arm, imx6: add support for aristainetos2 board

add support for imx6dl based aristainetos2 board

U-Boot 2015.04-rc5-00066-g60f6ed4 (Apr 10 2015 - 08:46:27)

CPU:   Freescale i.MX6DL rev1.1 at 792 MHz
Reset cause: WDOG
Board: aristaitenos2
       Watchdog enabled
I2C:   ready
DRAM:  1 GiB
NAND:  1024 MiB
MMC:   FSL_SDHC: 0
SF: Detected N25Q128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB
Display: lg4573 (480x800)
In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0
=>

Signed-off-by: Heiko Schocher <hs@denx.de>

1 files changed, 627 insertions, 0 deletions

diff --git a/board/aristainetos/aristainetos-v2.c b/board/aristainetos/aristainetos-v2.c
new file mode 100644
index 0000000..7a44031
--- /dev/null
+++ b/board/aristainetos/aristainetos-v2.c
@@ -0,0 +1,627 @@
+/*
+ * (C) Copyright 2015
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * Based on:
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * Author: Fabio Estevam <fabio.estevam@freescale.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/video.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/crm_regs.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <pwm.h>
+#include <micrel.h>
+#include <spi.h>
+#include <video.h>
+#include <../drivers/video/ipu.h>
+#if defined(CONFIG_VIDEO_BMP_LOGO)
+	#include <bmp_logo.h>
+#endif
+
+#define USDHC2_PAD_CTRL (PAD_CTL_SPEED_LOW |			\
+	PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define ECSPI1_CS0		IMX_GPIO_NR(4, 9)   /* 4.3 display controller */
+#define ECSPI4_CS0		IMX_GPIO_NR(3, 29)
+#define SOFT_RESET_GPIO		IMX_GPIO_NR(7, 13)
+#define SD2_DRIVER_ENABLE	IMX_GPIO_NR(7, 8)
+
+struct i2c_pads_info i2c_pad_info3 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | PC,
+		.gpio_mode = MX6_PAD_GPIO_5__GPIO1_IO05 | PC,
+		.gp = IMX_GPIO_NR(1, 5)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | PC,
+		.gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | PC,
+		.gp = IMX_GPIO_NR(1, 6)
+	}
+};
+
+struct i2c_pads_info i2c_pad_info4 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_GPIO_7__I2C4_SCL | PC,
+		.gpio_mode = MX6_PAD_GPIO_7__GPIO1_IO07 | PC,
+		.gp = IMX_GPIO_NR(1, 7)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO_8__I2C4_SDA | PC,
+		.gpio_mode = MX6_PAD_GPIO_8__GPIO1_IO08 | PC,
+		.gp = IMX_GPIO_NR(1, 8)
+	}
+};
+
+iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D19__UART1_CTS_B    | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D20__UART1_RTS_B    | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart2_pads[] = {
+	MX6_PAD_EIM_D26__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D27__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart3_pads[] = {
+	MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const uart4_pads[] = {
+	MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const gpio_pads[] = {
+	/* LED enable*/
+	MX6_PAD_ENET_CRS_DV__GPIO1_IO25 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* LED yellow */
+	MX6_PAD_NANDF_CS3__GPIO6_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* LED red */
+	MX6_PAD_EIM_EB0__GPIO2_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* LED green */
+	MX6_PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* LED blue */
+	MX6_PAD_EIM_EB1__GPIO2_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* spi flash WP protect */
+	MX6_PAD_SD4_DAT7__GPIO2_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* spi CS 0 */
+	MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* spi bus #2 SS driver enable */
+	MX6_PAD_EIM_A23__GPIO6_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* RST_LOC# PHY reset input (has pull-down!)*/
+	MX6_PAD_GPIO_18__GPIO7_IO13 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* SD 2 level shifter output enable */
+	MX6_PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* SD1 card detect input */
+	MX6_PAD_ENET_RXD0__GPIO1_IO27 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* SD1 write protect input */
+	MX6_PAD_DI0_PIN4__GPIO4_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* SD2 card detect input */
+	MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* SD2 write protect input */
+	MX6_PAD_SD4_DAT2__GPIO2_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* Touchscreen IRQ */
+	MX6_PAD_SD4_DAT1__GPIO2_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const misc_pads[] = {
+	/* USB_OTG_ID = GPIO1_24*/
+	MX6_PAD_ENET_RX_ER__USB_OTG_ID		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* H1 Power enable = GPIO1_0*/
+	MX6_PAD_GPIO_0__USB_H1_PWR		| MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* OTG Power enable = GPIO4_15*/
+	MX6_PAD_KEY_ROW4__USB_OTG_PWR		| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+iomux_v3_cfg_t const enet_pads[] = {
+	MX6_PAD_ENET_MDIO__ENET_MDIO		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TXC__RGMII_TXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD0__RGMII_TD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD1__RGMII_TD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD2__RGMII_TD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD3__RGMII_TD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RXC__RGMII_RXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD0__RGMII_RD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD1__RGMII_RD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD2__RGMII_RD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RD3__RGMII_RD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const backlight_pads[] = {
+	/* backlight PWM brightness control */
+	MX6_PAD_GPIO_9__PWM1_OUT | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* backlight enable */
+	MX6_PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* LCD power enable */
+	MX6_PAD_NANDF_CS2__GPIO6_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const ecspi1_pads[] = {
+	MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_KEY_ROW1__GPIO4_IO09 | MUX_PAD_CTRL(SPI_PAD_CTRL),
+};
+
+static void setup_iomux_enet(void)
+{
+	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+}
+
+iomux_v3_cfg_t const ecspi4_pads[] = {
+	MX6_PAD_EIM_D21__ECSPI4_SCLK | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_EIM_D22__ECSPI4_MISO | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_EIM_D28__ECSPI4_MOSI | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_EIM_A25__GPIO5_IO02  | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_EIM_D29__GPIO3_IO29  | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const display_pads[] = {
+	MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK | MUX_PAD_CTRL(DISP_PAD_CTRL),
+	MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15,
+	MX6_PAD_DI0_PIN2__IPU1_DI0_PIN02,
+	MX6_PAD_DI0_PIN3__IPU1_DI0_PIN03,
+	MX6_PAD_DI0_PIN4__GPIO4_IO20,
+	MX6_PAD_DISP0_DAT0__IPU1_DISP0_DATA00,
+	MX6_PAD_DISP0_DAT1__IPU1_DISP0_DATA01,
+	MX6_PAD_DISP0_DAT2__IPU1_DISP0_DATA02,
+	MX6_PAD_DISP0_DAT3__IPU1_DISP0_DATA03,
+	MX6_PAD_DISP0_DAT4__IPU1_DISP0_DATA04,
+	MX6_PAD_DISP0_DAT5__IPU1_DISP0_DATA05,
+	MX6_PAD_DISP0_DAT6__IPU1_DISP0_DATA06,
+	MX6_PAD_DISP0_DAT7__IPU1_DISP0_DATA07,
+	MX6_PAD_DISP0_DAT8__IPU1_DISP0_DATA08,
+	MX6_PAD_DISP0_DAT9__IPU1_DISP0_DATA09,
+	MX6_PAD_DISP0_DAT10__IPU1_DISP0_DATA10,
+	MX6_PAD_DISP0_DAT11__IPU1_DISP0_DATA11,
+	MX6_PAD_DISP0_DAT12__IPU1_DISP0_DATA12,
+	MX6_PAD_DISP0_DAT13__IPU1_DISP0_DATA13,
+	MX6_PAD_DISP0_DAT14__IPU1_DISP0_DATA14,
+	MX6_PAD_DISP0_DAT15__IPU1_DISP0_DATA15,
+	MX6_PAD_DISP0_DAT16__IPU1_DISP0_DATA16,
+	MX6_PAD_DISP0_DAT17__IPU1_DISP0_DATA17,
+	MX6_PAD_DISP0_DAT18__IPU1_DISP0_DATA18,
+	MX6_PAD_DISP0_DAT19__IPU1_DISP0_DATA19,
+	MX6_PAD_DISP0_DAT20__IPU1_DISP0_DATA20,
+	MX6_PAD_DISP0_DAT21__IPU1_DISP0_DATA21,
+	MX6_PAD_DISP0_DAT22__IPU1_DISP0_DATA22,
+	MX6_PAD_DISP0_DAT23__IPU1_DISP0_DATA23,
+};
+
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+	if (bus == CONFIG_SF_DEFAULT_BUS && cs == CONFIG_SF_DEFAULT_CS)
+		return IMX_GPIO_NR(5, 2);
+
+	if (bus == 0 && cs == 0)
+		return IMX_GPIO_NR(4, 9);
+
+	return -1;
+}
+
+static void setup_spi(void)
+{
+	int i;
+
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+	imx_iomux_v3_setup_multiple_pads(ecspi4_pads, ARRAY_SIZE(ecspi4_pads));
+	for (i = 0; i < 4; i++)
+		enable_spi_clk(true, i);
+
+	gpio_direction_output(ECSPI1_CS0, 1);
+	gpio_direction_output(ECSPI4_CS1, 0);
+
+	/* set cs0 to high (second device on spi bus #4) */
+	gpio_direction_output(ECSPI4_CS0, 1);
+}
+
+static void setup_iomux_uart(void)
+{
+	switch (CONFIG_MXC_UART_BASE) {
+	case UART1_BASE:
+		imx_iomux_v3_setup_multiple_pads(uart1_pads,
+						 ARRAY_SIZE(uart1_pads));
+		break;
+	case UART2_BASE:
+		imx_iomux_v3_setup_multiple_pads(uart2_pads,
+						 ARRAY_SIZE(uart2_pads));
+		break;
+	case UART3_BASE:
+		imx_iomux_v3_setup_multiple_pads(uart3_pads,
+						 ARRAY_SIZE(uart3_pads));
+		break;
+	case UART4_BASE:
+		imx_iomux_v3_setup_multiple_pads(uart4_pads,
+						 ARRAY_SIZE(uart4_pads));
+		break;
+	}
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	/* control data pad skew - devaddr = 0x02, register = 0x04 */
+	ksz9031_phy_extended_write(phydev, 0x02,
+				   MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW,
+				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
+	/* rx data pad skew - devaddr = 0x02, register = 0x05 */
+	ksz9031_phy_extended_write(phydev, 0x02,
+				   MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW,
+				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
+	/* tx data pad skew - devaddr = 0x02, register = 0x06 */
+	ksz9031_phy_extended_write(phydev, 0x02,
+				   MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
+				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x0000);
+	/* gtx and rx clock pad skew - devaddr = 0x02, register = 0x08 */
+	ksz9031_phy_extended_write(phydev, 0x02,
+				   MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
+				   MII_KSZ9031_MOD_DATA_NO_POST_INC, 0x03FF);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	setup_iomux_enet();
+	return cpu_eth_init(bis);
+}
+
+static int rotate_logo_one(unsigned char *out, unsigned char *in)
+{
+	int   i, j;
+
+	for (i = 0; i < BMP_LOGO_WIDTH; i++)
+		for (j = 0; j < BMP_LOGO_HEIGHT; j++)
+			out[j * BMP_LOGO_WIDTH + BMP_LOGO_HEIGHT - 1 - i] =
+			in[i * BMP_LOGO_WIDTH + j];
+	return 0;
+}
+
+/*
+ * Rotate the BMP_LOGO (only)
+ * Will only work, if the logo is square, as
+ * BMP_LOGO_HEIGHT and BMP_LOGO_WIDTH are defines, not variables
+ */
+void rotate_logo(int rotations)
+{
+	unsigned char out_logo[BMP_LOGO_WIDTH * BMP_LOGO_HEIGHT];
+	unsigned char *in_logo;
+	int   i, j;
+
+	if (BMP_LOGO_WIDTH != BMP_LOGO_HEIGHT)
+		return;
+
+	in_logo = bmp_logo_bitmap;
+
+	/* one 90 degree rotation */
+	if (rotations == 1  ||  rotations == 2  ||  rotations == 3)
+		rotate_logo_one(out_logo, in_logo);
+
+	/* second 90 degree rotation */
+	if (rotations == 2  ||  rotations == 3)
+		rotate_logo_one(in_logo, out_logo);
+
+	/* third 90 degree rotation */
+	if (rotations == 3)
+		rotate_logo_one(out_logo, in_logo);
+
+	/* copy result back to original array */
+	if (rotations == 1  ||  rotations == 3)
+		for (i = 0; i < BMP_LOGO_WIDTH; i++)
+			for (j = 0; j < BMP_LOGO_HEIGHT; j++)
+				in_logo[i * BMP_LOGO_WIDTH + j] =
+				out_logo[i * BMP_LOGO_WIDTH + j];
+}
+
+static void enable_display_power(void)
+{
+	imx_iomux_v3_setup_multiple_pads(backlight_pads,
+					 ARRAY_SIZE(backlight_pads));
+
+	/* backlight enable */
+	gpio_direction_output(IMX_GPIO_NR(6, 31), 1);
+	/* LCD power enable */
+	gpio_direction_output(IMX_GPIO_NR(6, 15), 1);
+
+	/* enable backlight PWM 1 */
+	if (pwm_init(0, 0, 0))
+		goto error;
+	/* duty cycle 500ns, period: 3000ns */
+	if (pwm_config(0, 50000, 300000))
+		goto error;
+	if (pwm_enable(0))
+		goto error;
+	return;
+
+error:
+	puts("error init pwm for backlight\n");
+	return;
+}
+
+static void enable_lvds(struct display_info_t const *dev)
+{
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	int reg;
+	s32 timeout = 100000;
+
+	/* set PLL5 clock */
+	reg = readl(&ccm->analog_pll_video);
+	reg |= BM_ANADIG_PLL_VIDEO_POWERDOWN;
+	writel(reg, &ccm->analog_pll_video);
+
+	/* set PLL5 to 232720000Hz */
+	reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
+	reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(0x26);
+	reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
+	reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0);
+	writel(reg, &ccm->analog_pll_video);
+
+	writel(BF_ANADIG_PLL_VIDEO_NUM_A(0xC0238),
+	       &ccm->analog_pll_video_num);
+	writel(BF_ANADIG_PLL_VIDEO_DENOM_B(0xF4240),
+	       &ccm->analog_pll_video_denom);
+
+	reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
+	writel(reg, &ccm->analog_pll_video);
+
+	while (timeout--)
+		if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
+			break;
+	if (timeout < 0)
+		printf("Warning: video pll lock timeout!\n");
+
+	reg = readl(&ccm->analog_pll_video);
+	reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
+	reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
+	writel(reg, &ccm->analog_pll_video);
+
+	/* set LDB0, LDB1 clk select to 000/000 (PLL5 clock) */
+	reg = readl(&ccm->cs2cdr);
+	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+		 | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+	reg |= (0 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
+		| (0 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
+	writel(reg, &ccm->cs2cdr);
+
+	reg = readl(&ccm->cscmr2);
+	reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
+	writel(reg, &ccm->cscmr2);
+
+	reg = readl(&ccm->chsccdr);
+	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+	writel(reg, &ccm->chsccdr);
+
+	reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
+	      | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
+	      | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_HIGH
+	      | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
+	      | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT
+	      | IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED
+	      | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
+	writel(reg, &iomux->gpr[2]);
+
+	reg = readl(&iomux->gpr[3]);
+	reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK)
+	       | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+		  << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
+	writel(reg, &iomux->gpr[3]);
+
+	return;
+}
+
+static void enable_spi_display(struct display_info_t const *dev)
+{
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	int reg;
+	s32 timeout = 100000;
+
+#if defined(CONFIG_VIDEO_BMP_LOGO)
+	rotate_logo(3);  /* portrait display in landscape mode */
+#endif
+
+	/*
+	 * set ldb clock to 28341000 Hz calculated through the formula:
+	 * (XRES + LEFT_M + RIGHT_M + HSYNC_LEN) *
+	 * (YRES + UPPER_M + LOWER_M + VSYNC_LEN) * REFRESH)
+	 * see:
+	 * https://community.freescale.com/thread/308170
+	 */
+	ipu_set_ldb_clock(28341000);
+
+	reg = readl(&ccm->cs2cdr);
+
+	/* select pll 5 clock */
+	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+		| MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+	writel(reg, &ccm->cs2cdr);
+
+	/* set PLL5 to 197994996Hz */
+	reg &= ~BM_ANADIG_PLL_VIDEO_DIV_SELECT;
+	reg |= BF_ANADIG_PLL_VIDEO_DIV_SELECT(0x21);
+	reg &= ~BM_ANADIG_PLL_VIDEO_POST_DIV_SELECT;
+	reg |= BF_ANADIG_PLL_VIDEO_POST_DIV_SELECT(0);
+	writel(reg, &ccm->analog_pll_video);
+
+	writel(BF_ANADIG_PLL_VIDEO_NUM_A(0xfbf4),
+	       &ccm->analog_pll_video_num);
+	writel(BF_ANADIG_PLL_VIDEO_DENOM_B(0xf4240),
+	       &ccm->analog_pll_video_denom);
+
+	reg &= ~BM_ANADIG_PLL_VIDEO_POWERDOWN;
+	writel(reg, &ccm->analog_pll_video);
+
+	while (timeout--)
+		if (readl(&ccm->analog_pll_video) & BM_ANADIG_PLL_VIDEO_LOCK)
+			break;
+	if (timeout < 0)
+		printf("Warning: video pll lock timeout!\n");
+
+	reg = readl(&ccm->analog_pll_video);
+	reg |= BM_ANADIG_PLL_VIDEO_ENABLE;
+	reg &= ~BM_ANADIG_PLL_VIDEO_BYPASS;
+	writel(reg, &ccm->analog_pll_video);
+
+	/* set LDB0, LDB1 clk select to 000/000 (PLL5 clock) */
+	reg = readl(&ccm->cs2cdr);
+	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
+		 | MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+	reg |= (0 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
+		| (0 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
+	writel(reg, &ccm->cs2cdr);
+
+	reg = readl(&ccm->cscmr2);
+	reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
+	writel(reg, &ccm->cscmr2);
+
+	reg = readl(&ccm->chsccdr);
+	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+	reg &= ~MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK;
+	reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET);
+	reg &= ~MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK;
+	reg |= (2 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
+	writel(reg, &ccm->chsccdr);
+
+	reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
+	      | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
+	      | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_HIGH
+	      | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
+	      | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT
+	      | IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED
+	      | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
+	writel(reg, &iomux->gpr[2]);
+
+	reg = readl(&iomux->gpr[3]);
+	reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK)
+	       | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+		  << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
+	writel(reg, &iomux->gpr[3]);
+
+	imx_iomux_v3_setup_multiple_pads(
+		display_pads,
+		 ARRAY_SIZE(display_pads));
+
+	return;
+}
+static void setup_display(void)
+{
+	enable_ipu_clock();
+	enable_display_power();
+}
+
+static void setup_iomux_gpio(void)
+{
+	imx_iomux_v3_setup_multiple_pads(gpio_pads, ARRAY_SIZE(gpio_pads));
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+	setup_iomux_gpio();
+
+	gpio_direction_output(SOFT_RESET_GPIO, 1);
+	gpio_direction_output(SD2_DRIVER_ENABLE, 1);
+	setup_display();
+	return 0;
+}
+
+static void setup_i2c4(void)
+{
+	setup_i2c(3, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
+		  &i2c_pad_info4);
+}
+
+static void setup_board_gpio(void)
+{
+	/* enable all LEDs */
+	gpio_request(IMX_GPIO_NR(2, 13), "LED ena"); /* 25 */
+	gpio_direction_output(IMX_GPIO_NR(1, 25), 0);
+
+	/* switch off Status LEDs */
+	gpio_request(IMX_GPIO_NR(6, 16), "LED yellow"); /* 176 */
+	gpio_direction_output(IMX_GPIO_NR(6, 16), 1);
+	gpio_request(IMX_GPIO_NR(2, 28), "LED red"); /* 60 */
+	gpio_direction_output(IMX_GPIO_NR(2, 28), 1);
+	gpio_request(IMX_GPIO_NR(5, 4), "LED green"); /* 132 */
+	gpio_direction_output(IMX_GPIO_NR(5, 4), 1);
+	gpio_request(IMX_GPIO_NR(2, 29), "LED blue"); /* 61 */
+	gpio_direction_output(IMX_GPIO_NR(2, 29), 1);
+}
+
+static void setup_board_spi(void)
+{
+	/* enable spi bus #2 SS drivers */
+	gpio_direction_output(IMX_GPIO_NR(6, 6), 1);
+}
+
+int board_late_init(void)
+{
+	char *my_bootdelay;
+	char bootmode = 0;
+	char const *panel = getenv("panel");
+
+	/*
+	 * Check the boot-source. If booting from NOR Flash,
+	 * disable bootdelay
+	 */
+	gpio_request(IMX_GPIO_NR(7, 6), "bootsel0");
+	gpio_direction_input(IMX_GPIO_NR(7, 6));
+	gpio_request(IMX_GPIO_NR(7, 7), "bootsel1");
+	gpio_direction_input(IMX_GPIO_NR(7, 7));
+	gpio_request(IMX_GPIO_NR(7, 1), "bootsel2");
+	gpio_direction_input(IMX_GPIO_NR(7, 1));
+	bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 6)) ? 1 : 0) << 0;
+	bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 7)) ? 1 : 0) << 1;
+	bootmode |= (gpio_get_value(IMX_GPIO_NR(7, 1)) ? 1 : 0) << 2;
+
+	if (bootmode == 7) {
+		my_bootdelay = getenv("nor_bootdelay");
+		if (my_bootdelay != NULL)
+			setenv("bootdelay", my_bootdelay);
+		else
+			setenv("bootdelay", "-2");
+	}
+
+	/* if we have the lg panel, we can initialze it now */
+	if (panel)
+		if (!strcmp(panel, displays[1].mode.name))
+			lg4573_spi_startup(0, 0, 10000000, SPI_MODE_0);
+
+	return 0;
+}
+