EXYNOS: Move files from board/samsung to arch/arm

This patch performs the following:

1) Convert the assembly code for memory and clock initialization to C code.
2) Move the memory and clock init codes from board/samsung to arch/arm
3) Creat a common lowlevel_init file across Exynos4 and Exynos5. Converted
   the common lowlevel_init from assembly to C-code
4) Made spl_boot.c and tzpc_init.c common for both exynos4 and exynos5.
5) Enable CONFIG_SKIP_LOWLEVEL_INIT as stack pointer initialisation is already
   done in _main.
6) exynos-uboot-spl.lds made common across SMDKV310, Origen and SMDK5250.

TEST: Tested SD-MMC boot on SMDK5250 and Origen.
      Tested USB and SPI boot on SMDK5250
      Compile tested for SMDKV310.

Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

13 files changed, 3081 insertions, 10 deletions

diff --git a/arch/arm/cpu/armv7/exynos/Makefile b/arch/arm/cpu/armv7/exynos/Makefile
index b2f9152..4661155 100644
--- a/arch/arm/cpu/armv7/exynos/Makefile
+++ b/arch/arm/cpu/armv7/exynos/Makefile
@@ -22,10 +22,19 @@ include $(TOPDIR)/config.mk
 
 LIB	= $(obj)lib$(SOC).o
 
-COBJS	+= clock.o power.o soc.o system.o pinmux.o tzpc.o
-
-SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS	:= $(addprefix $(obj),$(COBJS) $(SOBJS))
+COBJS-y	+= clock.o power.o soc.o system.o pinmux.o tzpc.o
+
+ifdef CONFIG_SPL_BUILD
+COBJS-$(CONFIG_EXYNOS5)	+= clock_init_exynos5.o
+COBJS-$(CONFIG_EXYNOS5)	+= dmc_common.o dmc_init_ddr3.o
+COBJS-$(CONFIG_EXYNOS4210)+= dmc_init_exynos4.o clock_init_exynos4.o
+COBJS-y	+= spl_boot.o
+COBJS-y	+= lowlevel_init.o
+endif
+
+COBJS   := $(COBJS-y)
+SRCS	:= $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
 
 all:	 $(obj).depend $(LIB)
 
diff --git a/arch/arm/cpu/armv7/exynos/clock_init.h b/arch/arm/cpu/armv7/exynos/clock_init.h
new file mode 100644
index 0000000..20a1d47
--- /dev/null
+++ b/arch/arm/cpu/armv7/exynos/clock_init.h
@@ -0,0 +1,154 @@
+/*
+ * Clock initialization routines
+ *
+ * Copyright (c) 2011 The Chromium OS Authors.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __EXYNOS_CLOCK_INIT_H
+#define __EXYNOS_CLOCK_INIT_H
+
+enum {
+	MEM_TIMINGS_MSR_COUNT	= 4,
+};
+
+/* These are the ratio's for configuring ARM clock */
+struct arm_clk_ratios {
+	unsigned arm_freq_mhz;		/* Frequency of ARM core in MHz */
+
+	unsigned apll_mdiv;
+	unsigned apll_pdiv;
+	unsigned apll_sdiv;
+
+	unsigned arm2_ratio;
+	unsigned apll_ratio;
+	unsigned pclk_dbg_ratio;
+	unsigned atb_ratio;
+	unsigned periph_ratio;
+	unsigned acp_ratio;
+	unsigned cpud_ratio;
+	unsigned arm_ratio;
+};
+
+/* These are the memory timings for a particular memory type and speed */
+struct mem_timings {
+	enum mem_manuf mem_manuf;	/* Memory manufacturer */
+	enum ddr_mode mem_type;		/* Memory type */
+	unsigned frequency_mhz;		/* Frequency of memory in MHz */
+
+	/* Here follow the timing parameters for the selected memory */
+	unsigned apll_mdiv;
+	unsigned apll_pdiv;
+	unsigned apll_sdiv;
+	unsigned mpll_mdiv;
+	unsigned mpll_pdiv;
+	unsigned mpll_sdiv;
+	unsigned cpll_mdiv;
+	unsigned cpll_pdiv;
+	unsigned cpll_sdiv;
+	unsigned gpll_mdiv;
+	unsigned gpll_pdiv;
+	unsigned gpll_sdiv;
+	unsigned epll_mdiv;
+	unsigned epll_pdiv;
+	unsigned epll_sdiv;
+	unsigned vpll_mdiv;
+	unsigned vpll_pdiv;
+	unsigned vpll_sdiv;
+	unsigned bpll_mdiv;
+	unsigned bpll_pdiv;
+	unsigned bpll_sdiv;
+	unsigned pclk_cdrex_ratio;
+	unsigned direct_cmd_msr[MEM_TIMINGS_MSR_COUNT];
+
+	unsigned timing_ref;
+	unsigned timing_row;
+	unsigned timing_data;
+	unsigned timing_power;
+
+	/* DQS, DQ, DEBUG offsets */
+	unsigned phy0_dqs;
+	unsigned phy1_dqs;
+	unsigned phy0_dq;
+	unsigned phy1_dq;
+	unsigned phy0_tFS;
+	unsigned phy1_tFS;
+	unsigned phy0_pulld_dqs;
+	unsigned phy1_pulld_dqs;
+
+	unsigned lpddr3_ctrl_phy_reset;
+	unsigned ctrl_start_point;
+	unsigned ctrl_inc;
+	unsigned ctrl_start;
+	unsigned ctrl_dll_on;
+	unsigned ctrl_ref;
+
+	unsigned ctrl_force;
+	unsigned ctrl_rdlat;
+	unsigned ctrl_bstlen;
+
+	unsigned fp_resync;
+	unsigned iv_size;
+	unsigned dfi_init_start;
+	unsigned aref_en;
+
+	unsigned rd_fetch;
+
+	unsigned zq_mode_dds;
+	unsigned zq_mode_term;
+	unsigned zq_mode_noterm;	/* 1 to allow termination disable */
+
+	unsigned memcontrol;
+	unsigned memconfig;
+
+	unsigned membaseconfig0;
+	unsigned membaseconfig1;
+	unsigned prechconfig_tp_cnt;
+	unsigned dpwrdn_cyc;
+	unsigned dsref_cyc;
+	unsigned concontrol;
+	/* Channel and Chip Selection */
+	uint8_t dmc_channels;		/* number of memory channels */
+	uint8_t chips_per_channel;	/* number of chips per channel */
+	uint8_t chips_to_configure;	/* number of chips to configure */
+	uint8_t send_zq_init;		/* 1 to send this command */
+	unsigned impedance;		/* drive strength impedeance */
+	uint8_t gate_leveling_enable;	/* check gate leveling is enabled */
+};
+
+/**
+ * Get the correct memory timings for our selected memory type and speed.
+ *
+ * This function can be called from SPL or the main U-Boot.
+ *
+ * @return pointer to the memory timings that we should use
+ */
+struct mem_timings *clock_get_mem_timings(void);
+
+/*
+ * Initialize clock for the device
+ */
+void system_clock_init(void);
+
+/*
+ * Set clock divisor value for booting from EMMC.
+ */
+void emmc_boot_clk_div_set(void);
+#endif
diff --git a/arch/arm/cpu/armv7/exynos/clock_init_exynos4.c b/arch/arm/cpu/armv7/exynos/clock_init_exynos4.c
new file mode 100644
index 0000000..3161090
--- /dev/null
+++ b/arch/arm/cpu/armv7/exynos/clock_init_exynos4.c
@@ -0,0 +1,95 @@
+/*
+ * Clock Initialization for board based on EXYNOS4210
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ * Rajeshwari Shinde <rajeshwari.s@samsung.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <config.h>
+#include <version.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/clock.h>
+#include "common_setup.h"
+#include "exynos4_setup.h"
+
+/*
+ * system_clock_init: Initialize core clock and bus clock.
+ * void system_clock_init(void)
+ */
+void system_clock_init(void)
+{
+	struct exynos4_clock *clk =
+			(struct exynos4_clock *)samsung_get_base_clock();
+
+	writel(CLK_SRC_CPU_VAL, &clk->src_cpu);
+
+	sdelay(0x10000);
+
+	writel(CLK_SRC_TOP0_VAL, &clk->src_top0);
+	writel(CLK_SRC_TOP1_VAL, &clk->src_top1);
+	writel(CLK_SRC_DMC_VAL, &clk->src_dmc);
+	writel(CLK_SRC_LEFTBUS_VAL, &clk->src_leftbus);
+	writel(CLK_SRC_RIGHTBUS_VAL, &clk->src_rightbus);
+	writel(CLK_SRC_FSYS_VAL, &clk->src_fsys);
+	writel(CLK_SRC_PERIL0_VAL, &clk->src_peril0);
+	writel(CLK_SRC_CAM_VAL, &clk->src_cam);
+	writel(CLK_SRC_MFC_VAL, &clk->src_mfc);
+	writel(CLK_SRC_G3D_VAL, &clk->src_g3d);
+	writel(CLK_SRC_LCD0_VAL, &clk->src_lcd0);
+
+	sdelay(0x10000);
+
+	writel(CLK_DIV_CPU0_VAL, &clk->div_cpu0);
+	writel(CLK_DIV_CPU1_VAL, &clk->div_cpu1);
+	writel(CLK_DIV_DMC0_VAL, &clk->div_dmc0);
+	writel(CLK_DIV_DMC1_VAL, &clk->div_dmc1);
+	writel(CLK_DIV_LEFTBUS_VAL, &clk->div_leftbus);
+	writel(CLK_DIV_RIGHTBUS_VAL, &clk->div_rightbus);
+	writel(CLK_DIV_TOP_VAL, &clk->div_top);
+	writel(CLK_DIV_FSYS1_VAL, &clk->div_fsys1);
+	writel(CLK_DIV_FSYS2_VAL, &clk->div_fsys2);
+	writel(CLK_DIV_FSYS3_VAL, &clk->div_fsys3);
+	writel(CLK_DIV_PERIL0_VAL, &clk->div_peril0);
+	writel(CLK_DIV_CAM_VAL, &clk->div_cam);
+	writel(CLK_DIV_MFC_VAL, &clk->div_mfc);
+	writel(CLK_DIV_G3D_VAL, &clk->div_g3d);
+	writel(CLK_DIV_LCD0_VAL, &clk->div_lcd0);
+
+	/* Set PLL locktime */
+	writel(PLL_LOCKTIME, &clk->apll_lock);
+	writel(PLL_LOCKTIME, &clk->mpll_lock);
+	writel(PLL_LOCKTIME, &clk->epll_lock);
+	writel(PLL_LOCKTIME, &clk->vpll_lock);
+
+	writel(APLL_CON1_VAL, &clk->apll_con1);
+	writel(APLL_CON0_VAL, &clk->apll_con0);
+	writel(MPLL_CON1_VAL, &clk->mpll_con1);
+	writel(MPLL_CON0_VAL, &clk->mpll_con0);
+	writel(EPLL_CON1_VAL, &clk->epll_con1);
+	writel(EPLL_CON0_VAL, &clk->epll_con0);
+	writel(VPLL_CON1_VAL, &clk->vpll_con1);
+	writel(VPLL_CON0_VAL, &clk->vpll_con0);
+
+	sdelay(0x30000);
+}
diff --git a/arch/arm/cpu/armv7/exynos/clock_init_exynos5.c b/arch/arm/cpu/armv7/exynos/clock_init_exynos5.c
new file mode 100644
index 0000000..0f9c572
--- /dev/null
+++ b/arch/arm/cpu/armv7/exynos/clock_init_exynos5.c
@@ -0,0 +1,684 @@
+/*
+ * Clock setup for SMDK5250 board based on EXYNOS5
+ *
+ * Copyright (C) 2012 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/spl.h>
+#include <asm/arch/dwmmc.h>
+
+#include "clock_init.h"
+#include "common_setup.h"
+#include "exynos5_setup.h"
+
+#define FSYS1_MMC0_DIV_MASK	0xff0f
+#define FSYS1_MMC0_DIV_VAL	0x0701
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct arm_clk_ratios arm_clk_ratios[] = {
+	{
+		.arm_freq_mhz = 600,
+
+		.apll_mdiv = 0xc8,
+		.apll_pdiv = 0x4,
+		.apll_sdiv = 0x1,
+
+		.arm2_ratio = 0x0,
+		.apll_ratio = 0x1,
+		.pclk_dbg_ratio = 0x1,
+		.atb_ratio = 0x2,
+		.periph_ratio = 0x7,
+		.acp_ratio = 0x7,
+		.cpud_ratio = 0x1,
+		.arm_ratio = 0x0,
+	}, {
+		.arm_freq_mhz = 800,
+
+		.apll_mdiv = 0x64,
+		.apll_pdiv = 0x3,
+		.apll_sdiv = 0x0,
+
+		.arm2_ratio = 0x0,
+		.apll_ratio = 0x1,
+		.pclk_dbg_ratio = 0x1,
+		.atb_ratio = 0x3,
+		.periph_ratio = 0x7,
+		.acp_ratio = 0x7,
+		.cpud_ratio = 0x2,
+		.arm_ratio = 0x0,
+	}, {
+		.arm_freq_mhz = 1000,
+
+		.apll_mdiv = 0x7d,
+		.apll_pdiv = 0x3,
+		.apll_sdiv = 0x0,
+
+		.arm2_ratio = 0x0,
+		.apll_ratio = 0x1,
+		.pclk_dbg_ratio = 0x1,
+		.atb_ratio = 0x4,
+		.periph_ratio = 0x7,
+		.acp_ratio = 0x7,
+		.cpud_ratio = 0x2,
+		.arm_ratio = 0x0,
+	}, {
+		.arm_freq_mhz = 1200,
+
+		.apll_mdiv = 0x96,
+		.apll_pdiv = 0x3,
+		.apll_sdiv = 0x0,
+
+		.arm2_ratio = 0x0,
+		.apll_ratio = 0x3,
+		.pclk_dbg_ratio = 0x1,
+		.atb_ratio = 0x5,
+		.periph_ratio = 0x7,
+		.acp_ratio = 0x7,
+		.cpud_ratio = 0x3,
+		.arm_ratio = 0x0,
+	}, {
+		.arm_freq_mhz = 1400,
+
+		.apll_mdiv = 0xaf,
+		.apll_pdiv = 0x3,
+		.apll_sdiv = 0x0,
+
+		.arm2_ratio = 0x0,
+		.apll_ratio = 0x3,
+		.pclk_dbg_ratio = 0x1,
+		.atb_ratio = 0x6,
+		.periph_ratio = 0x7,
+		.acp_ratio = 0x7,
+		.cpud_ratio = 0x3,
+		.arm_ratio = 0x0,
+	}, {
+		.arm_freq_mhz = 1700,
+
+		.apll_mdiv = 0x1a9,
+		.apll_pdiv = 0x6,
+		.apll_sdiv = 0x0,
+
+		.arm2_ratio = 0x0,
+		.apll_ratio = 0x3,
+		.pclk_dbg_ratio = 0x1,
+		.atb_ratio = 0x6,
+		.periph_ratio = 0x7,
+		.acp_ratio = 0x7,
+		.cpud_ratio = 0x3,
+		.arm_ratio = 0x0,
+	}
+};
+struct mem_timings mem_timings[] = {
+	{
+		.mem_manuf = MEM_MANUF_ELPIDA,
+		.mem_type = DDR_MODE_DDR3,
+		.frequency_mhz = 800,
+		.mpll_mdiv = 0xc8,
+		.mpll_pdiv = 0x3,
+		.mpll_sdiv = 0x0,
+		.cpll_mdiv = 0xde,
+		.cpll_pdiv = 0x4,
+		.cpll_sdiv = 0x2,
+		.gpll_mdiv = 0x215,
+		.gpll_pdiv = 0xc,
+		.gpll_sdiv = 0x1,
+		.epll_mdiv = 0x60,
+		.epll_pdiv = 0x3,
+		.epll_sdiv = 0x3,
+		.vpll_mdiv = 0x96,
+		.vpll_pdiv = 0x3,
+		.vpll_sdiv = 0x2,
+
+		.bpll_mdiv = 0x64,
+		.bpll_pdiv = 0x3,
+		.bpll_sdiv = 0x0,
+		.pclk_cdrex_ratio = 0x5,
+		.direct_cmd_msr = {
+			0x00020018, 0x00030000, 0x00010042, 0x00000d70
+		},
+		.timing_ref = 0x000000bb,
+		.timing_row = 0x8c36650e,
+		.timing_data = 0x3630580b,
+		.timing_power = 0x41000a44,
+		.phy0_dqs = 0x08080808,
+		.phy1_dqs = 0x08080808,
+		.phy0_dq = 0x08080808,
+		.phy1_dq = 0x08080808,
+		.phy0_tFS = 0x4,
+		.phy1_tFS = 0x4,
+		.phy0_pulld_dqs = 0xf,
+		.phy1_pulld_dqs = 0xf,
+
+		.lpddr3_ctrl_phy_reset = 0x1,
+		.ctrl_start_point = 0x10,
+		.ctrl_inc = 0x10,
+		.ctrl_start = 0x1,
+		.ctrl_dll_on = 0x1,
+		.ctrl_ref = 0x8,
+
+		.ctrl_force = 0x1a,
+		.ctrl_rdlat = 0x0b,
+		.ctrl_bstlen = 0x08,
+
+		.fp_resync = 0x8,
+		.iv_size = 0x7,
+		.dfi_init_start = 1,
+		.aref_en = 1,
+
+		.rd_fetch = 0x3,
+
+		.zq_mode_dds = 0x7,
+		.zq_mode_term = 0x1,
+		.zq_mode_noterm = 0,
+
+		/*
+		* Dynamic Clock: Always Running
+		* Memory Burst length: 8
+		* Number of chips: 1
+		* Memory Bus width: 32 bit
+		* Memory Type: DDR3
+		* Additional Latancy for PLL: 0 Cycle
+		*/
+		.memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
+			DMC_MEMCONTROL_DPWRDN_DISABLE |
+			DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
+			DMC_MEMCONTROL_TP_DISABLE |
+			DMC_MEMCONTROL_DSREF_ENABLE |
+			DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
+			DMC_MEMCONTROL_MEM_TYPE_DDR3 |
+			DMC_MEMCONTROL_MEM_WIDTH_32BIT |
+			DMC_MEMCONTROL_NUM_CHIP_1 |
+			DMC_MEMCONTROL_BL_8 |
+			DMC_MEMCONTROL_PZQ_DISABLE |
+			DMC_MEMCONTROL_MRR_BYTE_7_0,
+		.memconfig = DMC_MEMCONFIGX_CHIP_MAP_INTERLEAVED |
+			DMC_MEMCONFIGX_CHIP_COL_10 |
+			DMC_MEMCONFIGX_CHIP_ROW_15 |
+			DMC_MEMCONFIGX_CHIP_BANK_8,
+		.membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
+		.membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
+		.prechconfig_tp_cnt = 0xff,
+		.dpwrdn_cyc = 0xff,
+		.dsref_cyc = 0xffff,
+		.concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
+			DMC_CONCONTROL_TIMEOUT_LEVEL0 |
+			DMC_CONCONTROL_RD_FETCH_DISABLE |
+			DMC_CONCONTROL_EMPTY_DISABLE |
+			DMC_CONCONTROL_AREF_EN_DISABLE |
+			DMC_CONCONTROL_IO_PD_CON_DISABLE,
+		.dmc_channels = 2,
+		.chips_per_channel = 2,
+		.chips_to_configure = 1,
+		.send_zq_init = 1,
+		.impedance = IMP_OUTPUT_DRV_30_OHM,
+		.gate_leveling_enable = 0,
+	}, {
+		.mem_manuf = MEM_MANUF_SAMSUNG,
+		.mem_type = DDR_MODE_DDR3,
+		.frequency_mhz = 800,
+		.mpll_mdiv = 0xc8,
+		.mpll_pdiv = 0x3,
+		.mpll_sdiv = 0x0,
+		.cpll_mdiv = 0xde,
+		.cpll_pdiv = 0x4,
+		.cpll_sdiv = 0x2,
+		.gpll_mdiv = 0x215,
+		.gpll_pdiv = 0xc,
+		.gpll_sdiv = 0x1,
+		.epll_mdiv = 0x60,
+		.epll_pdiv = 0x3,
+		.epll_sdiv = 0x3,
+		.vpll_mdiv = 0x96,
+		.vpll_pdiv = 0x3,
+		.vpll_sdiv = 0x2,
+
+		.bpll_mdiv = 0x64,
+		.bpll_pdiv = 0x3,
+		.bpll_sdiv = 0x0,
+		.pclk_cdrex_ratio = 0x5,
+		.direct_cmd_msr = {
+			0x00020018, 0x00030000, 0x00010000, 0x00000d70
+		},
+		.timing_ref = 0x000000bb,
+		.timing_row = 0x8c36650e,
+		.timing_data = 0x3630580b,
+		.timing_power = 0x41000a44,
+		.phy0_dqs = 0x08080808,
+		.phy1_dqs = 0x08080808,
+		.phy0_dq = 0x08080808,
+		.phy1_dq = 0x08080808,
+		.phy0_tFS = 0x8,
+		.phy1_tFS = 0x8,
+		.phy0_pulld_dqs = 0xf,
+		.phy1_pulld_dqs = 0xf,
+
+		.lpddr3_ctrl_phy_reset = 0x1,
+		.ctrl_start_point = 0x10,
+		.ctrl_inc = 0x10,
+		.ctrl_start = 0x1,
+		.ctrl_dll_on = 0x1,
+		.ctrl_ref = 0x8,
+
+		.ctrl_force = 0x1a,
+		.ctrl_rdlat = 0x0b,
+		.ctrl_bstlen = 0x08,
+
+		.fp_resync = 0x8,
+		.iv_size = 0x7,
+		.dfi_init_start = 1,
+		.aref_en = 1,
+
+		.rd_fetch = 0x3,
+
+		.zq_mode_dds = 0x5,
+		.zq_mode_term = 0x1,
+		.zq_mode_noterm = 1,
+
+		/*
+		* Dynamic Clock: Always Running
+		* Memory Burst length: 8
+		* Number of chips: 1
+		* Memory Bus width: 32 bit
+		* Memory Type: DDR3
+		* Additional Latancy for PLL: 0 Cycle
+		*/
+		.memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
+			DMC_MEMCONTROL_DPWRDN_DISABLE |
+			DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
+			DMC_MEMCONTROL_TP_DISABLE |
+			DMC_MEMCONTROL_DSREF_ENABLE |
+			DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
+			DMC_MEMCONTROL_MEM_TYPE_DDR3 |
+			DMC_MEMCONTROL_MEM_WIDTH_32BIT |
+			DMC_MEMCONTROL_NUM_CHIP_1 |
+			DMC_MEMCONTROL_BL_8 |
+			DMC_MEMCONTROL_PZQ_DISABLE |
+			DMC_MEMCONTROL_MRR_BYTE_7_0,
+		.memconfig = DMC_MEMCONFIGX_CHIP_MAP_INTERLEAVED |
+			DMC_MEMCONFIGX_CHIP_COL_10 |
+			DMC_MEMCONFIGX_CHIP_ROW_15 |
+			DMC_MEMCONFIGX_CHIP_BANK_8,
+		.membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
+		.membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
+		.prechconfig_tp_cnt = 0xff,
+		.dpwrdn_cyc = 0xff,
+		.dsref_cyc = 0xffff,
+		.concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
+			DMC_CONCONTROL_TIMEOUT_LEVEL0 |
+			DMC_CONCONTROL_RD_FETCH_DISABLE |
+			DMC_CONCONTROL_EMPTY_DISABLE |
+			DMC_CONCONTROL_AREF_EN_DISABLE |
+			DMC_CONCONTROL_IO_PD_CON_DISABLE,
+		.dmc_channels = 2,
+		.chips_per_channel = 2,
+		.chips_to_configure = 1,
+		.send_zq_init = 1,
+		.impedance = IMP_OUTPUT_DRV_40_OHM,
+		.gate_leveling_enable = 1,
+	}
+};
+
+/**
+ * Get the required memory type and speed (SPL version).
+ *
+ * In SPL we have no device tree, so we use the machine parameters
+ *
+ * @param mem_type	Returns memory type
+ * @param frequency_mhz	Returns memory speed in MHz
+ * @param arm_freq	Returns ARM clock speed in MHz
+ * @param mem_manuf	Return Memory Manufacturer name
+ */
+static void clock_get_mem_selection(enum ddr_mode *mem_type,
+		unsigned *frequency_mhz, unsigned *arm_freq,
+		enum mem_manuf *mem_manuf)
+{
+	struct spl_machine_param *params;
+
+	params = spl_get_machine_params();
+	*mem_type = params->mem_type;
+	*frequency_mhz = params->frequency_mhz;
+	*arm_freq = params->arm_freq_mhz;
+	*mem_manuf = params->mem_manuf;
+}
+
+/* Get the ratios for setting ARM clock */
+struct arm_clk_ratios *get_arm_ratios(void)
+{
+	struct arm_clk_ratios *arm_ratio;
+	enum ddr_mode mem_type;
+	enum mem_manuf mem_manuf;
+	unsigned frequency_mhz, arm_freq;
+	int i;
+
+	clock_get_mem_selection(&mem_type, &frequency_mhz,
+				&arm_freq, &mem_manuf);
+
+	for (i = 0, arm_ratio = arm_clk_ratios; i < ARRAY_SIZE(arm_clk_ratios);
+		i++, arm_ratio++) {
+		if (arm_ratio->arm_freq_mhz == arm_freq)
+			return arm_ratio;
+	}
+
+	/* will hang if failed to find clock ratio */
+	while (1)
+		;
+
+	return NULL;
+}
+
+struct mem_timings *clock_get_mem_timings(void)
+{
+	struct mem_timings *mem;
+	enum ddr_mode mem_type;
+	enum mem_manuf mem_manuf;
+	unsigned frequency_mhz, arm_freq;
+	int i;
+
+	clock_get_mem_selection(&mem_type, &frequency_mhz,
+				&arm_freq, &mem_manuf);
+	for (i = 0, mem = mem_timings; i < ARRAY_SIZE(mem_timings);
+	     i++, mem++) {
+		if (mem->mem_type == mem_type &&
+		    mem->frequency_mhz == frequency_mhz &&
+		    mem->mem_manuf == mem_manuf)
+			return mem;
+	}
+
+	/* will hang if failed to find memory timings */
+	while (1)
+		;
+
+	return NULL;
+}
+
+void system_clock_init()
+{
+	struct exynos5_clock *clk =
+		(struct exynos5_clock *)samsung_get_base_clock();
+	struct mem_timings *mem;
+	struct arm_clk_ratios *arm_clk_ratio;
+	u32 val, tmp;
+
+	mem = clock_get_mem_timings();
+	arm_clk_ratio = get_arm_ratios();
+
+	clrbits_le32(&clk->src_cpu, MUX_APLL_SEL_MASK);
+	do {
+		val = readl(&clk->mux_stat_cpu);
+	} while ((val | MUX_APLL_SEL_MASK) != val);
+
+	clrbits_le32(&clk->src_core1, MUX_MPLL_SEL_MASK);
+	do {
+		val = readl(&clk->mux_stat_core1);
+	} while ((val | MUX_MPLL_SEL_MASK) != val);
+
+	clrbits_le32(&clk->src_top2, MUX_CPLL_SEL_MASK);
+	clrbits_le32(&clk->src_top2, MUX_EPLL_SEL_MASK);
+	clrbits_le32(&clk->src_top2, MUX_VPLL_SEL_MASK);
+	clrbits_le32(&clk->src_top2, MUX_GPLL_SEL_MASK);
+	tmp = MUX_CPLL_SEL_MASK | MUX_EPLL_SEL_MASK | MUX_VPLL_SEL_MASK
+		| MUX_GPLL_SEL_MASK;
+	do {
+		val = readl(&clk->mux_stat_top2);
+	} while ((val | tmp) != val);
+
+	clrbits_le32(&clk->src_cdrex, MUX_BPLL_SEL_MASK);
+	do {
+		val = readl(&clk->mux_stat_cdrex);
+	} while ((val | MUX_BPLL_SEL_MASK) != val);
+
+	/* PLL locktime */
+	writel(APLL_LOCK_VAL, &clk->apll_lock);
+
+	writel(MPLL_LOCK_VAL, &clk->mpll_lock);
+
+	writel(BPLL_LOCK_VAL, &clk->bpll_lock);
+
+	writel(CPLL_LOCK_VAL, &clk->cpll_lock);
+
+	writel(GPLL_LOCK_VAL, &clk->gpll_lock);
+
+	writel(EPLL_LOCK_VAL, &clk->epll_lock);
+
+	writel(VPLL_LOCK_VAL, &clk->vpll_lock);
+
+	writel(CLK_REG_DISABLE, &clk->pll_div2_sel);
+
+	writel(MUX_HPM_SEL_MASK, &clk->src_cpu);
+	do {
+		val = readl(&clk->mux_stat_cpu);
+	} while ((val | HPM_SEL_SCLK_MPLL) != val);
+
+	val = arm_clk_ratio->arm2_ratio << 28
+		| arm_clk_ratio->apll_ratio << 24
+		| arm_clk_ratio->pclk_dbg_ratio << 20
+		| arm_clk_ratio->atb_ratio << 16
+		| arm_clk_ratio->periph_ratio << 12
+		| arm_clk_ratio->acp_ratio << 8
+		| arm_clk_ratio->cpud_ratio << 4
+		| arm_clk_ratio->arm_ratio;
+	writel(val, &clk->div_cpu0);
+	do {
+		val = readl(&clk->div_stat_cpu0);
+	} while (0 != val);
+
+	writel(CLK_DIV_CPU1_VAL, &clk->div_cpu1);
+	do {
+		val = readl(&clk->div_stat_cpu1);
+	} while (0 != val);
+
+	/* Set APLL */
+	writel(APLL_CON1_VAL, &clk->apll_con1);
+	val = set_pll(arm_clk_ratio->apll_mdiv, arm_clk_ratio->apll_pdiv,
+			arm_clk_ratio->apll_sdiv);
+	writel(val, &clk->apll_con0);
+	while ((readl(&clk->apll_con0) & APLL_CON0_LOCKED) == 0)
+		;
+
+	/* Set MPLL */
+	writel(MPLL_CON1_VAL, &clk->mpll_con1);
+	val = set_pll(mem->mpll_mdiv, mem->mpll_pdiv, mem->mpll_sdiv);
+	writel(val, &clk->mpll_con0);
+	while ((readl(&clk->mpll_con0) & MPLL_CON0_LOCKED) == 0)
+		;
+
+	/* Set BPLL */
+	writel(BPLL_CON1_VAL, &clk->bpll_con1);
+	val = set_pll(mem->bpll_mdiv, mem->bpll_pdiv, mem->bpll_sdiv);
+	writel(val, &clk->bpll_con0);
+	while ((readl(&clk->bpll_con0) & BPLL_CON0_LOCKED) == 0)
+		;
+
+	/* Set CPLL */
+	writel(CPLL_CON1_VAL, &clk->cpll_con1);
+	val = set_pll(mem->cpll_mdiv, mem->cpll_pdiv, mem->cpll_sdiv);
+	writel(val, &clk->cpll_con0);
+	while ((readl(&clk->cpll_con0) & CPLL_CON0_LOCKED) == 0)
+		;
+
+	/* Set GPLL */
+	writel(GPLL_CON1_VAL, &clk->gpll_con1);
+	val = set_pll(mem->gpll_mdiv, mem->gpll_pdiv, mem->gpll_sdiv);
+	writel(val, &clk->gpll_con0);
+	while ((readl(&clk->gpll_con0) & GPLL_CON0_LOCKED) == 0)
+		;
+
+	/* Set EPLL */
+	writel(EPLL_CON2_VAL, &clk->epll_con2);
+	writel(EPLL_CON1_VAL, &clk->epll_con1);
+	val = set_pll(mem->epll_mdiv, mem->epll_pdiv, mem->epll_sdiv);
+	writel(val, &clk->epll_con0);
+	while ((readl(&clk->epll_con0) & EPLL_CON0_LOCKED) == 0)
+		;
+
+	/* Set VPLL */
+	writel(VPLL_CON2_VAL, &clk->vpll_con2);
+	writel(VPLL_CON1_VAL, &clk->vpll_con1);
+	val = set_pll(mem->vpll_mdiv, mem->vpll_pdiv, mem->vpll_sdiv);
+	writel(val, &clk->vpll_con0);
+	while ((readl(&clk->vpll_con0) & VPLL_CON0_LOCKED) == 0)
+		;
+
+	writel(CLK_SRC_CORE0_VAL, &clk->src_core0);
+	writel(CLK_DIV_CORE0_VAL, &clk->div_core0);
+	while (readl(&clk->div_stat_core0) != 0)
+		;
+
+	writel(CLK_DIV_CORE1_VAL, &clk->div_core1);
+	while (readl(&clk->div_stat_core1) != 0)
+		;
+
+	writel(CLK_DIV_SYSRGT_VAL, &clk->div_sysrgt);
+	while (readl(&clk->div_stat_sysrgt) != 0)
+		;
+
+	writel(CLK_DIV_ACP_VAL, &clk->div_acp);
+	while (readl(&clk->div_stat_acp) != 0)
+		;
+
+	writel(CLK_DIV_SYSLFT_VAL, &clk->div_syslft);
+	while (readl(&clk->div_stat_syslft) != 0)
+		;
+
+	writel(CLK_SRC_TOP0_VAL, &clk->src_top0);
+	writel(CLK_SRC_TOP1_VAL, &clk->src_top1);
+	writel(TOP2_VAL, &clk->src_top2);
+	writel(CLK_SRC_TOP3_VAL, &clk->src_top3);
+
+	writel(CLK_DIV_TOP0_VAL, &clk->div_top0);
+	while (readl(&clk->div_stat_top0))
+		;
+
+	writel(CLK_DIV_TOP1_VAL, &clk->div_top1);
+	while (readl(&clk->div_stat_top1))
+		;
+
+	writel(CLK_SRC_LEX_VAL, &clk->src_lex);
+	while (1) {
+		val = readl(&clk->mux_stat_lex);
+		if (val == (val | 1))
+			break;
+	}
+
+	writel(CLK_DIV_LEX_VAL, &clk->div_lex);
+	while (readl(&clk->div_stat_lex))
+		;
+
+	writel(CLK_DIV_R0X_VAL, &clk->div_r0x);
+	while (readl(&clk->div_stat_r0x))
+		;
+
+	writel(CLK_DIV_R0X_VAL, &clk->div_r0x);
+	while (readl(&clk->div_stat_r0x))
+		;
+
+	writel(CLK_DIV_R1X_VAL, &clk->div_r1x);
+	while (readl(&clk->div_stat_r1x))
+		;
+
+	writel(CLK_REG_DISABLE, &clk->src_cdrex);
+
+	writel(CLK_DIV_CDREX_VAL, &clk->div_cdrex);
+	while (readl(&clk->div_stat_cdrex))
+		;
+
+	val = readl(&clk->src_cpu);
+	val |= CLK_SRC_CPU_VAL;
+	writel(val, &clk->src_cpu);
+
+	val = readl(&clk->src_top2);
+	val |= CLK_SRC_TOP2_VAL;
+	writel(val, &clk->src_top2);
+
+	val = readl(&clk->src_core1);
+	val |= CLK_SRC_CORE1_VAL;
+	writel(val, &clk->src_core1);
+
+	writel(CLK_SRC_FSYS0_VAL, &clk->src_fsys);
+	writel(CLK_DIV_FSYS0_VAL, &clk->div_fsys0);
+	while (readl(&clk->div_stat_fsys0))
+		;
+
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_cpu);
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_core);
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_acp);
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_top);
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_lex);
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_r0x);
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_r1x);
+	writel(CLK_REG_DISABLE, &clk->clkout_cmu_cdrex);
+
+	writel(CLK_SRC_PERIC0_VAL, &clk->src_peric0);
+	writel(CLK_DIV_PERIC0_VAL, &clk->div_peric0);
+
+	writel(CLK_SRC_PERIC1_VAL, &clk->src_peric1);
+	writel(CLK_DIV_PERIC1_VAL, &clk->div_peric1);
+	writel(CLK_DIV_PERIC2_VAL, &clk->div_peric2);
+	writel(CLK_DIV_PERIC3_VAL, &clk->div_peric3);
+
+	writel(SCLK_SRC_ISP_VAL, &clk->sclk_src_isp);
+	writel(SCLK_DIV_ISP_VAL, &clk->sclk_div_isp);
+	writel(CLK_DIV_ISP0_VAL, &clk->div_isp0);
+	writel(CLK_DIV_ISP1_VAL, &clk->div_isp1);
+	writel(CLK_DIV_ISP2_VAL, &clk->div_isp2);
+
+	/* FIMD1 SRC CLK SELECTION */
+	writel(CLK_SRC_DISP1_0_VAL, &clk->src_disp1_0);
+
+	val = MMC2_PRE_RATIO_VAL << MMC2_PRE_RATIO_OFFSET
+		| MMC2_RATIO_VAL << MMC2_RATIO_OFFSET
+		| MMC3_PRE_RATIO_VAL << MMC3_PRE_RATIO_OFFSET
+		| MMC3_RATIO_VAL << MMC3_RATIO_OFFSET;
+	writel(val, &clk->div_fsys2);
+}
+
+void clock_init_dp_clock(void)
+{
+	struct exynos5_clock *clk =
+		(struct exynos5_clock *)samsung_get_base_clock();
+
+	/* DP clock enable */
+	setbits_le32(&clk->gate_ip_disp1, CLK_GATE_DP1_ALLOW);
+
+	/* We run DP at 267 Mhz */
+	setbits_le32(&clk->div_disp1_0, CLK_DIV_DISP1_0_FIMD1);
+}
+
+/*
+ * Set clock divisor value for booting from EMMC.
+ * Set DWMMC channel-0 clk div to operate mmc0 device at 50MHz.
+ */
+void emmc_boot_clk_div_set(void)
+{
+	struct exynos5_clock *clk =
+		(struct exynos5_clock *)samsung_get_base_clock();
+	unsigned int div_mmc;
+
+	div_mmc = readl((unsigned int) &clk->div_fsys1) & ~FSYS1_MMC0_DIV_MASK;
+	div_mmc |= FSYS1_MMC0_DIV_VAL;
+	writel(div_mmc, (unsigned int) &clk->div_fsys1);
+}
diff --git a/arch/arm/cpu/armv7/exynos/common_setup.h b/arch/arm/cpu/armv7/exynos/common_setup.h
new file mode 100644
index 0000000..e6318c0
--- /dev/null
+++ b/arch/arm/cpu/armv7/exynos/common_setup.h
@@ -0,0 +1,45 @@
+/*
+ * Common APIs for EXYNOS based board
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ * Rajeshwari Shinde <rajeshwari.s@samsung.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#define DMC_OFFSET	0x10000
+
+/*
+ * Memory initialization
+ *
+ * @param reset     Reset PHY during initialization.
+ */
+void mem_ctrl_init(int reset);
+
+ /* System Clock initialization */
+void system_clock_init(void);
+
+/*
+ * Init subsystems according to the reset status
+ *
+ * @return 0 for a normal boot, non-zero for a resume
+ */
+int do_lowlevel_init(void);
+
+void sdelay(unsigned long);
diff --git a/arch/arm/cpu/armv7/exynos/dmc_common.c b/arch/arm/cpu/armv7/exynos/dmc_common.c
new file mode 100644
index 0000000..645f57e
--- /dev/null
+++ b/arch/arm/cpu/armv7/exynos/dmc_common.c
@@ -0,0 +1,200 @@
+/*
+ * Mem setup common file for different types of DDR present on SMDK5250 boards.
+ *
+ * Copyright (C) 2012 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/arch/spl.h>
+
+#include "clock_init.h"
+#include "common_setup.h"
+#include "exynos5_setup.h"
+
+#define ZQ_INIT_TIMEOUT	10000
+
+int dmc_config_zq(struct mem_timings *mem,
+		  struct exynos5_phy_control *phy0_ctrl,
+		  struct exynos5_phy_control *phy1_ctrl)
+{
+	unsigned long val = 0;
+	int i;
+
+	/*
+	 * ZQ Calibration:
+	 * Select Driver Strength,
+	 * long calibration for manual calibration
+	 */
+	val = PHY_CON16_RESET_VAL;
+	val |= mem->zq_mode_dds << PHY_CON16_ZQ_MODE_DDS_SHIFT;
+	val |= mem->zq_mode_term << PHY_CON16_ZQ_MODE_TERM_SHIFT;
+	val |= ZQ_CLK_DIV_EN;
+	writel(val, &phy0_ctrl->phy_con16);
+	writel(val, &phy1_ctrl->phy_con16);
+
+	/* Disable termination */
+	if (mem->zq_mode_noterm)
+		val |= PHY_CON16_ZQ_MODE_NOTERM_MASK;
+	writel(val, &phy0_ctrl->phy_con16);
+	writel(val, &phy1_ctrl->phy_con16);
+
+	/* ZQ_MANUAL_START: Enable */
+	val |= ZQ_MANUAL_STR;
+	writel(val, &phy0_ctrl->phy_con16);
+	writel(val, &phy1_ctrl->phy_con16);
+
+	/* ZQ_MANUAL_START: Disable */
+	val &= ~ZQ_MANUAL_STR;
+
+	/*
+	 * Since we are manaully calibrating the ZQ values,
+	 * we are looping for the ZQ_init to complete.
+	 */
+	i = ZQ_INIT_TIMEOUT;
+	while ((readl(&phy0_ctrl->phy_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
+		sdelay(100);
+		i--;
+	}
+	if (!i)
+		return -1;
+	writel(val, &phy0_ctrl->phy_con16);
+
+	i = ZQ_INIT_TIMEOUT;
+	while ((readl(&phy1_ctrl->phy_con17) & ZQ_DONE) != ZQ_DONE && i > 0) {
+		sdelay(100);
+		i--;
+	}
+	if (!i)
+		return -1;
+	writel(val, &phy1_ctrl->phy_con16);
+
+	return 0;
+}
+
+void update_reset_dll(struct exynos5_dmc *dmc, enum ddr_mode mode)
+{
+	unsigned long val;
+
+	if (mode == DDR_MODE_DDR3) {
+		val = MEM_TERM_EN | PHY_TERM_EN | DMC_CTRL_SHGATE;
+		writel(val, &dmc->phycontrol0);
+	}
+
+	/* Update DLL Information: Force DLL Resyncronization */
+	val = readl(&dmc->phycontrol0);
+	val |= FP_RSYNC;
+	writel(val, &dmc->phycontrol0);
+
+	/* Reset Force DLL Resyncronization */
+	val = readl(&dmc->phycontrol0);
+	val &= ~FP_RSYNC;
+	writel(val, &dmc->phycontrol0);
+}
+
+void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc)
+{
+	int channel, chip;
+
+	for (channel = 0; channel < mem->dmc_channels; channel++) {
+		unsigned long mask;
+
+		mask = channel << DIRECT_CMD_CHANNEL_SHIFT;
+		for (chip = 0; chip < mem->chips_to_configure; chip++) {
+			int i;
+
+			mask |= chip << DIRECT_CMD_CHIP_SHIFT;
+
+			/* Sending NOP command */
+			writel(DIRECT_CMD_NOP | mask, &dmc->directcmd);
+
+			/*
+			 * TODO(alim.akhtar@samsung.com): Do we need these
+			 * delays? This one and the next were not there for
+			 * DDR3.
+			 */
+			sdelay(0x10000);
+
+			/* Sending EMRS/MRS commands */
+			for (i = 0; i < MEM_TIMINGS_MSR_COUNT; i++) {
+				writel(mem->direct_cmd_msr[i] | mask,
+				       &dmc->directcmd);
+				sdelay(0x10000);
+			}
+
+			if (mem->send_zq_init) {
+				/* Sending ZQINIT command */
+				writel(DIRECT_CMD_ZQINIT | mask,
+				       &dmc->directcmd);
+
+				sdelay(10000);
+			}
+		}
+	}
+}
+
+void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc)
+{
+	int channel, chip;
+
+	for (channel = 0; channel < mem->dmc_channels; channel++) {
+		unsigned long mask;
+
+		mask = channel << DIRECT_CMD_CHANNEL_SHIFT;
+		for (chip = 0; chip < mem->chips_per_channel; chip++) {
+			mask |= chip << DIRECT_CMD_CHIP_SHIFT;
+
+			/* PALL (all banks precharge) CMD */
+			writel(DIRECT_CMD_PALL | mask, &dmc->directcmd);
+			sdelay(0x10000);
+		}
+	}
+}
+
+void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc)
+{
+	writel(mem->memconfig, &dmc->memconfig0);
+	writel(mem->memconfig, &dmc->memconfig1);
+	writel(DMC_MEMBASECONFIG0_VAL, &dmc->membaseconfig0);
+	writel(DMC_MEMBASECONFIG1_VAL, &dmc->membaseconfig1);
+}
+
+void mem_ctrl_init(int reset)
+{
+	struct spl_machine_param *param = spl_get_machine_params();
+	struct mem_timings *mem;
+	int ret;
+
+	mem = clock_get_mem_timings();
+
+	/* If there are any other memory variant, add their init call below */
+	if (param->mem_type == DDR_MODE_DDR3) {
+		ret = ddr3_mem_ctrl_init(mem, param->mem_iv_size, reset);
+		if (ret) {
+			/* will hang if failed to init memory control */
+			while (1)
+				;
+		}
+	} else {
+		/* will hang if unknow memory type  */
+		while (1)
+			;
+	}
+}
diff --git a/arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c b/arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c
new file mode 100644
index 0000000..e03d74b
--- /dev/null
+++ b/arch/arm/cpu/armv7/exynos/dmc_init_ddr3.c
@@ -0,0 +1,233 @@
+/*
+ * DDR3 mem setup file for SMDK5250 board based on EXYNOS5
+ *
+ * Copyright (C) 2012 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/dmc.h>
+#include "common_setup.h"
+#include "exynos5_setup.h"
+#include "clock_init.h"
+
+#define RDLVL_COMPLETE_TIMEOUT	10000
+
+static void reset_phy_ctrl(void)
+{
+	struct exynos5_clock *clk =
+		(struct exynos5_clock *)samsung_get_base_clock();
+
+	writel(DDR3PHY_CTRL_PHY_RESET_OFF, &clk->lpddr3phy_ctrl);
+	writel(DDR3PHY_CTRL_PHY_RESET, &clk->lpddr3phy_ctrl);
+}
+
+int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
+		       int reset)
+{
+	unsigned int val;
+	struct exynos5_phy_control *phy0_ctrl, *phy1_ctrl;
+	struct exynos5_dmc *dmc;
+	int i;
+
+	phy0_ctrl = (struct exynos5_phy_control *)samsung_get_base_dmc_phy();
+	phy1_ctrl = (struct exynos5_phy_control *)(samsung_get_base_dmc_phy()
+							+ DMC_OFFSET);
+	dmc = (struct exynos5_dmc *)samsung_get_base_dmc_ctrl();
+
+	if (reset)
+		reset_phy_ctrl();
+
+	/* Set Impedance Output Driver */
+	val = (mem->impedance << CA_CK_DRVR_DS_OFFSET) |
+		(mem->impedance << CA_CKE_DRVR_DS_OFFSET) |
+		(mem->impedance << CA_CS_DRVR_DS_OFFSET) |
+		(mem->impedance << CA_ADR_DRVR_DS_OFFSET);
+	writel(val, &phy0_ctrl->phy_con39);
+	writel(val, &phy1_ctrl->phy_con39);
+
+	/* Set Read Latency and Burst Length for PHY0 and PHY1 */
+	val = (mem->ctrl_bstlen << PHY_CON42_CTRL_BSTLEN_SHIFT) |
+		(mem->ctrl_rdlat << PHY_CON42_CTRL_RDLAT_SHIFT);
+	writel(val, &phy0_ctrl->phy_con42);
+	writel(val, &phy1_ctrl->phy_con42);
+
+	/* ZQ Calibration */
+	if (dmc_config_zq(mem, phy0_ctrl, phy1_ctrl))
+		return SETUP_ERR_ZQ_CALIBRATION_FAILURE;
+
+	/* DQ Signal */
+	writel(mem->phy0_pulld_dqs, &phy0_ctrl->phy_con14);
+	writel(mem->phy1_pulld_dqs, &phy1_ctrl->phy_con14);
+
+	writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
+		| (mem->dfi_init_start << CONCONTROL_DFI_INIT_START_SHIFT),
+		&dmc->concontrol);
+
+	update_reset_dll(dmc, DDR_MODE_DDR3);
+
+	/* DQS Signal */
+	writel(mem->phy0_dqs, &phy0_ctrl->phy_con4);
+	writel(mem->phy1_dqs, &phy1_ctrl->phy_con4);
+
+	writel(mem->phy0_dq, &phy0_ctrl->phy_con6);
+	writel(mem->phy1_dq, &phy1_ctrl->phy_con6);
+
+	writel(mem->phy0_tFS, &phy0_ctrl->phy_con10);
+	writel(mem->phy1_tFS, &phy1_ctrl->phy_con10);
+
+	val = (mem->ctrl_start_point << PHY_CON12_CTRL_START_POINT_SHIFT) |
+		(mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
+		(mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
+		(mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
+	writel(val, &phy0_ctrl->phy_con12);
+	writel(val, &phy1_ctrl->phy_con12);
+
+	/* Start DLL locking */
+	writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
+	       &phy0_ctrl->phy_con12);
+	writel(val | (mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT),
+	       &phy1_ctrl->phy_con12);
+
+	update_reset_dll(dmc, DDR_MODE_DDR3);
+
+	writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT),
+	       &dmc->concontrol);
+
+	/* Memory Channel Inteleaving Size */
+	writel(mem->iv_size, &dmc->ivcontrol);
+
+	writel(mem->memconfig, &dmc->memconfig0);
+	writel(mem->memconfig, &dmc->memconfig1);
+	writel(mem->membaseconfig0, &dmc->membaseconfig0);
+	writel(mem->membaseconfig1, &dmc->membaseconfig1);
+
+	/* Precharge Configuration */
+	writel(mem->prechconfig_tp_cnt << PRECHCONFIG_TP_CNT_SHIFT,
+	       &dmc->prechconfig);
+
+	/* Power Down mode Configuration */
+	writel(mem->dpwrdn_cyc << PWRDNCONFIG_DPWRDN_CYC_SHIFT |
+		mem->dsref_cyc << PWRDNCONFIG_DSREF_CYC_SHIFT,
+		&dmc->pwrdnconfig);
+
+	/* TimingRow, TimingData, TimingPower and Timingaref
+	 * values as per Memory AC parameters
+	 */
+	writel(mem->timing_ref, &dmc->timingref);
+	writel(mem->timing_row, &dmc->timingrow);
+	writel(mem->timing_data, &dmc->timingdata);
+	writel(mem->timing_power, &dmc->timingpower);
+
+	/* Send PALL command */
+	dmc_config_prech(mem, dmc);
+
+	/* Send NOP, MRS and ZQINIT commands */
+	dmc_config_mrs(mem, dmc);
+
+	if (mem->gate_leveling_enable) {
+		val = PHY_CON0_RESET_VAL;
+		val |= P0_CMD_EN;
+		writel(val, &phy0_ctrl->phy_con0);
+		writel(val, &phy1_ctrl->phy_con0);
+
+		val = PHY_CON2_RESET_VAL;
+		val |= INIT_DESKEW_EN;
+		writel(val, &phy0_ctrl->phy_con2);
+		writel(val, &phy1_ctrl->phy_con2);
+
+		val = PHY_CON0_RESET_VAL;
+		val |= P0_CMD_EN;
+		val |= BYTE_RDLVL_EN;
+		writel(val, &phy0_ctrl->phy_con0);
+		writel(val, &phy1_ctrl->phy_con0);
+
+		val = (mem->ctrl_start_point <<
+				PHY_CON12_CTRL_START_POINT_SHIFT) |
+			(mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
+			(mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
+			(mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
+			(mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
+		writel(val, &phy0_ctrl->phy_con12);
+		writel(val, &phy1_ctrl->phy_con12);
+
+		val = PHY_CON2_RESET_VAL;
+		val |= INIT_DESKEW_EN;
+		val |= RDLVL_GATE_EN;
+		writel(val, &phy0_ctrl->phy_con2);
+		writel(val, &phy1_ctrl->phy_con2);
+
+		val = PHY_CON0_RESET_VAL;
+		val |= P0_CMD_EN;
+		val |= BYTE_RDLVL_EN;
+		val |= CTRL_SHGATE;
+		writel(val, &phy0_ctrl->phy_con0);
+		writel(val, &phy1_ctrl->phy_con0);
+
+		val = PHY_CON1_RESET_VAL;
+		val &= ~(CTRL_GATEDURADJ_MASK);
+		writel(val, &phy0_ctrl->phy_con1);
+		writel(val, &phy1_ctrl->phy_con1);
+
+		writel(CTRL_RDLVL_GATE_ENABLE, &dmc->rdlvl_config);
+		i = RDLVL_COMPLETE_TIMEOUT;
+		while ((readl(&dmc->phystatus) &
+			(RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1)) !=
+			(RDLVL_COMPLETE_CHO | RDLVL_COMPLETE_CH1) && i > 0) {
+			/*
+			 * TODO(waihong): Comment on how long this take to
+			 * timeout
+			 */
+			sdelay(100);
+			i--;
+		}
+		if (!i)
+			return SETUP_ERR_RDLV_COMPLETE_TIMEOUT;
+		writel(CTRL_RDLVL_GATE_DISABLE, &dmc->rdlvl_config);
+
+		writel(0, &phy0_ctrl->phy_con14);
+		writel(0, &phy1_ctrl->phy_con14);
+
+		val = (mem->ctrl_start_point <<
+				PHY_CON12_CTRL_START_POINT_SHIFT) |
+			(mem->ctrl_inc << PHY_CON12_CTRL_INC_SHIFT) |
+			(mem->ctrl_force << PHY_CON12_CTRL_FORCE_SHIFT) |
+			(mem->ctrl_start << PHY_CON12_CTRL_START_SHIFT) |
+			(mem->ctrl_dll_on << PHY_CON12_CTRL_DLL_ON_SHIFT) |
+			(mem->ctrl_ref << PHY_CON12_CTRL_REF_SHIFT);
+		writel(val, &phy0_ctrl->phy_con12);
+		writel(val, &phy1_ctrl->phy_con12);
+
+		update_reset_dll(dmc, DDR_MODE_DDR3);
+	}
+
+	/* Send PALL command */
+	dmc_config_prech(mem, dmc);
+
+	writel(mem->memcontrol, &dmc->memcontrol);
+
+	/* Set DMC Concontrol and enable auto-refresh counter */
+	writel(mem->concontrol | (mem->rd_fetch << CONCONTROL_RD_FETCH_SHIFT)
+		| (mem->aref_en << CONCONTROL_AREF_EN_SHIFT), &dmc->concontrol);
+	return 0;
+}
diff --git a/arch/arm/cpu/armv7/exynos/dmc_init_exynos4.c b/arch/arm/cpu/armv7/exynos/dmc_init_exynos4.c
new file mode 100644
index 0000000..ecddc72
--- /dev/null
+++ b/arch/arm/cpu/armv7/exynos/dmc_init_exynos4.c
@@ -0,0 +1,213 @@
+/*
+ * Memory setup for board based on EXYNOS4210
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ * Rajeshwari Shinde <rajeshwari.s@samsung.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <asm/arch/dmc.h>
+#include "common_setup.h"
+#include "exynos4_setup.h"
+
+struct mem_timings mem = {
+	.direct_cmd_msr = {
+		DIRECT_CMD1, DIRECT_CMD2, DIRECT_CMD3, DIRECT_CMD4
+	},
+	.timingref = TIMINGREF_VAL,
+	.timingrow = TIMINGROW_VAL,
+	.timingdata = TIMINGDATA_VAL,
+	.timingpower = TIMINGPOWER_VAL,
+	.zqcontrol = ZQ_CONTROL_VAL,
+	.control0 = CONTROL0_VAL,
+	.control1 = CONTROL1_VAL,
+	.control2 = CONTROL2_VAL,
+	.concontrol = CONCONTROL_VAL,
+	.prechconfig = PRECHCONFIG,
+	.memcontrol = MEMCONTROL_VAL,
+	.memconfig0 = MEMCONFIG0_VAL,
+	.memconfig1 = MEMCONFIG1_VAL,
+	.dll_resync = FORCE_DLL_RESYNC,
+	.dll_on = DLL_CONTROL_ON,
+};
+static void phy_control_reset(int ctrl_no, struct exynos4_dmc *dmc)
+{
+	if (ctrl_no) {
+		writel((mem.control1 | (1 << mem.dll_resync)),
+		       &dmc->phycontrol1);
+		writel((mem.control1 | (0 << mem.dll_resync)),
+		       &dmc->phycontrol1);
+	} else {
+		writel((mem.control0 | (0 << mem.dll_on)),
+		       &dmc->phycontrol0);
+		writel((mem.control0 | (1 << mem.dll_on)),
+		       &dmc->phycontrol0);
+	}
+}
+
+static void dmc_config_mrs(struct exynos4_dmc *dmc, int chip)
+{
+	int i;
+	unsigned long mask = 0;
+
+	if (chip)
+		mask = DIRECT_CMD_CHIP1_SHIFT;
+
+	for (i = 0; i < MEM_TIMINGS_MSR_COUNT; i++) {
+		writel(mem.direct_cmd_msr[i] | mask,
+		       &dmc->directcmd);
+	}
+}
+
+static void dmc_init(struct exynos4_dmc *dmc)
+{
+	/*
+	 * DLL Parameter Setting:
+	 * Termination: Enable R/W
+	 * Phase Delay for DQS Cleaning: 180' Shift
+	 */
+	writel(mem.control1, &dmc->phycontrol1);
+
+	/*
+	 * ZQ Calibration
+	 * Termination: Disable
+	 * Auto Calibration Start: Enable
+	 */
+	writel(mem.zqcontrol, &dmc->phyzqcontrol);
+	sdelay(0x100000);
+
+	/*
+	 * Update DLL Information:
+	 * Force DLL Resyncronization
+	 */
+	phy_control_reset(1, dmc);
+	phy_control_reset(0, dmc);
+
+	/* Set DLL Parameters */
+	writel(mem.control1, &dmc->phycontrol1);
+
+	/* DLL Start */
+	writel((mem.control0 | CTRL_START | CTRL_DLL_ON), &dmc->phycontrol0);
+
+	writel(mem.control2, &dmc->phycontrol2);
+
+	/* Set Clock Ratio of Bus clock to Memory Clock */
+	writel(mem.concontrol, &dmc->concontrol);
+
+	/*
+	 * Memor Burst length: 8
+	 * Number of chips: 2
+	 * Memory Bus width: 32 bit
+	 * Memory Type: DDR3
+	 * Additional Latancy for PLL: 1 Cycle
+	 */
+	writel(mem.memcontrol, &dmc->memcontrol);
+
+	writel(mem.memconfig0, &dmc->memconfig0);
+	writel(mem.memconfig1, &dmc->memconfig1);
+
+	/* Config Precharge Policy */
+	writel(mem.prechconfig, &dmc->prechconfig);
+	/*
+	 * TimingAref, TimingRow, TimingData, TimingPower Setting:
+	 * Values as per Memory AC Parameters
+	 */
+	writel(mem.timingref, &dmc->timingref);
+	writel(mem.timingrow, &dmc->timingrow);
+	writel(mem.timingdata, &dmc->timingdata);
+	writel(mem.timingpower, &dmc->timingpower);
+
+	/* Chip0: NOP Command: Assert and Hold CKE to high level */
+	writel(DIRECT_CMD_NOP, &dmc->directcmd);
+	sdelay(0x100000);
+
+	/* Chip0: EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
+	dmc_config_mrs(dmc, 0);
+	sdelay(0x100000);
+
+	/* Chip0: ZQINIT */
+	writel(DIRECT_CMD_ZQ, &dmc->directcmd);
+	sdelay(0x100000);
+
+	writel((DIRECT_CMD_NOP | DIRECT_CMD_CHIP1_SHIFT), &dmc->directcmd);
+	sdelay(0x100000);
+
+	/* Chip1: EMRS2, EMRS3, EMRS, MRS Commands Using Direct Command */
+	dmc_config_mrs(dmc, 1);
+	sdelay(0x100000);
+
+	/* Chip1: ZQINIT */
+	writel((DIRECT_CMD_ZQ | DIRECT_CMD_CHIP1_SHIFT), &dmc->directcmd);
+	sdelay(0x100000);
+
+	phy_control_reset(1, dmc);
+	sdelay(0x100000);
+
+	/* turn on DREX0, DREX1 */
+	writel((mem.concontrol | AREF_EN), &dmc->concontrol);
+}
+
+void mem_ctrl_init(int reset)
+{
+	struct exynos4_dmc *dmc;
+
+	/*
+	 * Async bridge configuration at CPU_core:
+	 * 1: half_sync
+	 * 0: full_sync
+	 */
+	writel(1, ASYNC_CONFIG);
+#ifdef CONFIG_ORIGEN
+	/* Interleave: 2Bit, Interleave_bit1: 0x15, Interleave_bit0: 0x7 */
+	writel(APB_SFR_INTERLEAVE_CONF_VAL, EXYNOS4_MIU_BASE +
+		APB_SFR_INTERLEAVE_CONF_OFFSET);
+	/* Update MIU Configuration */
+	writel(APB_SFR_ARBRITATION_CONF_VAL, EXYNOS4_MIU_BASE +
+		APB_SFR_ARBRITATION_CONF_OFFSET);
+#else
+	writel(APB_SFR_INTERLEAVE_CONF_VAL, EXYNOS4_MIU_BASE +
+		APB_SFR_INTERLEAVE_CONF_OFFSET);
+	writel(INTERLEAVE_ADDR_MAP_START_ADDR, EXYNOS4_MIU_BASE +
+		ABP_SFR_INTERLEAVE_ADDRMAP_START_OFFSET);
+	writel(INTERLEAVE_ADDR_MAP_END_ADDR, EXYNOS4_MIU_BASE +
+		ABP_SFR_INTERLEAVE_ADDRMAP_END_OFFSET);
+	writel(INTERLEAVE_ADDR_MAP_EN, EXYNOS4_MIU_BASE +
+		ABP_SFR_SLV_ADDRMAP_CONF_OFFSET);
+#ifdef CONFIG_MIU_LINEAR
+	writel(SLAVE0_SINGLE_ADDR_MAP_START_ADDR, EXYNOS4_MIU_BASE +
+		ABP_SFR_SLV0_SINGLE_ADDRMAP_START_OFFSET);
+	writel(SLAVE0_SINGLE_ADDR_MAP_END_ADDR, EXYNOS4_MIU_BASE +
+		ABP_SFR_SLV0_SINGLE_ADDRMAP_END_OFFSET);
+	writel(SLAVE1_SINGLE_ADDR_MAP_START_ADDR, EXYNOS4_MIU_BASE +
+		ABP_SFR_SLV1_SINGLE_ADDRMAP_START_OFFSET);
+	writel(SLAVE1_SINGLE_ADDR_MAP_END_ADDR, EXYNOS4_MIU_BASE +
+		ABP_SFR_SLV1_SINGLE_ADDRMAP_END_OFFSET);
+	writel(APB_SFR_SLV_ADDR_MAP_CONF_VAL, EXYNOS4_MIU_BASE +
+		ABP_SFR_SLV_ADDRMAP_CONF_OFFSET);
+#endif
+#endif
+	/* DREX0 */
+	dmc = (struct exynos4_dmc *)samsung_get_base_dmc_ctrl();
+	dmc_init(dmc);
+	dmc = (struct exynos4_dmc *)(samsung_get_base_dmc_ctrl()
+					+ DMC_OFFSET);
+	dmc_init(dmc);
+}
diff --git a/arch/arm/cpu/armv7/exynos/exynos4_setup.h b/arch/arm/cpu/armv7/exynos/exynos4_setup.h
new file mode 100644
index 0000000..6d25058
--- /dev/null
+++ b/arch/arm/cpu/armv7/exynos/exynos4_setup.h
@@ -0,0 +1,594 @@
+/*
+ * Machine Specific Values for EXYNOS4012 based board
+ *
+ * Copyright (C) 2011 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _ORIGEN_SETUP_H
+#define _ORIGEN_SETUP_H
+
+#include <config.h>
+#include <version.h>
+#include <asm/arch/cpu.h>
+
+#ifdef CONFIG_CLK_800_330_165
+#define DRAM_CLK_330
+#endif
+#ifdef CONFIG_CLK_1000_200_200
+#define DRAM_CLK_200
+#endif
+#ifdef CONFIG_CLK_1000_330_165
+#define DRAM_CLK_330
+#endif
+#ifdef CONFIG_CLK_1000_400_200
+#define DRAM_CLK_400
+#endif
+
+/* Bus Configuration Register Address */
+#define ASYNC_CONFIG		0x10010350
+
+/* CLK_SRC_CPU */
+#define MUX_HPM_SEL_MOUTAPLL		0x0
+#define MUX_HPM_SEL_SCLKMPLL		0x1
+#define MUX_CORE_SEL_MOUTAPLL		0x0
+#define MUX_CORE_SEL_SCLKMPLL		0x1
+#define MUX_MPLL_SEL_FILPLL		0x0
+#define MUX_MPLL_SEL_MOUTMPLLFOUT	0x1
+#define MUX_APLL_SEL_FILPLL		0x0
+#define MUX_APLL_SEL_MOUTMPLLFOUT	0x1
+#define CLK_SRC_CPU_VAL			((MUX_HPM_SEL_MOUTAPLL << 20) \
+					| (MUX_CORE_SEL_MOUTAPLL << 16) \
+					| (MUX_MPLL_SEL_MOUTMPLLFOUT << 8)\
+					| (MUX_APLL_SEL_MOUTMPLLFOUT << 0))
+
+/* CLK_DIV_CPU0 */
+#define APLL_RATIO		0x0
+#define PCLK_DBG_RATIO		0x1
+#define ATB_RATIO		0x3
+#define PERIPH_RATIO		0x3
+#define COREM1_RATIO		0x7
+#define COREM0_RATIO		0x3
+#define CORE_RATIO		0x0
+#define CLK_DIV_CPU0_VAL	((APLL_RATIO << 24) \
+				| (PCLK_DBG_RATIO << 20) \
+				| (ATB_RATIO << 16) \
+				| (PERIPH_RATIO << 12) \
+				| (COREM1_RATIO << 8) \
+				| (COREM0_RATIO << 4) \
+				| (CORE_RATIO << 0))
+
+/* CLK_DIV_CPU1 */
+#define HPM_RATIO		0x0
+#define COPY_RATIO		0x3
+#define CLK_DIV_CPU1_VAL	((HPM_RATIO << 4) | (COPY_RATIO))
+
+/* CLK_SRC_DMC */
+#define MUX_PWI_SEL_XXTI		0x0
+#define MUX_PWI_SEL_XUSBXTI		0x1
+#define MUX_PWI_SEL_SCLK_HDMI24M	0x2
+#define MUX_PWI_SEL_SCLK_USBPHY0	0x3
+#define MUX_PWI_SEL_SCLK_USBPHY1	0x4
+#define MUX_PWI_SEL_SCLK_HDMIPHY	0x5
+#define MUX_PWI_SEL_SCLKMPLL		0x6
+#define MUX_PWI_SEL_SCLKEPLL		0x7
+#define MUX_PWI_SEL_SCLKVPLL		0x8
+#define MUX_DPHY_SEL_SCLKMPLL		0x0
+#define MUX_DPHY_SEL_SCLKAPLL		0x1
+#define MUX_DMC_BUS_SEL_SCLKMPLL	0x0
+#define MUX_DMC_BUS_SEL_SCLKAPLL	0x1
+#define CLK_SRC_DMC_VAL			((MUX_PWI_SEL_XUSBXTI << 16) \
+					| (MUX_DPHY_SEL_SCLKMPLL << 8) \
+					| (MUX_DMC_BUS_SEL_SCLKMPLL << 4))
+
+/* CLK_DIV_DMC0 */
+#define CORE_TIMERS_RATIO	0x1
+#define COPY2_RATIO		0x3
+#define DMCP_RATIO		0x1
+#define DMCD_RATIO		0x1
+#define DMC_RATIO		0x1
+#define DPHY_RATIO		0x1
+#define ACP_PCLK_RATIO		0x1
+#define ACP_RATIO		0x3
+#define CLK_DIV_DMC0_VAL	((CORE_TIMERS_RATIO << 28) \
+				| (COPY2_RATIO << 24) \
+				| (DMCP_RATIO << 20) \
+				| (DMCD_RATIO << 16) \
+				| (DMC_RATIO << 12) \
+				| (DPHY_RATIO << 8) \
+				| (ACP_PCLK_RATIO << 4)	\
+				| (ACP_RATIO << 0))
+
+/* CLK_DIV_DMC1 */
+#define DPM_RATIO		0x1
+#define DVSEM_RATIO		0x1
+#define PWI_RATIO		0x1
+#define CLK_DIV_DMC1_VAL	((DPM_RATIO << 24) \
+				| (DVSEM_RATIO << 16) \
+				| (PWI_RATIO << 8))
+
+/* CLK_SRC_TOP0 */
+#define MUX_ONENAND_SEL_ACLK_133	0x0
+#define MUX_ONENAND_SEL_ACLK_160	0x1
+#define MUX_ACLK_133_SEL_SCLKMPLL	0x0
+#define MUX_ACLK_133_SEL_SCLKAPLL	0x1
+#define MUX_ACLK_160_SEL_SCLKMPLL	0x0
+#define MUX_ACLK_160_SEL_SCLKAPLL	0x1
+#define MUX_ACLK_100_SEL_SCLKMPLL	0x0
+#define MUX_ACLK_100_SEL_SCLKAPLL	0x1
+#define MUX_ACLK_200_SEL_SCLKMPLL	0x0
+#define MUX_ACLK_200_SEL_SCLKAPLL	0x1
+#define MUX_VPLL_SEL_FINPLL		0x0
+#define MUX_VPLL_SEL_FOUTVPLL		0x1
+#define MUX_EPLL_SEL_FINPLL		0x0
+#define MUX_EPLL_SEL_FOUTEPLL		0x1
+#define MUX_ONENAND_1_SEL_MOUTONENAND	0x0
+#define MUX_ONENAND_1_SEL_SCLKVPLL	0x1
+#define CLK_SRC_TOP0_VAL		((MUX_ONENAND_SEL_ACLK_133 << 28) \
+					| (MUX_ACLK_133_SEL_SCLKMPLL << 24) \
+					| (MUX_ACLK_160_SEL_SCLKMPLL << 20) \
+					| (MUX_ACLK_100_SEL_SCLKMPLL << 16) \
+					| (MUX_ACLK_200_SEL_SCLKMPLL << 12) \
+					| (MUX_VPLL_SEL_FINPLL << 8) \
+					| (MUX_EPLL_SEL_FINPLL << 4)\
+					| (MUX_ONENAND_1_SEL_MOUTONENAND << 0))
+
+/* CLK_SRC_TOP1 */
+#define VPLLSRC_SEL_FINPLL	0x0
+#define VPLLSRC_SEL_SCLKHDMI24M	0x1
+#define CLK_SRC_TOP1_VAL	(VPLLSRC_SEL_FINPLL)
+
+/* CLK_DIV_TOP */
+#define ONENAND_RATIO		0x0
+#define ACLK_133_RATIO		0x5
+#define ACLK_160_RATIO		0x4
+#define ACLK_100_RATIO		0x7
+#define ACLK_200_RATIO		0x3
+#define CLK_DIV_TOP_VAL		((ONENAND_RATIO << 16)	\
+				| (ACLK_133_RATIO << 12)\
+				| (ACLK_160_RATIO << 8)	\
+				| (ACLK_100_RATIO << 4)	\
+				| (ACLK_200_RATIO << 0))
+
+/* CLK_SRC_LEFTBUS */
+#define MUX_GDL_SEL_SCLKMPLL	0x0
+#define MUX_GDL_SEL_SCLKAPLL	0x1
+#define CLK_SRC_LEFTBUS_VAL	(MUX_GDL_SEL_SCLKMPLL)
+
+/* CLK_DIV_LEFTBUS */
+#define GPL_RATIO		0x1
+#define GDL_RATIO		0x3
+#define CLK_DIV_LEFTBUS_VAL	((GPL_RATIO << 4) | (GDL_RATIO))
+
+/* CLK_SRC_RIGHTBUS */
+#define MUX_GDR_SEL_SCLKMPLL	0x0
+#define MUX_GDR_SEL_SCLKAPLL	0x1
+#define CLK_SRC_RIGHTBUS_VAL	(MUX_GDR_SEL_SCLKMPLL)
+
+/* CLK_DIV_RIGHTBUS */
+#define GPR_RATIO		0x1
+#define GDR_RATIO		0x3
+#define CLK_DIV_RIGHTBUS_VAL	((GPR_RATIO << 4) | (GDR_RATIO))
+
+/* CLK_SRS_FSYS: 6 = SCLKMPLL */
+#define SATA_SEL_SCLKMPLL	0
+#define SATA_SEL_SCLKAPLL	1
+
+#define MMC_SEL_XXTI		0
+#define MMC_SEL_XUSBXTI		1
+#define MMC_SEL_SCLK_HDMI24M	2
+#define MMC_SEL_SCLK_USBPHY0	3
+#define MMC_SEL_SCLK_USBPHY1	4
+#define MMC_SEL_SCLK_HDMIPHY	5
+#define MMC_SEL_SCLKMPLL	6
+#define MMC_SEL_SCLKEPLL	7
+#define MMC_SEL_SCLKVPLL	8
+
+#define MMCC0_SEL		MMC_SEL_SCLKMPLL
+#define MMCC1_SEL		MMC_SEL_SCLKMPLL
+#define MMCC2_SEL		MMC_SEL_SCLKMPLL
+#define MMCC3_SEL		MMC_SEL_SCLKMPLL
+#define MMCC4_SEL		MMC_SEL_SCLKMPLL
+#define CLK_SRC_FSYS_VAL	((SATA_SEL_SCLKMPLL << 24) \
+				| (MMCC4_SEL << 16) \
+				| (MMCC3_SEL << 12) \
+				| (MMCC2_SEL << 8) \
+				| (MMCC1_SEL << 4) \
+				| (MMCC0_SEL << 0))
+
+/* SCLK_MMC[0-4] = MOUTMMC[0-4]/(MMC[0-4]_RATIO + 1)/(MMC[0-4]_PRE_RATIO +1) */
+/* CLK_DIV_FSYS1 */
+#define MMC0_RATIO		0xF
+#define MMC0_PRE_RATIO		0x0
+#define MMC1_RATIO		0xF
+#define MMC1_PRE_RATIO		0x0
+#define CLK_DIV_FSYS1_VAL	((MMC1_PRE_RATIO << 24) \
+				| (MMC1_RATIO << 16) \
+				| (MMC0_PRE_RATIO << 8) \
+				| (MMC0_RATIO << 0))
+
+/* CLK_DIV_FSYS2 */
+#define MMC2_RATIO		0xF
+#define MMC2_PRE_RATIO		0x0
+#define MMC3_RATIO		0xF
+#define MMC3_PRE_RATIO		0x0
+#define CLK_DIV_FSYS2_VAL	((MMC3_PRE_RATIO << 24) \
+				| (MMC3_RATIO << 16) \
+				| (MMC2_PRE_RATIO << 8) \
+				| (MMC2_RATIO << 0))
+
+/* CLK_DIV_FSYS3 */
+#define MMC4_RATIO		0xF
+#define MMC4_PRE_RATIO		0x0
+#define CLK_DIV_FSYS3_VAL	((MMC4_PRE_RATIO << 8) \
+				| (MMC4_RATIO << 0))
+
+/* CLK_SRC_PERIL0 */
+#define UART_SEL_XXTI		0
+#define UART_SEL_XUSBXTI	1
+#define UART_SEL_SCLK_HDMI24M	2
+#define UART_SEL_SCLK_USBPHY0	3
+#define UART_SEL_SCLK_USBPHY1	4
+#define UART_SEL_SCLK_HDMIPHY	5
+#define UART_SEL_SCLKMPLL	6
+#define UART_SEL_SCLKEPLL	7
+#define UART_SEL_SCLKVPLL	8
+
+#define UART0_SEL		UART_SEL_SCLKMPLL
+#define UART1_SEL		UART_SEL_SCLKMPLL
+#define UART2_SEL		UART_SEL_SCLKMPLL
+#define UART3_SEL		UART_SEL_SCLKMPLL
+#define UART4_SEL		UART_SEL_SCLKMPLL
+#define CLK_SRC_PERIL0_VAL	((UART4_SEL << 16) \
+				| (UART3_SEL << 12) \
+				| (UART2_SEL << 8) \
+				| (UART1_SEL << 4) \
+				| (UART0_SEL << 0))
+
+/* SCLK_UART[0-4] = MOUTUART[0-4]/(UART[0-4]_RATIO + 1) */
+/* CLK_DIV_PERIL0 */
+#define UART0_RATIO		7
+#define UART1_RATIO		7
+#define UART2_RATIO		7
+#define UART3_RATIO		7
+#define UART4_RATIO		7
+#define CLK_DIV_PERIL0_VAL	((UART4_RATIO << 16) \
+				| (UART3_RATIO << 12) \
+				| (UART2_RATIO << 8) \
+				| (UART1_RATIO << 4) \
+				| (UART0_RATIO << 0))
+
+/* Clock Source CAM/FIMC */
+/* CLK_SRC_CAM */
+#define CAM0_SEL_XUSBXTI	1
+#define CAM1_SEL_XUSBXTI	1
+#define CSIS0_SEL_XUSBXTI	1
+#define CSIS1_SEL_XUSBXTI	1
+
+#define FIMC_SEL_SCLKMPLL	6
+#define FIMC0_LCLK_SEL		FIMC_SEL_SCLKMPLL
+#define FIMC1_LCLK_SEL		FIMC_SEL_SCLKMPLL
+#define FIMC2_LCLK_SEL		FIMC_SEL_SCLKMPLL
+#define FIMC3_LCLK_SEL		FIMC_SEL_SCLKMPLL
+
+#define CLK_SRC_CAM_VAL		((CSIS1_SEL_XUSBXTI << 28) \
+				| (CSIS0_SEL_XUSBXTI << 24) \
+				| (CAM1_SEL_XUSBXTI << 20) \
+				| (CAM0_SEL_XUSBXTI << 16) \
+				| (FIMC3_LCLK_SEL << 12) \
+				| (FIMC2_LCLK_SEL << 8) \
+				| (FIMC1_LCLK_SEL << 4) \
+				| (FIMC0_LCLK_SEL << 0))
+
+/* SCLK CAM */
+/* CLK_DIV_CAM */
+#define FIMC0_LCLK_RATIO	4
+#define FIMC1_LCLK_RATIO	4
+#define FIMC2_LCLK_RATIO	4
+#define FIMC3_LCLK_RATIO	4
+#define CLK_DIV_CAM_VAL		((FIMC3_LCLK_RATIO << 12) \
+				| (FIMC2_LCLK_RATIO << 8) \
+				| (FIMC1_LCLK_RATIO << 4) \
+				| (FIMC0_LCLK_RATIO << 0))
+
+/* SCLK MFC */
+/* CLK_SRC_MFC */
+#define MFC_SEL_MPLL		0
+#define MOUTMFC_0		0
+#define MFC_SEL			MOUTMFC_0
+#define MFC_0_SEL		MFC_SEL_MPLL
+#define CLK_SRC_MFC_VAL		((MFC_SEL << 8) | (MFC_0_SEL))
+
+
+/* CLK_DIV_MFC */
+#define MFC_RATIO		3
+#define CLK_DIV_MFC_VAL		(MFC_RATIO)
+
+/* SCLK G3D */
+/* CLK_SRC_G3D */
+#define G3D_SEL_MPLL		0
+#define MOUTG3D_0		0
+#define G3D_SEL			MOUTG3D_0
+#define G3D_0_SEL		G3D_SEL_MPLL
+#define CLK_SRC_G3D_VAL		((G3D_SEL << 8) | (G3D_0_SEL))
+
+/* CLK_DIV_G3D */
+#define G3D_RATIO		1
+#define CLK_DIV_G3D_VAL		(G3D_RATIO)
+
+/* SCLK LCD0 */
+/* CLK_SRC_LCD0 */
+#define FIMD_SEL_SCLKMPLL	6
+#define MDNIE0_SEL_XUSBXTI	1
+#define MDNIE_PWM0_SEL_XUSBXTI	1
+#define MIPI0_SEL_XUSBXTI	1
+#define CLK_SRC_LCD0_VAL	((MIPI0_SEL_XUSBXTI << 12) \
+				| (MDNIE_PWM0_SEL_XUSBXTI << 8) \
+				| (MDNIE0_SEL_XUSBXTI << 4) \
+				| (FIMD_SEL_SCLKMPLL << 0))
+
+/* CLK_DIV_LCD0 */
+#define FIMD0_RATIO		4
+#define CLK_DIV_LCD0_VAL	(FIMD0_RATIO)
+
+/* Required period to generate a stable clock output */
+/* PLL_LOCK_TIME */
+#define PLL_LOCKTIME		0x1C20
+
+/* PLL Values */
+#define DISABLE			0
+#define ENABLE			1
+#define SET_PLL(mdiv, pdiv, sdiv)	((ENABLE << 31)\
+					| (mdiv << 16) \
+					| (pdiv << 8) \
+					| (sdiv << 0))
+
+/* APLL_CON0 */
+#define APLL_MDIV		0xFA
+#define APLL_PDIV		0x6
+#define APLL_SDIV		0x1
+#define APLL_CON0_VAL		SET_PLL(APLL_MDIV, APLL_PDIV, APLL_SDIV)
+
+/* APLL_CON1 */
+#define APLL_AFC_ENB		0x1
+#define APLL_AFC		0xC
+#define APLL_CON1_VAL		((APLL_AFC_ENB << 31) | (APLL_AFC << 0))
+
+/* MPLL_CON0 */
+#define MPLL_MDIV		0xC8
+#define MPLL_PDIV		0x6
+#define MPLL_SDIV		0x1
+#define MPLL_CON0_VAL		SET_PLL(MPLL_MDIV, MPLL_PDIV, MPLL_SDIV)
+
+/* MPLL_CON1 */
+#define MPLL_AFC_ENB		0x0
+#define MPLL_AFC		0x1C
+#define MPLL_CON1_VAL		((MPLL_AFC_ENB << 31) | (MPLL_AFC << 0))
+
+/* EPLL_CON0 */
+#define EPLL_MDIV		0x30
+#define EPLL_PDIV		0x3
+#define EPLL_SDIV		0x2
+#define EPLL_CON0_VAL		SET_PLL(EPLL_MDIV, EPLL_PDIV, EPLL_SDIV)
+
+/* EPLL_CON1 */
+#define EPLL_K			0x0
+#define EPLL_CON1_VAL		(EPLL_K >> 0)
+
+/* VPLL_CON0 */
+#define VPLL_MDIV		0x35
+#define VPLL_PDIV		0x3
+#define VPLL_SDIV		0x2
+#define VPLL_CON0_VAL		SET_PLL(VPLL_MDIV, VPLL_PDIV, VPLL_SDIV)
+
+/* VPLL_CON1 */
+#define VPLL_SSCG_EN		DISABLE
+#define VPLL_SEL_PF_DN_SPREAD	0x0
+#define VPLL_MRR		0x11
+#define VPLL_MFR		0x0
+#define VPLL_K			0x400
+#define VPLL_CON1_VAL		((VPLL_SSCG_EN << 31)\
+				| (VPLL_SEL_PF_DN_SPREAD << 29) \
+				| (VPLL_MRR << 24) \
+				| (VPLL_MFR << 16) \
+				| (VPLL_K << 0))
+
+/* DMC */
+#define DIRECT_CMD_NOP	0x07000000
+#define DIRECT_CMD_ZQ	0x0a000000
+#define DIRECT_CMD_CHIP1_SHIFT	(1 << 20)
+#define MEM_TIMINGS_MSR_COUNT	4
+#define CTRL_START	(1 << 0)
+#define CTRL_DLL_ON	(1 << 1)
+#define AREF_EN		(1 << 5)
+#define DRV_TYPE	(1 << 6)
+
+struct mem_timings {
+	unsigned direct_cmd_msr[MEM_TIMINGS_MSR_COUNT];
+	unsigned timingref;
+	unsigned timingrow;
+	unsigned timingdata;
+	unsigned timingpower;
+	unsigned zqcontrol;
+	unsigned control0;
+	unsigned control1;
+	unsigned control2;
+	unsigned concontrol;
+	unsigned prechconfig;
+	unsigned memcontrol;
+	unsigned memconfig0;
+	unsigned memconfig1;
+	unsigned dll_resync;
+	unsigned dll_on;
+};
+
+/* MIU */
+/* MIU Config Register Offsets*/
+#define APB_SFR_INTERLEAVE_CONF_OFFSET	0x400
+#define APB_SFR_ARBRITATION_CONF_OFFSET	0xC00
+#define ABP_SFR_SLV_ADDRMAP_CONF_OFFSET	0x800
+#define ABP_SFR_INTERLEAVE_ADDRMAP_START_OFFSET	0x808
+#define ABP_SFR_INTERLEAVE_ADDRMAP_END_OFFSET	0x810
+#define ABP_SFR_SLV0_SINGLE_ADDRMAP_START_OFFSET	0x818
+#define ABP_SFR_SLV0_SINGLE_ADDRMAP_END_OFFSET	0x820
+#define ABP_SFR_SLV1_SINGLE_ADDRMAP_START_OFFSET	0x828
+#define ABP_SFR_SLV1_SINGLE_ADDRMAP_END_OFFSET	0x830
+
+#ifdef CONFIG_ORIGEN
+/* Interleave: 2Bit, Interleave_bit1: 0x15, Interleave_bit0: 0x7 */
+#define APB_SFR_INTERLEAVE_CONF_VAL	0x20001507
+#define APB_SFR_ARBRITATION_CONF_VAL	0x00000001
+#endif
+
+#define INTERLEAVE_ADDR_MAP_START_ADDR	0x40000000
+#define INTERLEAVE_ADDR_MAP_END_ADDR	0xbfffffff
+#define INTERLEAVE_ADDR_MAP_EN		0x00000001
+
+#ifdef CONFIG_MIU_1BIT_INTERLEAVED
+/* Interleave_bit0: 0xC*/
+#define APB_SFR_INTERLEAVE_CONF_VAL	0x0000000c
+#endif
+#ifdef CONFIG_MIU_2BIT_INTERLEAVED
+/* Interleave: 2Bit, Interleave_bit1: 0x15, Interleave_bit0: 0xc */
+#define APB_SFR_INTERLEAVE_CONF_VAL	0x2000150c
+#endif
+#define SLAVE0_SINGLE_ADDR_MAP_START_ADDR	0x40000000
+#define SLAVE0_SINGLE_ADDR_MAP_END_ADDR		0x7fffffff
+#define SLAVE1_SINGLE_ADDR_MAP_START_ADDR	0x80000000
+#define SLAVE1_SINGLE_ADDR_MAP_END_ADDR		0xbfffffff
+/* Enable SME0 and SME1*/
+#define APB_SFR_SLV_ADDR_MAP_CONF_VAL		0x00000006
+
+#define FORCE_DLL_RESYNC	3
+#define DLL_CONTROL_ON		1
+
+#define DIRECT_CMD1	0x00020000
+#define DIRECT_CMD2	0x00030000
+#define DIRECT_CMD3	0x00010002
+#define DIRECT_CMD4	0x00000328
+
+#define CTRL_ZQ_MODE_NOTERM	(0x1 << 0)
+#define CTRL_ZQ_START		(0x1 << 1)
+#define CTRL_ZQ_DIV		(0 << 4)
+#define CTRL_ZQ_MODE_DDS	(0x7 << 8)
+#define CTRL_ZQ_MODE_TERM	(0x2 << 11)
+#define CTRL_ZQ_FORCE_IMPN	(0x5 << 14)
+#define CTRL_ZQ_FORCE_IMPP	(0x6 << 17)
+#define CTRL_DCC		(0xE38 << 20)
+#define ZQ_CONTROL_VAL		(CTRL_ZQ_MODE_NOTERM | CTRL_ZQ_START\
+				| CTRL_ZQ_DIV | CTRL_ZQ_MODE_DDS\
+				| CTRL_ZQ_MODE_TERM | CTRL_ZQ_FORCE_IMPN\
+				| CTRL_ZQ_FORCE_IMPP | CTRL_DCC)
+
+#define ASYNC			(0 << 0)
+#define CLK_RATIO		(1 << 1)
+#define DIV_PIPE		(1 << 3)
+#define AWR_ON			(1 << 4)
+#define AREF_DISABLE		(0 << 5)
+#define DRV_TYPE_DISABLE	(0 << 6)
+#define CHIP0_NOT_EMPTY		(0 << 8)
+#define CHIP1_NOT_EMPTY		(0 << 9)
+#define DQ_SWAP_DISABLE		(0 << 10)
+#define QOS_FAST_DISABLE	(0 << 11)
+#define RD_FETCH		(0x3 << 12)
+#define TIMEOUT_LEVEL0		(0xFFF << 16)
+#define CONCONTROL_VAL		(ASYNC | CLK_RATIO | DIV_PIPE | AWR_ON\
+				| AREF_DISABLE | DRV_TYPE_DISABLE\
+				| CHIP0_NOT_EMPTY | CHIP1_NOT_EMPTY\
+				| DQ_SWAP_DISABLE | QOS_FAST_DISABLE\
+				| RD_FETCH | TIMEOUT_LEVEL0)
+
+#define CLK_STOP_DISABLE	(0 << 1)
+#define DPWRDN_DISABLE		(0 << 2)
+#define DPWRDN_TYPE		(0 << 3)
+#define TP_DISABLE		(0 << 4)
+#define DSREF_DIABLE		(0 << 5)
+#define ADD_LAT_PALL		(1 << 6)
+#define MEM_TYPE_DDR3		(0x6 << 8)
+#define MEM_WIDTH_32		(0x2 << 12)
+#define NUM_CHIP_2		(1 << 16)
+#define BL_8			(0x3 << 20)
+#define MEMCONTROL_VAL		(CLK_STOP_DISABLE | DPWRDN_DISABLE\
+				| DPWRDN_TYPE | TP_DISABLE | DSREF_DIABLE\
+				| ADD_LAT_PALL | MEM_TYPE_DDR3 | MEM_WIDTH_32\
+				| NUM_CHIP_2 | BL_8)
+
+
+#define CHIP_BANK_8		(0x3 << 0)
+#define CHIP_ROW_14		(0x2 << 4)
+#define CHIP_COL_10		(0x3 << 8)
+#define CHIP_MAP_INTERLEAVED	(1 << 12)
+#define CHIP_MASK		(0xe0 << 16)
+#ifdef CONFIG_MIU_LINEAR
+#define CHIP0_BASE		(0x40 << 24)
+#define CHIP1_BASE		(0x60 << 24)
+#else
+#define CHIP0_BASE		(0x20 << 24)
+#define CHIP1_BASE		(0x40 << 24)
+#endif
+#define MEMCONFIG0_VAL		(CHIP_BANK_8 | CHIP_ROW_14 | CHIP_COL_10\
+				| CHIP_MAP_INTERLEAVED | CHIP_MASK | CHIP0_BASE)
+#define MEMCONFIG1_VAL		(CHIP_BANK_8 | CHIP_ROW_14 | CHIP_COL_10\
+				| CHIP_MAP_INTERLEAVED | CHIP_MASK | CHIP1_BASE)
+
+#define TP_CNT			(0xff << 24)
+#define PRECHCONFIG		TP_CNT
+
+#define CTRL_OFF		(0 << 0)
+#define CTRL_DLL_OFF		(0 << 1)
+#define CTRL_HALF		(0 << 2)
+#define CTRL_DFDQS		(1 << 3)
+#define DQS_DELAY		(0 << 4)
+#define CTRL_START_POINT	(0x10 << 8)
+#define CTRL_INC		(0x10 << 16)
+#define CTRL_FORCE		(0x71 << 24)
+#define CONTROL0_VAL		(CTRL_OFF | CTRL_DLL_OFF | CTRL_HALF\
+				| CTRL_DFDQS | DQS_DELAY | CTRL_START_POINT\
+				| CTRL_INC | CTRL_FORCE)
+
+#define CTRL_SHIFTC		(0x6 << 0)
+#define CTRL_REF		(8 << 4)
+#define CTRL_SHGATE		(1 << 29)
+#define TERM_READ_EN		(1 << 30)
+#define TERM_WRITE_EN		(1 << 31)
+#define CONTROL1_VAL		(CTRL_SHIFTC | CTRL_REF | CTRL_SHGATE\
+				| TERM_READ_EN | TERM_WRITE_EN)
+
+#define CONTROL2_VAL		0x00000000
+
+#ifdef CONFIG_ORIGEN
+#define TIMINGREF_VAL		0x000000BB
+#define TIMINGROW_VAL		0x4046654f
+#define	TIMINGDATA_VAL		0x46400506
+#define	TIMINGPOWER_VAL		0x52000A3C
+#else
+#define TIMINGREF_VAL		0x000000BC
+#ifdef DRAM_CLK_330
+#define TIMINGROW_VAL		0x3545548d
+#define	TIMINGDATA_VAL		0x45430506
+#define	TIMINGPOWER_VAL		0x4439033c
+#endif
+#ifdef DRAM_CLK_400
+#define TIMINGROW_VAL		0x45430506
+#define	TIMINGDATA_VAL		0x56500506
+#define	TIMINGPOWER_VAL		0x5444033d
+#endif
+#endif
+#endif
diff --git a/arch/arm/cpu/armv7/exynos/exynos5_setup.h b/arch/arm/cpu/armv7/exynos/exynos5_setup.h
new file mode 100644
index 0000000..8f36c16
--- /dev/null
+++ b/arch/arm/cpu/armv7/exynos/exynos5_setup.h
@@ -0,0 +1,567 @@
+/*
+ * Machine Specific Values for SMDK5250 board based on EXYNOS5
+ *
+ * Copyright (C) 2012 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _SMDK5250_SETUP_H
+#define _SMDK5250_SETUP_H
+
+#include <config.h>
+#include <asm/arch/dmc.h>
+
+/* APLL_CON1	*/
+#define APLL_CON1_VAL	(0x00203800)
+
+/* MPLL_CON1	*/
+#define MPLL_CON1_VAL   (0x00203800)
+
+/* CPLL_CON1	*/
+#define CPLL_CON1_VAL	(0x00203800)
+
+/* GPLL_CON1	*/
+#define GPLL_CON1_VAL	(0x00203800)
+
+/* EPLL_CON1, CON2	*/
+#define EPLL_CON1_VAL	0x00000000
+#define EPLL_CON2_VAL	0x00000080
+
+/* VPLL_CON1, CON2	*/
+#define VPLL_CON1_VAL	0x00000000
+#define VPLL_CON2_VAL	0x00000080
+
+/* BPLL_CON1	*/
+#define BPLL_CON1_VAL	0x00203800
+
+/* Set PLL */
+#define set_pll(mdiv, pdiv, sdiv)	(1<<31 | mdiv<<16 | pdiv<<8 | sdiv)
+
+/* CLK_SRC_CPU	*/
+/* 0 = MOUTAPLL,  1 = SCLKMPLL	*/
+#define MUX_HPM_SEL             0
+#define MUX_CPU_SEL             0
+#define MUX_APLL_SEL            1
+
+#define CLK_SRC_CPU_VAL		((MUX_HPM_SEL << 20)    \
+				| (MUX_CPU_SEL << 16)  \
+				| (MUX_APLL_SEL))
+
+/* MEMCONTROL register bit fields */
+#define DMC_MEMCONTROL_CLK_STOP_DISABLE	(0 << 0)
+#define DMC_MEMCONTROL_DPWRDN_DISABLE	(0 << 1)
+#define DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE	(0 << 2)
+#define DMC_MEMCONTROL_TP_DISABLE	(0 << 4)
+#define DMC_MEMCONTROL_DSREF_DISABLE	(0 << 5)
+#define DMC_MEMCONTROL_DSREF_ENABLE	(1 << 5)
+#define DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(x)    (x << 6)
+
+#define DMC_MEMCONTROL_MEM_TYPE_LPDDR3  (7 << 8)
+#define DMC_MEMCONTROL_MEM_TYPE_DDR3    (6 << 8)
+#define DMC_MEMCONTROL_MEM_TYPE_LPDDR2  (5 << 8)
+
+#define DMC_MEMCONTROL_MEM_WIDTH_32BIT  (2 << 12)
+
+#define DMC_MEMCONTROL_NUM_CHIP_1       (0 << 16)
+#define DMC_MEMCONTROL_NUM_CHIP_2       (1 << 16)
+
+#define DMC_MEMCONTROL_BL_8             (3 << 20)
+#define DMC_MEMCONTROL_BL_4             (2 << 20)
+
+#define DMC_MEMCONTROL_PZQ_DISABLE      (0 << 24)
+
+#define DMC_MEMCONTROL_MRR_BYTE_7_0     (0 << 25)
+#define DMC_MEMCONTROL_MRR_BYTE_15_8    (1 << 25)
+#define DMC_MEMCONTROL_MRR_BYTE_23_16   (2 << 25)
+#define DMC_MEMCONTROL_MRR_BYTE_31_24   (3 << 25)
+
+/* MEMCONFIG0 register bit fields */
+#define DMC_MEMCONFIGX_CHIP_MAP_INTERLEAVED     (1 << 12)
+#define DMC_MEMCONFIGX_CHIP_COL_10              (3 << 8)
+#define DMC_MEMCONFIGX_CHIP_ROW_14              (2 << 4)
+#define DMC_MEMCONFIGX_CHIP_ROW_15              (3 << 4)
+#define DMC_MEMCONFIGX_CHIP_BANK_8              (3 << 0)
+
+#define DMC_MEMBASECONFIGX_CHIP_BASE(x)         (x << 16)
+#define DMC_MEMBASECONFIGX_CHIP_MASK(x)         (x << 0)
+#define DMC_MEMBASECONFIG_VAL(x)        (       \
+	DMC_MEMBASECONFIGX_CHIP_BASE(x) |       \
+	DMC_MEMBASECONFIGX_CHIP_MASK(0x780)     \
+)
+
+#define DMC_MEMBASECONFIG0_VAL  DMC_MEMBASECONFIG_VAL(0x40)
+#define DMC_MEMBASECONFIG1_VAL  DMC_MEMBASECONFIG_VAL(0x80)
+
+#define DMC_PRECHCONFIG_VAL             0xFF000000
+#define DMC_PWRDNCONFIG_VAL             0xFFFF00FF
+
+#define DMC_CONCONTROL_RESET_VAL	0x0FFF0000
+#define DFI_INIT_START		(1 << 28)
+#define EMPTY			(1 << 8)
+#define AREF_EN			(1 << 5)
+
+#define DFI_INIT_COMPLETE_CHO	(1 << 2)
+#define DFI_INIT_COMPLETE_CH1	(1 << 3)
+
+#define RDLVL_COMPLETE_CHO	(1 << 14)
+#define RDLVL_COMPLETE_CH1	(1 << 15)
+
+#define CLK_STOP_EN	(1 << 0)
+#define DPWRDN_EN	(1 << 1)
+#define DSREF_EN	(1 << 5)
+
+/* COJCONTROL register bit fields */
+#define DMC_CONCONTROL_IO_PD_CON_DISABLE	(0 << 3)
+#define DMC_CONCONTROL_AREF_EN_DISABLE		(0 << 5)
+#define DMC_CONCONTROL_EMPTY_DISABLE		(0 << 8)
+#define DMC_CONCONTROL_EMPTY_ENABLE		(1 << 8)
+#define DMC_CONCONTROL_RD_FETCH_DISABLE		(0x0 << 12)
+#define DMC_CONCONTROL_TIMEOUT_LEVEL0		(0xFFF << 16)
+#define DMC_CONCONTROL_DFI_INIT_START_DISABLE	(0 << 28)
+
+/* CLK_DIV_CPU0_VAL */
+#define CLK_DIV_CPU0_VAL	((ARM2_RATIO << 28)             \
+				| (APLL_RATIO << 24)            \
+				| (PCLK_DBG_RATIO << 20)        \
+				| (ATB_RATIO << 16)             \
+				| (PERIPH_RATIO << 12)          \
+				| (ACP_RATIO << 8)              \
+				| (CPUD_RATIO << 4)             \
+				| (ARM_RATIO))
+
+
+/* CLK_FSYS */
+#define CLK_SRC_FSYS0_VAL              0x66666
+#define CLK_DIV_FSYS0_VAL	       0x0BB00000
+
+/* CLK_DIV_CPU1	*/
+#define HPM_RATIO               0x2
+#define COPY_RATIO              0x0
+
+/* CLK_DIV_CPU1 = 0x00000003 */
+#define CLK_DIV_CPU1_VAL        ((HPM_RATIO << 4)		\
+				| (COPY_RATIO))
+
+/* CLK_SRC_CORE0 */
+#define CLK_SRC_CORE0_VAL       0x00000000
+
+/* CLK_SRC_CORE1 */
+#define CLK_SRC_CORE1_VAL       0x100
+
+/* CLK_DIV_CORE0 */
+#define CLK_DIV_CORE0_VAL       0x00120000
+
+/* CLK_DIV_CORE1 */
+#define CLK_DIV_CORE1_VAL       0x07070700
+
+/* CLK_DIV_SYSRGT */
+#define CLK_DIV_SYSRGT_VAL      0x00000111
+
+/* CLK_DIV_ACP */
+#define CLK_DIV_ACP_VAL         0x12
+
+/* CLK_DIV_SYSLFT */
+#define CLK_DIV_SYSLFT_VAL      0x00000311
+
+/* CLK_SRC_CDREX */
+#define CLK_SRC_CDREX_VAL       0x1
+
+/* CLK_DIV_CDREX */
+#define MCLK_CDREX2_RATIO       0x0
+#define ACLK_EFCON_RATIO        0x1
+#define MCLK_DPHY_RATIO		0x1
+#define MCLK_CDREX_RATIO	0x1
+#define ACLK_C2C_200_RATIO	0x1
+#define C2C_CLK_400_RATIO	0x1
+#define PCLK_CDREX_RATIO	0x1
+#define ACLK_CDREX_RATIO	0x1
+
+#define CLK_DIV_CDREX_VAL	((MCLK_DPHY_RATIO << 24)        \
+				| (C2C_CLK_400_RATIO << 6)	\
+				| (PCLK_CDREX_RATIO << 4)	\
+				| (ACLK_CDREX_RATIO))
+
+/* CLK_SRC_TOP0	*/
+#define MUX_ACLK_300_GSCL_SEL           0x0
+#define MUX_ACLK_300_GSCL_MID_SEL       0x0
+#define MUX_ACLK_400_G3D_MID_SEL        0x0
+#define MUX_ACLK_333_SEL	        0x0
+#define MUX_ACLK_300_DISP1_SEL	        0x0
+#define MUX_ACLK_300_DISP1_MID_SEL      0x0
+#define MUX_ACLK_200_SEL	        0x0
+#define MUX_ACLK_166_SEL	        0x0
+#define CLK_SRC_TOP0_VAL	((MUX_ACLK_300_GSCL_SEL  << 25)		\
+				| (MUX_ACLK_300_GSCL_MID_SEL << 24)	\
+				| (MUX_ACLK_400_G3D_MID_SEL << 20)	\
+				| (MUX_ACLK_333_SEL << 16)		\
+				| (MUX_ACLK_300_DISP1_SEL << 15)	\
+				| (MUX_ACLK_300_DISP1_MID_SEL << 14)	\
+				| (MUX_ACLK_200_SEL << 12)		\
+				| (MUX_ACLK_166_SEL << 8))
+
+/* CLK_SRC_TOP1	*/
+#define MUX_ACLK_400_G3D_SEL            0x1
+#define MUX_ACLK_400_ISP_SEL            0x0
+#define MUX_ACLK_400_IOP_SEL            0x0
+#define MUX_ACLK_MIPI_HSI_TXBASE_SEL    0x0
+#define MUX_ACLK_300_GSCL_MID1_SEL      0x0
+#define MUX_ACLK_300_DISP1_MID1_SEL     0x0
+#define CLK_SRC_TOP1_VAL	((MUX_ACLK_400_G3D_SEL << 28)           \
+				|(MUX_ACLK_400_ISP_SEL << 24)           \
+				|(MUX_ACLK_400_IOP_SEL << 20)           \
+				|(MUX_ACLK_MIPI_HSI_TXBASE_SEL << 16)   \
+				|(MUX_ACLK_300_GSCL_MID1_SEL << 12)     \
+				|(MUX_ACLK_300_DISP1_MID1_SEL << 8))
+
+/* CLK_SRC_TOP2 */
+#define MUX_GPLL_SEL                    0x1
+#define MUX_BPLL_USER_SEL               0x0
+#define MUX_MPLL_USER_SEL               0x0
+#define MUX_VPLL_SEL                    0x1
+#define MUX_EPLL_SEL                    0x1
+#define MUX_CPLL_SEL                    0x1
+#define VPLLSRC_SEL                     0x0
+#define CLK_SRC_TOP2_VAL	((MUX_GPLL_SEL << 28)		\
+				| (MUX_BPLL_USER_SEL << 24)	\
+				| (MUX_MPLL_USER_SEL << 20)	\
+				| (MUX_VPLL_SEL << 16)	        \
+				| (MUX_EPLL_SEL << 12)	        \
+				| (MUX_CPLL_SEL << 8)           \
+				| (VPLLSRC_SEL))
+/* CLK_SRC_TOP3 */
+#define MUX_ACLK_333_SUB_SEL            0x1
+#define MUX_ACLK_400_SUB_SEL            0x1
+#define MUX_ACLK_266_ISP_SUB_SEL        0x1
+#define MUX_ACLK_266_GPS_SUB_SEL        0x0
+#define MUX_ACLK_300_GSCL_SUB_SEL       0x1
+#define MUX_ACLK_266_GSCL_SUB_SEL       0x1
+#define MUX_ACLK_300_DISP1_SUB_SEL      0x1
+#define MUX_ACLK_200_DISP1_SUB_SEL      0x1
+#define CLK_SRC_TOP3_VAL	((MUX_ACLK_333_SUB_SEL << 24)	        \
+				| (MUX_ACLK_400_SUB_SEL << 20)	        \
+				| (MUX_ACLK_266_ISP_SUB_SEL << 16)	\
+				| (MUX_ACLK_266_GPS_SUB_SEL << 12)      \
+				| (MUX_ACLK_300_GSCL_SUB_SEL << 10)     \
+				| (MUX_ACLK_266_GSCL_SUB_SEL << 8)      \
+				| (MUX_ACLK_300_DISP1_SUB_SEL << 6)     \
+				| (MUX_ACLK_200_DISP1_SUB_SEL << 4))
+
+/* CLK_DIV_TOP0	*/
+#define ACLK_300_DISP1_RATIO	0x2
+#define ACLK_400_G3D_RATIO	0x0
+#define ACLK_333_RATIO		0x0
+#define ACLK_266_RATIO		0x2
+#define ACLK_200_RATIO		0x3
+#define ACLK_166_RATIO		0x1
+#define ACLK_133_RATIO		0x1
+#define ACLK_66_RATIO		0x5
+
+#define CLK_DIV_TOP0_VAL	((ACLK_300_DISP1_RATIO << 28)	\
+				| (ACLK_400_G3D_RATIO << 24)	\
+				| (ACLK_333_RATIO  << 20)	\
+				| (ACLK_266_RATIO << 16)	\
+				| (ACLK_200_RATIO << 12)	\
+				| (ACLK_166_RATIO << 8)		\
+				| (ACLK_133_RATIO << 4)		\
+				| (ACLK_66_RATIO))
+
+/* CLK_DIV_TOP1	*/
+#define ACLK_MIPI_HSI_TX_BASE_RATIO     0x3
+#define ACLK_66_PRE_RATIO               0x1
+#define ACLK_400_ISP_RATIO              0x1
+#define ACLK_400_IOP_RATIO              0x1
+#define ACLK_300_GSCL_RATIO             0x2
+
+#define CLK_DIV_TOP1_VAL	((ACLK_MIPI_HSI_TX_BASE_RATIO << 28)	\
+				| (ACLK_66_PRE_RATIO << 24)		\
+				| (ACLK_400_ISP_RATIO  << 20)		\
+				| (ACLK_400_IOP_RATIO << 16)		\
+				| (ACLK_300_GSCL_RATIO << 12))
+
+/* APLL_LOCK	*/
+#define APLL_LOCK_VAL	(0x546)
+/* MPLL_LOCK	*/
+#define MPLL_LOCK_VAL	(0x546)
+/* CPLL_LOCK	*/
+#define CPLL_LOCK_VAL	(0x546)
+/* GPLL_LOCK	*/
+#define GPLL_LOCK_VAL	(0x546)
+/* EPLL_LOCK	*/
+#define EPLL_LOCK_VAL	(0x3A98)
+/* VPLL_LOCK	*/
+#define VPLL_LOCK_VAL	(0x3A98)
+/* BPLL_LOCK	*/
+#define BPLL_LOCK_VAL	(0x546)
+
+#define MUX_APLL_SEL_MASK	(1 << 0)
+#define MUX_MPLL_SEL_MASK	(1 << 8)
+#define MPLL_SEL_MOUT_MPLLFOUT	(2 << 8)
+#define MUX_CPLL_SEL_MASK	(1 << 8)
+#define MUX_EPLL_SEL_MASK	(1 << 12)
+#define MUX_VPLL_SEL_MASK	(1 << 16)
+#define MUX_GPLL_SEL_MASK	(1 << 28)
+#define MUX_BPLL_SEL_MASK	(1 << 0)
+#define MUX_HPM_SEL_MASK	(1 << 20)
+#define HPM_SEL_SCLK_MPLL	(1 << 21)
+#define APLL_CON0_LOCKED	(1 << 29)
+#define MPLL_CON0_LOCKED	(1 << 29)
+#define BPLL_CON0_LOCKED	(1 << 29)
+#define CPLL_CON0_LOCKED	(1 << 29)
+#define EPLL_CON0_LOCKED	(1 << 29)
+#define GPLL_CON0_LOCKED	(1 << 29)
+#define VPLL_CON0_LOCKED	(1 << 29)
+#define CLK_REG_DISABLE		0x0
+#define TOP2_VAL		0x0110000
+
+/* CLK_SRC_PERIC0 */
+#define PWM_SEL		6
+#define UART3_SEL	6
+#define UART2_SEL	6
+#define UART1_SEL	6
+#define UART0_SEL	6
+/* SRC_CLOCK = SCLK_MPLL */
+#define CLK_SRC_PERIC0_VAL	((PWM_SEL << 24)        \
+				| (UART3_SEL << 12)     \
+				| (UART2_SEL << 8)       \
+				| (UART1_SEL << 4)      \
+				| (UART0_SEL))
+
+/* CLK_SRC_PERIC1 */
+/* SRC_CLOCK = SCLK_MPLL */
+#define SPI0_SEL		6
+#define SPI1_SEL		6
+#define SPI2_SEL		6
+#define CLK_SRC_PERIC1_VAL	((SPI2_SEL << 24) \
+				| (SPI1_SEL << 20) \
+				| (SPI0_SEL << 16))
+
+/* SCLK_SRC_ISP - set SPI0/1 to 6 = SCLK_MPLL_USER */
+#define SPI0_ISP_SEL		6
+#define SPI1_ISP_SEL		6
+#define SCLK_SRC_ISP_VAL	(SPI1_ISP_SEL << 4) \
+				| (SPI0_ISP_SEL << 0)
+
+/* SCLK_DIV_ISP - set SPI0/1 to 0xf = divide by 16 */
+#define SPI0_ISP_RATIO		0xf
+#define SPI1_ISP_RATIO		0xf
+#define SCLK_DIV_ISP_VAL	(SPI1_ISP_RATIO << 12) \
+				| (SPI0_ISP_RATIO << 0)
+
+/* CLK_DIV_PERIL0	*/
+#define UART5_RATIO	7
+#define UART4_RATIO	7
+#define UART3_RATIO	7
+#define UART2_RATIO	7
+#define UART1_RATIO	7
+#define UART0_RATIO	7
+
+#define CLK_DIV_PERIC0_VAL	((UART3_RATIO << 12)    \
+				| (UART2_RATIO << 8)    \
+				| (UART1_RATIO << 4)    \
+				| (UART0_RATIO))
+/* CLK_DIV_PERIC1 */
+#define SPI1_RATIO		0x7
+#define SPI0_RATIO		0xf
+#define SPI1_SUB_RATIO		0x0
+#define SPI0_SUB_RATIO		0x0
+#define CLK_DIV_PERIC1_VAL	((SPI1_SUB_RATIO << 24) \
+				| ((SPI1_RATIO << 16) \
+				| (SPI0_SUB_RATIO << 8) \
+				| (SPI0_RATIO << 0)))
+
+/* CLK_DIV_PERIC2 */
+#define SPI2_RATIO		0xf
+#define SPI2_SUB_RATIO		0x0
+#define CLK_DIV_PERIC2_VAL	((SPI2_SUB_RATIO << 8) \
+				| (SPI2_RATIO << 0))
+
+/* CLK_DIV_PERIC3 */
+#define PWM_RATIO		8
+#define CLK_DIV_PERIC3_VAL	(PWM_RATIO << 0)
+
+/* CLK_DIV_FSYS2 */
+#define MMC2_RATIO_MASK		0xf
+#define MMC2_RATIO_VAL		0x3
+#define MMC2_RATIO_OFFSET	0
+
+#define MMC2_PRE_RATIO_MASK	0xff
+#define MMC2_PRE_RATIO_VAL	0x9
+#define MMC2_PRE_RATIO_OFFSET	8
+
+#define MMC3_RATIO_MASK		0xf
+#define MMC3_RATIO_VAL		0x1
+#define MMC3_RATIO_OFFSET	16
+
+#define MMC3_PRE_RATIO_MASK	0xff
+#define MMC3_PRE_RATIO_VAL	0x0
+#define MMC3_PRE_RATIO_OFFSET	24
+
+/* CLK_SRC_LEX */
+#define CLK_SRC_LEX_VAL         0x0
+
+/* CLK_DIV_LEX */
+#define CLK_DIV_LEX_VAL         0x10
+
+/* CLK_DIV_R0X */
+#define CLK_DIV_R0X_VAL         0x10
+
+/* CLK_DIV_L0X */
+#define CLK_DIV_R1X_VAL         0x10
+
+/* CLK_DIV_ISP0 */
+#define CLK_DIV_ISP0_VAL        0x31
+
+/* CLK_DIV_ISP1 */
+#define CLK_DIV_ISP1_VAL        0x0
+
+/* CLK_DIV_ISP2 */
+#define CLK_DIV_ISP2_VAL        0x1
+
+/* CLK_SRC_DISP1_0 */
+#define CLK_SRC_DISP1_0_VAL	0x6
+
+/*
+ * DIV_DISP1_0
+ * For DP, divisor should be 2
+ */
+#define CLK_DIV_DISP1_0_FIMD1	(2 << 0)
+
+/* CLK_GATE_IP_DISP1 */
+#define CLK_GATE_DP1_ALLOW	(1 << 4)
+
+#define DDR3PHY_CTRL_PHY_RESET	(1 << 0)
+#define DDR3PHY_CTRL_PHY_RESET_OFF	(0 << 0)
+
+#define PHY_CON0_RESET_VAL	0x17020a40
+#define P0_CMD_EN		(1 << 14)
+#define BYTE_RDLVL_EN		(1 << 13)
+#define CTRL_SHGATE		(1 << 8)
+
+#define PHY_CON1_RESET_VAL	0x09210100
+#define CTRL_GATEDURADJ_MASK	(0xf << 20)
+
+#define PHY_CON2_RESET_VAL	0x00010004
+#define INIT_DESKEW_EN		(1 << 6)
+#define RDLVL_GATE_EN		(1 << 24)
+
+/*ZQ Configurations */
+#define PHY_CON16_RESET_VAL	0x08000304
+
+#define ZQ_CLK_DIV_EN		(1 << 18)
+#define ZQ_MANUAL_STR		(1 << 1)
+#define ZQ_DONE			(1 << 0)
+
+#define CTRL_RDLVL_GATE_ENABLE	1
+#define CTRL_RDLVL_GATE_DISABLE	1
+
+/* Direct Command */
+#define DIRECT_CMD_NOP			0x07000000
+#define DIRECT_CMD_PALL			0x01000000
+#define DIRECT_CMD_ZQINIT		0x0a000000
+#define DIRECT_CMD_CHANNEL_SHIFT	28
+#define DIRECT_CMD_CHIP_SHIFT		20
+
+/* DMC PHY Control0 register */
+#define PHY_CONTROL0_RESET_VAL	0x0
+#define MEM_TERM_EN	(1 << 31)	/* Termination enable for memory */
+#define PHY_TERM_EN	(1 << 30)	/* Termination enable for PHY */
+#define DMC_CTRL_SHGATE	(1 << 29)	/* Duration of DQS gating signal */
+#define FP_RSYNC	(1 << 3)	/* Force DLL resyncronization */
+
+/* Driver strength for CK, CKE, CS & CA */
+#define IMP_OUTPUT_DRV_40_OHM	0x5
+#define IMP_OUTPUT_DRV_30_OHM	0x7
+#define CA_CK_DRVR_DS_OFFSET	9
+#define CA_CKE_DRVR_DS_OFFSET	6
+#define CA_CS_DRVR_DS_OFFSET	3
+#define CA_ADR_DRVR_DS_OFFSET	0
+
+#define PHY_CON42_CTRL_BSTLEN_SHIFT	8
+#define PHY_CON42_CTRL_RDLAT_SHIFT	0
+
+struct mem_timings;
+
+/* Errors that we can encourter in low-level setup */
+enum {
+	SETUP_ERR_OK,
+	SETUP_ERR_RDLV_COMPLETE_TIMEOUT = -1,
+	SETUP_ERR_ZQ_CALIBRATION_FAILURE = -2,
+};
+
+/*
+ * Memory variant specific initialization code
+ *
+ * @param mem		Memory timings for this memory type.
+ * @param mem_iv_size	Memory interleaving size is a configurable parameter
+ *			which the DMC uses to decide how to split a memory
+ *			chunk into smaller chunks to support concurrent
+ *			accesses; may vary across boards.
+ * @param reset         Reset DDR PHY during initialization.
+ * @return 0 if ok, SETUP_ERR_... if there is a problem
+ */
+int ddr3_mem_ctrl_init(struct mem_timings *mem, unsigned long mem_iv_size,
+			int reset);
+
+/*
+ * Configure ZQ I/O interface
+ *
+ * @param mem		Memory timings for this memory type.
+ * @param phy0_ctrl	Pointer to struct containing PHY0 control reg
+ * @param phy1_ctrl	Pointer to struct containing PHY1 control reg
+ * @return 0 if ok, -1 on error
+ */
+int dmc_config_zq(struct mem_timings *mem,
+		  struct exynos5_phy_control *phy0_ctrl,
+		  struct exynos5_phy_control *phy1_ctrl);
+
+/*
+ * Send NOP and MRS/EMRS Direct commands
+ *
+ * @param mem		Memory timings for this memory type.
+ * @param dmc		Pointer to struct of DMC registers
+ */
+void dmc_config_mrs(struct mem_timings *mem, struct exynos5_dmc *dmc);
+
+/*
+ * Send PALL Direct commands
+ *
+ * @param mem		Memory timings for this memory type.
+ * @param dmc		Pointer to struct of DMC registers
+ */
+void dmc_config_prech(struct mem_timings *mem, struct exynos5_dmc *dmc);
+
+/*
+ * Configure the memconfig and membaseconfig registers
+ *
+ * @param mem		Memory timings for this memory type.
+ * @param exynos5_dmc	Pointer to struct of DMC registers
+ */
+void dmc_config_memory(struct mem_timings *mem, struct exynos5_dmc *dmc);
+
+/*
+ * Reset the DLL. This function is common between DDR3 and LPDDR2.
+ * However, the reset value is different. So we are passing a flag
+ * ddr_mode to distinguish between LPDDR2 and DDR3.
+ *
+ * @param exynos5_dmc	Pointer to struct of DMC registers
+ * @param ddr_mode	Type of DDR memory
+ */
+void update_reset_dll(struct exynos5_dmc *, enum ddr_mode);
+#endif
diff --git a/arch/arm/cpu/armv7/exynos/lowlevel_init.c b/arch/arm/cpu/armv7/exynos/lowlevel_init.c
new file mode 100644
index 0000000..11fe5b8
--- /dev/null
+++ b/arch/arm/cpu/armv7/exynos/lowlevel_init.c
@@ -0,0 +1,73 @@
+/*
+ * Lowlevel setup for EXYNOS5 based board
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ * Rajeshwari Shinde <rajeshwari.s@samsung.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <config.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/dmc.h>
+#include <asm/arch/power.h>
+#include <asm/arch/tzpc.h>
+#include <asm/arch/periph.h>
+#include <asm/arch/pinmux.h>
+#include "common_setup.h"
+
+/* These are the things we can do during low-level init */
+enum {
+	DO_WAKEUP	= 1 << 0,
+	DO_CLOCKS	= 1 << 1,
+	DO_MEM_RESET	= 1 << 2,
+	DO_UART		= 1 << 3,
+};
+
+int do_lowlevel_init(void)
+{
+	uint32_t reset_status;
+	int actions = 0;
+
+	arch_cpu_init();
+
+	reset_status = get_reset_status();
+
+	switch (reset_status) {
+	case S5P_CHECK_SLEEP:
+		actions = DO_CLOCKS | DO_WAKEUP;
+		break;
+	case S5P_CHECK_DIDLE:
+	case S5P_CHECK_LPA:
+		actions = DO_WAKEUP;
+		break;
+	default:
+		/* This is a normal boot (not a wake from sleep) */
+		actions = DO_CLOCKS | DO_MEM_RESET;
+	}
+
+	if (actions & DO_CLOCKS) {
+		system_clock_init();
+		mem_ctrl_init(actions & DO_MEM_RESET);
+		tzpc_init();
+	}
+
+	return actions & DO_WAKEUP;
+}
diff --git a/arch/arm/cpu/armv7/exynos/spl_boot.c b/arch/arm/cpu/armv7/exynos/spl_boot.c
new file mode 100644
index 0000000..6e8dd3b
--- /dev/null
+++ b/arch/arm/cpu/armv7/exynos/spl_boot.c
@@ -0,0 +1,203 @@
+/*
+ * Copyright (C) 2012 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include<common.h>
+#include<config.h>
+
+#include <asm/arch/clock.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/dmc.h>
+#include <asm/arch/power.h>
+#include <asm/arch/spl.h>
+
+#include "common_setup.h"
+#include "clock_init.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+#define OM_STAT         (0x1f << 1)
+
+/* Index into irom ptr table */
+enum index {
+	MMC_INDEX,
+	EMMC44_INDEX,
+	EMMC44_END_INDEX,
+	SPI_INDEX,
+	USB_INDEX,
+};
+
+/* IROM Function Pointers Table */
+u32 irom_ptr_table[] = {
+	[MMC_INDEX] = 0x02020030,	/* iROM Function Pointer-SDMMC boot */
+	[EMMC44_INDEX] = 0x02020044,	/* iROM Function Pointer-EMMC4.4 boot*/
+	[EMMC44_END_INDEX] = 0x02020048,/* iROM Function Pointer
+						-EMMC4.4 end boot operation */
+	[SPI_INDEX] = 0x02020058,	/* iROM Function Pointer-SPI boot */
+	[USB_INDEX] = 0x02020070,	/* iROM Function Pointer-USB boot*/
+	};
+
+void *get_irom_func(int index)
+{
+	return (void *)*(u32 *)irom_ptr_table[index];
+}
+
+#ifdef CONFIG_USB_BOOTING
+/*
+ * Set/clear program flow prediction and return the previous state.
+ */
+static int config_branch_prediction(int set_cr_z)
+{
+	unsigned int cr;
+
+	/* System Control Register: 11th bit Z Branch prediction enable */
+	cr = get_cr();
+	set_cr(set_cr_z ? cr | CR_Z : cr & ~CR_Z);
+
+	return cr & CR_Z;
+}
+#endif
+
+/*
+* Copy U-boot from mmc to RAM:
+* COPY_BL2_FNPTR_ADDR: Address in iRAM, which Contains
+* Pointer to API (Data transfer from mmc to ram)
+*/
+void copy_uboot_to_ram(void)
+{
+	enum boot_mode bootmode = BOOT_MODE_OM;
+
+	u32 (*copy_bl2)(u32 offset, u32 nblock, u32 dst) = NULL;
+	u32 offset = 0, size = 0;
+#ifdef CONFIG_SUPPORT_EMMC_BOOT
+	u32 (*copy_bl2_from_emmc)(u32 nblock, u32 dst);
+	void (*end_bootop_from_emmc)(void);
+#endif
+#ifdef CONFIG_USB_BOOTING
+	u32 (*usb_copy)(void);
+	int is_cr_z_set;
+	unsigned int sec_boot_check;
+
+	/* Read iRAM location to check for secondary USB boot mode */
+	sec_boot_check = readl(EXYNOS_IRAM_SECONDARY_BASE);
+	if (sec_boot_check == EXYNOS_USB_SECONDARY_BOOT)
+		bootmode = BOOT_MODE_USB;
+#endif
+
+	if (bootmode == BOOT_MODE_OM)
+		bootmode = readl(samsung_get_base_power()) & OM_STAT;
+
+	switch (bootmode) {
+#ifdef CONFIG_SPI_BOOTING
+	case BOOT_MODE_SERIAL:
+		offset = SPI_FLASH_UBOOT_POS;
+		size = CONFIG_BL2_SIZE;
+		copy_bl2 = get_irom_func(SPI_INDEX);
+		break;
+#endif
+	case BOOT_MODE_MMC:
+		offset = BL2_START_OFFSET;
+		size = BL2_SIZE_BLOC_COUNT;
+		copy_bl2 = get_irom_func(MMC_INDEX);
+		break;
+#ifdef CONFIG_SUPPORT_EMMC_BOOT
+	case BOOT_MODE_EMMC:
+		/* Set the FSYS1 clock divisor value for EMMC boot */
+		emmc_boot_clk_div_set();
+
+		copy_bl2_from_emmc = get_irom_func(EMMC44_INDEX);
+		end_bootop_from_emmc = get_irom_func(EMMC44_END_INDEX);
+
+		copy_bl2_from_emmc(BL2_SIZE_BLOC_COUNT, CONFIG_SYS_TEXT_BASE);
+		end_bootop_from_emmc();
+		break;
+#endif
+#ifdef CONFIG_USB_BOOTING
+	case BOOT_MODE_USB:
+		/*
+		 * iROM needs program flow prediction to be disabled
+		 * before copy from USB device to RAM
+		 */
+		is_cr_z_set = config_branch_prediction(0);
+		usb_copy = get_irom_func(USB_INDEX);
+		usb_copy();
+		config_branch_prediction(is_cr_z_set);
+		break;
+#endif
+	default:
+		break;
+	}
+
+	if (copy_bl2)
+		copy_bl2(offset, size, CONFIG_SYS_TEXT_BASE);
+}
+
+void memzero(void *s, size_t n)
+{
+	char *ptr = s;
+	size_t i;
+
+	for (i = 0; i < n; i++)
+		*ptr++ = '\0';
+}
+
+/**
+ * Set up the U-Boot global_data pointer
+ *
+ * This sets the address of the global data, and sets up basic values.
+ *
+ * @param gdp   Value to give to gd
+ */
+static void setup_global_data(gd_t *gdp)
+{
+	gd = gdp;
+	memzero((void *)gd, sizeof(gd_t));
+	gd->flags |= GD_FLG_RELOC;
+	gd->baudrate = CONFIG_BAUDRATE;
+	gd->have_console = 1;
+}
+
+void board_init_f(unsigned long bootflag)
+{
+	__aligned(8) gd_t local_gd;
+	__attribute__((noreturn)) void (*uboot)(void);
+
+	setup_global_data(&local_gd);
+
+	if (do_lowlevel_init())
+		power_exit_wakeup();
+
+	copy_uboot_to_ram();
+
+	/* Jump to U-Boot image */
+	uboot = (void *)CONFIG_SYS_TEXT_BASE;
+	(*uboot)();
+	/* Never returns Here */
+}
+
+/* Place Holders */
+void board_init_r(gd_t *id, ulong dest_addr)
+{
+	/* Function attribute is no-return */
+	/* This Function never executes */
+	while (1)
+		;
+}
+void save_boot_params(u32 r0, u32 r1, u32 r2, u32 r3) {}
diff --git a/arch/arm/include/asm/arch-exynos/cpu.h b/arch/arm/include/asm/arch-exynos/cpu.h
index 36b98c8..8685c42 100644
--- a/arch/arm/include/asm/arch-exynos/cpu.h
+++ b/arch/arm/include/asm/arch-exynos/cpu.h
@@ -40,8 +40,7 @@
 #define EXYNOS4_WATCHDOG_BASE		0x10060000
 #define EXYNOS4_TZPC_BASE		0x10110000
 #define EXYNOS4_MIU_BASE		0x10600000
-#define EXYNOS4_DMC0_BASE		0x10400000
-#define EXYNOS4_DMC1_BASE		0x10410000
+#define EXYNOS4_DMC_CTRL_BASE		0x10400000
 #define EXYNOS4_GPIO_PART2_BASE		0x11000000
 #define EXYNOS4_GPIO_PART1_BASE		0x11400000
 #define EXYNOS4_FIMD_BASE		0x11C00000
@@ -64,6 +63,7 @@
 #define EXYNOS4_DP_BASE			DEVICE_NOT_AVAILABLE
 #define EXYNOS4_SPI_ISP_BASE		DEVICE_NOT_AVAILABLE
 #define EXYNOS4_ACE_SFR_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS4_DMC_PHY_BASE		DEVICE_NOT_AVAILABLE
 
 /* EXYNOS4X12 */
 #define EXYNOS4X12_GPIO_PART3_BASE	0x03860000
@@ -76,8 +76,7 @@
 #define EXYNOS4X12_SYSTIMER_BASE	0x10050000
 #define EXYNOS4X12_WATCHDOG_BASE	0x10060000
 #define EXYNOS4X12_TZPC_BASE		0x10110000
-#define EXYNOS4X12_DMC0_BASE		0x10600000
-#define EXYNOS4X12_DMC1_BASE		0x10610000
+#define EXYNOS4X12_DMC_CTRL_BASE	0x10600000
 #define EXYNOS4X12_GPIO_PART4_BASE	0x106E0000
 #define EXYNOS4X12_GPIO_PART2_BASE	0x11000000
 #define EXYNOS4X12_GPIO_PART1_BASE	0x11400000
@@ -99,6 +98,7 @@
 #define EXYNOS4X12_SPI_BASE		DEVICE_NOT_AVAILABLE
 #define EXYNOS4X12_SPI_ISP_BASE		DEVICE_NOT_AVAILABLE
 #define EXYNOS4X12_ACE_SFR_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS4X12_DMC_PHY_BASE		DEVICE_NOT_AVAILABLE
 
 /* EXYNOS5 Common*/
 #define EXYNOS5_I2C_SPACING		0x10000
@@ -112,8 +112,7 @@
 #define EXYNOS5_TZPC_BASE		0x10100000
 #define EXYNOS5_WATCHDOG_BASE		0x101D0000
 #define EXYNOS5_ACE_SFR_BASE            0x10830000
-#define EXYNOS5_DMC_PHY0_BASE		0x10C00000
-#define EXYNOS5_DMC_PHY1_BASE		0x10C10000
+#define EXYNOS5_DMC_PHY_BASE		0x10C00000
 #define EXYNOS5_GPIO_PART3_BASE		0x10D10000
 #define EXYNOS5_DMC_CTRL_BASE		0x10DD0000
 #define EXYNOS5_GPIO_PART1_BASE		0x11400000
@@ -237,6 +236,8 @@ SAMSUNG_BASE(power, POWER_BASE)
 SAMSUNG_BASE(spi, SPI_BASE)
 SAMSUNG_BASE(spi_isp, SPI_ISP_BASE)
 SAMSUNG_BASE(tzpc, TZPC_BASE)
+SAMSUNG_BASE(dmc_ctrl, DMC_CTRL_BASE)
+SAMSUNG_BASE(dmc_phy, DMC_PHY_BASE)
 #endif
 
 #endif	/* _EXYNOS4_CPU_H */