ARM: sunxi: move board/sunxi/Kconfig to arch/arm/mach-sunxi/Kconfig

For the consistent location of SoC-level Kconfig.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

1 files changed, 0 insertions, 792 deletions

diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig
deleted file mode 100644
index ac3be30..0000000
--- a/board/sunxi/Kconfig
+++ /dev/null
@@ -1,792 +0,0 @@
-if ARCH_SUNXI
-
-config IDENT_STRING
-	default " Allwinner Technology"
-
-# FIXME: Should not redefine these Kconfig symbols
-config PRE_CONSOLE_BUFFER
-	default y
-
-config SPL_GPIO_SUPPORT
-	default y
-
-config SPL_LIBCOMMON_SUPPORT
-	default y
-
-config SPL_LIBDISK_SUPPORT
-	default y
-
-config SPL_LIBGENERIC_SUPPORT
-	default y
-
-config SPL_MMC_SUPPORT
-	depends on SPL && GENERIC_MMC
-	default y
-
-config SPL_POWER_SUPPORT
-	default y
-
-config SPL_SERIAL_SUPPORT
-	default y
-
-config SUNXI_HIGH_SRAM
-	bool
-	default n
-	---help---
-	Older Allwinner SoCs have their mask boot ROM mapped just below 4GB,
-	with the first SRAM region being located at address 0.
-	Some newer SoCs map the boot ROM at address 0 instead and move the
-	SRAM to 64KB, just behind the mask ROM.
-	Chips using the latter setup are supposed to select this option to
-	adjust the addresses accordingly.
-
-# Note only one of these may be selected at a time! But hidden choices are
-# not supported by Kconfig
-config SUNXI_GEN_SUN4I
-	bool
-	---help---
-	Select this for sunxi SoCs which have resets and clocks set up
-	as the original A10 (mach-sun4i).
-
-config SUNXI_GEN_SUN6I
-	bool
-	---help---
-	Select this for sunxi SoCs which have sun6i like periphery, like
-	separate ahb reset control registers, custom pmic bus, new style
-	watchdog, etc.
-
-
-config MACH_SUNXI_H3_H5
-	bool
-	select DM_I2C
-	select SUNXI_DE2
-	select SUNXI_GEN_SUN6I
-	select SUPPORT_SPL
-
-choice
-	prompt "Sunxi SoC Variant"
-	optional
-
-config MACH_SUN4I
-	bool "sun4i (Allwinner A10)"
-	select CPU_V7
-	select ARM_CORTEX_CPU_IS_UP
-	select SUNXI_GEN_SUN4I
-	select SUPPORT_SPL
-
-config MACH_SUN5I
-	bool "sun5i (Allwinner A13)"
-	select CPU_V7
-	select ARM_CORTEX_CPU_IS_UP
-	select SUNXI_GEN_SUN4I
-	select SUPPORT_SPL
-
-config MACH_SUN6I
-	bool "sun6i (Allwinner A31)"
-	select CPU_V7
-	select CPU_V7_HAS_NONSEC
-	select CPU_V7_HAS_VIRT
-	select ARCH_SUPPORT_PSCI
-	select SUNXI_GEN_SUN6I
-	select SUPPORT_SPL
-	select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
-
-config MACH_SUN7I
-	bool "sun7i (Allwinner A20)"
-	select CPU_V7
-	select CPU_V7_HAS_NONSEC
-	select CPU_V7_HAS_VIRT
-	select ARCH_SUPPORT_PSCI
-	select SUNXI_GEN_SUN4I
-	select SUPPORT_SPL
-	select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
-
-config MACH_SUN8I_A23
-	bool "sun8i (Allwinner A23)"
-	select CPU_V7
-	select CPU_V7_HAS_NONSEC
-	select CPU_V7_HAS_VIRT
-	select ARCH_SUPPORT_PSCI
-	select SUNXI_GEN_SUN6I
-	select SUPPORT_SPL
-	select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
-
-config MACH_SUN8I_A33
-	bool "sun8i (Allwinner A33)"
-	select CPU_V7
-	select CPU_V7_HAS_NONSEC
-	select CPU_V7_HAS_VIRT
-	select ARCH_SUPPORT_PSCI
-	select SUNXI_GEN_SUN6I
-	select SUPPORT_SPL
-	select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
-
-config MACH_SUN8I_A83T
-	bool "sun8i (Allwinner A83T)"
-	select CPU_V7
-	select SUNXI_GEN_SUN6I
-	select SUPPORT_SPL
-
-config MACH_SUN8I_H3
-	bool "sun8i (Allwinner H3)"
-	select CPU_V7
-	select CPU_V7_HAS_NONSEC
-	select CPU_V7_HAS_VIRT
-	select ARCH_SUPPORT_PSCI
-	select MACH_SUNXI_H3_H5
-	select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
-
-config MACH_SUN8I_R40
-	bool "sun8i (Allwinner R40)"
-	select CPU_V7
-	select CPU_V7_HAS_NONSEC
-	select CPU_V7_HAS_VIRT
-	select ARCH_SUPPORT_PSCI
-	select SUNXI_GEN_SUN6I
-	select SUPPORT_SPL
-
-config MACH_SUN8I_V3S
-	bool "sun8i (Allwinner V3s)"
-	select CPU_V7
-	select CPU_V7_HAS_NONSEC
-	select CPU_V7_HAS_VIRT
-	select ARCH_SUPPORT_PSCI
-	select SUNXI_GEN_SUN6I
-	select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
-
-config MACH_SUN9I
-	bool "sun9i (Allwinner A80)"
-	select CPU_V7
-	select SUNXI_HIGH_SRAM
-	select SUNXI_GEN_SUN6I
-	select SUPPORT_SPL
-
-config MACH_SUN50I
-	bool "sun50i (Allwinner A64)"
-	select ARM64
-	select DM_I2C
-	select SUNXI_DE2
-	select SUNXI_GEN_SUN6I
-	select SUNXI_HIGH_SRAM
-	select SUPPORT_SPL
-
-config MACH_SUN50I_H5
-	bool "sun50i (Allwinner H5)"
-	select ARM64
-	select MACH_SUNXI_H3_H5
-	select SUNXI_HIGH_SRAM
-
-endchoice
-
-# The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33"
-config MACH_SUN8I
-	bool
-	default y if MACH_SUN8I_A23
-	default y if MACH_SUN8I_A33
-	default y if MACH_SUN8I_A83T
-	default y if MACH_SUNXI_H3_H5
-	default y if MACH_SUN8I_R40
-	default y if MACH_SUN8I_V3S
-
-config RESERVE_ALLWINNER_BOOT0_HEADER
-	bool "reserve space for Allwinner boot0 header"
-	select ENABLE_ARM_SOC_BOOT0_HOOK
-	---help---
-	Prepend a 1536 byte (empty) header to the U-Boot image file, to be
-	filled with magic values post build. The Allwinner provided boot0
-	blob relies on this information to load and execute U-Boot.
-	Only needed on 64-bit Allwinner boards so far when using boot0.
-
-config ARM_BOOT_HOOK_RMR
-	bool
-	depends on ARM64
-	default y
-	select ENABLE_ARM_SOC_BOOT0_HOOK
-	---help---
-	Insert some ARM32 code at the very beginning of the U-Boot binary
-	which uses an RMR register write to bring the core into AArch64 mode.
-	The very first instruction acts as a switch, since it's carefully
-	chosen to be a NOP in one mode and a branch in the other, so the
-	code would only be executed if not already in AArch64.
-	This allows both the SPL and the U-Boot proper to be entered in
-	either mode and switch to AArch64 if needed.
-
-config DRAM_TYPE
-	int "sunxi dram type"
-	depends on MACH_SUN8I_A83T
-	default 3
-	---help---
-	Set the dram type, 3: DDR3, 7: LPDDR3
-
-config DRAM_CLK
-	int "sunxi dram clock speed"
-	default 792 if MACH_SUN9I
-	default 648 if MACH_SUN8I_R40
-	default 312 if MACH_SUN6I || MACH_SUN8I
-	default 360 if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
-	default 672 if MACH_SUN50I
-	---help---
-	Set the dram clock speed, valid range 240 - 480 (prior to sun9i),
-	must be a multiple of 24. For the sun9i (A80), the tested values
-	(for DDR3-1600) are 312 to 792.
-
-if MACH_SUN5I || MACH_SUN7I
-config DRAM_MBUS_CLK
-	int "sunxi mbus clock speed"
-	default 300
-	---help---
-	Set the mbus clock speed. The maximum on sun5i hardware is 300MHz.
-
-endif
-
-config DRAM_ZQ
-	int "sunxi dram zq value"
-	default 123 if MACH_SUN4I || MACH_SUN5I || MACH_SUN6I || MACH_SUN8I
-	default 127 if MACH_SUN7I
-	default 3881979 if MACH_SUN8I_R40
-	default 4145117 if MACH_SUN9I
-	default 3881915 if MACH_SUN50I
-	---help---
-	Set the dram zq value.
-
-config DRAM_ODT_EN
-	bool "sunxi dram odt enable"
-	default n if !MACH_SUN8I_A23
-	default y if MACH_SUN8I_A23
-	default y if MACH_SUN8I_R40
-	default y if MACH_SUN50I
-	---help---
-	Select this to enable dram odt (on die termination).
-
-if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
-config DRAM_EMR1
-	int "sunxi dram emr1 value"
-	default 0 if MACH_SUN4I
-	default 4 if MACH_SUN5I || MACH_SUN7I
-	---help---
-	Set the dram controller emr1 value.
-
-config DRAM_TPR3
-	hex "sunxi dram tpr3 value"
-	default 0
-	---help---
-	Set the dram controller tpr3 parameter. This parameter configures
-	the delay on the command lane and also phase shifts, which are
-	applied for sampling incoming read data. The default value 0
-	means that no phase/delay adjustments are necessary. Properly
-	configuring this parameter increases reliability at high DRAM
-	clock speeds.
-
-config DRAM_DQS_GATING_DELAY
-	hex "sunxi dram dqs_gating_delay value"
-	default 0
-	---help---
-	Set the dram controller dqs_gating_delay parmeter. Each byte
-	encodes the DQS gating delay for each byte lane. The delay
-	granularity is 1/4 cycle. For example, the value 0x05060606
-	means that the delay is 5 quarter-cycles for one lane (1.25
-	cycles) and 6 quarter-cycles (1.5 cycles) for 3 other lanes.
-	The default value 0 means autodetection. The results of hardware
-	autodetection are not very reliable and depend on the chip
-	temperature (sometimes producing different results on cold start
-	and warm reboot). But the accuracy of hardware autodetection
-	is usually good enough, unless running at really high DRAM
-	clocks speeds (up to 600MHz). If unsure, keep as 0.
-
-choice
-	prompt "sunxi dram timings"
-	default DRAM_TIMINGS_VENDOR_MAGIC
-	---help---
-	Select the timings of the DDR3 chips.
-
-config DRAM_TIMINGS_VENDOR_MAGIC
-	bool "Magic vendor timings from Android"
-	---help---
-	The same DRAM timings as in the Allwinner boot0 bootloader.
-
-config DRAM_TIMINGS_DDR3_1066F_1333H
-	bool "JEDEC DDR3-1333H with down binning to DDR3-1066F"
-	---help---
-	Use the timings of the standard JEDEC DDR3-1066F speed bin for
-	DRAM_CLK <= 533MHz and the timings of the DDR3-1333H speed bin
-	for DRAM_CLK > 533MHz. This covers the majority of DDR3 chips
-	used in Allwinner A10/A13/A20 devices. In the case of DDR3-1333
-	or DDR3-1600 chips, be sure to check the DRAM datasheet to confirm
-	that down binning to DDR3-1066F is supported (because DDR3-1066F
-	uses a bit faster timings than DDR3-1333H).
-
-config DRAM_TIMINGS_DDR3_800E_1066G_1333J
-	bool "JEDEC DDR3-800E / DDR3-1066G / DDR3-1333J"
-	---help---
-	Use the timings of the slowest possible JEDEC speed bin for the
-	selected DRAM_CLK. Depending on the DRAM_CLK value, it may be
-	DDR3-800E, DDR3-1066G or DDR3-1333J.
-
-endchoice
-
-endif
-
-if MACH_SUN8I_A23
-config DRAM_ODT_CORRECTION
-	int "sunxi dram odt correction value"
-	default 0
-	---help---
-	Set the dram odt correction value (range -255 - 255). In allwinner
-	fex files, this option is found in bits 8-15 of the u32 odt_en variable
-	in the [dram] section. When bit 31 of the odt_en variable is set
-	then the correction is negative. Usually the value for this is 0.
-endif
-
-config SYS_CLK_FREQ
-	default 1008000000 if MACH_SUN4I
-	default 1008000000 if MACH_SUN5I
-	default 1008000000 if MACH_SUN6I
-	default 912000000 if MACH_SUN7I
-	default 1008000000 if MACH_SUN8I
-	default 1008000000 if MACH_SUN9I
-	default 816000000 if MACH_SUN50I
-
-config SYS_CONFIG_NAME
-	default "sun4i" if MACH_SUN4I
-	default "sun5i" if MACH_SUN5I
-	default "sun6i" if MACH_SUN6I
-	default "sun7i" if MACH_SUN7I
-	default "sun8i" if MACH_SUN8I
-	default "sun9i" if MACH_SUN9I
-	default "sun50i" if MACH_SUN50I
-
-config SYS_BOARD
-	default "sunxi"
-
-config SYS_SOC
-	default "sunxi"
-
-config UART0_PORT_F
-	bool "UART0 on MicroSD breakout board"
-	default n
-	---help---
-	Repurpose the SD card slot for getting access to the UART0 serial
-	console. Primarily useful only for low level u-boot debugging on
-	tablets, where normal UART0 is difficult to access and requires
-	device disassembly and/or soldering. As the SD card can't be used
-	at the same time, the system can be only booted in the FEL mode.
-	Only enable this if you really know what you are doing.
-
-config OLD_SUNXI_KERNEL_COMPAT
-	bool "Enable workarounds for booting old kernels"
-	default n
-	---help---
-	Set this to enable various workarounds for old kernels, this results in
-	sub-optimal settings for newer kernels, only enable if needed.
-
-config MACPWR
-	string "MAC power pin"
-	default ""
-	help
-	  Set the pin used to power the MAC. This takes a string in the format
-	  understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
-
-config MMC0_CD_PIN
-	string "Card detect pin for mmc0"
-	default "PF6" if MACH_SUN8I_A83T || MACH_SUNXI_H3_H5 || MACH_SUN50I
-	default ""
-	---help---
-	Set the card detect pin for mmc0, leave empty to not use cd. This
-	takes a string in the format understood by sunxi_name_to_gpio, e.g.
-	PH1 for pin 1 of port H.
-
-config MMC1_CD_PIN
-	string "Card detect pin for mmc1"
-	default ""
-	---help---
-	See MMC0_CD_PIN help text.
-
-config MMC2_CD_PIN
-	string "Card detect pin for mmc2"
-	default ""
-	---help---
-	See MMC0_CD_PIN help text.
-
-config MMC3_CD_PIN
-	string "Card detect pin for mmc3"
-	default ""
-	---help---
-	See MMC0_CD_PIN help text.
-
-config MMC1_PINS
-	string "Pins for mmc1"
-	default ""
-	---help---
-	Set the pins used for mmc1, when applicable. This takes a string in the
-	format understood by sunxi_name_to_gpio_bank, e.g. PH for port H.
-
-config MMC2_PINS
-	string "Pins for mmc2"
-	default ""
-	---help---
-	See MMC1_PINS help text.
-
-config MMC3_PINS
-	string "Pins for mmc3"
-	default ""
-	---help---
-	See MMC1_PINS help text.
-
-config MMC_SUNXI_SLOT_EXTRA
-	int "mmc extra slot number"
-	default -1
-	---help---
-	sunxi builds always enable mmc0, some boards also have a second sdcard
-	slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable
-	support for this.
-
-config INITIAL_USB_SCAN_DELAY
-	int "delay initial usb scan by x ms to allow builtin devices to init"
-	default 0
-	---help---
-	Some boards have on board usb devices which need longer than the
-	USB spec's 1 second to connect from board powerup. Set this config
-	option to a non 0 value to add an extra delay before the first usb
-	bus scan.
-
-config USB0_VBUS_PIN
-	string "Vbus enable pin for usb0 (otg)"
-	default ""
-	---help---
-	Set the Vbus enable pin for usb0 (otg). This takes a string in the
-	format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
-
-config USB0_VBUS_DET
-	string "Vbus detect pin for usb0 (otg)"
-	default ""
-	---help---
-	Set the Vbus detect pin for usb0 (otg). This takes a string in the
-	format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
-
-config USB0_ID_DET
-	string "ID detect pin for usb0 (otg)"
-	default ""
-	---help---
-	Set the ID detect pin for usb0 (otg). This takes a string in the
-	format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
-
-config USB1_VBUS_PIN
-	string "Vbus enable pin for usb1 (ehci0)"
-	default "PH6" if MACH_SUN4I || MACH_SUN7I
-	default "PH27" if MACH_SUN6I
-	---help---
-	Set the Vbus enable pin for usb1 (ehci0, usb0 is the otg). This takes
-	a string in the format understood by sunxi_name_to_gpio, e.g.
-	PH1 for pin 1 of port H.
-
-config USB2_VBUS_PIN
-	string "Vbus enable pin for usb2 (ehci1)"
-	default "PH3" if MACH_SUN4I || MACH_SUN7I
-	default "PH24" if MACH_SUN6I
-	---help---
-	See USB1_VBUS_PIN help text.
-
-config USB3_VBUS_PIN
-	string "Vbus enable pin for usb3 (ehci2)"
-	default ""
-	---help---
-	See USB1_VBUS_PIN help text.
-
-config I2C0_ENABLE
-	bool "Enable I2C/TWI controller 0"
-	default y if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I_R40
-	default n if MACH_SUN6I || MACH_SUN8I
-	select CMD_I2C
-	---help---
-	This allows enabling I2C/TWI controller 0 by muxing its pins, enabling
-	its clock and setting up the bus. This is especially useful on devices
-	with slaves connected to the bus or with pins exposed through e.g. an
-	expansion port/header.
-
-config I2C1_ENABLE
-	bool "Enable I2C/TWI controller 1"
-	default n
-	select CMD_I2C
-	---help---
-	See I2C0_ENABLE help text.
-
-config I2C2_ENABLE
-	bool "Enable I2C/TWI controller 2"
-	default n
-	select CMD_I2C
-	---help---
-	See I2C0_ENABLE help text.
-
-if MACH_SUN6I || MACH_SUN7I
-config I2C3_ENABLE
-	bool "Enable I2C/TWI controller 3"
-	default n
-	select CMD_I2C
-	---help---
-	See I2C0_ENABLE help text.
-endif
-
-if SUNXI_GEN_SUN6I
-config R_I2C_ENABLE
-	bool "Enable the PRCM I2C/TWI controller"
-	# This is used for the pmic on H3
-	default y if SY8106A_POWER
-	select CMD_I2C
-	---help---
-	Set this to y to enable the I2C controller which is part of the PRCM.
-endif
-
-if MACH_SUN7I
-config I2C4_ENABLE
-	bool "Enable I2C/TWI controller 4"
-	default n
-	select CMD_I2C
-	---help---
-	See I2C0_ENABLE help text.
-endif
-
-config AXP_GPIO
-	bool "Enable support for gpio-s on axp PMICs"
-	default n
-	---help---
-	Say Y here to enable support for the gpio pins of the axp PMIC ICs.
-
-config VIDEO
-	bool "Enable graphical uboot console on HDMI, LCD or VGA"
-	depends on !MACH_SUN8I_A83T
-	depends on !MACH_SUNXI_H3_H5
-	depends on !MACH_SUN8I_R40
-	depends on !MACH_SUN8I_V3S
-	depends on !MACH_SUN9I
-	depends on !MACH_SUN50I
-	default y
-	---help---
-	Say Y here to add support for using a cfb console on the HDMI, LCD
-	or VGA output found on most sunxi devices. See doc/README.video for
-	info on how to select the video output and mode.
-
-config VIDEO_HDMI
-	bool "HDMI output support"
-	depends on VIDEO && !MACH_SUN8I
-	default y
-	---help---
-	Say Y here to add support for outputting video over HDMI.
-
-config VIDEO_VGA
-	bool "VGA output support"
-	depends on VIDEO && (MACH_SUN4I || MACH_SUN7I)
-	default n
-	---help---
-	Say Y here to add support for outputting video over VGA.
-
-config VIDEO_VGA_VIA_LCD
-	bool "VGA via LCD controller support"
-	depends on VIDEO && (MACH_SUN5I || MACH_SUN6I || MACH_SUN8I)
-	default n
-	---help---
-	Say Y here to add support for external DACs connected to the parallel
-	LCD interface driving a VGA connector, such as found on the
-	Olimex A13 boards.
-
-config VIDEO_VGA_VIA_LCD_FORCE_SYNC_ACTIVE_HIGH
-	bool "Force sync active high for VGA via LCD controller support"
-	depends on VIDEO_VGA_VIA_LCD
-	default n
-	---help---
-	Say Y here if you've a board which uses opendrain drivers for the vga
-	hsync and vsync signals. Opendrain drivers cannot generate steep enough
-	positive edges for a stable video output, so on boards with opendrain
-	drivers the sync signals must always be active high.
-
-config VIDEO_VGA_EXTERNAL_DAC_EN
-	string "LCD panel power enable pin"
-	depends on VIDEO_VGA_VIA_LCD
-	default ""
-	---help---
-	Set the enable pin for the external VGA DAC. This takes a string in the
-	format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
-
-config VIDEO_COMPOSITE
-	bool "Composite video output support"
-	depends on VIDEO && (MACH_SUN4I || MACH_SUN5I || MACH_SUN7I)
-	default n
-	---help---
-	Say Y here to add support for outputting composite video.
-
-config VIDEO_LCD_MODE
-	string "LCD panel timing details"
-	depends on VIDEO
-	default ""
-	---help---
-	LCD panel timing details string, leave empty if there is no LCD panel.
-	This is in drivers/video/videomodes.c: video_get_params() format, e.g.
-	x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:0,vmode:0
-	Also see: http://linux-sunxi.org/LCD
-
-config VIDEO_LCD_DCLK_PHASE
-	int "LCD panel display clock phase"
-	depends on VIDEO
-	default 1
-	---help---
-	Select LCD panel display clock phase shift, range 0-3.
-
-config VIDEO_LCD_POWER
-	string "LCD panel power enable pin"
-	depends on VIDEO
-	default ""
-	---help---
-	Set the power enable pin for the LCD panel. This takes a string in the
-	format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
-
-config VIDEO_LCD_RESET
-	string "LCD panel reset pin"
-	depends on VIDEO
-	default ""
-	---help---
-	Set the reset pin for the LCD panel. This takes a string in the format
-	understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
-
-config VIDEO_LCD_BL_EN
-	string "LCD panel backlight enable pin"
-	depends on VIDEO
-	default ""
-	---help---
-	Set the backlight enable pin for the LCD panel. This takes a string in the
-	the format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of
-	port H.
-
-config VIDEO_LCD_BL_PWM
-	string "LCD panel backlight pwm pin"
-	depends on VIDEO
-	default ""
-	---help---
-	Set the backlight pwm pin for the LCD panel. This takes a string in the
-	format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
-
-config VIDEO_LCD_BL_PWM_ACTIVE_LOW
-	bool "LCD panel backlight pwm is inverted"
-	depends on VIDEO
-	default y
-	---help---
-	Set this if the backlight pwm output is active low.
-
-config VIDEO_LCD_PANEL_I2C
-	bool "LCD panel needs to be configured via i2c"
-	depends on VIDEO
-	default n
-	select CMD_I2C
-	---help---
-	Say y here if the LCD panel needs to be configured via i2c. This
-	will add a bitbang i2c controller using gpios to talk to the LCD.
-
-config VIDEO_LCD_PANEL_I2C_SDA
-	string "LCD panel i2c interface SDA pin"
-	depends on VIDEO_LCD_PANEL_I2C
-	default "PG12"
-	---help---
-	Set the SDA pin for the LCD i2c interface. This takes a string in the
-	format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
-
-config VIDEO_LCD_PANEL_I2C_SCL
-	string "LCD panel i2c interface SCL pin"
-	depends on VIDEO_LCD_PANEL_I2C
-	default "PG10"
-	---help---
-	Set the SCL pin for the LCD i2c interface. This takes a string in the
-	format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
-
-
-# Note only one of these may be selected at a time! But hidden choices are
-# not supported by Kconfig
-config VIDEO_LCD_IF_PARALLEL
-	bool
-
-config VIDEO_LCD_IF_LVDS
-	bool
-
-config SUNXI_DE2
-	bool
-	default n
-
-config VIDEO_DE2
-	bool "Display Engine 2 video driver"
-	depends on SUNXI_DE2
-	select DM_VIDEO
-	select DISPLAY
-	default y
-	---help---
-	Say y here if you want to build DE2 video driver which is present on
-	newer SoCs. Currently only HDMI output is supported.
-
-
-choice
-	prompt "LCD panel support"
-	depends on VIDEO
-	---help---
-	Select which type of LCD panel to support.
-
-config VIDEO_LCD_PANEL_PARALLEL
-	bool "Generic parallel interface LCD panel"
-	select VIDEO_LCD_IF_PARALLEL
-
-config VIDEO_LCD_PANEL_LVDS
-	bool "Generic lvds interface LCD panel"
-	select VIDEO_LCD_IF_LVDS
-
-config VIDEO_LCD_PANEL_MIPI_4_LANE_513_MBPS_VIA_SSD2828
-	bool "MIPI 4-lane, 513Mbps LCD panel via SSD2828 bridge chip"
-	select VIDEO_LCD_SSD2828
-	select VIDEO_LCD_IF_PARALLEL
-	---help---
-	7.85" 768x1024 LCD panels, such as LG LP079X01 or AUO B079XAN01.0
-
-config VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804
-	bool "eDP 4-lane, 1.62G LCD panel via ANX9804 bridge chip"
-	select VIDEO_LCD_ANX9804
-	select VIDEO_LCD_IF_PARALLEL
-	select VIDEO_LCD_PANEL_I2C
-	---help---
-	Select this for eDP LCD panels with 4 lanes running at 1.62G,
-	connected via an ANX9804 bridge chip.
-
-config VIDEO_LCD_PANEL_HITACHI_TX18D42VM
-	bool "Hitachi tx18d42vm LCD panel"
-	select VIDEO_LCD_HITACHI_TX18D42VM
-	select VIDEO_LCD_IF_LVDS
-	---help---
-	7.85" 1024x768 Hitachi tx18d42vm LCD panel support
-
-config VIDEO_LCD_TL059WV5C0
-	bool "tl059wv5c0 LCD panel"
-	select VIDEO_LCD_PANEL_I2C
-	select VIDEO_LCD_IF_PARALLEL
-	---help---
-	6" 480x800 tl059wv5c0 panel support, as used on the Utoo P66 and
-	Aigo M60/M608/M606 tablets.
-
-endchoice
-
-config SATAPWR
-	string "SATA power pin"
-	default ""
-	help
-	  Set the pins used to power the SATA. This takes a string in the
-	  format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of
-	  port H.
-
-config GMAC_TX_DELAY
-	int "GMAC Transmit Clock Delay Chain"
-	default 0
-	---help---
-	Set the GMAC Transmit Clock Delay Chain value.
-
-config SPL_STACK_R_ADDR
-	default 0x4fe00000 if MACH_SUN4I
-	default 0x4fe00000 if MACH_SUN5I
-	default 0x4fe00000 if MACH_SUN6I
-	default 0x4fe00000 if MACH_SUN7I
-	default 0x4fe00000 if MACH_SUN8I
-	default 0x2fe00000 if MACH_SUN9I
-	default 0x4fe00000 if MACH_SUN50I
-
-endif