powerpc: ppc4xx: remove p3p440 support

This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stefan Roese <sr@denx.de>

7 files changed, 0 insertions, 282 deletions

diff --git a/board/prodrive/p3p440/Kconfig b/board/prodrive/p3p440/Kconfig
deleted file mode 100644
index cf53aac..0000000
--- a/board/prodrive/p3p440/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_P3P440
-
-config SYS_BOARD
-	default "p3p440"
-
-config SYS_VENDOR
-	default "prodrive"
-
-config SYS_CONFIG_NAME
-	default "p3p440"
-
-endif
diff --git a/board/prodrive/p3p440/MAINTAINERS b/board/prodrive/p3p440/MAINTAINERS
deleted file mode 100644
index 68fd1a9..0000000
--- a/board/prodrive/p3p440/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-P3P440 BOARD
-M:	Stefan Roese <sr@denx.de>
-S:	Maintained
-F:	board/prodrive/p3p440/
-F:	include/configs/p3p440.h
-F:	configs/p3p440_defconfig
diff --git a/board/prodrive/p3p440/Makefile b/board/prodrive/p3p440/Makefile
deleted file mode 100644
index d62f75d..0000000
--- a/board/prodrive/p3p440/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# (C) Copyright 2002-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	= p3p440.o
-extra-y	+= init.o
diff --git a/board/prodrive/p3p440/config.mk b/board/prodrive/p3p440/config.mk
deleted file mode 100644
index f18b097..0000000
--- a/board/prodrive/p3p440/config.mk
+++ /dev/null
@@ -1,16 +0,0 @@
-#
-# (C) Copyright 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-PLATFORM_CPPFLAGS += -DCONFIG_440=1
-
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG
-endif
-
-ifeq ($(dbcr),1)
-PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000
-endif
diff --git a/board/prodrive/p3p440/init.S b/board/prodrive/p3p440/init.S
deleted file mode 100644
index 35b1afa..0000000
--- a/board/prodrive/p3p440/init.S
+++ /dev/null
@@ -1,38 +0,0 @@
-/*
- * (C) Copyright 2005
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <ppc_asm.tmpl>
-#include <asm/mmu.h>
-#include <config.h>
-#include <asm/ppc4xx.h>
-
-/**************************************************************************
- * TLB TABLE
- *
- * This table is used by the cpu boot code to setup the initial tlb
- * entries. Rather than make broad assumptions in the cpu source tree,
- * this table lets each board set things up however they like.
- *
- *  Pointer to the table is returned in r1
- *
- *************************************************************************/
-
-    .section .bootpg,"ax"
-    .globl tlbtab
-
-tlbtab:
-    tlbtab_start
-    tlbentry( 0xf0000000, SZ_256M, 0xf0000000, 1, AC_RWX | SA_IG)
-    tlbentry( CONFIG_SYS_PERIPHERAL_BASE, SZ_256M, 0x40000000, 1, AC_RW | SA_IG)
-    tlbentry( CONFIG_SYS_ISRAM_BASE, SZ_4K, 0x80000000, 0, AC_RWX )
-    tlbentry( CONFIG_SYS_ISRAM_BASE + 0x1000, SZ_4K, 0x80001000, 0, AC_RWX )
-    tlbentry( CONFIG_SYS_SDRAM_BASE, SZ_256M, 0x00000000, 0, AC_RWX | SA_IG )
-    tlbentry( CONFIG_SYS_PCI_BASE, SZ_256M, 0x00000000, 2, AC_RW | SA_IG )
-    tlbentry( CONFIG_SYS_PCI_MEMBASE, SZ_256M, 0x00000000, 3, AC_RW | SA_IG )
-    tlbtab_end
diff --git a/board/prodrive/p3p440/p3p440.c b/board/prodrive/p3p440/p3p440.c
deleted file mode 100644
index 929e8eb..0000000
--- a/board/prodrive/p3p440/p3p440.c
+++ /dev/null
@@ -1,177 +0,0 @@
-/*
- * (C) Copyright 2005
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/processor.h>
-#include <command.h>
-
-#include "p3p440.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-void set_led(int color)
-{
-	switch (color) {
-	case LED_OFF:
-		out32(GPIO0_OR,  in32(GPIO0_OR) & ~CONFIG_SYS_LED_GREEN & ~CONFIG_SYS_LED_RED);
-		break;
-
-	case LED_GREEN:
-		out32(GPIO0_OR,  (in32(GPIO0_OR) | CONFIG_SYS_LED_GREEN) & ~CONFIG_SYS_LED_RED);
-		break;
-
-	case LED_RED:
-		out32(GPIO0_OR,  (in32(GPIO0_OR) | CONFIG_SYS_LED_RED) & ~CONFIG_SYS_LED_GREEN);
-		break;
-
-	case LED_ORANGE:
-		out32(GPIO0_OR,  in32(GPIO0_OR) | CONFIG_SYS_LED_GREEN | CONFIG_SYS_LED_RED);
-		break;
-	}
-}
-
-static int is_monarch(void)
-{
-	out32(GPIO0_OR,  in32(GPIO0_OR) & ~CONFIG_SYS_GPIO_RDY);
-	udelay(1000);
-
-	if (in32(GPIO0_IR) & CONFIG_SYS_MONARCH_IO)
-		return 0;
-	else
-		return 1;
-}
-
-static void wait_for_pci_ready(void)
-{
-	/*
-	 * Configure EREADY_IO as input
-	 */
-	out32(GPIO0_TCR, in32(GPIO0_TCR) & ~CONFIG_SYS_EREADY_IO);
-	udelay(1000);
-
-	for (;;) {
-		if (in32(GPIO0_IR) & CONFIG_SYS_EREADY_IO)
-			return;
-	}
-
-}
-
-int board_early_init_f(void)
-{
-	uint reg;
-
-	/*--------------------------------------------------------------------
-	 * Setup the external bus controller/chip selects
-	 *-------------------------------------------------------------------*/
-	mtdcr(EBC0_CFGADDR, EBC0_CFG);
-	reg = mfdcr(EBC0_CFGDATA);
-	mtdcr(EBC0_CFGDATA, reg | 0x04000000);	/* Set ATC */
-
-	/*--------------------------------------------------------------------
-	 * Setup pin multiplexing (GPIO/IRQ...)
-	 *-------------------------------------------------------------------*/
-	mtdcr(CPC0_GPIO, 0x03F01F80);
-
-	out32(GPIO0_ODR, 0x00000000);	/* no open drain pins      */
-	out32(GPIO0_TCR, CONFIG_SYS_GPIO_RDY | CONFIG_SYS_EREADY_IO | CONFIG_SYS_LED_RED | CONFIG_SYS_LED_GREEN);
-	out32(GPIO0_OR,  CONFIG_SYS_GPIO_RDY);
-
-	/*--------------------------------------------------------------------
-	 * Setup the interrupt controller polarities, triggers, etc.
-	 *-------------------------------------------------------------------*/
-	mtdcr(UIC0SR, 0xffffffff);	/* clear all */
-	mtdcr(UIC0ER, 0x00000000);	/* disable all */
-	mtdcr(UIC0CR, 0x00000001);	/* UIC1 crit is critical */
-	mtdcr(UIC0PR, 0xfffffe13);	/* per ref-board manual */
-	mtdcr(UIC0TR, 0x01c00008);	/* per ref-board manual */
-	mtdcr(UIC0VR, 0x00000001);	/* int31 highest, base=0x000 */
-	mtdcr(UIC0SR, 0xffffffff);	/* clear all */
-
-	mtdcr(UIC1SR, 0xffffffff);	/* clear all */
-	mtdcr(UIC1ER, 0x00000000);	/* disable all */
-	mtdcr(UIC1CR, 0x00000000);	/* all non-critical */
-	mtdcr(UIC1PR, 0xffffe0ff);	/* per ref-board manual */
-	mtdcr(UIC1TR, 0x00ffc000);	/* per ref-board manual */
-	mtdcr(UIC1VR, 0x00000001);	/* int31 highest, base=0x000 */
-	mtdcr(UIC1SR, 0xffffffff);	/* clear all */
-
-	return 0;
-}
-
-int checkboard(void)
-{
-	char buf[64];
-	int i = getenv_f("serial#", buf, sizeof(buf));
-
-	printf("Board: P3P440");
-	if (i > 0) {
-		puts(", serial# ");
-		puts(buf);
-	}
-
-	if (is_monarch()) {
-		puts(", Monarch");
-	} else {
-		puts(", None-Monarch");
-	}
-
-	putc('\n');
-
-	return (0);
-}
-
-int misc_init_r (void)
-{
-	/*
-	 * Adjust flash start and offset to detected values
-	 */
-	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
-	gd->bd->bi_flashoffset = 0;
-
-	/*
-	 * Check if only one FLASH bank is available
-	 */
-	if (gd->bd->bi_flashsize != CONFIG_SYS_MAX_FLASH_BANKS * (0 - CONFIG_SYS_FLASH0)) {
-		mtebc(PB1CR, 0);			/* disable cs */
-		mtebc(PB1AP, 0);
-		mtebc(PB2CR, 0);			/* disable cs */
-		mtebc(PB2AP, 0);
-		mtebc(PB3CR, 0);			/* disable cs */
-		mtebc(PB3AP, 0);
-	}
-
-	return 0;
-}
-
-/*************************************************************************
- * Override weak is_pci_host()
- *
- *	This routine is called to determine if a pci scan should be
- *	performed. With various hardware environments (especially cPCI and
- *	PPMC) it's insufficient to depend on the state of the arbiter enable
- *	bit in the strap register, or generic host/adapter assumptions.
- *
- *	Rather than hard-code a bad assumption in the general 440 code, the
- *	440 pci code requires the board to decide at runtime.
- *
- *	Return 0 for adapter mode, non-zero for host (monarch) mode.
- *
- *
- ************************************************************************/
-#if defined(CONFIG_PCI)
-int is_pci_host(struct pci_controller *hose)
-{
-	if (is_monarch()) {
-		wait_for_pci_ready();
-		return 1;		/* return 1 for host controller */
-	} else {
-		return 0;		/* return 0 for adapter controller */
-	}
-}
-#endif				/* defined(CONFIG_PCI) */
diff --git a/board/prodrive/p3p440/p3p440.h b/board/prodrive/p3p440/p3p440.h
deleted file mode 100644
index a164f95..0000000
--- a/board/prodrive/p3p440/p3p440.h
+++ /dev/null
@@ -1,24 +0,0 @@
-/*
- * (C) Copyright 2005
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __P3P440_H__
-#define __P3P440_H__
-
-#define CONFIG_SYS_GPIO_RDY	(0x80000000 >> 11)
-#define CONFIG_SYS_MONARCH_IO	(0x80000000 >> 18)
-#define CONFIG_SYS_EREADY_IO	(0x80000000 >> 20)
-#define CONFIG_SYS_LED_GREEN	(0x80000000 >> 21)
-#define CONFIG_SYS_LED_RED	(0x80000000 >> 22)
-
-#define LED_OFF		1
-#define LED_GREEN	2
-#define LED_RED		3
-#define LED_ORANGE	4
-
-long int fixed_sdram(void);
-
-#endif /* __P3P440_H__ */