armv8: layerscape: Rewrite memory reservation

For ARMv8 Layerscape SoCs, secure memory and MC memorey are reserved
at the end of DDR. DDR is spit into two or three banks. This patch
reverts commit aabd7ddb and simplifies the calculation of reserved
memory, and moves the code into common SoC file. Secure memory is
carved out first. DDR bank size is reduced. Reserved memory is then
allocated on the top of available memory. U-Boot still has access
to reserved memory as data transferring is needed. Device tree is
fixed with reduced memory size to hide the reserved memory from OS.
The same region is reserved for efi_loader.

Signed-off-by: York Sun <york.sun@nxp.com>

2 files changed, 10 insertions, 63 deletions

diff --git a/board/freescale/ls2080ardb/ddr.c b/board/freescale/ls2080ardb/ddr.c
index 959dfeb..2851d5b 100644
--- a/board/freescale/ls2080ardb/ddr.c
+++ b/board/freescale/ls2080ardb/ddr.c
@@ -172,58 +172,3 @@ phys_size_t initdram(int board_type)
 
 	return dram_size;
 }
-
-void dram_init_banksize(void)
-{
-#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
-	phys_size_t dp_ddr_size;
-#endif
-
-	/*
-	 * gd->arch.secure_ram tracks the location of secure memory.
-	 * It was set as if the memory starts from 0.
-	 * The address needs to add the offset of its bank.
-	 */
-	gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
-	if (gd->ram_size > CONFIG_SYS_LS2_DDR_BLOCK1_SIZE) {
-		gd->bd->bi_dram[0].size = CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
-		gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
-		gd->bd->bi_dram[1].size = gd->ram_size -
-					  CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
-		gd->arch.secure_ram = gd->bd->bi_dram[1].start +
-				      gd->arch.secure_ram -
-				      CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
-		gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
-	} else {
-		gd->bd->bi_dram[0].size = gd->ram_size;
-#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
-		gd->arch.secure_ram = gd->bd->bi_dram[0].start +
-				      gd->arch.secure_ram;
-		gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
-#endif
-	}
-
-#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
-	if (soc_has_dp_ddr()) {
-		/* initialize DP-DDR here */
-		puts("DP-DDR:  ");
-		/*
-		 * DDR controller use 0 as the base address for binding.
-		 * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
-		 */
-		dp_ddr_size = fsl_other_ddr_sdram(CONFIG_SYS_DP_DDR_BASE_PHY,
-					  CONFIG_DP_DDR_CTRL,
-					  CONFIG_DP_DDR_NUM_CTRLS,
-					  CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR,
-					  NULL, NULL, NULL);
-		if (dp_ddr_size) {
-			gd->bd->bi_dram[2].start = CONFIG_SYS_DP_DDR_BASE;
-			gd->bd->bi_dram[2].size = dp_ddr_size;
-		} else {
-			puts("Not detected");
-		}
-	}
-#endif
-}
diff --git a/board/freescale/ls2080ardb/ls2080ardb.c b/board/freescale/ls2080ardb/ls2080ardb.c
index 02954ef..7a4c6a3 100644
--- a/board/freescale/ls2080ardb/ls2080ardb.c
+++ b/board/freescale/ls2080ardb/ls2080ardb.c
@@ -202,14 +202,6 @@ int misc_init_r(void)
 	if (adjust_vdd(0))
 		printf("Warning: Adjusting core voltage failed.\n");
 
-#if defined(CONFIG_EFI_LOADER) && !defined(CONFIG_SPL_BUILD)
-	if (soc_has_dp_ddr() && gd->bd->bi_dram[2].size) {
-		efi_add_memory_map(gd->bd->bi_dram[2].start,
-				   gd->bd->bi_dram[2].size >> EFI_PAGE_SHIFT,
-				   EFI_RESERVED_MEMORY_TYPE, false);
-	}
-#endif
-
 	return 0;
 }
 
@@ -286,6 +278,16 @@ int ft_board_setup(void *blob, bd_t *bd)
 	base[1] = gd->bd->bi_dram[1].start;
 	size[1] = gd->bd->bi_dram[1].size;
 
+#ifdef CONFIG_RESV_RAM
+	/* reduce size if reserved memory is within this bank */
+	if (gd->arch.resv_ram >= base[0] &&
+	    gd->arch.resv_ram < base[0] + size[0])
+		size[0] = gd->arch.resv_ram - base[0];
+	else if (gd->arch.resv_ram >= base[1] &&
+		 gd->arch.resv_ram < base[1] + size[1])
+		size[1] = gd->arch.resv_ram - base[1];
+#endif
+
 	fdt_fixup_memory_banks(blob, base, size, 2);
 
 	fsl_fdt_fixup_dr_usb(blob, bd);