diff options
author | Simon Guinot <simon.guinot@sequanux.org> | 2012-09-06 10:51:42 (GMT) |
---|---|---|
committer | Prafulla Wadaskar <prafulla@marvell.com> | 2012-10-03 11:13:12 (GMT) |
commit | 37235496950360eb695214683f02f5975b010bd1 (patch) | |
tree | 62c9fc7aa0c0d52d304c21575d9d8fcc5fd46e0f /board | |
parent | 8e6224364e85950cc308f6ab19eacf957abd94de (diff) | |
download | u-boot-37235496950360eb695214683f02f5975b010bd1.tar.xz |
ARM: add support for Network Space v2 Lite and Mini
This patch adds support for the LaCie boards Network Space v2 (Lite and
Mini). This two boards are derived from the Network Space v2 and a lot
of hardware caracteristics are shared.
- CPU: Marvell 88F6192 800Mhz
- SDRAM memory: 128MB DDR2 200Mhz
- 1 SATA port: internal
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports (Lite only): host and host/device
- 1 push button
- 1 SATA LED (bi-color, blue and red)
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Diffstat (limited to 'board')
-rw-r--r-- | board/LaCie/common/common.c | 36 | ||||
-rw-r--r-- | board/LaCie/common/common.h | 1 | ||||
-rw-r--r-- | board/LaCie/netspace_v2/kwbimage-ns2l.cfg | 162 | ||||
-rw-r--r-- | board/LaCie/netspace_v2/netspace_v2.c | 4 |
4 files changed, 200 insertions, 3 deletions
diff --git a/board/LaCie/common/common.c b/board/LaCie/common/common.c index 78d0edc..a62bf9f 100644 --- a/board/LaCie/common/common.c +++ b/board/LaCie/common/common.c @@ -13,10 +13,11 @@ #if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R) +#define MII_MARVELL_PHY_PAGE 22 + #define MV88E1116_LED_FCTRL_REG 10 #define MV88E1116_CPRSP_CR3_REG 21 #define MV88E1116_MAC_CTRL_REG 21 -#define MV88E1116_PGADR_REG 22 #define MV88E1116_RGMII_TXTM_CTRL (1 << 4) #define MV88E1116_RGMII_RXTM_CTRL (1 << 5) @@ -31,15 +32,44 @@ void mv_phy_88e1116_init(const char *name, u16 phyaddr) * Enable RGMII delay on Tx and Rx for CPU port * Ref: sec 4.7.2 of chip datasheet */ - miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 2); + miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 2); miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL_REG, ®); reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL_REG, reg); - miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 0); + miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 0); if (miiphy_reset(name, phyaddr) == 0) printf("88E1116 Initialized on %s\n", name); } + +void mv_phy_88e1318_init(const char *name, u16 phyaddr) +{ + u16 reg; + + if (miiphy_set_current_dev(name)) + return; + + /* + * Set control mode 4 for LED[0]. + */ + miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 3); + miiphy_read(name, phyaddr, 16, ®); + reg |= 0xf; + miiphy_write(name, phyaddr, 16, reg); + + /* + * Enable RGMII delay on Tx and Rx for CPU port + * Ref: sec 4.7.2 of chip datasheet + */ + miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 2); + miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL_REG, ®); + reg |= (MV88E1116_RGMII_TXTM_CTRL | MV88E1116_RGMII_RXTM_CTRL); + miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL_REG, reg); + miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 0); + + if (miiphy_reset(name, phyaddr) == 0) + printf("88E1318 Initialized on %s\n", name); +} #endif /* CONFIG_CMD_NET && CONFIG_RESET_PHY_R */ #if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR) diff --git a/board/LaCie/common/common.h b/board/LaCie/common/common.h index 2edd5ab..85e433c 100644 --- a/board/LaCie/common/common.h +++ b/board/LaCie/common/common.h @@ -12,6 +12,7 @@ #if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R) void mv_phy_88e1116_init(const char *name, u16 phyaddr); +void mv_phy_88e1318_init(const char *name, u16 phyaddr); #endif #if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR) int lacie_read_mac_address(uchar *mac); diff --git a/board/LaCie/netspace_v2/kwbimage-ns2l.cfg b/board/LaCie/netspace_v2/kwbimage-ns2l.cfg new file mode 100644 index 0000000..d008eb0 --- /dev/null +++ b/board/LaCie/netspace_v2/kwbimage-ns2l.cfg @@ -0,0 +1,162 @@ +# +# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com> +# +# Based on Kirkwood support: +# (C) Copyright 2009 +# Marvell Semiconductor <www.marvell.com> +# Written-by: Prafulla Wadaskar <prafulla@marvell.com> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# Refer docs/README.kwimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM spi # Boot from SPI flash + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0 interface pad voltage to 1.8V +DATA 0xFFD100e0 0x1B1B1B9B + +#Dram initalization for SINGLE x16 CL=5 @ 400MHz +DATA 0xFFD01400 0x43000618 # DDR Configuration register +# bit13-0: 0xa00 (2560 DDR2 clks refresh rate) +# bit23-14: zero +# bit24: 1= enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: zero +# bit31-30: 01 + +DATA 0xFFD01404 0x34143000 # DDR Controller Control Low +# bit 4: 0=addr/cmd in smame cycle +# bit 5: 0=clk is driven during self refresh, we don't care for APX +# bit 6: 0=use recommended falling edge of clk for addr/cmd +# bit14: 0=input buffer always powered up +# bit18: 1=cpu lock transaction enabled +# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0=no additional STARTBURST delay + +DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1) +# bit7-4: TRCD +# bit11- 8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xFFD0140C 0x00000A19 # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: zero required + +DATA 0xFFD01410 0x0000DDDD # DDR Address Control +# bit1-0: 00, Cs0width=x8 +# bit3-2: 10, Cs0size=512Mb +# bit5-4: 00, Cs2width=nonexistent +# bit7-6: 00, Cs1size =nonexistent +# bit9-8: 00, Cs2width=nonexistent +# bit11-10: 00, Cs2size =nonexistent +# bit13-12: 00, Cs3width=nonexistent +# bit15-14: 00, Cs3size =nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000632 # DDR Mode +# bit2-0: 2, BurstLen=2 required +# bit3: 0, BurstType=0 required +# bit6-4: 4, CL=5 +# bit7: 0, TestMode=0 normal +# bit8: 0, DLL reset=0 normal +# bit11-9: 6, auto-precharge write recovery ???????????? +# bit12: 0, PD must be zero +# bit31-13: 0 required + +DATA 0xFFD01420 0x00000004 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 1, DDR drive strenght reduced +# bit2: 1, DDR ODT control lsd enabled +# bit5-3: 000, required +# bit6: 1, DDR ODT control msb, enabled +# bit9-7: 000, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F07F # DDR Controller Control High +# bit2-0: 111, required +# bit3 : 1 , MBUS Burst Chop disabled +# bit6-4: 111, required +# bit7 : 1 , D2P Latency enabled +# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz +# bit9 : 0 , no half clock cycle addition to dataout +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh +# bit15-12: 1111 required +# bit31-16: 0 required + +DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) +DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 00, CS0 hit selected +# bit23-4: ones, required +# bit31-24: 0x07, Size (i.e. 128MB) + +DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low) +# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0 +# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 + +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above +# bit3-2: 01, ODT1 active NEVER! +# bit31-4: zero, required + +DATA 0xFFD0149C 0x0000E40F # CPU ODT Control +# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0 +# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0 +# bit11-10:1, DQ_ODTSel. ODT select turned on + +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +#bit0=1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 diff --git a/board/LaCie/netspace_v2/netspace_v2.c b/board/LaCie/netspace_v2/netspace_v2.c index 68e8a77..101a80a 100644 --- a/board/LaCie/netspace_v2/netspace_v2.c +++ b/board/LaCie/netspace_v2/netspace_v2.c @@ -107,7 +107,11 @@ int misc_init_r(void) /* Configure and initialize PHY */ void reset_phy(void) { +#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2) + mv_phy_88e1318_init("egiga0", 0); +#else mv_phy_88e1116_init("egiga0", 8); +#endif } #endif |