffffffffffffff>] 0xffffffffffffffff
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some slave devices may have set a dev->needed_headroom value which is
different than the default one, most likely in order to prepend a
hardware descriptor in front of the Ethernet frame to send. Whenever a
new slave is added to a bridge, ensure that we update the
needed_headroom value accordingly to account for the slave
needed_headroom value.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This started out with fixing a sparse warning, then I realized that
the wrapper function br_netpoll_info could just be collapsed away
by rolling it into the enable code.
Also, eliminate unnecessary goto's
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a flag to control flood of unicast traffic. By default, flood is
on and the bridge will flood unicast traffic if it doesn't know
the destination. When the flag is turned off, unicast traffic
without an FDB will not be forwarded to the specified port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow user to control whether mac learning is enabled on the port.
By default, mac learning is enabled. Disabling mac learning will
cause new dynamic FDB entries to not be created for a particular port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Keep a STP port path cost value if it was set by a user.
Don't replace it with the link-speed based path cost
whenever the link goes down and comes back up.
Reported-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 00cfec37484761 (net: add a synchronize_net() in
netdev_rx_handler_unregister())
allows us to remove the synchronized_net() call from del_nbp()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When VLAN is added to the port, a local fdb entry for that port
(the entry with the mac address of the port) is added for that
VLAN. This way we can correctly determine if the traffic
is for the bridge itself. If the address of the port changes,
we try to change all the local fdb entries we have for that port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a netlink interface to add and remove vlan configuration on bridge port.
The interface uses the RTM_SETLINK message and encodes the vlan
configuration inside the IFLA_AF_SPEC. It is possble to include multiple
vlans to either add or remove in a single message.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds an optional infrustructure component to bridge that would allow
native vlan filtering in the bridge. Each bridge port (as well
as the bridge device) now get a VLAN bitmap. Each bit in the bitmap
is associated with a vlan id. This way if the bit corresponding to
the vid is set in the bitmap that the packet with vid is allowed to
enter and exit the port.
Write access the bitmap is protected by RTNL and read access
protected by RCU.
Vlan functionality is disabled by default.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bridge link detection should follow the operational state
of the lower device, rather than the carrier bit. This allows devices
like tunnels that are controlled by userspace control plane to work
with bridge STP link management.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When netdev_set_master faild in br_add_if, we should
call br_netpoll_disable to do some cleanup jobs,such
as free the memory of struct netpoll which allocated
in br_netpoll_enable.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add comments on why we don't notify NETDEV_RELEASE.
Cc: David Miller <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This ensures that bridges created with brctl(8) or ioctl(2) directly
also carry IFLA_LINKINFO when dumped over netlink. This also allows
to create a bridge with ioctl(2) and delete it with RTM_DELLINK.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Need to cleanup bridge device timers and ports when being bridge
device is being removed via netlink.
This fixes the problem of observed when doing:
ip link add br0 type bridge
ip link set dev eth1 master br0
ip link set br0 up
ip link del br0
which would cause br0 to hang in unregister_netdev because
of leftover reference count.
Reported-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When port is added to a bridge, the old code would send the new neighbor
netlink message before the subsequent new link message. This bug makes
it difficult to use the monitoring API in an application.
This code changes the ordering to add the forwarding entry
after the port is setup. One of the error checks (for invalid address)
is moved earlier in the process to avoid having to do unwind.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
