| Age | Commit message (Collapse) | Author |
|---|
|
minimal configurations where EPOLL, PERF_EVENTS, etc are disabled,
but NET is enabled, are failing to build with link error:
kernel/built-in.o: In function `bpf_prog_load':
syscall.c:(.text+0x3b728): undefined reference to `anon_inode_getfd'
fix it by selecting ANON_INODES when NET is enabled
Reported-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net-next
This batch contains two fixes for what you have in your net-next,
they are:
1) Remove nf_send_reset6() from header file. This function now resides
in the nf_reject_ipv6 module. Reported by Eric Dumazet.
2) Fix wrong NFT_REJECT_ICMPX_MAX definition and adjust code to fix
errors reported by Dan Carpenter's static analysis tools.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
pull request: wireless-next 2014-10-09
Please pull this batch of fixes intended for the 3.18 stream!
Andrea Merello makes rtl818x_pci use a more reasonable transmission
rate for HW generated frames.
Fabian Frederick tweaks some kernel-doc bits to avoid warnings.
Larry Finger corrects a possible unaligned access in the rtlwifi code.
Marek Puzyniak avoids a kernel panic in ath9k_hw_reset.
Sujith Manoharan goes for the hat trick -- he fixes a smatch warning
in the shared ath code, he fixes a crash in ath9k, and he corrects
a sequence number assignment problem in ath9k too.
For ease of merging, I pulled the last bits of the wireless tree as well...
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Restore the quota fairness between qdisc's, that we broke with commit
5772e9a346 ("qdisc: bulk dequeue support for qdiscs with TCQ_F_ONETXQUEUE").
Before that commit, the quota in __qdisc_run() were in packets as
dequeue_skb() would only dequeue a single packet, that assumption
broke with bulk dequeue.
We choose not to account for the number of packets inside the TSO/GSO
packets (accessable via "skb_gso_segs"). As the previous fairness
also had this "defect". Thus, GSO/TSO packets counts as a single
packet.
Further more, we choose to slack on accuracy, by allowing a bulk
dequeue try_bulk_dequeue_skb() to exceed the "packets" limit, only
limited by the BQL bytelimit. This is done because BQL prefers to get
its full budget for appropriate feedback from TX completion.
In future, we might consider reworking this further and, if it allows,
switch to a time-based model, as suggested by Eric. Right now, we only
restore old semantics.
Joint work with Eric, Hannes, Daniel and Jesper. Hannes wrote the
first patch in cooperation with Daniel and Jesper. Eric rewrote the
patch.
Fixes: 5772e9a346 ("qdisc: bulk dequeue support for qdiscs with TCQ_F_ONETXQUEUE")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fix following warning.
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'header_len'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'data_len'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'max_page_order'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'errcode'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'gfp_mask'
Acutually the descriptions exist, but missing "@" in front.
This problem start to happen when following commit was merged
into Linus's tree during 3.18-rc1 merge period.
commit 2e4e44107176d552f8bb1bb76053e850e3809841
net: add alloc_skb_with_frags() helper
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
no secid argument in netlbl_cfg_unlbl_static_del
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
"Most notable changes in here:
1) By far the biggest accomplishment, thanks to a large range of
contributors, is the addition of multi-send for transmit. This is
the result of discussions back in Chicago, and the hard work of
several individuals.
Now, when the ->ndo_start_xmit() method of a driver sees
skb->xmit_more as true, it can choose to defer the doorbell
telling the driver to start processing the new TX queue entires.
skb->xmit_more means that the generic networking is guaranteed to
call the driver immediately with another SKB to send.
There is logic added to the qdisc layer to dequeue multiple
packets at a time, and the handling mis-predicted offloads in
software is now done with no locks held.
Finally, pktgen is extended to have a "burst" parameter that can
be used to test a multi-send implementation.
Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4,
virtio_net
Adding support is almost trivial, so export more drivers to
support this optimization soon.
I want to thank, in no particular or implied order, Jesper
Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal
Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann,
David Tat, Hannes Frederic Sowa, and Rusty Russell.
2) PTP and timestamping support in bnx2x, from Michal Kalderon.
3) Allow adjusting the rx_copybreak threshold for a driver via
ethtool, and add rx_copybreak support to enic driver. From
Govindarajulu Varadarajan.
4) Significant enhancements to the generic PHY layer and the bcm7xxx
driver in particular (EEE support, auto power down, etc.) from
Florian Fainelli.
5) Allow raw buffers to be used for flow dissection, allowing drivers
to determine the optimal "linear pull" size for devices that DMA
into pools of pages. The objective is to get exactly the
necessary amount of headers into the linear SKB area pre-pulled,
but no more. The new interface drivers use is eth_get_headlen().
From WANG Cong, with driver conversions (several had their own
by-hand duplicated implementations) by Alexander Duyck and Eric
Dumazet.
6) Support checksumming more smoothly and efficiently for
encapsulations, and add "foo over UDP" facility. From Tom
Herbert.
7) Add Broadcom SF2 switch driver to DSA layer, from Florian
Fainelli.
8) eBPF now can load programs via a system call and has an extensive
testsuite. Alexei Starovoitov and Daniel Borkmann.
9) Major overhaul of the packet scheduler to use RCU in several major
areas such as the classifiers and rate estimators. From John
Fastabend.
10) Add driver for Intel FM10000 Ethernet Switch, from Alexander
Duyck.
11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric
Dumazet.
12) Add Datacenter TCP congestion control algorithm support, From
Florian Westphal.
13) Reorganize sk_buff so that __copy_skb_header() is significantly
faster. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits)
netlabel: directly return netlbl_unlabel_genl_init()
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
net: description of dma_cookie cause make xmldocs warning
cxgb4: clean up a type issue
cxgb4: potential shift wrapping bug
i40e: skb->xmit_more support
net: fs_enet: Add NAPI TX
net: fs_enet: Remove non NAPI RX
r8169:add support for RTL8168EP
net_sched: copy exts->type in tcf_exts_change()
wimax: convert printk to pr_foo()
af_unix: remove 0 assignment on static
ipv6: Do not warn for informational ICMP messages, regardless of type.
Update Intel Ethernet Driver maintainers list
bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING
tipc: fix bug in multicast congestion handling
net: better IFF_XMIT_DST_RELEASE support
net/mlx4_en: remove NETDEV_TX_BUSY
3c59x: fix bad split of cpu_to_le32(pci_map_single())
net: bcmgenet: fix Tx ring priority programming
...
|
|
|
|
No need to store netlbl_unlabel_genl_init result and test it before returning.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to copy exts->type when committing the change, otherwise
it would be always 0. This is a quick fix for -net and -stable,
for net-next tcf_exts will be removed.
Fixes: commit 33be627159913b094bb578e83 ("net_sched: act: use standard struct list_head")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
s/state/blocked
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Pull nfsd updates from Bruce Fields:
"Highlights:
- support the NFSv4.2 SEEK operation (allowing clients to support
SEEK_HOLE/SEEK_DATA), thanks to Anna.
- end the grace period early in a number of cases, mitigating a
long-standing annoyance, thanks to Jeff
- improve SMP scalability, thanks to Trond"
* 'for-3.18' of git://linux-nfs.org/~bfields/linux: (55 commits)
nfsd: eliminate "to_delegation" define
NFSD: Implement SEEK
NFSD: Add generic v4.2 infrastructure
svcrdma: advertise the correct max payload
nfsd: introduce nfsd4_callback_ops
nfsd: split nfsd4_callback initialization and use
nfsd: introduce a generic nfsd4_cb
nfsd: remove nfsd4_callback.cb_op
nfsd: do not clear rpc_resp in nfsd4_cb_done_sequence
nfsd: fix nfsd4_cb_recall_done error handling
nfsd4: clarify how grace period ends
nfsd4: stop grace_time update at end of grace period
nfsd: skip subsequent UMH "create" operations after the first one for v4.0 clients
nfsd: set and test NFSD4_CLIENT_STABLE bit to reduce nfsdcltrack upcalls
nfsd: serialize nfsdcltrack upcalls for a particular client
nfsd: pass extra info in env vars to upcalls to allow for early grace period end
nfsd: add a v4_end_grace file to /proc/fs/nfsd
lockd: add a /proc/fs/lockd/nlm_end_grace file
nfsd: reject reclaim request when client has already sent RECLAIM_COMPLETE
nfsd: remove redundant boot_time parm from grace_done client tracking op
...
|
|
Pull NFS client updates from Trond Myklebust:
"Highlights include:
Stable fixes:
- fix an NFSv4.1 state renewal regression
- fix open/lock state recovery error handling
- fix lock recovery when CREATE_SESSION/SETCLIENTID_CONFIRM fails
- fix statd when reconnection fails
- don't wake tasks during connection abort
- don't start reboot recovery if lease check fails
- fix duplicate proc entries
Features:
- pNFS block driver fixes and clean ups from Christoph
- More code cleanups from Anna
- Improve mmap() writeback performance
- Replace use of PF_TRANS with a more generic mechanism for avoiding
deadlocks in nfs_release_page"
* tag 'nfs-for-3.18-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (66 commits)
NFSv4.1: Fix an NFSv4.1 state renewal regression
NFSv4: fix open/lock state recovery error handling
NFSv4: Fix lock recovery when CREATE_SESSION/SETCLIENTID_CONFIRM fails
NFS: Fabricate fscache server index key correctly
SUNRPC: Add missing support for RPC_CLNT_CREATE_NO_RETRANS_TIMEOUT
NFSv3: Fix missing includes of nfs3_fs.h
NFS/SUNRPC: Remove other deadlock-avoidance mechanisms in nfs_release_page()
NFS: avoid waiting at all in nfs_release_page when congested.
NFS: avoid deadlocks with loop-back mounted NFS filesystems.
MM: export page_wakeup functions
SCHED: add some "wait..on_bit...timeout()" interfaces.
NFS: don't use STABLE writes during writeback.
NFSv4: use exponential retry on NFS4ERR_DELAY for async requests.
rpc: Add -EPERM processing for xs_udp_send_request()
rpc: return sent and err from xs_sendpages()
lockd: Try to reconnect if statd has moved
SUNRPC: Don't wake tasks during connection abort
Fixing lease renewal
nfs: fix duplicate proc entries
pnfs/blocklayout: Fix a 64-bit division/remainder issue in bl_map_stripe
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull "trivial tree" updates from Jiri Kosina:
"Usual pile from trivial tree everyone is so eagerly waiting for"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
Remove MN10300_PROC_MN2WS0038
mei: fix comments
treewide: Fix typos in Kconfig
kprobes: update jprobe_example.c for do_fork() change
Documentation: change "&" to "and" in Documentation/applying-patches.txt
Documentation: remove obsolete pcmcia-cs from Changes
Documentation: update links in Changes
Documentation: Docbook: Fix generated DocBook/kernel-api.xml
score: Remove GENERIC_HAS_IOMAP
gpio: fix 'CONFIG_GPIO_IRQCHIP' comments
tty: doc: Fix grammar in serial/tty
dma-debug: modify check_for_stack output
treewide: fix errors in printk
genirq: fix reference in devm_request_threaded_irq comment
treewide: fix synchronize_rcu() in comments
checkstack.pl: port to AArch64
doc: queue-sysfs: minor fixes
init/do_mounts: better syntax description
MIPS: fix comment spelling
powerpc/simpleboot: fix comment
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine
Pull dmaengine updates from Dan Williams:
"Even though this has fixes marked for -stable, given the size and the
needed conflict resolutions this is 3.18-rc1/merge-window material.
These patches have been languishing in my tree for a long while. The
fact that I do not have the time to do proper/prompt maintenance of
this tree is a primary factor in the decision to step down as
dmaengine maintainer. That and the fact that the bulk of drivers/dma/
activity is going through Vinod these days.
The net_dma removal has not been in -next. It has developed simple
conflicts against mainline and net-next (for-3.18).
Continuing thanks to Vinod for staying on top of drivers/dma/.
Summary:
1/ Step down as dmaengine maintainer see commit 08223d80df38
"dmaengine maintainer update"
2/ Removal of net_dma, as it has been marked 'broken' since 3.13
(commit 77873803363c "net_dma: mark broken"), without reports of
performance regression.
3/ Miscellaneous fixes"
* tag 'dmaengine-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/dmaengine:
net: make tcp_cleanup_rbuf private
net_dma: revert 'copied_early'
net_dma: simple removal
dmaengine maintainer update
dmatest: prevent memory leakage on error path in thread
ioat: Use time_before_jiffies()
dmaengine: fix xor sources continuation
dma: mv_xor: Rename __mv_xor_slot_cleanup() to mv_xor_slot_cleanup()
dma: mv_xor: Remove all callers of mv_xor_slot_cleanup()
dma: mv_xor: Remove unneeded mv_xor_clean_completed_slots() call
ioat: Use pci_enable_msix_exact() instead of pci_enable_msix()
drivers: dma: Include appropriate header file in dca.c
drivers: dma: Mark functions as static in dma_v3.c
dma: mv_xor: Add DMA API error checks
ioat/dca: Use dev_is_pci() to check whether it is pci device
|
|
Use current logging functions and add module name prefix.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
static values are automatically initialized to 0
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no reason to emit a log message for these.
Based upon a suggestion from Hannes Frederic Sowa.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
|
|
As we may defragment the packet in IPv4 PRE_ROUTING and refragment
it after POST_ROUTING we should save the value of frag_max_size.
This is still very wrong as the bridge is supposed to leave the
packets intact, meaning that the right thing to do is to use the
original frag_list for fragmentation.
Unfortunately we don't currently guarantee that the frag_list is
left untouched throughout netfilter so until this changes this is
the best we can do.
There is also a spot in FORWARD where it appears that we can
forward a packet without going through fragmentation, mark it
so that we can fix it later.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One aim of commit 50100a5e39461b2a61d6040e73c384766c29975d ("tipc:
use pseudo message to wake up sockets after link congestion") was
to handle link congestion abatement in a uniform way for both unicast
and multicast transmit. However, the latter doesn't work correctly,
and has been broken since the referenced commit was applied.
If a user now sends a burst of multicast messages that is big
enough to cause broadcast link congestion, it will be put to sleep,
and not be waked up when the congestion abates as it should be.
This has two reasons. First, the flag that is used, TIPC_WAKEUP_USERS,
is set correctly, but in the wrong field. Instead of setting it in the
'action_flags' field of the arrival node struct, it is by mistake set
in the dummy node struct that is owned by the broadcast link, where it
will never tested for. Second, we cannot use the same flag for waking
up unicast and multicast users, since the function tipc_node_unlock()
needs to pick the wakeup pseudo messages to deliver from different
queues. It must hence be able to distinguish between the two cases.
This commit solves this problem by adding a new flag
TIPC_WAKEUP_BCAST_USERS, and a new function tipc_bclink_wakeup_user().
The latter is to be called by tipc_node_unlock() when the named flag,
now set in the correct field, is encountered.
v2: using explicit 'unsigned int' declaration instead of 'uint', as
per comment from David Miller.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
NFT_REJECT_ICMPX_MAX should be __NFT_REJECT_ICMPX_MAX - 1.
nft_reject_icmp_code() and nft_reject_icmpv6_code() are called from the
packet path, so BUG_ON in case we try to access an unknown abstracted
ICMP code. This should not happen since we already validate this from
nft_reject_{inet,bridge}_init().
Fixes: 51b0a5d ("netfilter: nft_reject: introduce icmp code abstraction for inet and bridge")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Testing xmit_more support with netperf and connected UDP sockets,
I found strange dst refcount false sharing.
Current handling of IFF_XMIT_DST_RELEASE is not optimal.
Dropping dst in validate_xmit_skb() is certainly too late in case
packet was queued by cpu X but dequeued by cpu Y
The logical point to take care of drop/force is in __dev_queue_xmit()
before even taking qdisc lock.
As Julian Anastasov pointed out, need for skb_dst() might come from some
packet schedulers or classifiers.
This patch adds new helper to cleanly express needs of various drivers
or qdiscs/classifiers.
Drivers that need skb_dst() in their ndo_start_xmit() should call
following helper in their setup instead of the prior :
dev->priv_flags &= ~IFF_XMIT_DST_RELEASE;
->
netif_keep_dst(dev);
Instead of using a single bit, we use two bits, one being
eventually rebuilt in bonding/team drivers.
The other one, is permanent and blocks IFF_XMIT_DST_RELEASE being
rebuilt in bonding/team. Eventually, we could add something
smarter later.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Probably not a big deal, but we'd better just use the
one we get in retry loop.
Fixes: commit 22e0f8b9322cb1a48b1357e8 ("net: sched: make bstats per cpu and estimator RCU safe")
Reported-by: Joe Perches <joe@perches.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a openvswitch compilation error when CONFIG_INET is not set:
=====================================================
In file included from include/net/geneve.h:4:0,
from net/openvswitch/flow_netlink.c:45:
include/net/udp_tunnel.h: In function 'udp_tunnel_handle_offloads':
>> include/net/udp_tunnel.h:100:2: error: implicit declaration of function 'iptunnel_handle_offloads' [-Werror=implicit-function-declaration]
>> return iptunnel_handle_offloads(skb, udp_csum, type);
>> ^
>> >> include/net/udp_tunnel.h:100:2: warning: return makes pointer from integer without a cast
>> >> cc1: some warnings being treated as errors
=====================================================
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a sparse warning introduced by commit:
f5796684069e0c71c65bce6a6d4766114aec1396 (openvswitch: Add support for
Geneve tunneling.) caught by kbuild test robot:
reproduce:
# apt-get install sparse
# git checkout f5796684069e0c71c65bce6a6d4766114aec1396
# make ARCH=x86_64 allmodconfig
# make C=1 CF=-D__CHECK_ENDIAN__
#
#
# sparse warnings: (new ones prefixed by >>)
#
# >> net/openvswitch/vport-geneve.c:109:15: sparse: incorrect type in assignment (different base types)
# net/openvswitch/vport-geneve.c:109:15: expected restricted __be16 [usertype] sport
# net/openvswitch/vport-geneve.c:109:15: got int
# >> net/openvswitch/vport-geneve.c:110:56: sparse: incorrect type in argument 3 (different base types)
# net/openvswitch/vport-geneve.c:110:56: expected unsigned short [unsigned] [usertype] value
# net/openvswitch/vport-geneve.c:110:56: got restricted __be16 [usertype] sport
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a sparse warning introduced by Commit
0b5e8b8eeae40bae6ad7c7e91c97c3c0d0e57882 (net: Add Geneve tunneling
protocol driver) caught by kbuild test robot:
# apt-get install sparse
# git checkout 0b5e8b8eeae40bae6ad7c7e91c97c3c0d0e57882
# make ARCH=x86_64 allmodconfig
# make C=1 CF=-D__CHECK_ENDIAN__
#
#
# sparse warnings: (new ones prefixed by >>)
#
# >> net/ipv4/geneve.c:230:42: sparse: incorrect type in assignment (different base types)
# net/ipv4/geneve.c:230:42: expected restricted __be32 [addressable] [assigned] [usertype] s_addr
# net/ipv4/geneve.c:230:42: got unsigned long [unsigned] <noident>
#
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: YOSHIFUJI Hideaki <hideaki@yoshifuji.org>
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Try to reduce number of possible fn_sernum mutation by constraining them
to their namespace.
Also remove rt_genid which I forgot to remove in 705f1c869d577c ("ipv6:
remove rt6i_genid").
Cc: YOSHIFUJI Hideaki <hideaki@yoshifuji.org>
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: YOSHIFUJI Hideaki <hideaki@yoshifuji.org>
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: YOSHIFUJI Hideaki <hideaki@yoshifuji.org>
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Also renamed struct fib6_walker_t to fib6_walker and enum fib_walk_state_t
to fib6_walk_state as recommended by Cong Wang.
Cc: Cong Wang <cwang@twopensource.com>
Cc: YOSHIFUJI Hideaki <hideaki@yoshifuji.org>
Cc: Martin Lau <kafai@fb.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marking this as static allows compiler to inline it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
-Add __rcu annotation on table to fix sparse warnings:
net/phonet/pn_dev.c:279:25: warning: incorrect type in assignment (different address spaces)
net/phonet/pn_dev.c:279:25: expected struct net_device *<noident>
net/phonet/pn_dev.c:279:25: got void [noderef] <asn:4>*<noident>
net/phonet/pn_dev.c:376:17: warning: incorrect type in assignment (different address spaces)
net/phonet/pn_dev.c:376:17: expected struct net_device *volatile <noident>
net/phonet/pn_dev.c:376:17: got struct net_device [noderef] <asn:4>*<noident>
net/phonet/pn_dev.c:392:17: warning: incorrect type in assignment (different address spaces)
net/phonet/pn_dev.c:392:17: expected struct net_device *<noident>
net/phonet/pn_dev.c:392:17: got void [noderef] <asn:4>*<noident>
-Access table with rcu_access_pointer (fixes the following sparse errors):
net/phonet/pn_dev.c:278:25: error: incompatible types in comparison expression (different address spaces)
net/phonet/pn_dev.c:391:17: error: incompatible types in comparison expression (different address spaces)
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using the tcf_proto pointer 'tp' from inside the classifiers callback
is not valid because it may have been cleaned up by another call_rcu
occuring on another CPU.
'tp' is currently being used by tcf_unbind_filter() in this patch we
move instances of tcf_unbind_filter outside of the call_rcu() context.
This is safe to do because any running schedulers will either read the
valid class field or it will be zeroed.
And all schedulers today when the class is 0 do a lookup using the
same call used by the tcf_exts_bind(). So even if we have a running
classifier hit the null class pointer it will do a lookup and get
to the same result. This is particularly fragile at the moment because
the only way to verify this is to audit the schedulers call sites.
Reported-by: Cong Wang <xiyou.wangconf@gmail.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is not RCU safe to destroy the action chain while there
is a possibility of readers accessing it. Move this code
into the rcu callback using the same rcu callback used in the
code patch to make a change to head.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This removes the tcf_proto argument from the ematch code paths that
only need it to reference the net namespace. This allows simplifying
qdisc code paths especially when we need to tear down the ematch
from an RCU callback. In this case we can not guarentee that the
tcf_proto structure is still valid.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some TSO engines might have a too heavy setup cost, that impacts
performance on hosts sending small bursts (2 MSS per packet).
This patch adds a device gso_min_segs, allowing drivers to set
a minimum segment size for TSO packets, according to the NIC
performance.
Tested on a mlx4 NIC, this allows to get a ~110% increase of
throughput when sending 2 MSS per packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we find a general query with non-zero number of sources, we
are dropping the skb as it's malformed.
RFC3376, section 4.1.8. Number of Sources (N):
This number is zero in a General Query or a Group-Specific Query,
and non-zero in a Group-and-Source-Specific Query.
Therefore, reflect that by using kfree_skb() instead of consume_skb().
Fixes: d679c5324d9a ("igmp: avoid drop_monitor false positives")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use new ethtool [sg]et_tunable() to set tx_copybread (inline threshold)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Standard qdisc API to setup a timer implies an atomic operation on every
packet dequeue : qdisc_unthrottled()
It turns out this is not really needed for FQ, as FQ has no concept of
global qdisc throttling, being a qdisc handling many different flows,
some of them can be throttled, while others are not.
Fix is straightforward : add a 'bool throttle' to
qdisc_watchdog_schedule_ns(), and remove calls to qdisc_unthrottled()
in sch_fq.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Its unfortunate we have to walk again skb list to find the tail
after segmentation, even if data is probably hot in cpu caches.
skb_segment() can store the tail of the list into segs->prev,
and validate_xmit_skb_list() can immediately get the tail.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Openvswitch implementation is completely agnostic to the options
that are in use and can handle newly defined options without
further work. It does this by simply matching on a byte array
of options and allowing userspace to setup flows on this array.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Singed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Thomas Graf <tgraf@noironetworks.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the size of the flow key grows, it can put some pressure on the
stack. This is particularly true in ovs_flow_cmd_set(), which needs several
copies of the key on the stack. One of those uses is logically separate,
so this factors it out to reduce stack pressure and improve readibility.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the flow information that is matched for tunnels and
the tunnel data passed around with packets is the same. However,
as additional information is added this is not necessarily desirable,
as in the case of pointers.
This adds a new structure for tunnel metadata which currently contains
only the existing struct. This change is purely internal to the kernel
since the current OVS_KEY_ATTR_IPV4_TUNNEL is simply a compressed version
of OVS_KEY_ATTR_TUNNEL that is translated at flow setup.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some tunnel formats have mechanisms for indicating that packets are
OAM frames that should be handled specially (either as high priority or
not forwarded beyond an endpoint). This provides support for allowing
those types of packets to be matched.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As new protocols are added, the size of the flow key tends to
increase although few protocols care about all of the fields. In
order to optimize this for hashing and matching, OVS uses a variable
length portion of the key. However, when fields are extracted from
the packet we must still zero out the entire key.
This is no longer necessary now that OVS implements masking. Any
fields (or holes in the structure) which are not part of a given
protocol will be by definition not part of the mask and zeroed out
during lookup. Furthermore, since masking already uses variable
length keys this zeroing operation automatically benefits as well.
In principle, the only thing that needs to be done at this point
is remove the memset() at the beginning of flow. However, some
fields assume that they are initialized to zero, which now must be
done explicitly. In addition, in the event of an error we must also
zero out corresponding fields to signal that there is no valid data
present. These increase the total amount of code but very little of
it is executed in non-error situations.
Removing the memset() reduces the profile of ovs_flow_extract()
from 0.64% to 0.56% when tested with large packets on a 10G link.
Suggested-by: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds a device level support for Geneve -- Generic Network
Virtualization Encapsulation. The protocol is documented at
http://tools.ietf.org/html/draft-gross-geneve-01
Only protocol layer Geneve support is provided by this driver.
Openvswitch can be used for configuring, set up and tear down
functional Geneve tunnels.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently association restarts do not take into consideration the
state of the socket. When a restart happens, the current assocation
simply transitions into established state. This creates a condition
where a remote system, through a the restart procedure, may create a
local association that is no way reachable by user. The conditions
to trigger this are as follows:
1) Remote does not acknoledge some data causing data to remain
outstanding.
2) Local application calls close() on the socket. Since data
is still outstanding, the association is placed in SHUTDOWN_PENDING
state. However, the socket is closed.
3) The remote tries to create a new association, triggering a restart
on the local system. The association moves from SHUTDOWN_PENDING
to ESTABLISHED. At this point, it is no longer reachable by
any socket on the local system.
This patch addresses the above situation by moving the newly ESTABLISHED
association into SHUTDOWN-SENT state and bundling a SHUTDOWN after
the COOKIE-ACK chunk. This way, the restarted associate immidiately
enters the shutdown procedure and forces the termination of the
unreachable association.
Reported-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
pull request: wireless-next 2014-10-03
Please pull tihs batch of updates intended for the 3.18 stream!
For the iwlwifi bits, Emmanuel says:
"I have here a few things that depend on the latest mac80211's changes:
RRM, TPC, Quiet Period etc... Eyal keeps improving our rate control
and we have a new device ID. This last patch should probably have
gone to wireless.git, but at that stage, I preferred to send it to
-next and CC stable."
For (most of) the Atheros bits, Kalle says:
"The only new feature is testmode support from me. Ben added a new method
to crash the firmware with an assert for debug purposes. As usual, we
have lots of smaller fixes from Michal. Matteo fixed a Kconfig
dependency with debugfs. I fixed some warnings recently added to
checkpatch."
For the NFC bits, Samuel says:
"We've had major updates for TI and ST Microelectronics drivers, and a
few NCI related changes.
For TI's trf7970a driver:
- Target mode support for trf7970a
- Suspend/resume support for trf7970a
- DT properties additions to handle different quirks
- A bunch of fixes for smartphone IOP related issues
For ST Microelectronics' ST21NFCA and ST21NFCB drivers:
- ISO15693 support for st21nfcb
- checkpatch and sparse related warning fixes
- Code cleanups and a few minor fixes
Finally, Marvell added ISO15693 support to the NCI stack, together with a
couple of NCI fixes."
For the Bluetooth bits, Johan says:
"This 3.18 pull request replaces the one I did on Monday ("bluetooth-next
2014-09-22", which hasn't been pulled yet). The additions since the last
request are:
- SCO connection fix for devices not supporting eSCO
- Cleanups regarding the SCO establishment logic
- Remove unnecessary return value from logging functions
- Header compression fix for 6lowpan
- Cleanups to the ieee802154/mrf24j40 driver
Here's a copy from previous request that this one replaces:
'
Here are some more patches for 3.18. They include various fixes to the
btusb HCI driver, a fix for LE SMP, as well as adding Jukka to the
MAINTAINERS file for generic 6LoWPAN (as requested by Alexander Aring).
I've held on to this pull request a bit since we were waiting for a SCO
related fix to get sorted out first. However, since the merge window is
getting closer I decided not to wait for it. If we do get the fix sorted
out there'll probably be a second small pull request later this week.
'"
And,
"Unless 3.17 gets delayed this will probably be our last -next pull request for
3.18. We've got:
- New Marvell hardware supportr
- Multicast support for 6lowpan
- Several of 6lowpan fixes & cleanups
- Fix for a (false-positive) lockdep warning in L2CAP
- Minor btusb cleanup"
On top of all that comes the usual sort of updates to ath5k, ath9k,
ath10k, brcmfmac, mwifiex, and wil6210. This time around there are
also a number of rtlwifi updates to enable some new hardware and
to reconcile the in-kernel drivers with some newer releases of the
Realtek vendor drivers. Also of note is some device tree work for
the bcma bus.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
