diff options
author | Haiying Wang <Haiying.Wang@freescale.com> | 2009-03-27 21:02:45 (GMT) |
---|---|---|
committer | Kumar Gala <galak@kernel.crashing.org> | 2009-03-30 18:33:51 (GMT) |
commit | 765547dc5e0e8cbe6b8f4ea8a5d6ff237935c352 (patch) | |
tree | f16d2f492684da69eb33c571258f6447ea987708 /include | |
parent | 22b6dbc1696d927d938dd4e16f65d83c0d4fb3f4 (diff) | |
download | u-boot-765547dc5e0e8cbe6b8f4ea8a5d6ff237935c352.tar.xz |
MPC85xx: Add MPC8569MDS board support
This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD
EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Diffstat (limited to 'include')
-rw-r--r-- | include/configs/MPC8569MDS.h | 454 |
1 files changed, 454 insertions, 0 deletions
diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h new file mode 100644 index 0000000..b0af5dc --- /dev/null +++ b/include/configs/MPC8569MDS.h @@ -0,0 +1,454 @@ +/* + * Copyright (C) 2009 Freescale Semiconductor, Inc. All rights reserved. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * mpc8569mds board configuration file + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48/68 */ +#define CONFIG_MPC8569 1 /* MPC8569 specific */ +#define CONFIG_MPC8569MDS 1 /* MPC8569MDS board specific */ + +#define CONFIG_FSL_ELBC 1 /* Has Enhance localbus controller */ + +#define CONFIG_PCI 1 /* Disable PCI/PCIE */ +#define CONFIG_PCIE1 1 /* PCIE controller */ +#define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */ +#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ +#define CONFIG_QE /* Enable QE */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ + +/* + * When initializing flash, if we cannot find the manufacturer ID, + * assume this is the AMD flash associated with the MDS board. + * This allows booting from a promjet. + */ +#define CONFIG_ASSUME_AMD_FLASH + +#ifndef __ASSEMBLY__ +extern unsigned long get_clock_freq(void); +#endif +/* Replace a call to get_clock_freq (after it is implemented)*/ +#define CONFIG_SYS_CLK_FREQ 66000000 +#define CONFIG_DDR_CLK_FREQ 66000000 + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ + +/* + * Only possible on E500 Version 2 or newer cores. + */ +#define CONFIG_ENABLE_36BIT_PHYS 1 + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ + +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR + /* physical addr of CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR + /* PQII uses CONFIG_SYS_IMMR */ + +#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) +#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000) + +/* DDR Setup */ +#define CONFIG_FSL_DDR3 +#undef CONFIG_FSL_DDR_INTERACTIVE +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ +#define CONFIG_DDR_SPD +#define CONFIG_DDR_DLL /* possible DLL fix needed */ +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ + +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 + /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_NUM_DDR_CONTROLLERS 1 +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) + +/* I2C addresses of SPD EEPROMs */ +#define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ +#define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 1 DIMM 0 */ + +/* These are used when DDR doesn't use SPD. */ +#define CONFIG_SYS_SDRAM_SIZE 1024 /* DDR is 1024MB */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F +#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 +#define CONFIG_SYS_DDR_TIMING_3 0x00020000 +#define CONFIG_SYS_DDR_TIMING_0 0x00330004 +#define CONFIG_SYS_DDR_TIMING_1 0x6F6B4644 +#define CONFIG_SYS_DDR_TIMING_2 0x002888D0 +#define CONFIG_SYS_DDR_SDRAM_CFG 0x47000000 +#define CONFIG_SYS_DDR_SDRAM_CFG_2 0x04401040 +#define CONFIG_SYS_DDR_SDRAM_MODE 0x40401521 +#define CONFIG_SYS_DDR_SDRAM_MODE_2 0x8000C000 +#define CONFIG_SYS_DDR_SDRAM_INTERVAL 0x03E00000 +#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL 0x01000000 +#define CONFIG_SYS_DDR_TIMING_4 0x00220001 +#define CONFIG_SYS_DDR_TIMING_5 0x03402400 +#define CONFIG_SYS_DDR_ZQ_CNTL 0x89080600 +#define CONFIG_SYS_DDR_WRLVL_CNTL 0x0655A604 +#define CONFIG_SYS_DDR_CDR_1 0x80040000 +#define CONFIG_SYS_DDR_CDR_2 0x00000000 +#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 +#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 +#define CONFIG_SYS_DDR_CONTROL 0xc7000000 /* Type = DDR3 */ +#define CONFIG_SYS_DDR_CONTROL2 0x24400000 + +#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d +#define CONFIG_SYS_DDR_ERR_DIS 0x00000000 +#define CONFIG_SYS_DDR_SBE 0x00010000 + +#undef CONFIG_CLOCKS_IN_MHZ + +/* + * Local Bus Definitions + */ + +#define CONFIG_SYS_FLASH_BASE 0xfe000000 /* start of FLASH 32M */ +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE + +#define CONFIG_SYS_BCSR_BASE 0xf8000000 +#define CONFIG_SYS_BCSR_BASE_PHYS CONFIG_SYS_BCSR_BASE + +/*Chip select 0 - Flash*/ +#define CONFIG_SYS_BR0_PRELIM 0xfe000801 +#define CONFIG_SYS_OR0_PRELIM 0xfe000ff7 + +/*Chip slelect 1 - BCSR*/ +#define CONFIG_SYS_BR1_PRELIM 0xf8000801 +#define CONFIG_SYS_OR1_PRELIM 0xffffe9f7 + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO + + +/* + * SDRAM on the LocalBus + */ +#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ +#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ + +#define CONFIG_SYS_LBC_LCRR 0x00000004 /* LB clock ratio reg */ +#define CONFIG_SYS_LBC_LBCR 0x00040000 /* LB config reg */ +#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ +#define CONFIG_SYS_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* Serial Port */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) + +/* Use the HUSH parser*/ +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#endif + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +#define CONFIG_SYS_64BIT_VSPRINTF 1 +#define CONFIG_SYS_64BIT_STRTOUL 1 + +/* + * I2C + */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support*/ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + +/* + * I2C2 EEPROM + */ +#define CONFIG_ID_EEPROM +#ifdef CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#endif +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_BUS_NUM 1 + +#define PLPPAR1_I2C_BIT_MASK 0x0000000F +#define PLPPAR1_I2C2_VAL 0x00000000 +#define PLPDIR1_I2C_BIT_MASK 0x0000000F +#define PLPDIR1_I2C2_VAL 0x0000000F + +/* + * General PCI + * Memory Addresses are mapped 1-1. I/O is mapped from 0 + */ +#define CONFIG_SYS_PCIE1_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xa0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xe2800000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xe2800000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ + +#define CONFIG_SYS_SRIO_MEM_VIRT 0xc0000000 +#define CONFIG_SYS_SRIO_MEM_BUS 0xc0000000 +#define CONFIG_SYS_SRIO_MEM_PHYS 0xc0000000 + +#ifdef CONFIG_QE +/* + * QE UEC ethernet configuration + */ + +#define CONFIG_MIIM_ADDRESS (CONFIG_SYS_CCSRBAR + 0x82120) +#define CONFIG_UEC_ETH +#define CONFIG_ETHPRIME "FSL UEC0" +#define CONFIG_PHY_MODE_NEED_CHANGE + +#define CONFIG_UEC_ETH1 /* GETH1 */ +#define CONFIG_HAS_ETH0 + +#ifdef CONFIG_UEC_ETH1 +#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ +#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE +#define CONFIG_SYS_UEC1_TX_CLK QE_CLK12 +#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH +#define CONFIG_SYS_UEC1_PHY_ADDR 7 +#define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_1000_RGMII_ID +#endif + +#define CONFIG_UEC_ETH2 /* GETH2 */ +#define CONFIG_HAS_ETH1 + +#ifdef CONFIG_UEC_ETH2 +#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ +#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE +#define CONFIG_SYS_UEC2_TX_CLK QE_CLK17 +#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH +#define CONFIG_SYS_UEC2_PHY_ADDR 1 +#define CONFIG_SYS_UEC2_INTERFACE_MODE ENET_1000_RGMII_ID +#endif + +#endif /* CONFIG_QE */ + +#if defined(CONFIG_PCI) + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ + +#endif /* CONFIG_PCI */ + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 256K(one sector) for env */ +#define CONFIG_ENV_SIZE 0x2000 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* QE microcode/firmware address */ +#define CONFIG_SYS_QE_FW_ADDR 0xfff00000 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_ELF +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_SETEXPR + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 2048 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) + /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 32 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) + /* Initial Memory map for Linux*/ + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_HOSTNAME mpc8569mds +#define CONFIG_ROOTPATH /nfsroot +#define CONFIG_BOOTFILE your.uImage + +#define CONFIG_SERVERIP 192.168.1.1 +#define CONFIG_GATEWAYIP 192.168.1.1 +#define CONFIG_NETMASK 255.255.255.0 + +#define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=600000\0" \ + "ramdiskfile=your.ramdisk.u-boot\0" \ + "fdtaddr=400000\0" \ + "fdtfile=your.fdt.dtb\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs\0" \ + "ramargs=setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs\0" \ + +#define CONFIG_NFSBOOTCOMMAND \ + "run nfsargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "run ramargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "bootm $loadaddr $ramdiskaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND + +#endif /* __CONFIG_H */ |