Age | Commit message (Collapse) | Author |
|
|
|
During strong signal fluctuations under high throughput, few consecutive
failed A-MPDU transmissions can easily trigger packet loss notification,
and thus (in AP mode) client disconnection.
Reduce the number of false positives by checking the A-MPDU status flag
and treating a failed A-MPDU as a single packet.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When using RTS/CTS, the CTS-to-Self bit in radiotap TX flags is
getting set instead of the RTS bit. Set the correct one.
Reported-by: Larry Maxwell <larrymaxwell@agilemesh.com>
Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Rate controller in firmware may also return the Tx Rate
used for management frame that is usually sent as lowest
Tx Rate (1Mbps in 2.4GHz). So update the last_tx_rate only
if it is data frame.
This patch is tested with ath9k_htc.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Compiling with W=1 found a few variables that are set
but not used (-Wunused-but-set-variable), remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Measure TX latency and jitter statistics per station per TID.
These Measurements are disabled by default and can be enabled
via debugfs.
Features included for each station's TID:
1. Keep count of the maximum and average latency of Tx frames.
2. Keep track of many frames arrived in a specific time range
(need to enable through debugfs and configure the bins ranges)
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Conflicts:
net/wireless/reg.c
|
|
When the driver requests to move to STATIC or DYNAMIC SMPS,
we send an action frame to each associated station and
reconfigure the channel context / driver.
Of course, non-MIMO stations are ignored.
The beacon isn't updated. The association response will
include the original capabilities. Stations that associate
while in non-OFF SMPS mode will get an action frame right
after association to inform them about our current state.
Note that we wait until the end of the EAPOL. Sending an
action frame before the EAPOL is finished can be an issue
for a few clients. Clients aren't likely to send EAPOL
frames in MIMO anyway.
When the SMPS configuration gets more permissive (e.g.
STATIC -> OFF), we don't wake up stations that are asleep
We remember that they don't know about the change and send
the action frame when they wake up.
When the SMPS configuration gets more restrictive (e.g.
OFF -> STATIC), we set the TIM bit for every sleeping STA.
uAPSD stations might send MIMO until they poll the action
frame, but this is for a short period of time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix vht streams loop, initialisation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When clients are idle for too long, hostapd sends nullfunc frames for
probing. When those are acked by the client, the idle time needs to be
updated.
To make this work (and to avoid unnecessary probing), update sta->last_rx
whenever an ACK was received for a tx packet. Only do this if the flag
IEEE80211_HW_REPORTS_TX_ACK_STATUS is set.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The radiotap VHT info is 12 bytes (required to be aligned on 2) :
u16 known - IEEE80211_RADIOTAP_VHT_KNOWN_*
u8 flags - IEEE80211_RADIOTAP_VHT_FLAG_*
u8 bandwidth
u8 mcs_nss[4]
u8 coding
u8 group_id
u16 partial_aid
ATM mac80211 can handle IEEE80211_RADIOTAP_VHT_KNOWN_{GI,BANDWIDTH} and
mcs_nss[0] (i.e single user) in simple cases.
This is more a placeholder to let sniffers give more clues for VHT,
since we don't have yet the proper infrastructure/conventions
in mac80211 for complete feedback (e.g consider dynamic BW).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Change mac80211 LED trigger code to use the generic
led_trigger_blink_oneshot() API for transmit and receive activity
indication.
This gives a better feedback to the user, as with the new API each
activity event results in a visible blink, while a constant traffic
results in a continuous blink at constant rate.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
[fix LED disabled build error]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The various components accessing the bitrates table must use consider
the used channel bandwidth to select only available rates or calculate
the bitrate correctly.
There are some rates in reduced bandwidth modes which can't be
represented as multiples of 500kbps, like 2.25 MBit/s in 5 MHz mode. The
standard suggests to round up to the next multiple of 500kbps, just do
that in mac80211 as well.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[make rate unsigned in ieee80211_add_tx_radiotap_header(), squash fix]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
|
|
Add routines to
- maintain a PS mode for each peer and a non-peer PS mode
- indicate own PS mode in transmitted frames
- track neighbor STAs power modes
- buffer frames when neighbors are in PS mode
- add TIM and Awake Window IE to beacons
- release frames in Mesh Peer Service Periods
Add local_pm to sta_info to represent the link-specific power
mode at this station towards the remote station. When a peer
link is established, use the default power mode stored in mesh
config. Update the PS status if the peering status of a neighbor
changes.
Maintain a mesh power mode for non-peer mesh STAs. Set the
non-peer power mode to active mode during peering. Authenticated
mesh peering is currently not working when either node is
configured to be in power save mode.
Indicate the current power mode in transmitted frames. Use QoS
Nulls to indicate mesh power mode transitions.
For performance reasons, calls to the function setting the frame
flags are placed in HWMP routing routines, as there the STA
pointer is already available.
Add peer_pm to sta_info to represent the peer's link-specific
power mode towards the local station. Add nonpeer_pm to
represent the peer's power mode towards all non-peer stations.
Track power modes based on received frames.
Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS
neighbor counter and group-addressed frame buffer).
Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame
buffering routines in the tx path. Update num_sta_ps to buffer
and release group-addressed frames after DTIM beacons.
Announce the awake window duration in beacons if in light or
deep sleep mode towards any peer or non-peer. Create a TIM IE
similarly to AP mode and add it to mesh beacons. Parse received
Awake Window IEs and check TIM IEs for buffered frames.
Release frames towards peers in mesh Peer Service Periods. Use
the corresponding trigger frames and monitor the MPSP status.
Append a QoS Null as trigger frame if neccessary to properly end
the MPSP. Currently, in HT channels MPSPs behave imperfectly and
show large delay spikes and frame losses.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When sending authentication/association frames they
might take a bit of time to go out because we may
have to synchronise with the AP, in particular in
the case where it's really a P2P GO. In this case
the 200ms fixed timeout could potentially be too
short if the beacon interval is relatively large.
For drivers that report TX status we can do better.
Instead of starting the timeout directly, start it
only when the frame status arrives. Since then the
frame was out on the air, we can wait shorter (the
typical response time is supposed to be 30ms, wait
100ms.) Also, if the frame failed to be transmitted
try again right away instead of waiting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is basically a revert of:
commit 5b632fe85ec82e5c43740b52e74c66df50a37db3
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Mon Dec 3 12:56:33 2012 +0100
mac80211: introduce IEEE80211_HW_TEARDOWN_AGGR_ON_BAR_FAIL
We do not need this flag any longer, rt2x00 BAR/BA problem was fixed
correctly by wireless-testing commit:
commit 84e9e8ebd369679a958200a8baca96aafb2393bb
Author: Helmut Schaa <helmut.schaa@googlemail.com>
Date: Thu Jan 17 17:34:32 2013 +0100
rt2x00: Improve TX status handling for BlockAckReq frames
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Conflicts:
drivers/net/wireless/mwifiex/sta_ioctl.c
net/mac80211/scan.c
|
|
Commit f0425beda4d404a6e751439b562100b902ba9c98 "mac80211: retry sending
failed BAR frames later instead of tearing down aggr" caused regression
on rt2x00 hardware (connection hangs). This regression was fixed by
commit be03d4a45c09ee5100d3aaaedd087f19bc20d01 "rt2x00: Don't let
mac80211 send a BAR when an AMPDU subframe fails". But the latter
commit caused yet another problem reported in
https://bugzilla.kernel.org/show_bug.cgi?id=42828#c22
After long discussion in this thread:
http://mid.gmane.org/20121018075615.GA18212@redhat.com
and testing various alternative solutions, which failed on one or other
setup, we have no other good fix for the issues like just revert both
mentioned earlier commits.
To do not affect other hardware which benefit from commit
f0425beda4d404a6e751439b562100b902ba9c98, instead of reverting it,
introduce flag that when used will restore mac80211 behaviour before
the commit.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
[replaced link with mid.gmane.org that has message-id]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a debugfs file showing the signal strength
of the ack frame that is received for the
currently sent tx packet
Signed-off-by: Saravana <saravanad@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c
drivers/net/wireless/iwlwifi/pcie/tx.c
|
|
Fixes more wifi status skb leaks, leading to hostapd/wpa_supplicant hangs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The TX status reporting is done for both the
nl80211 report as well as the socket option.
The socket option is also reported when an
skb is dropped to guarantee that the copy in
the IDR tree is freed and status is reported
to userspace.
However, when a frame is dropped, no nl80211
status is reported. This can cause userspace
to stop making progress while waiting for a
status notification.
Combine the nl80211 and socket option status
reporting into a new function and call it in
both places -- when the status comes in from
the driver and when the skb is dropped.
While at it, also simplify the code in the
nl80211 portion a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).
Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
A few places free skbs using dev_kfree_skb even though they're called
after ieee80211_subif_start_xmit might have cloned it for tracking tx
status. Use ieee80211_free_txskb here to prevent skb leaks.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
skb->dev might contain a stale reference to a device that was already
deleted, and using it unchecked can lead to invalid pointer accesses.
Since this is only used for nl80211 tx, iterate over active interfaces
to find a match for skb->dev, and discard the tx status if the device
is gone.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
After cfg80211 got a P2P Device abstraction, add
support to mac80211. Whether it really is supported
or not will depend on whether or not the driver has
support for it, but mac80211 needs to change to be
able to support drivers that need a P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The management frame and remain-on-channel APIs will be
needed in the P2P device abstraction, so move them over
to the new wdev-based APIs. Userspace can still use both
the interface index and wdev identifier for them so it's
backward compatible, but for the P2P Device wdev it will
be able to use the wdev identifier only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
* a lot of messages should be pr_info, not pr_debug
* wholesale use of pr_debug makes it require *both*
Kconfig and dynamic configuration
* there are still a lot of ifdefs
* the style is very inconsistent, sometimes the
sdata->name is printed in front
Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Two instances of CONFIG_MAC80211_VERBOSE_DEBUG
should be different, fix them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Redesign all the off-channel code, getting rid of
the generic off-channel work concept, replacing
it with a simple remain-on-channel list.
This fixes a number of small issues with the ROC
implementation:
* offloaded remain-on-channel couldn't be queued,
now we can queue it as well, if needed
* in iwlwifi (the only user) offloaded ROC is
mutually exclusive with scanning, use the new
queue to handle that case -- I expect that it
will later depend on a HW flag
The bigger issue though is that there's a bad bug
in the current implementation: if we get a mgmt
TX request while HW roc is active, and this new
request has a wait time, we actually schedule a
software ROC instead since we can't guarantee the
existing offloaded ROC will still be that long.
To fix this, the queuing mechanism was needed.
The queuing mechanism for offloaded ROC isn't yet
optimal, ideally we should add API to have the HW
extend the ROC if needed. We could add that later
but for now use a software implementation.
Overall, this unifies the behaviour between the
offloaded and software-implemented case as much
as possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Standardize the debugging to be able to use dynamic_debug.
Coalesce formats, align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I noticed a possible issue in the status count field management of the
ieee80211_tx_info data structure. In particular, when the AGGR
processing is employed,
status.rates[].count is set just for the first frame and not for
others belonging to the same burst, leading to wrong statistic data in
the mac80211 debug file system.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Because of the constant size and guaranteed 16 bit alignment, the inline
compare_ether_addr function is much cheaper than calling memcmp.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some files implicitly get this via mesh.h
which itself doesn't need it, so move the
inclusion into the right files. Some other
files don't need it at all but include it,
so remove it from there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It seems that -Wshadow is no longer default in
sparse runs, but let's fix the warnings anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use ieee80211_is_data, ieee80211_is_mgmt and ieee80211_is_first_frag
in the tx status path. This makes the code easier to read and allows us
to remove two local variables: frag and type.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
drivers/net/wireless/iwlwifi/iwl-agn.c
drivers/net/wireless/libertas/cfg.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux
Conflicts:
drivers/net/wireless/iwlegacy/iwl-debugfs.c
drivers/net/wireless/iwlegacy/iwl-rx.c
drivers/net/wireless/iwlegacy/iwl-scan.c
drivers/net/wireless/iwlegacy/iwl-tx.c
include/net/bluetooth/bluetooth.h
|
|
I intoduced this bug in commit a2fe81667410723d941a688e1958a49d67ca3346
"mac80211: Build TX radiotap header dynamically"
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Implement the socket wifi TX status error
queue reflection in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Support probing clients with null data frames
in AP mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Drivers that need to drop a frame before it
can be transmitted will usually simply free
that frame. This is currently fine, but in
the future it'll be needed to tell mac80211
about this case, so add a new routine that
frees a TX skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
mac80211 already filled in the MCS rate info for rx'ed frames but tx'ed
frames that are sent to a monitor interface during the status callback
lack this information.
Add the radiotap fields for MCS info to ieee80211_tx_status_rtap_hdr
and populate them when sending tx'ed frames to the monitors.
The needed headroom is only extended by one byte since we don't include
legacy rate information in the rtap header for HT frames.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Get rid of the ieee80211_tx_status_rtap_hdr struct and instead build the
rtap header dynamically. This makes it easier to extend the rtap header
generation in the future.
Add ieee80211_tx_radiotap_len to calculate the expected size of the
rtap header before generating it. Since we can't check if the rtap
header fits into the requested headroom during compile time anymore
add a WARN_ON_ONCE.
Also move the actual rtap header generation into its own function.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When I introduced in-kernel off-channel TX I
introduced a bug -- the work can't be canceled
again because the code clear the skb pointer.
Fix this by keeping track separately of whether
TX status has already been reported.
Cc: stable@kernel.org [2.6.38+]
Reported-by: Jouni Malinen <j@w1.fi>
Tested-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.
The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.
On x86-64, this is a fairly significant code
size reduction:
text data bss dec hex
427861 23648 1008 452517 6e7a5 before
425383 23648 976 450007 6ddd7 after
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add uAPSD support to mac80211. This is probably not
possible with all devices, so advertising it with
the cfg80211 flag will be left up to drivers that
want it.
Due to my previous patches it is now a fairly
straight-forward extension. Drivers need to have
accurate TX status reporting for the EOSP frame.
For drivers that buffer themselves, the provided
APIs allow releasing the right number of frames,
but then drivers need to set EOSP and more-data
themselves. This is documented in more detail in
the new code itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It doesn't seem likely, but maybe possible, that the
more-data bit needs to be recomputed due to changes
in the queued frames. Clear it for filtered frames
to ensure that we never send it incorrectly. It'll
be set again as necessary when we retransmit this
frame.
The more likely case is maybe where the station woke
up after the filtered frame in which case more-data
should be clear when the frame is transmitted to the
station since it is now awake.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|